Natalia V. Ivanova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Natalia V. Ivanova has a total of 101 co-authors. Here are the top co-authors by number of shared publications:
- Valeriy M. Pugachev
Federal Research Center of Coal and Coal Chemistry, Siberian Branch, Russian Academy of Sciences, Kemerovo, Russia
8 shared publications - Vadim G. Dodonov
Federal Research Center of Coal and Coal Chemistry, Siberian Branch, Russian Academy of Sciences, Kemerovo, Russia
6 shared publications - Dmitriy M. Russakov
Kemerovo State University
3 shared publications - Roman P. Kolmykov
Federal Research Center of Coal and Coal Chemistry, Siberian Branch, Russian Academy of Sciences, Kemerovo, Russia
3 shared publications - Anna I. Vershinina
Kemerovo State University
2 shared publications - Galina Yu. Simenyuk
Federal Research Center of Coal and Coal Chemistry, Siberian Branch, Russian Academy of Sciences, Kemorovo, Russia
2 shared publications
Latest Publications
- Open Access
- 14 July 2026
- Published by Elsevier in SSRN Electronic Journal
Free-Standing SWCNT Fiber Sensors for Dopamine Detection: Effect of Heat and Chemical Pretreatment
Novel sensors from single walled carbon nanotube (SWCNT) free-standing fibers with almost entire surface accessible to analyte were used for electrochemical investigations and analysis of dopamine. The SWCNTs were synthesized using carbon monoxide or ethanol as precursors. By assembling SWCNT bundles in the form of a fiber, we are able to avoid the interference of substrate and improve detection efficiency. We examined the influence of heat and chemical pretreatments of the electrode SWCNT material on its properties. Transmission and scanning electron microscopy, Raman spectroscopy and cyclic voltammetry were used to characterize the SWCNT fibers. The pretreated free-standing SWCNT fiber sensors exhibited necessary analytical performance for dopamine determination by anodic voltammetry, including high sensitivity, repeatability, and a low limit of detection (9 – 120 µg L⁻¹). The electrochemical oxidation of dopamine on all five types of SWCNT fibers was reversible and involved dopamine adsorption onto the SWCNT surface. The heat and chemically pretreated SWCNT fiber sensors showed a linear response over a wide concentration range (0.07–150 mg L⁻¹). The developed SWCNT sensors enable rapid determination of dopamine in real samples and are characterized by high durability and a long service life.
- 14 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFree-Standing SWCNT Fiber Sensors for Dopamine Detection: Effect of Heat and Chemical Pretreatment
Novel sensors from single walled carbon nanotube (SWCNT) free-standing fibers with almost entire surface accessible to analyte were used for electrochemical investigations and analysis of dopamine. The SWCNTs were synthesized using carbon monoxide or ethanol as precursors. By assembling SWCNT bundles in the form of a fiber, we are able to avoid the interference of substrate and improve detection efficiency. We examined the influence of heat and chemical pretreatments of the electrode SWCNT material on its properties. Transmission and scanning electron microscopy, Raman spectroscopy and cyclic voltammetry were used to characterize the SWCNT fibers. The pretreated free-standing SWCNT fiber sensors exhibited necessary analytical performance for dopamine determination by anodic voltammetry, including high sensitivity, repeatability, and a low limit of detection (9 – 120 µg L⁻¹). The electrochemical oxidation of dopamine on all five types of SWCNT fibers was reversible and involved dopamine adsorption onto the SWCNT surface. The heat and chemically pretreated SWCNT fiber sensors showed a linear response over a wide concentration range (0.07–150 mg L⁻¹). The developed SWCNT sensors enable rapid determination of dopamine in real samples and are characterized by high durability and a long service life.
- Open Access
- 1 February 2024
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2701 (1) , 012010
The influence of inlet flow asymmetry on the carotid bifurcation hemodynamics
Arterial bifurcations are known to be high-risk areas for the initiation of atherosclerosis. The appearance and growth of atherosclerotic plaques in the bifurcation of the carotid artery can result in severe consequences such as cerebrovascular accidents. The common signs of an atherogenic risk center around the surpassing critical values by certain hemodynamic indices, which are distributed over the artery wall. These indices are related to the effect of blood flow on the arterial wall, and their distribution is influenced by both the bifurcation’s geometric shape and the flow structure at its inlet. The objective of this study is to carry out a comparative analysis of hemodynamic indices in personal-specific models of carotid bifurcation with centrally symmetric and asymmetric input flows. The examined geometric models of bifurcation are based on computed angiography data obtained from the individuals free of apparent pathology. By using computational fluid dynamics within these models, the distribution of hemodynamic indices in a steady periodic flow is calculated and critical zones are determined for them. All the models are divided into two groups – those with symmetric and those with asymmetric input flows. For each model with asymmetric input flow, an alternative geometry is designed to ensure inlet flow symmetry, and comparative numerical calculations of the blood flow are carried out. The results of comparative analysis reveal that the distribution of hemodynamic indices is simpler for the group with symmetric input flow. A comparison of the averages between these two groups with symmetrical and natural asymmetric input flows indicates a 55% better result for the latter group. Furthermore, for almost all models with asymmetric input flow, their alternative models give worse hemodynamic results. Thus, hemodynamic indices in simpler models with symmetrical input flow can serve as an upper estimate for indices in models with natural asymmetric flow. A total of 89 models are included in the study.
- 1 February 2024
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2701 (1) , 012010
Open AccessThe influence of inlet flow asymmetry on the carotid bifurcation hemodynamics
Arterial bifurcations are known to be high-risk areas for the initiation of atherosclerosis. The appearance and growth of atherosclerotic plaques in the bifurcation of the carotid artery can result in severe consequences such as cerebrovascular accidents. The common signs of an atherogenic risk center around the surpassing critical values by certain hemodynamic indices, which are distributed over the artery wall. These indices are related to the effect of blood flow on the arterial wall, and their distribution is influenced by both the bifurcation’s geometric shape and the flow structure at its inlet. The objective of this study is to carry out a comparative analysis of hemodynamic indices in personal-specific models of carotid bifurcation with centrally symmetric and asymmetric input flows. The examined geometric models of bifurcation are based on computed angiography data obtained from the individuals free of apparent pathology. By using computational fluid dynamics within these models, the distribution of hemodynamic indices in a steady periodic flow is calculated and critical zones are determined for them. All the models are divided into two groups – those with symmetric and those with asymmetric input flows. For each model with asymmetric input flow, an alternative geometry is designed to ensure inlet flow symmetry, and comparative numerical calculations of the blood flow are carried out. The results of comparative analysis reveal that the distribution of hemodynamic indices is simpler for the group with symmetric input flow. A comparison of the averages between these two groups with symmetrical and natural asymmetric input flows indicates a 55% better result for the latter group. Furthermore, for almost all models with asymmetric input flow, their alternative models give worse hemodynamic results. Thus, hemodynamic indices in simpler models with symmetrical input flow can serve as an upper estimate for indices in models with natural asymmetric flow. A total of 89 models are included in the study.
- Open Access
- 30 December 2023
- Published by Kemerovo State University in Food Processing: Techniques and Technology
- Vol. 53 (4) , 824-831
Electrochemical Sensors Based on Single-Wall Carbon Nanotubes in Voltammetric Ascorbic Acid Tests
Modern highly sensitive and selective sensors are able to determine biologically active substances, which makes this direction one of the most popular areas of analytical chemistry. The study featured the electrochemical properties of new fiber materials based on single-wall carbon nanotubes with prospects of using them in the voltammetry of ascorbic acid. The authors developed a new technology to synthesize films from disordered single-wall carbon nanotubes by chemical vapor deposition. Fibers were produced from a solvent by wet-pulling of single-wall carbon nanotubes networks. Thin films of randomly oriented single-wall carbon nanotube bundles were deposited downstream of a floating aerosol CVD reactor, which included a high temperature furnace with a quartz tube. The synthesis of the single-wall carbon nanotube samples was performed at 825°C. Ethanol served as carbon source while ferrocene was used as catalyst precursor. The single-wall carbon nanotubes were collected on a nitrocellulose filter in the form of films with transmittances of 10% in the middle of the visible wavelength (550 nm). The method was optimized to involve air annealing at 300–320°C and a treatment with strong inorganic acids, i.e., HCl, HNO3 + H2SO4. The voltammetric curves recording included background electrolyte, scan rate, and preconditioning. These parameters were selected experimentally to obtain the maximal sensor response to ascorbic acid content. The anodic peak of ascorbic acid in the phosphate buffer electrolyte (pH 6.86) was observed at a potential of +0.2 V. The current and peak area of ascorbic acid oxidation depended neither on the time nor on the conditioning potential of the sensor. The linear dependences of these parameters on the concentration of ascorbic acid stayed within 50–500 μmol/L (8.8–90 mg/L) at a scan rate of 0.1 mV/s. The single-wall carbon nanotube microsensor had a length of 0.5 cm and an average width of 400 μm. Its sensitivity was two times as high as that of a disk glassy carbon electrode with a diameter of 5 mm. The experimental sensors proved effective in determining ascorbic acid in food products, pharmaceuticals, and biological fluids.
- 30 December 2023
- Published by Kemerovo State University in Food Processing: Techniques and Technology
- Vol. 53 (4) , 824-831
Open AccessElectrochemical Sensors Based on Single-Wall Carbon Nanotubes in Voltammetric Ascorbic Acid Tests
Modern highly sensitive and selective sensors are able to determine biologically active substances, which makes this direction one of the most popular areas of analytical chemistry. The study featured the electrochemical properties of new fiber materials based on single-wall carbon nanotubes with prospects of using them in the voltammetry of ascorbic acid. The authors developed a new technology to synthesize films from disordered single-wall carbon nanotubes by chemical vapor deposition. Fibers were produced from a solvent by wet-pulling of single-wall carbon nanotubes networks. Thin films of randomly oriented single-wall carbon nanotube bundles were deposited downstream of a floating aerosol CVD reactor, which included a high temperature furnace with a quartz tube. The synthesis of the single-wall carbon nanotube samples was performed at 825°C. Ethanol served as carbon source while ferrocene was used as catalyst precursor. The single-wall carbon nanotubes were collected on a nitrocellulose filter in the form of films with transmittances of 10% in the middle of the visible wavelength (550 nm). The method was optimized to involve air annealing at 300–320°C and a treatment with strong inorganic acids, i.e., HCl, HNO3 + H2SO4. The voltammetric curves recording included background electrolyte, scan rate, and preconditioning. These parameters were selected experimentally to obtain the maximal sensor response to ascorbic acid content. The anodic peak of ascorbic acid in the phosphate buffer electrolyte (pH 6.86) was observed at a potential of +0.2 V. The current and peak area of ascorbic acid oxidation depended neither on the time nor on the conditioning potential of the sensor. The linear dependences of these parameters on the concentration of ascorbic acid stayed within 50–500 μmol/L (8.8–90 mg/L) at a scan rate of 0.1 mV/s. The single-wall carbon nanotube microsensor had a length of 0.5 cm and an average width of 400 μm. Its sensitivity was two times as high as that of a disk glassy carbon electrode with a diameter of 5 mm. The experimental sensors proved effective in determining ascorbic acid in food products, pharmaceuticals, and biological fluids.
- Open Access
Morphology and Phase Compositions of FePt and CoPt Nanoparticles Enriched with Noble Metal
The article reveals for the first time the features of nanoparticle morphology, phase compositions, and their changes when heating FePt and CoPt nanoalloys. Nanoparticles were obtained by co-reduction of precursor solution mixtures with hydrazine hydrate. The features were found by a complex of methods of X-ray diffraction (in situ XRD and X-ray scattering), TEM HR, and cyclic voltammetry. In addition, adsorbometry results were obtained, and the stability of different nanocluster structures was calculated by the molecular dynamics method. There were only FCC solid solutions in the X-ray patterns of the FePt and CoPt nanoalloys. According to XRD, in the case of nanoparticle synthesis with Fe and Co content less than 10 at. %, the composition of solid solutions was close to or practically equal to the composition of the as-synthesized nanoparticles quantified by inductively coupled plasma optical emission spectrometry. For systems synthesis with Fe and Co content greater than the above, the solubility limits (SLs) of Fe and Co in Pt were set 11.4 ± 0.7 at. % and 17.5 ± 0.6 at. %, respectively. Therefore, there were non-registered XRD extra-phases (XRNDPh-1) in the systems when CFe,Co ≥ SL. This statement was supported by the results of TEM HR and X-ray scattering: the smallest nanocrystals (1–2 nm) and amorphous particles were found, which qualitatively agreed with the sorbometry and SAXS results. Molecular dynamics calculations of stability for FePt and CoPt alloys claimed the structures of the most stable phase corresponded to phase diagrams (A1 and L12). Specific peculiarities of the morphology and compositions of the solid solutions of nanoalloys were established: structural blockiness (domain) and composition heterogeneity, namely, platinum enrichment of internal (deep) layers and homogenization of the nanoalloy compositions at relatively low temperatures (130–200 °C). The suggested model of the formation of nanoalloys during the synthesis, qualitatively, was compliant with the results of electrochemical deposition of FePt films on the surface of various electrodes. When nanocrystals of solid solutions (C(Fe, Co) < SL) were heated above specific temperatures, there were phase transformations with the formation of two-phase regions, with solid solutions enriched with platinum or iron (non-registered XRD phase XRNDPh-2). The newly formed phase was most likely intermetallic compounds, FePt3, CoPt3. As a result of the study, the model was developed, taking into account the nanoscale of the particles: XRDPh (A1, FeaPt1−a) → XRDPh (A1, Fem×a−xPtm−m×a+x) + XRNDPh-2 (Fen×a+yPtn−n×a−y) (here, m + n = 1, m ≤ 1, n ≤ 1).
Open AccessMorphology and Phase Compositions of FePt and CoPt Nanoparticles Enriched with Noble Metal
The article reveals for the first time the features of nanoparticle morphology, phase compositions, and their changes when heating FePt and CoPt nanoalloys. Nanoparticles were obtained by co-reduction of precursor solution mixtures with hydrazine hydrate. The features were found by a complex of methods of X-ray diffraction (in situ XRD and X-ray scattering), TEM HR, and cyclic voltammetry. In addition, adsorbometry results were obtained, and the stability of different nanocluster structures was calculated by the molecular dynamics method. There were only FCC solid solutions in the X-ray patterns of the FePt and CoPt nanoalloys. According to XRD, in the case of nanoparticle synthesis with Fe and Co content less than 10 at. %, the composition of solid solutions was close to or practically equal to the composition of the as-synthesized nanoparticles quantified by inductively coupled plasma optical emission spectrometry. For systems synthesis with Fe and Co content greater than the above, the solubility limits (SLs) of Fe and Co in Pt were set 11.4 ± 0.7 at. % and 17.5 ± 0.6 at. %, respectively. Therefore, there were non-registered XRD extra-phases (XRNDPh-1) in the systems when CFe,Co ≥ SL. This statement was supported by the results of TEM HR and X-ray scattering: the smallest nanocrystals (1–2 nm) and amorphous particles were found, which qualitatively agreed with the sorbometry and SAXS results. Molecular dynamics calculations of stability for FePt and CoPt alloys claimed the structures of the most stable phase corresponded to phase diagrams (A1 and L12). Specific peculiarities of the morphology and compositions of the solid solutions of nanoalloys were established: structural blockiness (domain) and composition heterogeneity, namely, platinum enrichment of internal (deep) layers and homogenization of the nanoalloy compositions at relatively low temperatures (130–200 °C). The suggested model of the formation of nanoalloys during the synthesis, qualitatively, was compliant with the results of electrochemical deposition of FePt films on the surface of various electrodes. When nanocrystals of solid solutions (C(Fe, Co) < SL) were heated above specific temperatures, there were phase transformations with the formation of two-phase regions, with solid solutions enriched with platinum or iron (non-registered XRD phase XRNDPh-2). The newly formed phase was most likely intermetallic compounds, FePt3, CoPt3. As a result of the study, the model was developed, taking into account the nanoscale of the particles: XRDPh (A1, FeaPt1−a) → XRDPh (A1, Fem×a−xPtm−m×a+x) + XRNDPh-2 (Fen×a+yPtn−n×a−y) (here, m + n = 1, m ≤ 1, n ≤ 1).
- 1 March 2023
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 13 (1) , 20-27
Carbon matrix nanostructured composites as a new type of supercapacitor electrode materials
Carbon matrix nanocomposites C / Au and C / MnxOy are obtained by a reduction of HAuCl4 and KMnO4 precursor solutions with single-walled carbon nanotubes or highly porous carbon materials obtained by high-temperature alkaline activation of various metamorphism degree coals.
- 1 March 2023
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 13 (1) , 20-27
Carbon matrix nanostructured composites as a new type of supercapacitor electrode materials
Carbon matrix nanocomposites C / Au and C / MnxOy are obtained by a reduction of HAuCl4 and KMnO4 precursor solutions with single-walled carbon nanotubes or highly porous carbon materials obtained by high-temperature alkaline activation of various metamorphism degree coals.
- Open Access
- 20 August 2019
- Published by Impact Journals, LLC in Oncotarget
- Vol. 10 (49) , 5070-5081
Idiotypic and anti-idiotypic antibodies against polycyclic aromatic hydrocarbon in human blood serum are new biomarkers of lung cancer
Oncotarget | https://doi.org/10.18632/oncotarget.27126 Ivan S. Grebenshchikov, Artem E. Studennikov, Vadim I. Ivanov, Natalia V. Ivanova, Victor A. Titov, Natalja E. Vergbickaya, Valentin A. Ustinov
- 20 August 2019
- Published by Impact Journals, LLC in Oncotarget
- Vol. 10 (49) , 5070-5081
Open AccessIdiotypic and anti-idiotypic antibodies against polycyclic aromatic hydrocarbon in human blood serum are new biomarkers of lung cancer
Oncotarget | https://doi.org/10.18632/oncotarget.27126 Ivan S. Grebenshchikov, Artem E. Studennikov, Vadim I. Ivanov, Natalia V. Ivanova, Victor A. Titov, Natalja E. Vergbickaya, Valentin A. Ustinov
- Open Access
- 7 June 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 525 (1) , 012019
The electrochemical behavior of nanostructured binary systems based on transition metals
By means cyclic and anodic linear sweep/stripping voltammetry methods the electrochemical behavior of bimetallic electrolytic nanoalloys and nanostructured powders Cu– Cd, Ni–Cd, Fe–Co, Fe–Ni was investigated in acidic (chloride, sulfate) and ammonia buffer media with the glassy carbon and carbon paste electrodes. The conditions (supporting electrolytes, concentrations of metal ions, voltammetric parameters) of the electrochemical synthesis and voltammetric characterization of the binary systems were established.
- 7 June 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 525 (1) , 012019
Open AccessThe electrochemical behavior of nanostructured binary systems based on transition metals
By means cyclic and anodic linear sweep/stripping voltammetry methods the electrochemical behavior of bimetallic electrolytic nanoalloys and nanostructured powders Cu– Cd, Ni–Cd, Fe–Co, Fe–Ni was investigated in acidic (chloride, sulfate) and ammonia buffer media with the glassy carbon and carbon paste electrodes. The conditions (supporting electrolytes, concentrations of metal ions, voltammetric parameters) of the electrochemical synthesis and voltammetric characterization of the binary systems were established.
- 5 December 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (3) , 036508
The non-equilibrium phases in the nanostructured Cd–Ni powders and their specific formation
- 5 December 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (3) , 036508
The non-equilibrium phases in the nanostructured Cd–Ni powders and their specific formation
- 5 September 2018
- Published by Springer Nature in Journal of Inorganic and Organometallic Polymers and Materials
- Vol. 29 (1) , 22-32
The Characteristics of the Atomic Structure and Morphology of the Ni-Cores in the Ni/Au Core–Shell Nanoparticles
- 5 September 2018
- Published by Springer Nature in Journal of Inorganic and Organometallic Polymers and Materials
- Vol. 29 (1) , 22-32
The Characteristics of the Atomic Structure and Morphology of the Ni-Cores in the Ni/Au Core–Shell Nanoparticles
- Open Access
- 22 February 2018
- Published by Voronezh State University in Сорбционные и хроматографические процессы
- Vol. 17 (6) , 970-978
Методические аспекты хромато-масс-спектрометрического анализа эфирного масла пихты сибирской
В работе на примере эфирного масла пихты сибирской обсуждаются особенности идентификации и определения количественного содержания соединений в сложной смеси органических веществ природного происхождения методом газожидкостной хроматографии и масс-спектрометрии (ГЖХ-МСД). Определены условия получения хроматографического профиля репрезентативных и характерных компонентов эфирного масла по ГОСТ ISO 10869-2015 с использованием капиллярной колонки НР-5ms. Показано влияние начальной температуры хроматографического анализа на степень перекрывания хроматографических пиков лимонена и β-фелландрена при совместном присутствии в эфирном масле пихты
- 22 February 2018
- Published by Voronezh State University in Сорбционные и хроматографические процессы
- Vol. 17 (6) , 970-978
Open AccessМетодические аспекты хромато-масс-спектрометрического анализа эфирного масла пихты сибирской
В работе на примере эфирного масла пихты сибирской обсуждаются особенности идентификации и определения количественного содержания соединений в сложной смеси органических веществ природного происхождения методом газожидкостной хроматографии и масс-спектрометрии (ГЖХ-МСД). Определены условия получения хроматографического профиля репрезентативных и характерных компонентов эфирного масла по ГОСТ ISO 10869-2015 с использованием капиллярной колонки НР-5ms. Показано влияние начальной температуры хроматографического анализа на степень перекрывания хроматографических пиков лимонена и β-фелландрена при совместном присутствии в эфирном масле пихты