Joachim Wendt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Joachim Wendt has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Dietmar Letzig
Helmholtz-Zentrum Geesthacht - Magnesium Innovation Centre; Max-Planck-Straße 1,21502 Geesthacht, GERMANY
5 shared publicationsA. Ludwig
2 shared publicationsB. Pustal
2 shared publicationsH. Fredriksson
2 shared publicationsJan Bohlen
GKSS Forschungszentrum
2 shared publicationsKerstin Hantzsche
GKSS Forschungszentrum
2 shared publications
Latest Publications
- 16 February 2015
- Published by Wiley
- p. 465-470
Microstructure Evolution of Different Magnesium Alloys During Twin Roll Casting
- 16 February 2015
- Published by Wiley
- p. 465-470
Microstructure Evolution of Different Magnesium Alloys During Twin Roll Casting
- 23 May 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 783-786, 534-536
Twin Roll Casting and Rolling of New Mg-Wrought Alloys for Body Protective Safety Equipment
Currently magnesium alloys are used for different applications in the transportation industry where cast magnesium alloys dominate the market. Although cast alloys predominate over wrought products such as extrusions, forgings, sheet and plate, the latter are also being used in a variety of different applications. Recently, a growing interest in the automotive industry in looking at potential applications for magnesium turned back towards wrought alloys. Typically, applications of magnesium sheets are sought in automotive or aeronautics industry. However, the spectrum of potential applications can be significantly expanded. For example, body protection systems for civil services like police, custom officers and prison personnel currently include anatomically shaped aluminium alloy sheets. Replacement of aluminium alloys by magnesium to result in substantial weight savings up to 30%.
- 23 May 2014
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 783-786, 534-536
Twin Roll Casting and Rolling of New Mg-Wrought Alloys for Body Protective Safety Equipment
Currently magnesium alloys are used for different applications in the transportation industry where cast magnesium alloys dominate the market. Although cast alloys predominate over wrought products such as extrusions, forgings, sheet and plate, the latter are also being used in a variety of different applications. Recently, a growing interest in the automotive industry in looking at potential applications for magnesium turned back towards wrought alloys. Typically, applications of magnesium sheets are sought in automotive or aeronautics industry. However, the spectrum of potential applications can be significantly expanded. For example, body protection systems for civil services like police, custom officers and prison personnel currently include anatomically shaped aluminium alloy sheets. Replacement of aluminium alloys by magnesium to result in substantial weight savings up to 30%.
- 9 October 2013
- Published by Wiley in Advanced Engineering Materials
- Vol. 16 (2) , 241-247
Processing of Magnesium Porous Structures by Infiltration Casting for Biomedical Applications
Magnesium and its alloys are currently considered to be a promising metallic biomaterial. The interest in magnesium alloys arises from their biocompatibility, bioabsorbility, and especially from their mechanical properties, which are more compatible to those of human bone than the mechanical properties of other metallic biomaterials, such as stainless steel and titanium. A medical application in which magnesium is gaining interest is regenerative medicine where scaffolds are used to create tissues from cells. For its application in regenerative medicine, the scaffolds have to present a 3D open‐cell structure. The main purpose of the present research is to set up the fabrication procedure necessary to manufacture porous magnesium scaffolds; for this the replication (infiltration) process has been used and adapted to process magnesium alloys, processing five different biodegradable magnesium alloys (AZ91E, WE43, ZM20, ZWM200, and ZXM200).
- 9 October 2013
- Published by Wiley in Advanced Engineering Materials
- Vol. 16 (2) , 241-247
Processing of Magnesium Porous Structures by Infiltration Casting for Biomedical Applications
Magnesium and its alloys are currently considered to be a promising metallic biomaterial. The interest in magnesium alloys arises from their biocompatibility, bioabsorbility, and especially from their mechanical properties, which are more compatible to those of human bone than the mechanical properties of other metallic biomaterials, such as stainless steel and titanium. A medical application in which magnesium is gaining interest is regenerative medicine where scaffolds are used to create tissues from cells. For its application in regenerative medicine, the scaffolds have to present a 3D open‐cell structure. The main purpose of the present research is to set up the fabrication procedure necessary to manufacture porous magnesium scaffolds; for this the replication (infiltration) process has been used and adapted to process magnesium alloys, processing five different biodegradable magnesium alloys (AZ91E, WE43, ZM20, ZWM200, and ZXM200).
- Top Cited Papers
- 1 October 2010
- Published by Elsevier in Scripta Materialia
- Vol. 63 (7) , 725-730
Effect of rare earth additions on microstructure and texture development of magnesium alloy sheets
- 1 October 2010
- Published by Elsevier in Scripta Materialia
- Vol. 63 (7) , 725-730
Top Cited PapersEffect of rare earth additions on microstructure and texture development of magnesium alloy sheets
- 30 June 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 654-656, 580-585
Development of the Microstructure and Texture of RE Containing Magnesium Alloys during Hot Rolling
Commercial magnesium alloys such as AZ31 exhibit strong crystallographic textures during massive deformation such as rolling. A randomisation of the texture, however, was found in alloys with rare earth (RE) elements in solid solution. This paper describes the development of microstructure and texture during rolling of the Al-free RE-containing wrought magnesium alloy ZEK100 during hot rolling. This alloy develops a strong texture with a pronounced component towards the transverse direction (TD) of the sheets. This TD component forms already after the first rolling pass, persists through all following passes and is further enhanced by subsequent heat treatment. These results are contrasted with results from a study on texture development of binary RE containing Mg-alloys, which show that the presence of RE elements alone is not responsible for the tilt of basal planes towards the TD. There is, however, a threshold concentration at which the texture begins to weaken.
- 30 June 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 654-656, 580-585
Development of the Microstructure and Texture of RE Containing Magnesium Alloys during Hot Rolling
Commercial magnesium alloys such as AZ31 exhibit strong crystallographic textures during massive deformation such as rolling. A randomisation of the texture, however, was found in alloys with rare earth (RE) elements in solid solution. This paper describes the development of microstructure and texture during rolling of the Al-free RE-containing wrought magnesium alloy ZEK100 during hot rolling. This alloy develops a strong texture with a pronounced component towards the transverse direction (TD) of the sheets. This TD component forms already after the first rolling pass, persists through all following passes and is further enhanced by subsequent heat treatment. These results are contrasted with results from a study on texture development of binary RE containing Mg-alloys, which show that the presence of RE elements alone is not responsible for the tilt of basal planes towards the TD. There is, however, a threshold concentration at which the texture begins to weaken.
- 11 August 2009
- Published by Springer Nature in JOM
- Vol. 61 (8) , 38-42
Mg sheet: the effect of process parameters and alloy composition on texture and mechanical properties
- 11 August 2009
- Published by Springer Nature in JOM
- Vol. 61 (8) , 38-42
Mg sheet: the effect of process parameters and alloy composition on texture and mechanical properties
- 1 October 2004
- Published by Maney Publishing in International Journal of Cast Metals Research
- Vol. 17 (5) , 295-310
Comparison of numerical simulation models for predicting temperature in solidification analysis with reference to air gap formation
International audienceAs a result of its influence on heat transfer between cast part and mould, air gap formation is an important problem for many casting processes. The general explanation for gap formation is that, as a result of stresses and distortions that are created from inhomogeneous cooling, shrinkage of the casting and expansion of the mould occur. In this paper, different thermomechanical approaches are applied to a well defined casting process using three commercial and one inhouse codes and their predictions are compared with experimental findings. The experimental data were obtained from the solidification and subsequent cooling of cylindrical castings of eutectic Al-13%Si and ternary Al-7%Si-0.3%Mg alloys. Based on these findings, the major differences between the predictions of the models and the actual formation of the air gap are discusse
- 1 October 2004
- Published by Maney Publishing in International Journal of Cast Metals Research
- Vol. 17 (5) , 295-310
Comparison of numerical simulation models for predicting temperature in solidification analysis with reference to air gap formation
International audienceAs a result of its influence on heat transfer between cast part and mould, air gap formation is an important problem for many casting processes. The general explanation for gap formation is that, as a result of stresses and distortions that are created from inhomogeneous cooling, shrinkage of the casting and expansion of the mould occur. In this paper, different thermomechanical approaches are applied to a well defined casting process using three commercial and one inhouse codes and their predictions are compared with experimental findings. The experimental data were obtained from the solidification and subsequent cooling of cylindrical castings of eutectic Al-13%Si and ternary Al-7%Si-0.3%Mg alloys. Based on these findings, the major differences between the predictions of the models and the actual formation of the air gap are discusse
- 5 February 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (1-2) , 78-79
Cooperation within MEBSP on the Subject of Air Gap Formation During a Casting Process
The goal of quantitatively predicting air gap growth in casting processes is still not reached. Subgroup IV of the international research platform MEBSP is tackling the problem with both an experimental approach (see Figure for a layout currently used at the Royal Institute of Technology) and a variety of simulation programs, being used by different participating institutes.
- 5 February 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (1-2) , 78-79
Cooperation within MEBSP on the Subject of Air Gap Formation During a Casting Process
The goal of quantitatively predicting air gap growth in casting processes is still not reached. Subgroup IV of the international research platform MEBSP is tackling the problem with both an experimental approach (see Figure for a layout currently used at the Royal Institute of Technology) and a variety of simulation programs, being used by different participating institutes.
- 5 February 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (1-2) , 58-61
How High‐Pressure Die‐Cast Component (HPDC) Foundries Benefit from Numerical Simulation
The value of simulating the high pressure die‐casting process is demonstrated by showing and discussing the abilities of state‐of‐the‐art modeling of a typical component of the electronics industry. Process parameters, which can be optimized by simulation as well as process improvements, are identified. An evaluation of HPDC‐modeling in terms of process improvement, quality, and efforts is carried out and prospects for future developments are given.
- 5 February 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (1-2) , 58-61
How High‐Pressure Die‐Cast Component (HPDC) Foundries Benefit from Numerical Simulation
The value of simulating the high pressure die‐casting process is demonstrated by showing and discussing the abilities of state‐of‐the‐art modeling of a typical component of the electronics industry. Process parameters, which can be optimized by simulation as well as process improvements, are identified. An evaluation of HPDC‐modeling in terms of process improvement, quality, and efforts is carried out and prospects for future developments are given.
- 22 October 1999
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 318-320, 297-302
Gas Porosity Defects in Duplex Stainless Steel Castings
- 22 October 1999
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 318-320, 297-302
Gas Porosity Defects in Duplex Stainless Steel Castings