PPPedram Payandehnia

Pedram Payandehnia

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Pedram Payandehnia has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • 0.9V, 79.7dB SNDR, 2MHz-BW, Highly linear OTA-less 1-1 MASH VCO-based ΔΣ with a Novel Phase Quantization Noise Extraction Technique

    by Hamidreza Maghami, Pedram Payandehnia, Hossein Mirzaie, Ramin Zanbaghi, Siladitya Dey, Justin Goins, Kartikeya Mayaram, Terri S. Fiez

    In this paper a novel technique is introduced to extract the quantization noise of a multi-phase VCO-based quantizer (VCOQ) in the time domain as a PWM signal. Using this technique, a new highly linear VCO-based 1-1 MASH delta-sigma ADC structure is presented. This architecture does not require any OTA-based analog integrators or power hungry linearization methods. The first stage is a closed loop multi-phase VCO-based voltage-to-phase (V-to-P) converter and the second stage is an open loop multi-phase VCO-based voltage-to-frequency (V-to-F) converter. Using the proposed technique the phase quantization error of the first stage is extracted as a pulse signal and then fed to the second stage. The input of the first VCO is a very small amplitude signal and the input of the second VCO is a two-level PWM signal. Therefore, the VCO non-linearity does not limit the overall ADC performance, mitigating the need for power hungry linearization methods. The prototype achieves 2 nd order noise shaping with a DR/SFDR/SNR/SNDR of 82.7/88.7/80.3/79.7 dB for an input signal BW of 2 MHz. The fabricated design consumes 1.248 mW from a 0.9 V. supply.


  • Open Access

    High‐linearity SAR‐VCO MASH ΔΣ ADC with second‐order noise shaping

    by P. Payandehnia, H. Maghami, H. Mirzaie, G.C. Temes

    A novel 0‐2 Multi‐Stage Noise Shaping (MASH) analogue‐to‐digital converter (ADC) is proposed. The first stage is implemented using a 4‐bit SAR ADC. The second stage uses a voltage controlled oscillator (VCO)‐based quantiser (VCOQ). Unlike earlier VCOQs which provide first‐order noise shaping, the VCOQ proposed in this Letter achieves second‐order noise filtering. To implement this noise shaping, the quantisation noise of the VCOQ is extracted as a pulse‐width‐modulated signal, and it is fed back to the VCO input using a charge pump circuit. In the proposed scheme, the input signal to the VCO is small. Therefore, the linearity requirement of this block is relaxed. Also, any error related to the charge pump circuitry will be first‐order shaped at the output. Simulation results confirm the second‐order noise shaping of the output of the ADC, and an excellent (14‐bit signal‐to‐noise and distortion ratio) performance with the over‐sampling ratio of 16.


  • A 72.4-dB SNDR 92-dB SFDR Blocker Tolerant CT $\Delta\Sigma$ Modulator With Inherent DWA

    by Hossein Mirzaie, Hamidreza Maghami, Ramin Zanbaghi, Pedram Payandehnia, Kartikeya Mayaram, Terri S. Fiez

    This paper presents the design and implementation of a new blocker tolerant wideband continuous-time delta-sigma modulator. Using a customized digital integrator with inherent data-weighted averaging (DWA) at the back-end of the modulator, the power consumption of the quantizer is reduced while the speed of operation is increased. Additionally, by using a single amplifier biquad (SAB) structure in the loop filter, the number of op-amps is reduced, thus reducing the analog power consumption. Also, the modulator robustness to the out-of-band blocker is improved by increasing the number of levels in the digital integrator and feedback DACs. The out-of-band blocker tolerance is improved by 3 dB compared to a conventional CIFF-B delta-sigma modulator with a minimal increase in the power consumption. The proposed architecture has been implemented in a 65-nm CMOS technology and operates at a 250 MHz sampling frequency. It achieves 73.5 dB SNR, 72.4 dB SNDR, and 92 dB SFDR over a 7 MHz bandwidth and a Walden Figure-of-Merit (FoM) of 341 fJ/conversion.


  • A 0.49–13.3 MHz Tunable Fourth-Order LPF with Complex Poles Achieving 28.7 dBm OIP3

    by Pedram Payandehnia, Hamidreza Maghami, Hossein Mirzaie, Manjunath Kareppagoudr, Siladitya Dey, Massoud Tohidian, Gabor C. Temes

    A novel switched-capacitor low-pass filter architecture is presented. In the proposed scheme, a feedback path is added to a charge-rotating real-pole filter to implement complex poles. The selectivity is enhanced, and the in-band loss is reduced compared with the real-pole filter. The output thermal noise level and the tuning range are both close to those of the real-pole filter. These features make the filter suitable for high speed, low noise, and low power applications. A fourth-order filter prototype was implemented in a 180-nm CMOS technology. The measured in-band loss is reduced by 3.3 dB compared with that of a real-pole filter. The sampling rate of the filter is programmable from 65 to 300 MS/s with a constant dc gain. The 3-dB cut-off frequency of the filter can be tuned from 490 to 13.3 MHz with over 100-dB maximum stop-band rejection. The measured in-band third-order output intercept point is 28.7 dBm, and the averaged spot noise is 6.54 nV/√Hz. The filter consumes 4.3 mW from a 1.8 V supply.


  • Open Access

    Passive switched‐capacitor filter with complex poles for high‐speed applications

    by P. Payandehnia, H. Maghami, M. Kareppagoudr, G.C. Temes

    A novel complex‐pole switched‐capacitor lowpass filter topology is presented. The proposed scheme features sharper roll‐off in the frequency response and reduced in‐band loss compared with a real‐pole filter. It provides higher stop‐band rejection for the same bandwidth. Hence, the required filter order and chip area are reduced. These improvements are achieved without adding more active blocks to the real‐pole filter, and with minimal added complexity. The proposed filter has the same low‐output thermal noise level as the real‐pole filter. These features, combined with a wide‐frequency tuning range, make the filter suitable for high‐speed, low‐noise, and low‐power applications. A fourth‐order 200 MS/s filter prototype was designed in 0.18 µm Asahi Kasei Microdevices Corporation CMOS technology. Simulations verify that the average in‐band loss is reduced by 3.2 dB compared with the real‐pole filter. The 3 dB cut‐off frequency can be tuned from 470 kHz to 17.5 MHz with 100 dB maximum stop‐band rejection.


  • A noise-coupled time-interleaved delta-sigma modulator with shifted loop delays

    by Xin Meng, Yi Zhang, Tao He, Pedram Payandehnia, Gabor C. Temes

    Noise coupling and time interleaving are effective methods for expanding the bandwidth of the low-power wideband delta-sigma modulators. In this paper, a discrete-time ΔΣ modulator topology with these two technologies, combined with shifted loop delays, is proposed. Noise coupling and time interleaving between the two channels enhance the effective order of the noise shaping function. Shifting the loop delays relaxes the critical timing for the DEM. Also, the last integrator in the loop filter performs both integration and active summation. To verify the effectiveness of this topology, a third-order noise-coupled time-interleaved ΔΣ modulator with shifted loop delays is analyzed and simulated.