EMEdson Irineu Muller

Edson Irineu Muller

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Edson Irineu Muller has a total of 270 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Clean Production of Sugars from Brewer’s Spent Grains Using Subcritical Water Hydrolysis and Steam Explosion

    by Lucielle Ferreira Nunes, Gustavo Andrade Ugalde, Kéllen Francine Anschau, Edson Irineu Müller, Marcus Vinícius Tres, Giovani Leone Zabot, Raquel Cristine Kuhn

    Brewer’s spent grains (BSG) are a by-product of the beer industry and can be used to produce biofuels. In this case, the objective of this study was to obtain reducing sugars from this biomass by subcritical water hydrolysis in a semi-continuous mode after steam explosion. Temperatures of 120–180 °C, reaction times of 1–5 min, and pressures of 15–25 MPa were used for the steam explosion without CO2. Moistures of 10–50% (w/v), temperatures of 120–180 °C, reaction times of 1–5 min, and pressures of 15–25 MPa were used for the steam explosion with CO2. Subcritical water hydrolysis of solid-exploded material was developed at 210 °C, 15 MPa, a solid/feed ratio of 16 g/g, and a flow rate of 20 mL/min. The characterization of BSG, reducing sugar yields, kinetic profiles, the composition of monosaccharides and furanic moieties, and the characterization of remaining solid by Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) were performed. For steam explosion with CO2, the significant variables were the temperature and moisture, and the optimized conditions were moisture of 50% (w/v), 120 °C, pretreatment for 1 min, and 15 MPa, with a reducing sugars yield of 18.41 ± 1.02 g/100 g BSG. For steam explosion without CO2, the significant variables were the time and temperature, and the optimized conditions were 120 °C, pretreatment for 1 min, and 15 MPa, with a reducing sugars yield of 17.05 ± 0.48 g/100 g BSG. The process was successful because the steam explosion ruptured the lignocellulosic matrix, and the subsequent process of subcritical water hydrolysis could dissociate the polymers into low-chain saccharides.


  • Production, characterization and stabiliity of liposomes containing creatine

    by Rafael Pereira, Katianne Wolf Krawczak, Edson Ireneu Muller, Afonso Gabriel Inquelmann Pinto, Marta Maria Medeiros Frescura Duarte, Cristiano Rodrigo Bohn Rhoden, Luciana Maria Fontanari Krause, Sergio Roberto Mortari

    Creatine is a compound of three amino acids that is widely used as an ergogenic resource in sports, because it has the ability to form Creatine Phosphate (PCr) in the mitochondria and increase ATP resynthesis. Liposomes are nanoscale lipid vesicles used to increase the stability, viability and bioavailability of molecules such as drugs. In this work, creatine-containing liposomes were obtained by the ethanol injection method, producing liposomes with an average diameter of 124.5 nm, a polydispersity index of 0.141, and a zeta potential of -3.9 mV. Stability studies showed that the creatine-containing liposomes are stable for up to 90 days when stored at room temperature (± 25 ºC).

  • Determination of basic nitrogen content in diesel oil: A miniaturized method by digital image-based colorimetry in a portable device

    by Gabrielle Iop, Alice Holkem, Andres de Souza, Edson Muller, Juliano Barin, Paola Mello

    A miniaturized method using a portable device with digital image acquisition and PhotoMetrix PRO app data treatment was developed for the determination of basic nitrogen content in diesel oil. The method was based on the colorimetric titration described in the UOP 269-10 standard protocol. A homemade 3D-printed chamber with controlled light intensity equipped with an USB camera was used for image acquisition after an acid-base titration reaction, carried out in a miniaturized device. After mixing reagents and diesel oil, the images were obtained and converted into RGB (red, green, and blue) histograms, and a partial least squares (PLS) multivariate calibration model was constructed. Parameters of the regression model were evaluated, by the coefficient of determination (R2), the root mean squared error of calibration (RMSEC), the root mean squared error of cross-validation (RMSECV), and the root mean squared error of prediction (RMSEP). Some conditions for the acid-base titration were optimized, such as the concentration of the indicator (68.0 to 272 µmol L-1) and the titrating (HClO4, 0.179 to 1.79 mmol L-1), as well as the volume of diesel oil. With 60 µL of 2.54 mmol L-1 indicator solution, 20 µL of 20 mmol L-1 HClO4 as titrating and using 50 to 1000 µL of diesel oil, optimal conditions were obtained for calibration (RMSEP of 0.377 mg kg-1, RMSECV of 0.307 mg kg-1 with 4 factors). It is important to mention that no differences were observed (p < 0.05) when comparing reference values with the results by the proposed protocol. This proved to be advantageous in relation to the methods described in the UOP 269-10 standard since it was possible to reduce the consumption of reagents and waste generation, in agreement with green analytical chemistry. In addition, this alternative protocol combines simplicity and speed to obtain results with good accuracy, precision and suitable limit of quantification (1 mg kg-1) using a miniaturized system.


  • Rheological, permanent deformation and fatigue analysis for calibration of the recovery process of bitumens in the rotary evaporator

    by Pedro Orlando Borges de Almeida Júnior, Silvio Lisboa Schuster, Cléber Faccin, Pablo Menezes Vestena, Pedro Schmidt Ilha, Gustavo Menegusso Pires, Edson Irineu Müller, Deividi da Silva Pereira, Luciano Pivoto Specht


  • Tempering time and air temperature relationships for real-scale paddy drying and their effects on the physical, physicochemical, and morphological qualities of polished rice

    by Andressa Fernandes Leal, Paulo Carteri Coradi, Rosana dos Santos Moraes, Edson Müller, Paulo Eduardo Teodoro, Larissa Pereira Ribeiro Teodoro, Dágila Melo Rodrigues

    Tempering-drying time may affect the quality of polished rice. Hence, this study aims to evaluate the effect of drying-tempering time and air temperature relationships on the physical, physicochemical, and morphological qualities of polished rice. Herein, paddy with 20–24% (w.b.) moisture were subjected to drying and tempering with air temperatures of 75–115 °C, 115–130 °C, and 75–130 °C over 14 h to reduce their moisture content up to 12% (w.b.). With the increase in the paddy mass temperature to 49 °C, the whole grain yield and the percentages of protein, crude fiber, fat, and ash reduced; additionally, the morphology of starch and the composition of minerals were altered. The cumulative effects and prolonged time of the drying-tempering influenced the physical, physicochemical, and morphological qualities of the rice. In conclusion, paddy drying technologies with tempering periods should not be designed for temperatures not exceeding 75 °C and drying times not longer than 8 h for good system performance and rice quality.


  • Open Access

    Efficient Uptake of Angiotensin-Converting Enzyme II Inhibitor Employing Graphene Oxide-Based Magnetic Nanoadsorbents

    by Miguel Pereira de Oliveira, Carlos Schnorr, Theodoro da Rosa Salles, Franciele da Silva Bruckmann, Luiza Baumann, Edson Irineu Muller, Wagner Jesus da Silva Garcia, Artur Harres de Oliveira, Luis F. O. Silva, Cristiano Rodrigo Bohn Rhoden

    This paper reports a high efficiency uptake of captopril (CPT), employing magnetic graphene oxide (MGO) as the adsorbent. The graphene oxide (GO) was produced through an oxidation and exfoliation method, and the magnetization technique by the co-precipitation method. The nanomaterials were characterized by FTIR, XRD, SEM, Raman, and VSM analysis. The optimal condition was reached by employing GO·Fe3O4 at pH 3.0 (50 mg of adsorbent and 50 mg L−1 of CPT), presenting values of removal percentage and maximum adsorption capacity of 99.43% and 100.41 mg g−1, respectively. The CPT adsorption was dependent on adsorbent dosage, initial concentration of adsorbate, pH, and ionic strength. Sips and Elovich models showed the best adjustment for experimental data, suggesting that adsorption occurs in a heterogeneous surface. Thermodynamic parameters reveal a favorable, exothermic, involving a chemisorption process. The magnetic carbon nanomaterial exhibited a high efficiency after five adsorption/desorption cycles. Finally, the GO·Fe3O4 showed an excellent performance in CPT removal, allowing future application in waste management.


  • Open Access

    Highly Efficient Adsorption of Tetracycline Using Chitosan-Based Magnetic Adsorbent

    by Franciele da Silva Bruckmann, Carlos Eduardo Schnorr, Theodoro da Rosa Salles, Franciane Batista Nunes, Luiza Baumann, Edson Irineu Müller, Luis F. O. Silva, Guilherme L. Dotto, Cristiano Rodrigo Bohn Rhoden

    Herein, tetracycline adsorption employing magnetic chitosan (CS·Fe3O4) as the adsorbent is reported. The magnetic adsorbent was synthesized by the co-precipitation method and characterized through FTIR, XRD, SEM, and VSM analyses. The experimental data showed that the highest maximum adsorption capacity was reached at pH 7.0 (211.21 mg g−1). The efficiency of the magnetic adsorbent in tetracycline removal was dependent on the pH, initial concentration of adsorbate, and the adsorbent dosage. Additionally, the ionic strength showed a significant effect on the process. The equilibrium and kinetics studies demonstrate that Sips and Elovich models showed the best adjustment for experimental data, suggesting that the adsorption occurs in a heterogeneous surface and predominantly by chemical mechanisms. The experimental results suggest that tetracycline adsorption is mainly governed by the hydrogen bonds and cation–π interactions due to its pH dependence as well as the enhancement in the removal efficiency with the magnetite incorporation on the chitosan surface, respectively. Thermodynamic parameters indicate a spontaneous and exothermic process. Finally, magnetic chitosan proves to be efficient in TC removal even after several adsorption/desorption cycles.


  • Stationary rice drying: Influence of initial moisture contents and impurities in the mass grains on the physicochemical and morphological rice quality

    by Marcela Trojahn Nunes, Paulo Carteri Coradi, Amanda Müller, Letícia Oliveira Carneiro, Jonatas Ibagé Steinhaus, Kellen Francine Anschau, Guilherme Coelho Souza, Edson Irineu Müller, Paulo Eduardo Teodoro, Arthur Pozzobon Dutra


  • Open Access

    Development of Green Methods for the Determination of Elemental Impurities in Commercial Pharmaceutical Tablets

    by Vitoria Hagemann Cauduro, Alessandra Schneider Henn, Rochele Sogari Picoloto, Edson Irineu Muller, Marcia Foster Mesko, Erico Marlon Moraes Flores

    In this study, two methods based on the use of diluted acids were developed: microwave-assisted wet digestion (MAWD) and microwave-assisted ultraviolet digestion (MAWD-UV). These methods are evaluated for the digestion of oral pharmaceutical drugs and further determination of elemental impurities from classes 1 (As, Cd, Hg and Pb) and 2A (Co, Ni and V) by inductively coupled plasma optical emission spectrometry (ICP-OES). Commercial drugs for the treatment of type 2 diabetes are used. No prior comminution is performed. For MAWD, the optimized conditions were 2 mol L−1 or 3 mol L−1 HNO3, 1 mL of 50% H2O2 and a 45 min or 55 min irradiation program. For MAWD-UV, the condition using 1 mol L−1 HNO3, 1.6 mL of 50% H2O2 and a 55 min irradiation program enabled the digestion of all samples. In this way, efficient methods are proposed for the digestion of commercial pharmaceutical tablets for further determination of class 1 and 2A elemental impurities (ICH Q3D guidelines).


  • Development of an eco-friendly sample preparation protocol for metal determination in food samples: an oxygen pressurized single reaction chamber using diluted nitric acid

    by Cezar A. Bizzi, Matheus F. Pedrotti, Diogo M. Betiolo, Mariele S. Nascimento, Edson I. Muller, Giancarlo Cravotto, Erico M. M. Flores

    A single reaction chamber microwave-assisted wet digestion system using O 2 as an auxiliary reagent and diluted HNO 3 for multisample digestion and metal determination.