Martin Wåhlander
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Martin Wåhlander has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Eva Malmström
KTH Royal Institute of Technology
6 shared publications - Fritjof Nilsson
School of Engineering Sciences in Chemistry, Biotechnology and Health, Fibre and Polymer Technology, KTH Royal Institute of Technology, Stockholm, Sweden
6 shared publications Anna Carlmark
KTH Royal Institute of Technology, School of Chemical Science and Engineering, Fibre and Polymer Technology, SE-100 44 Stockholm, Sweden
3 shared publications- Henrik Hillborg
ABB AB, Corporate Research, Power Technology, Västerås, SE-721 78, Sweden
3 shared publications Ulf W. Gedde
KTH Royal Institute of Technology, School of Chemical Science and Engineering, Fibre and Polymer Technology, SE-100 44 Stockholm, Sweden
3 shared publications- Anna Carlmark
KTH Royal Institute of Technology
2 shared publications
Latest Publications
- Open Access
Characterization of Reduced and Surface-Modified Graphene Oxide in Poly(Ethylene-co-Butyl Acrylate) Composites for Electrical Applications
Promising electrical field grading materials (FGMs) for high-voltage direct-current (HVDC) applications have been designed by dispersing reduced graphene oxide (rGO) grafted with relatively short chains of poly (n-butyl methacrylate) (PBMA) in a poly(ethylene-co-butyl acrylate) (EBA) matrix. All rGO-PBMA composites with a filler fraction above 3 vol.% exhibited a distinct non-linear resistivity with increasing electric field; and it was confirmed that the resistivity could be tailored by changing the PBMA graft length or the rGO filler fraction. A combined image analysis- and Monte-Carlo simulation strategy revealed that the addition of PBMA grafts improved the enthalpic solubility of rGO in EBA; resulting in improved particle dispersion and more controlled flake-to-flake distances. The addition of rGO and rGO-PBMAs increased the modulus of the materials up to 200% and the strain did not vary significantly as compared to that of the reference matrix for the rGO-PBMA-2 vol.% composites; indicating that the interphase between the rGO and EBA was subsequently improved. The new composites have comparable electrical properties as today’s commercial FGMs; but are lighter and less brittle due to a lower filler fraction of semi-conductive particles (3 vol.% instead of 30–40 vol.%).
Open AccessCharacterization of Reduced and Surface-Modified Graphene Oxide in Poly(Ethylene-co-Butyl Acrylate) Composites for Electrical Applications
Promising electrical field grading materials (FGMs) for high-voltage direct-current (HVDC) applications have been designed by dispersing reduced graphene oxide (rGO) grafted with relatively short chains of poly (n-butyl methacrylate) (PBMA) in a poly(ethylene-co-butyl acrylate) (EBA) matrix. All rGO-PBMA composites with a filler fraction above 3 vol.% exhibited a distinct non-linear resistivity with increasing electric field; and it was confirmed that the resistivity could be tailored by changing the PBMA graft length or the rGO filler fraction. A combined image analysis- and Monte-Carlo simulation strategy revealed that the addition of PBMA grafts improved the enthalpic solubility of rGO in EBA; resulting in improved particle dispersion and more controlled flake-to-flake distances. The addition of rGO and rGO-PBMAs increased the modulus of the materials up to 200% and the strain did not vary significantly as compared to that of the reference matrix for the rGO-PBMA-2 vol.% composites; indicating that the interphase between the rGO and EBA was subsequently improved. The new composites have comparable electrical properties as today’s commercial FGMs; but are lighter and less brittle due to a lower filler fraction of semi-conductive particles (3 vol.% instead of 30–40 vol.%).
- 10 July 2017
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 38 (16)
Reduced and Surface‐Modified Graphene Oxide with Nonlinear Resistivity
Field‐grading materials (FGMs) are used to reduce the probability for electrical breakdowns in critical regions of electrical components and are therefore of great importance. Usually, FGMs are heavily filled (40 vol.%) with semi‐conducting or conducting particles. Here, polymer‐grafted reduced graphene oxide (rGO) is used as a filler to accomplish percolated networks at very low filling ratios (co‐butyl acrylate) (EBA). Various simulation models are used to predict the percolation threshold and the flake‐to‐flake distances, to complement the experimental results. A substantial increase in thermal stability of rGO is observed after surface modification, either by silanization or subsequent polymerizations. The non‐linear DC resistivity of neat and silanized rGO and its trapping of charge‐carriers in semi‐crystalline EBA are demonstrated for the first time. It is shown that the polymer‐grafted rGO improve the dispersibility in the EBA‐matrix and that the graft length controls the inter‐flake distances (i.e. charge‐carrier hopping distances). By the appropriate selection of graft lengths, both highly resistive materials at 10 kV mm‐1 and FGMs with a large and distinct drop in resistivity (six decades) are obtained, followed by saturation. The nonlinear drop in resistivity is attributed to narrow inter‐flake distance distributions of grafted rGO.
- 10 July 2017
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 38 (16)
Reduced and Surface‐Modified Graphene Oxide with Nonlinear Resistivity
Field‐grading materials (FGMs) are used to reduce the probability for electrical breakdowns in critical regions of electrical components and are therefore of great importance. Usually, FGMs are heavily filled (40 vol.%) with semi‐conducting or conducting particles. Here, polymer‐grafted reduced graphene oxide (rGO) is used as a filler to accomplish percolated networks at very low filling ratios (co‐butyl acrylate) (EBA). Various simulation models are used to predict the percolation threshold and the flake‐to‐flake distances, to complement the experimental results. A substantial increase in thermal stability of rGO is observed after surface modification, either by silanization or subsequent polymerizations. The non‐linear DC resistivity of neat and silanized rGO and its trapping of charge‐carriers in semi‐crystalline EBA are demonstrated for the first time. It is shown that the polymer‐grafted rGO improve the dispersibility in the EBA‐matrix and that the graft length controls the inter‐flake distances (i.e. charge‐carrier hopping distances). By the appropriate selection of graft lengths, both highly resistive materials at 10 kV mm‐1 and FGMs with a large and distinct drop in resistivity (six decades) are obtained, followed by saturation. The nonlinear drop in resistivity is attributed to narrow inter‐flake distance distributions of grafted rGO.
- Open Access
- 2 June 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 5 (27) , 14241-14258
Tailoring dielectric properties using designed polymer-grafted ZnO nanoparticles in silicone rubber
Polymer grafts were used to tailor the interphases between ZnO nanoparticles (NPs) and silicone matrices. The final electrical properties of the nanocomposites were tuned by the grafted interphases, by controlling the inter-particle distance and the NP-morphology. The nanocomposites can be used in electrical applications where control of the resistivity is desired. Hansen's solubility parameters were used to select a semi-compatible polymer for grafting to obtain anisotropic NP morphologies in silicone, and the grafted NPs self-assembled into various morphologies inside the silicone matrices. The morphologies in the semi-compatible nanocomposites could be tuned by steering the graft length of poly(n-butyl methacrylate) via entropic matrix-graft wetting using surface-initiated atom-transfer radical polymerization. Image analysis models were developed to calculate the radius of primary NPs, the fraction of aggregates, the dispersion, and the face-to-face distance of NPs. The dielectric properties of the nanocomposites were related to the morphology and the face-to-face distance of the NPs. The dielectric losses, above 100 Hz, for nanocomposites with grafted NPs were approximately one decade lower than those of pristine NPs. The isotropic nanocomposites increased the resistivity up to 100 times compared to that of neat silicone rubber, due to the trapping of charge carriers by the interphase of dispersed NPs and nanoclusters. On the other hand, the resistivity of anisotropic nanocomposites decreased 10–100 times when the inter-particle distance in continuous agglomerates was close to the hopping distance of charge carriers. The electrical breakdown strength increased for compatible isotropic nanocomposites, and the temperature dependence of the resistivity and the activation energy were ∼50% lower in the nanocomposites with grafted NPs. These flexible dielectric nanocomposites are promising candidates for low-loss high-voltage transmission cable accessories, mobile electronic devices, wearables and sensors.
- 2 June 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 5 (27) , 14241-14258
Open AccessTailoring dielectric properties using designed polymer-grafted ZnO nanoparticles in silicone rubber
Polymer grafts were used to tailor the interphases between ZnO nanoparticles (NPs) and silicone matrices. The final electrical properties of the nanocomposites were tuned by the grafted interphases, by controlling the inter-particle distance and the NP-morphology. The nanocomposites can be used in electrical applications where control of the resistivity is desired. Hansen's solubility parameters were used to select a semi-compatible polymer for grafting to obtain anisotropic NP morphologies in silicone, and the grafted NPs self-assembled into various morphologies inside the silicone matrices. The morphologies in the semi-compatible nanocomposites could be tuned by steering the graft length of poly(n-butyl methacrylate) via entropic matrix-graft wetting using surface-initiated atom-transfer radical polymerization. Image analysis models were developed to calculate the radius of primary NPs, the fraction of aggregates, the dispersion, and the face-to-face distance of NPs. The dielectric properties of the nanocomposites were related to the morphology and the face-to-face distance of the NPs. The dielectric losses, above 100 Hz, for nanocomposites with grafted NPs were approximately one decade lower than those of pristine NPs. The isotropic nanocomposites increased the resistivity up to 100 times compared to that of neat silicone rubber, due to the trapping of charge carriers by the interphase of dispersed NPs and nanoclusters. On the other hand, the resistivity of anisotropic nanocomposites decreased 10–100 times when the inter-particle distance in continuous agglomerates was close to the hopping distance of charge carriers. The electrical breakdown strength increased for compatible isotropic nanocomposites, and the temperature dependence of the resistivity and the activation energy were ∼50% lower in the nanocomposites with grafted NPs. These flexible dielectric nanocomposites are promising candidates for low-loss high-voltage transmission cable accessories, mobile electronic devices, wearables and sensors.
- Open Access
- 29 June 2016
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 8 (27) , 13522
Correction: Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states
Correction for ‘Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states’ by Martin Wåhlander, et al., Nanoscale, 2016, DOI: 10.1039/c6nr01502f.
- 29 June 2016
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 8 (27) , 13522
Open AccessCorrection: Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states
Correction for ‘Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states’ by Martin Wåhlander, et al., Nanoscale, 2016, DOI: 10.1039/c6nr01502f.
- Open Access
- 18 May 2016
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 8 (31) , 14730-14745
Hydrophobic matrix-free graphene-oxide composites with isotropic and nematic states
We demonstrate a novel route to synthesise hydrophobic matrix-free composites of polymer-grafted graphene oxide (GO) showing isotropic or nematic alignment and shape-memory effects. For the first time, a cationic macroinitiator (MI) has been immobilised on anionic GO and subsequently grafted with hydrophobic polymer grafts. Dense grafts of PBA, PBMA and PMMA with a wide range of average graft lengths (MW: 1–440 kDa) were polymerised by surface-initiated controlled radical precipitation polymerisation from the statistical MI. The surface modification is designed similarly to bimodal graft systems, where the cationic MI generates nanoparticle repulsion, similar to dense short grafts, while the long grafts offer miscibility in non-polar environments and cohesion. The state-of-the-art dispersions of grafted GO were in the isotropic state. Transparent and translucent matrix-free GO-composites could be melt-processed directly using only grafted GO. After processing, birefringence due to nematic alignment of grafted GO was observed as a single giant Maltese cross, 3.4 cm across. Permeability models for composites containing aligned 2D-fillers were developed, which were compared with the experimental oxygen permeability data and found to be consistent with isotropic or nematic states. The storage modulus of the matrix-free GO-composites increased with GO content (50% increase at 0.67 wt%), while the significant increases in the thermal stability (up to 130 °C) and the glass transition temperature (up to 17 °C) were dependent on graft length. The tuneable matrix-free GO-composites with rapid thermo-responsive shape-memory effects are promising candidates for a vast range of applications, especially selective membranes and sensors.
- 18 May 2016
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 8 (31) , 14730-14745
Open AccessHydrophobic matrix-free graphene-oxide composites with isotropic and nematic states
We demonstrate a novel route to synthesise hydrophobic matrix-free composites of polymer-grafted graphene oxide (GO) showing isotropic or nematic alignment and shape-memory effects. For the first time, a cationic macroinitiator (MI) has been immobilised on anionic GO and subsequently grafted with hydrophobic polymer grafts. Dense grafts of PBA, PBMA and PMMA with a wide range of average graft lengths (MW: 1–440 kDa) were polymerised by surface-initiated controlled radical precipitation polymerisation from the statistical MI. The surface modification is designed similarly to bimodal graft systems, where the cationic MI generates nanoparticle repulsion, similar to dense short grafts, while the long grafts offer miscibility in non-polar environments and cohesion. The state-of-the-art dispersions of grafted GO were in the isotropic state. Transparent and translucent matrix-free GO-composites could be melt-processed directly using only grafted GO. After processing, birefringence due to nematic alignment of grafted GO was observed as a single giant Maltese cross, 3.4 cm across. Permeability models for composites containing aligned 2D-fillers were developed, which were compared with the experimental oxygen permeability data and found to be consistent with isotropic or nematic states. The storage modulus of the matrix-free GO-composites increased with GO content (50% increase at 0.67 wt%), while the significant increases in the thermal stability (up to 130 °C) and the glass transition temperature (up to 17 °C) were dependent on graft length. The tuneable matrix-free GO-composites with rapid thermo-responsive shape-memory effects are promising candidates for a vast range of applications, especially selective membranes and sensors.
- 1 December 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 22 (6) , 3107-3117
Dielectric and physico-chemical properties of epoxy-mica insulation during thermoelectric aging
Three stator bars were subjected to 1142 hours of thermoelectric aging. At intervals during this time, the aging of the insulation was investigated by capacitance (C) and dissipation factor (DF) measurements and by the physicochemical techniques of infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). Results indicated different degradation paths under discharge conditions, where the volume of voids within the insulation played a major role. Postcuring reactions were predominant during the first aging cycles. Such reactions were detected as reductions in capacitance and dissipation factor parameters, as a depletion of the chemical group epoxide at the absorption band 909 cm-1 as measured by FTIR, and as an increase of the glass transition temperature (Tg) of the epoxy resin. Since the postcuring reactions occur globally in the insulation, they were detected by both dielectric and physicochemical techniques. With the advance of the aging program the epoxy resin underwent structural changes, seen as modifications of functional groups CH2, CH3 and C=O. The air atmosphere where partial discharges occurred also promoted the formation of reactive species. When the air volume was high enough, the findings of FTIR measurements suggested a local degradation mechanism of mica involving cation exchange reactions between partial discharge byproducts and potassium layers in the mica.
- 1 December 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 22 (6) , 3107-3117
Dielectric and physico-chemical properties of epoxy-mica insulation during thermoelectric aging
Three stator bars were subjected to 1142 hours of thermoelectric aging. At intervals during this time, the aging of the insulation was investigated by capacitance (C) and dissipation factor (DF) measurements and by the physicochemical techniques of infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). Results indicated different degradation paths under discharge conditions, where the volume of voids within the insulation played a major role. Postcuring reactions were predominant during the first aging cycles. Such reactions were detected as reductions in capacitance and dissipation factor parameters, as a depletion of the chemical group epoxide at the absorption band 909 cm-1 as measured by FTIR, and as an increase of the glass transition temperature (Tg) of the epoxy resin. Since the postcuring reactions occur globally in the insulation, they were detected by both dielectric and physicochemical techniques. With the advance of the aging program the epoxy resin underwent structural changes, seen as modifications of functional groups CH2, CH3 and C=O. The air atmosphere where partial discharges occurred also promoted the formation of reactive species. When the air volume was high enough, the findings of FTIR measurements suggested a local degradation mechanism of mica involving cation exchange reactions between partial discharge byproducts and potassium layers in the mica.
- 13 November 2015
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 7 (46) , 25669-25678
Novel Nanocomposites of Poly(lauryl methacrylate)-Grafted Al2O3 Nanoparticles in LDPE
Aluminum oxide nanoparticles (NPs) were surface-modified by poly(lauryl methacrylate) (PLMA) using surface-initiated atom-transfer radical polymerization (SI-ATRP) of lauryl methacrylate. Nanocomposites were obtained by mixing the grafted NPs in a low-density polyethylene (LDPE) matrix in different ratios. First, the NPs were silanized with different aminosilanes, (3-aminopropyl)triethoxysilane, and 3-aminopropyl(diethoxy)methylsilane (APDMS). Subsequently, α-BiB, an initiator for SI-ATRP, was attached to the amino groups, showing higher immobilization ratios for APDMS and confirming that fewer self-condensation reactions between silanes took place. In a third step SI-ATRP of LMA at different times was performed to render PLMA-grafted NPs (NP-PLMAs), showing good control of the polymerization. Reactions were conducted for 20 to 60 min, obtaining a range of molecular weights between 23 000 and 83 000 g/mol, as confirmed by size-exclusion chromoatography of the cleaved grafts. Nanocomposites of NP-PLMAs at ...
- 13 November 2015
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 7 (46) , 25669-25678
Novel Nanocomposites of Poly(lauryl methacrylate)-Grafted Al2O3 Nanoparticles in LDPE
Aluminum oxide nanoparticles (NPs) were surface-modified by poly(lauryl methacrylate) (PLMA) using surface-initiated atom-transfer radical polymerization (SI-ATRP) of lauryl methacrylate. Nanocomposites were obtained by mixing the grafted NPs in a low-density polyethylene (LDPE) matrix in different ratios. First, the NPs were silanized with different aminosilanes, (3-aminopropyl)triethoxysilane, and 3-aminopropyl(diethoxy)methylsilane (APDMS). Subsequently, α-BiB, an initiator for SI-ATRP, was attached to the amino groups, showing higher immobilization ratios for APDMS and confirming that fewer self-condensation reactions between silanes took place. In a third step SI-ATRP of LMA at different times was performed to render PLMA-grafted NPs (NP-PLMAs), showing good control of the polymerization. Reactions were conducted for 20 to 60 min, obtaining a range of molecular weights between 23 000 and 83 000 g/mol, as confirmed by size-exclusion chromoatography of the cleaved grafts. Nanocomposites of NP-PLMAs at ...
- 1 June 2015
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 448, 482-491
Superhydrophobicity: Cavity growth and wetting transition
- 1 June 2015
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 448, 482-491
Superhydrophobicity: Cavity growth and wetting transition