SPSerhii Oleksandrovich Plitchenko

Serhii Oleksandrovich Plitchenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Serhii Oleksandrovich Plitchenko has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • INFLUENCE OF DYNAMIC STRAIN AGING ON THE PROPERTIES OF COLD-DRAWN CARBON STEEL

    by Ihor Vakulenko, Serhii Plitchenko, Tatyana Kalinina

    For cold-drawn carbon steels, the regularities governing the influence of alternating deformation and temperature on the development of dynamic strain aging (DSA) processes have been established. It was found that a change in the deformation sign (compression-tension) leads to a shift in the onset of the first flow stress serrations toward higher strain levels. Based on the analysis of a stress unrevised motion of dislocation and coefficient of strain hardening, it is shown that the suppression of DSA during reverse loading is caused by a disruption in the kinetic relationship between the dislocation waiting time (for interaction with solute atoms) and the duration of their free motion. It has been established that applying alternating bending within the temperature range of 250—275 °C achieves a plasticization effect in high-carbon wire without compromising its strength properties. The results are explained by dislocation recombination processes and changes in the conditions of their pinning by impurity atom atmospheres. The necessity of forced cooling of the metal after deformation is justified to prevent the development of static strain aging (SSA) in coils, thereby preserving the positive effect of increased ductility.

  • FEATURES OF DYNAMIC STRAIN AGING DEVELOPMENT IN CARBON STEEL DURING REVERSE LOADING

    by S.O. Plitchenko, I.O. Vakulenko, T.V. Kalinina

    The study evaluates the possibility of increasing the ductility of cold-drawn carbon steel by utilizing controlled dynamic strain aging (DSA) processes under alternating deformation. It was found that a change in the deformation sign (compression-tension) leads to a shift in the onset of flow stress serrations toward higher strain levels compared to unidirectional tension. Based on the analysis of the stress of unrevised motion of dislocations and the strain hardening coefficient, it is shown that the suppression of DSA during reverse loading is caused by a disruption in the kinetic relationship between the dislocation waiting time and the duration of their free motion. An optimal temperature range for alternating bending (250–275 °C) was identified, which ensures the realization of kinetic conditions for stabilizing DSA processes to enhance the plasticity of high-carbon wire without compromising its strength properties. It is proved that heating above 275 °C violates this condition, leading to the degradation of mechanical properties. The practical value lies in justifying the necessity of forced cooling of the metal after deformation.

  • Open Access

    EFFECT OF AUSTENITE DEGRADATION CONDITIONS ON THE PROPERTIES OF STEEL 20

    by Ihor Vakulenko, Serhii Plitchenko, Tatyana Kalinina

    Purpose. To investigate the nature of property changes in thermally strengthened coiled steel 20 depending on the mechanism of austenite degradation. Research methods. The material for study was a wire with a diameter of 3 mm, made of low-carbon steel, with 0.22 % С, 0.46 % Mn, 0.088 % Si, 0.1 % Cr, 0.03 % S, 0.012 % P. The different structure state of the steel was obtained after certain processing. The samples, 0.3 m long, were subjected to austenitization at a temperature of 920 °C for 8 min, after that for 10 min followed isotherm exposure, at temperatures of 650–200 °C and tempering at temperature of isothermal transformation, duration by 60 min. The microstructure was studied using light and electron microscopy. Dimensions of structural element were determined by quantitative metallography methods. The mechanical properties were determined from analyzing tensile curves at room temperature and strain rate of 10-3 s-1. Results. The change at structure and properties is largely determined by the mechanism of austenite transformation under isothermal conditions. During diffusion transformation of austenite, the dispersion of the phase components is accompanied by an increase at super saturation of the solid solution by carbon. For the intermediate transformation region, a change at phase composition of the steel is added. The subsequent tempering determines the kinetics and degree of completion processes of structure formation of the thermally hardened rolled steel. At low tempering temperatures of steel with a bainite structure, hardening is due to the development of aging processes. With an increase at tempering temperature, the development of softening processes is accelerated. Scientific novelty. The increase plasticity of the steel with a bainite structure is due to a decrease of dispersion of cementite particles, dislocation density, and the development of polygonization at initial stages of recrystallization. The softening of steel with a ferrite-pearlite structure is determined by a decrease in phase hardening during austenite transformation. Practical value. Mechanism analysis of structural transformations has determined that manufacture of thermally strengthened rolled steel, the expected softening after coiling is recommended to compensate by a corresponding decrease of temperature of the end of accelerated cooling.

  • Open Access

    The Effect of Stress Pulses on the Limited Endurance Under Cyclic Loading of Thermal-Hardened Carbon Steel

    by I. O. Vakulenko, S. O. Plitchenko, K. Yu. Shevelieva

    Purpose. The assess effect of stress pulses on the cyclic endurance of thermal-hardened carbon steel. Methodology. A sheet with a thickness of 1 mm was selected for the study, made of steel with 0.42% С after thermal hardening. The treatment consisted of quenching and tempering at 300 °С. The samples were subjected to cyclic loading on the Saturn-10 machine, under a symmetrical cycle of alternating bending, with a frequency of 100 min-1. Treatment with pulses of stress was carried out under conditions of «Iskra–23». To determine the effect pulses of stress on the cyclic endurance, samples after 50–60% by limit of endurance were subjected to doing pulses of stress. After completion treatment pulse of stress, the samples continued to be cyclically loaded until the moment of failure. The density of dislocations was measured by method of X-ray structural analysis on a DRON-3 diffractometer, by interferences (110), (211), (321). The complex of properties after thermal strengthening was determined under static tension, at a strain rate of 10-3 s-1. Findings. After processing with pulses of stress studied, thermally hardened steel with a hardness of 46–47 HRC, an increase in hardness by 11 % was obtained. According to the analysis of the cyclic loading curves of thermally hardened carbon steel, it was determined that due to the action pulses of stress, an increase in limit of endurance occurs in a wide range of cyclic overload. Structural studies have determined that, in proportion to decrease at magnitude of cyclic overload, an increase limit of endurance corresponds to higher number accumulated dislocations by different slip systems. Originality. The increase at density of dislocations from the action pulses of stress is due to the development processes of partial unlocking of dislocations after thermal strengthening and activation systems of sliding, which are not characteristic of these loading conditions of the steels. As a result of the action pulses of stress, the propagation deformation per cycle occurs at lower amplitudes of load, due to formation of an additional number of dislocations. According to analysis lines of French, it was determined that participation of an increased number of dislocations at propagation of deformation per cycle shifts a moment transformation of reversible damages into irreversible ones, towards an increase at number of cycles. Practical value. The obtained research results can be useful for assessing by influence of an external source of stress on the behavior of a carbon steel product under cyclic loading.

  • Open Access

    Influence Degree and Scheme of Hot Reduction on Properties of the Carbon Steel

    by Igor Alex Vakulenko, Serhii Oleksandrovich Plitchenko, Ahmet Fatih Yılmaz

    This study examines the impact of hot plastic deformation at 1250°C on austenite grain refinement and mechanical properties in carbon steel for railway wheels. The deformation strategies—single-step versus two-step compression with equivalent total strain—were compared to assess their effects on austenitic microstructure and material performance. Austenite grain size was quantified via light microscopy and quantitative structural analysis, while mechanical properties were evaluated using a universal tensile testing machine, following the ASTM E8 standard, at room temperature. (strain rate: 10⁻³ s⁻¹) Results reveal that austenite grain refinement occurs proportionally with increasing deformation, irrespective of the compression scheme. However, the deformation strategy significantly influences strength and ductility at lower strain levels. Specifically, two-stage compression at smaller strains (e.g., below 60% total deformation) enhances ultimate tensile strength by up to 10% and ductility by 30–40% compared to single-step compression. This improvement is attributed to partial retention of austenite substructure during interrupted deformation, which alters dynamic recrystallization kinetics and promotes dislocation redistribution. The differential effect diminishes progressively with higher strain levels, and beyond 60% deformation, both schemes yield equivalent grain sizes and mechanical properties due to complete recrystallization and microstructural homogenization. These findings underscore the critical role of deformation sequencing in optimizing mechanical performance during thermomechanical processing, particularly for applications requiring tailored strength-ductility balances in high-temperature-formed carbon steels.

  • Determination of the causes of rolling surface damage during operation of the railway wheels

    by I. O Vakulenko, S. O Plitchenko, A. F Yilmaz

    Purpose. Substantiation of the mechanism of damage formation on the rolling surface of railway wheels by different strength levels to determine optimal structural state of the carbon steel. Methodology. The material for study was steel from rim fragments of the railway wheels with a carbon concentration of 0.61 and 0.69 % and other chemical elements within the range of the grade composition. Samples for mechanical tests were subjected to thermal hardening to obtain different structural states. The microstructure was examined under light and electron microscopes, using quantitative metallography techniques. Metal wear was determined under dry friction conditions, with different degrees of slippage, on a machine of the SMC-2 type. Hardness was estimated by the Rockwell method, and micro hardness of structural components – on a PMT-3 micro hardness tester. Findings. Based on the analysis of the wheel-rail interaction, it was determined that resulting inhomogeneity at distribution of plastic deformation and heating temperature in the plane of the contact surface are due to the development of slippage processes. Heating the metal to temperatures higher than onset of phase transformations and subsequent accelerated cooling determine the mechanism of structural transformations. The difference between adjacent sections of the rolling surface with different structural states and corresponding level of strength determines conditions for the formation of a fracture center of the railway wheel during operation. Originality. Heating the metal to temperatures above onset of phase transformations from the wheel sliding along rail and subsequent forced cooling is the cause of formation of gradient of the structures from pearlite to martensitic-bainite. The cyclic nature of the change in the structural state of the metal from simultaneous influence elevated temperatures, high plastic deformations and phase transformations corresponds to the development of low-cycle fatigue processes. Plastic deformation of the rolling surface area with martensitic or bainite structures is accompanied by softening, and with pearlite structures – by a hardening process. Practical value. The obtained results of the development of phase transformations in carbon steel on rolling surface will be useful in determining optimal structural state of the railway wheels of different strength levels.

  • STRUCTURAL CHANGES DURING THERMAL STRENGTHENING OF THE RAILWAY WHEEL

    by I. Vakulenko, S. Plitchenko, S. Gubarev, A. Khlebnikov

    Purpose. Justification of mechanism of the structure transformations in the carbon steel of the railway wheel during disk thermal strengthening. Research methods. The material for the study was carbon steel of a railway wheel with a content of 0.57 % C, 0.65 % Si, 0.45 % Mn, 0.0029 % S, 0.014 % P and 0.11 % Cr. The railway wheel was heated to temperatures higher than Ac3, kept at this temperature to complete austenite homogenization process, and disk was rapidly cooled to the specified temperature. Degree defectiveness structure of the metal after accelerated cooling was assessed using technique of X-ray structural analysis. Strength stress, yield stress and relative elongation of the carbon steel were determined at stretching at rate of deformation 10-3 s-1. Results. At accelerated cooling of the carbon steel, the sources of strengthening are the processes of blocking mobile dislocations due to the condensation of carbon atoms on them and dispersion strengthening from the formed particles of the carbide phase. At temperatures of termination of forced cooling of carbon steel above 300…350 °C, the reduction rate of strength properties is determined by the excess of total effect of softening from decomposition of the solid solution, acceleration of spheroidization and coalescence of cementite particles over the blocking of dislocations by carbon atoms and dispersion hardening. Scientific novelty. The level of strength and plasticity characteristics of carbon steel of the railway wheel disc, depending on the temperature end forced cooling, is determined by the ratio of the influence of degree super saturation of the solid solution and the dispersion strengthening by carbide phase. Practical value. For temperatures termination of accelerated cooling of 200…300 °C, degree of super saturation of the solid solution is the main factor that determines the level of strength and plasticity characteristics. When manufacturing an all-rolled railway wheel, the strength limit of the disc metal can be increased by accelerated cooling to the middle range of temperature.

  • Open Access

    Influence of the Isothermal Transformation Temperature on the Structure and Properties of Low-Carbon Steel

    by I. A. Vakulenko, S. O. Plitchenko, K. Asgarov, B. V. Lytvynov, A. Orak, H. Umur

    Purpose. The study is aimed at evaluating the effect of the isothermal transformation temperature on the structure and properties of low-carbon steel. Methodology. The material for the study was a 3 mm diameter wire made of mild steel with the following chemical composition: 0.21% C, 0.47% Mn, 1.2% Si, 0.1% Cr, 0.03% S, 0.012% P. The 0.3 m long wire samples were subjected to austenitizing at 920 °C for 8...9 min, after which they were held isothermally for 11 min at temperatures of 650...200 °C, followed by cooling in air. The strength, plastic properties, and strain hardening coefficient were determined from the analysis of tensile curves. Findings. It was found that a decrease in the temperature of isothermal transformation, starting from 450...400 °C, increases the amount of Widmannstätten ferrite due to the disappearance of polyhedral ferrite grains. At the same time, the number of areas with locally located dispersed cementite particles similar to pearlite colonies increases, and bainite crystals appear. Against the background of a sharp decrease in the strain hardening coefficient in the range of 450...400 °C, the ability of the bainite phase to undergo plastic deformation should be considered one of the reasons for the delay in density reduction. Originality. The effect of steel hardening with a decrease in the pearlite transformation temperature is based on the grinding of ferrite grains, an increase in the amount of Widmannstätten ferrite, and the dispersion of pearlite colonies. The strengthening effect of steel with a bainite structure is based on an increase in the degree of supersaturation of the solid solution with carbon atoms and dispersion hardening by particles of the carbide phase. Practical value. The optimal structural state of steel intended for the manufacture of such critical elements as a support beam, railroad car bogie, etc. is a mixture of phase components with different dispersion and morphology, and their quantitative ratio is determined by the operating conditions of a particular product.


  • Open Access

    PHENOMENON OF THE SOFTENING COLD-DEFORMED LOW-CARBON STEEL DURING ALTERNATING BENDING

    by Ihor Vakulenko, Volodymyr Sukhomlyn, Serhii Plitchenko, Dal Serkan, Illia Gurin, І.о. Вакуленко, В.і. Сухомлин, С.о. Плітченко, І.в. Гурін

    For cold-rolled low-carbon steel, detected softening during alternating bending is accompanied by an increase in ductility and ability to strain hardening. The softening process is accompanied by a change at morphology of ferrite grains. Elongated grains after cold rolling acquire a shape close to a polyhedron after alternating bending. Compared to the strength properties, for which a maximum decrease corresponds to four bending cycles, the ductility and strain hardening ability of the metal continue to increase even after eight cycles. The non-monotonic nature of change in dislocation density depending on the number of bending cycles indicates complex substructural changes in cold-rolled metal, which has a dislocation cellular structure varying degrees of the perfection.

  • Open Access

    FEATURES OF WEAR AND PROSPECTS FOR RESTORATION OF THE WORM AUGER SEGMENT OF A BEAD MILL

    by Valerii Herasimov, Serhii Plitchenko, Valerii Peremitko, Illia Matyazh

    One of the most common problems of bead mills is the intensive wear of their working grinding segments, which negatively affects the quality of the crushed material and causes long-term downtime of the equipment, and, as a result, economic losses. Taking into account the identified problem, the purpose of the study is to analyze the working conditions and the nature of wear of the working surfaces of the segments of the bead worm shaft and justify the technology of their restoration. It was established that the main wear of the contact surfaces of the cast iron segments (ChKh1) is caused by their friction with the beads, which according to their chemical composition (55 % SiO2, 19.3 % СaO, 13.4 % Al2O3, 6.5 % B2O3, 4.2 % MgO) and hardness are an abrasive element relative to wearing surfaces. The nature and degree of loss of size and shape of the segments due to wear depends, among other things, on the diameter of the bead balls, which determines the waviness of the contact surface of the segment and the gradient of hardness values due to defamation. On the other hand, the working surfaces are affected by the technological suspension, which causes the appearance of the effect of cavitation wear, which consists in the formation of indentations on the surface after multiple repeated blows of the liquid. The conducted analysis of the operating conditions of the segments established a combined hydroabrasive wear mechanism of their working surfaces, which is explained by the simultaneous effect of abrasive bead elements and technological suspension. The nature of the intensity of the mentioned wear mechanism is uneven along the height of the worm screw, from mainly hydroabrasive for the upper segments to almost purely abrasive for the lower segments. Taking into account the determined mechanism of wear, it is proposed to restore the working surfaces of the segments by electric arc surfacing, and powder-coated wires of different chemical composition are used as surfacing materials. To clarify the influence of the chemical composition of the deposited metal on the mechanical properties of the restored layer, it is proposed to use powder-coated wires with different contents, primarily of carbon and chromium, which will allow to evaluate the resistance of the contact surfaces to both abrasive and hydroabrasive wear. Під час роботи бісерного млина типу МТ-140 виявлено інтенсивне зношування молольних сегментів черв'ячного шнека, яке призводить до зниження ступеня подрібнення сировини, викликає тривалий простій обладнання та, як наслідок, економічні втрати. Проведений аналіз умов роботи сегментів встановив комбінований гідроабразивний механізм зносу їх робочих поверхонь, який пояснюється одночасним впливом абразивних бісерних елементів та технологічної суспензії. Характер інтенсивності наведеного механізму зносу є нерівномірним по висоті черв'ячного шнека, від переважно гідроабразивного для верхніх сегментів і до майже чисто абразивного для розміщених нижче. Зважаючи на визначений механізм зносу, запропоновано відновлювати робочі поверхні сегментів електродуговим наплавленням, а в якості наплавних матеріалів – порошкові дроти різного хімічного складу. Для його уточнення запропоновано використовувати склади шихти з різним вмістом вуглецю та хрому.