Du Ngoc Uy Lan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Du Ngoc Uy Lan has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Volker Altstädt
Polymer Engineering, University of Bayreuth, Bayreuth, Germany
7 shared publications - Holger Ruckdäschel
Department of Polymer Engineering University of Bayreuth Bayreuth Germany
5 shared publications - Baharin Azahari
Universiti Sains Malaysia
4 shared publications - Christian Bethke
Department of Polymer Engineering, University of Bayreuth, Universitaetsstrasse 30, 95447 Bayreuth, Germany
4 shared publications - Firuz Zainuddin
Universiti Malaysia Perlis
4 shared publications - Zulkifli Mohamad Ariff
Universiti Sains Malaysia image/svg+xml
4 shared publications
Latest Publications
- Open Access
- 23 March 2023
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 59 (3) , 231-247
Foaming epoxy-amine-carbamate: The effect of different neat amines on rheological and cellular morphology
The use of carbamate to foam epoxy depends significantly on the precured modulus to stabilize the cellular structure. The optimum precured modulus is developed from the reaction of epoxy resin and the neat amine. The selection of the neat amine relies on its reaction temperature with epoxy, which is required to be below the decomposition temperature of carbamate. This study investigates the effect of three different neat amines on the rheological behavior of foaming epoxy-carbamate-amine. They are bisphenol-A diglycidyl ether epoxy (DGEBA), isophorone diamine carbamate (IDPA.CO2), N-aminoethylpiperazine (AEP), 2,4-Diamino-1-methyl-cyclohexan (DMC) and isophorone diamine (IDPA). The mixtures of DGEBA-amine-carbamate are filled in 25% and 75% of the volume of a closed mold. Precuring is carried out at 60°C for 2 h. The foaming and complete curing are conducted at 180°C for 1 h. Having H-active at piperazine, AEP reacts with DGEBA faster and develops a higher precured modulus compared to DMC and IDPA. It is important to note that DGEBA-AEP-IDPA.CO2 exhibits viscoelastic behavior beyond 138°C, seen by its rheological storage modulus lower than loss modulus and its tan delta larger than 1. The reaction between DGEBA and the H-active piperazine of AEP leads only to linear linkage and is unable to further crosslink compared to the primary amine (-NH2). This results in a lower glass transition temperature Tg of DGEBA-AEP-IPDA.CO2. The effect of amine on foaming is more obviously at 25% filling level. DGEBA-AEP-IPDA.CO2 has more spherical and homogeneous cellular structure and the density of 285 kg/m3. Having quite similar chemical structure, both DGEBA-DMC-IPDA.CO2 and DGEBA-IPDA-IPDA.CO2 produce the epoxy foams having cell-interconnection and coalescence; their densities are also similar 301 kg/m3 and 305 kg/m3, respectively. All the foams are closed-cell at 75% of filling level. The cell morphologies are well reflecting the foaming modulus and tan delta behavior.
- 23 March 2023
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 59 (3) , 231-247
Open AccessFoaming epoxy-amine-carbamate: The effect of different neat amines on rheological and cellular morphology
The use of carbamate to foam epoxy depends significantly on the precured modulus to stabilize the cellular structure. The optimum precured modulus is developed from the reaction of epoxy resin and the neat amine. The selection of the neat amine relies on its reaction temperature with epoxy, which is required to be below the decomposition temperature of carbamate. This study investigates the effect of three different neat amines on the rheological behavior of foaming epoxy-carbamate-amine. They are bisphenol-A diglycidyl ether epoxy (DGEBA), isophorone diamine carbamate (IDPA.CO2), N-aminoethylpiperazine (AEP), 2,4-Diamino-1-methyl-cyclohexan (DMC) and isophorone diamine (IDPA). The mixtures of DGEBA-amine-carbamate are filled in 25% and 75% of the volume of a closed mold. Precuring is carried out at 60°C for 2 h. The foaming and complete curing are conducted at 180°C for 1 h. Having H-active at piperazine, AEP reacts with DGEBA faster and develops a higher precured modulus compared to DMC and IDPA. It is important to note that DGEBA-AEP-IDPA.CO2 exhibits viscoelastic behavior beyond 138°C, seen by its rheological storage modulus lower than loss modulus and its tan delta larger than 1. The reaction between DGEBA and the H-active piperazine of AEP leads only to linear linkage and is unable to further crosslink compared to the primary amine (-NH2). This results in a lower glass transition temperature Tg of DGEBA-AEP-IPDA.CO2. The effect of amine on foaming is more obviously at 25% filling level. DGEBA-AEP-IPDA.CO2 has more spherical and homogeneous cellular structure and the density of 285 kg/m3. Having quite similar chemical structure, both DGEBA-DMC-IPDA.CO2 and DGEBA-IPDA-IPDA.CO2 produce the epoxy foams having cell-interconnection and coalescence; their densities are also similar 301 kg/m3 and 305 kg/m3, respectively. All the foams are closed-cell at 75% of filling level. The cell morphologies are well reflecting the foaming modulus and tan delta behavior.
- Open Access
Preparation of pros-foam sheets and their epoxy foams using the solid-state carbamate-foaming technique
- Open Access
Novel Expandable Epoxy Beads and Epoxy Particle Foam
Expanded polymeric beads offer the advantage of being able to produce parts with complex geometries through a consolidation process. However, established polymeric beads are made of thermoplastics, deform and melt beyond their temperature services. In this manuscript, a new technique is proposed to fabricate expandable epoxy beads (EEBs), then expand and fuse them to produce epoxy particle foams (EPFs). This technique is called solid-state carbamate foaming technique. For production of EEBs, a mixture of epoxy, carbamate and hardener is prepared and poured into a 10 mL syringe. The mixture is manually extruded into 60 °C water to obtain a cylindric shape. The extrudate is then further cured to obtain an epoxy oligomer behaving rheological tan delta 3 and 2 at 60 °C. The extrudate is cut into pellets to obtain EEBs. The EEBs are then loaded into an aluminum mold and placed in an oven at 160 °C to expand, fuse to obtain EPFs of 212 kg/m3 and 258 kg/m3. The obtained EPFs provide a Tg of 150–154 °C. The fusion boundaries in EPFs are well formed. Thus, the produced EPFs exhibit a compressive modulus of 50–70 MPa, with a torsion storage modulus at 30 °C of 34–56 MPa.
Open AccessNovel Expandable Epoxy Beads and Epoxy Particle Foam
Expanded polymeric beads offer the advantage of being able to produce parts with complex geometries through a consolidation process. However, established polymeric beads are made of thermoplastics, deform and melt beyond their temperature services. In this manuscript, a new technique is proposed to fabricate expandable epoxy beads (EEBs), then expand and fuse them to produce epoxy particle foams (EPFs). This technique is called solid-state carbamate foaming technique. For production of EEBs, a mixture of epoxy, carbamate and hardener is prepared and poured into a 10 mL syringe. The mixture is manually extruded into 60 °C water to obtain a cylindric shape. The extrudate is then further cured to obtain an epoxy oligomer behaving rheological tan delta 3 and 2 at 60 °C. The extrudate is cut into pellets to obtain EEBs. The EEBs are then loaded into an aluminum mold and placed in an oven at 160 °C to expand, fuse to obtain EPFs of 212 kg/m3 and 258 kg/m3. The obtained EPFs provide a Tg of 150–154 °C. The fusion boundaries in EPFs are well formed. Thus, the produced EPFs exhibit a compressive modulus of 50–70 MPa, with a torsion storage modulus at 30 °C of 34–56 MPa.
- Open Access
New Insights on Expandability of Pre-Cured Epoxy Using a Solid-State CO2-Foaming Technique
Foaming an epoxy is challenging because the process involves the curing reaction of epoxy and hardener (from monomer to oligomer, to a gel and a final three-dimensional crosslinked network) and the loading of gas phase into the epoxy phase to develop the cellular structure. The latter process needs to be carried out at the optimum curing stage of epoxy to avoid cell coalescence and to allow expansion. The environmental concern regarding the usage of chemical blowing agent also limits the development of epoxy foams. To surmount these challenges, this study proposes a solid-state CO2 foaming of epoxy. Firstly, the resin mixture of diglycidylether of bisphenol-A (DGEBA) epoxy and polyamide hardener is pre-cured to achieve various solid-state sheets (preEs) of specific storage moduli. Secondly, these preEs undergo CO2 absorption using an autoclave. Thirdly, CO2 absorbed preEs are allowed to free-foam/expand in a conventional oven at various temperatures; lastly, the epoxy foams are post-cured. PreE has a distinctive behavior once being heated; the storage modulus is reduced and then increases due to further curing. Epoxy foams in a broad range of densities could be fabricated. PreE with a storage modulus of 4 × 104–1.5 × 105 Pa at 30 °C could be foamed to densities of 0.32–0.45 g/cm3. The cell morphologies were revealed to be star polygon shaped, spherical and irregularly shaped. The research proved that the solid-state CO2-foaming technique can be used to fabricate epoxy foams with controlled density.
Open AccessNew Insights on Expandability of Pre-Cured Epoxy Using a Solid-State CO2-Foaming Technique
Foaming an epoxy is challenging because the process involves the curing reaction of epoxy and hardener (from monomer to oligomer, to a gel and a final three-dimensional crosslinked network) and the loading of gas phase into the epoxy phase to develop the cellular structure. The latter process needs to be carried out at the optimum curing stage of epoxy to avoid cell coalescence and to allow expansion. The environmental concern regarding the usage of chemical blowing agent also limits the development of epoxy foams. To surmount these challenges, this study proposes a solid-state CO2 foaming of epoxy. Firstly, the resin mixture of diglycidylether of bisphenol-A (DGEBA) epoxy and polyamide hardener is pre-cured to achieve various solid-state sheets (preEs) of specific storage moduli. Secondly, these preEs undergo CO2 absorption using an autoclave. Thirdly, CO2 absorbed preEs are allowed to free-foam/expand in a conventional oven at various temperatures; lastly, the epoxy foams are post-cured. PreE has a distinctive behavior once being heated; the storage modulus is reduced and then increases due to further curing. Epoxy foams in a broad range of densities could be fabricated. PreE with a storage modulus of 4 × 104–1.5 × 105 Pa at 30 °C could be foamed to densities of 0.32–0.45 g/cm3. The cell morphologies were revealed to be star polygon shaped, spherical and irregularly shaped. The research proved that the solid-state CO2-foaming technique can be used to fabricate epoxy foams with controlled density.
- Open Access
Tailoring Epoxy Resin Foams by Pre-Curing with Neat Amine Hardeners and Its Derived Carbamates
The use of amine-based carbamates with their dual function, acting as amine curing agents and CO2 blowing agents after their decomposition without by-products, are promising for ecofriendly epoxy foams as high-performance materials. However, controlling cell morphology requires a proper adjustment of the viscosity at the foaming step. The viscosity is altered not only by blending neat amine and its derived carbamate at a fixed pre-curing time, but also by changing the pre-curing time at a fixed blend ratio. Within this study, diglycidylether of bisphenol A (DGEBA) epoxy resin is mixed with different blend ratios of isophorone diamine (IPDA) and its derived carbamate (B-IPDA). The systems are characterized by DSC and rheology experiments to identify the pre-curing effects on the derived epoxy foams. Epoxy foams at a blend ratio of 30/70w IPDA/B-IPDA showed the best foam morphology and an optimum Tg compared to other blend ratios. Furthermore, it was found that both pre-curing times, 2 h and 3 h, for the 30/70w IPDA/B-IPDA system reveal a more homogeneous cell structure. The study proves that the blending of neat amine and carbamate is beneficial for the foaming performance of carbamate systems.
Open AccessTailoring Epoxy Resin Foams by Pre-Curing with Neat Amine Hardeners and Its Derived Carbamates
The use of amine-based carbamates with their dual function, acting as amine curing agents and CO2 blowing agents after their decomposition without by-products, are promising for ecofriendly epoxy foams as high-performance materials. However, controlling cell morphology requires a proper adjustment of the viscosity at the foaming step. The viscosity is altered not only by blending neat amine and its derived carbamate at a fixed pre-curing time, but also by changing the pre-curing time at a fixed blend ratio. Within this study, diglycidylether of bisphenol A (DGEBA) epoxy resin is mixed with different blend ratios of isophorone diamine (IPDA) and its derived carbamate (B-IPDA). The systems are characterized by DSC and rheology experiments to identify the pre-curing effects on the derived epoxy foams. Epoxy foams at a blend ratio of 30/70w IPDA/B-IPDA showed the best foam morphology and an optimum Tg compared to other blend ratios. Furthermore, it was found that both pre-curing times, 2 h and 3 h, for the 30/70w IPDA/B-IPDA system reveal a more homogeneous cell structure. The study proves that the blending of neat amine and carbamate is beneficial for the foaming performance of carbamate systems.
- 17 September 2020
- Published by Wiley in Polymer Composites
- Vol. 42 (1) , 83-97
The thermal‐mechanical degradation of mineral‐filled polypropylene‐ethylene copolymer composites during extrusion process
This work proposes a new understanding of the side effect of mineral fillers in polymer compounding that caused different levels of thermo‐mechanical degradation (TMD) during extrusion. Three mineral fillers, silica (random shape), kaolin (platy), and wollastonite (needle‐like), were selected and compounded with the polypropylene‐ethylene copolymer (PPcoE) using a twin‐screw extruder. Their influences on the TMD of PPcoE were examined by checking the substances in the extrudates using Fourier transform infrared spectroscopy. The built‐up shear stress causing by mineral filler in PPcoE composite (Δτcom) as the root of TMD was measured and estimated using capillary rheometer. In this study, TMD is classified as two levels: chain scission and oxidization. These fillers were found to accelerate the TMD mechanism and generate the oxidised products during extrusion. The silica filler caused the highest Δτcom, the lowest tensile strength, and elongation at break of PPcoE composites. The kaolin filler gave the most potent accelerating effect on oxidization, resulted in the formation of tertiary alcohol, and the highest ester contents in PPcoE composites; although, its composite had the lowest Δτcom among the fillers. Lastly, wollastonite filler provided higher Δτcom than kaolin composite, the second‐highest formation of alkene products, yet better retention in elongation at break compared to the silica‐filled PPcoE composite. In general, the side effect of mineral filler on TMD was a larger particle size always comes with higher chain scission, simpler particle morphology gives a smoother built‐up shear stress and minimizes TMD, and filler having hydroxyl groups catalyzes the oxidization TMD.
- 17 September 2020
- Published by Wiley in Polymer Composites
- Vol. 42 (1) , 83-97
The thermal‐mechanical degradation of mineral‐filled polypropylene‐ethylene copolymer composites during extrusion process
This work proposes a new understanding of the side effect of mineral fillers in polymer compounding that caused different levels of thermo‐mechanical degradation (TMD) during extrusion. Three mineral fillers, silica (random shape), kaolin (platy), and wollastonite (needle‐like), were selected and compounded with the polypropylene‐ethylene copolymer (PPcoE) using a twin‐screw extruder. Their influences on the TMD of PPcoE were examined by checking the substances in the extrudates using Fourier transform infrared spectroscopy. The built‐up shear stress causing by mineral filler in PPcoE composite (Δτcom) as the root of TMD was measured and estimated using capillary rheometer. In this study, TMD is classified as two levels: chain scission and oxidization. These fillers were found to accelerate the TMD mechanism and generate the oxidised products during extrusion. The silica filler caused the highest Δτcom, the lowest tensile strength, and elongation at break of PPcoE composites. The kaolin filler gave the most potent accelerating effect on oxidization, resulted in the formation of tertiary alcohol, and the highest ester contents in PPcoE composites; although, its composite had the lowest Δτcom among the fillers. Lastly, wollastonite filler provided higher Δτcom than kaolin composite, the second‐highest formation of alkene products, yet better retention in elongation at break compared to the silica‐filled PPcoE composite. In general, the side effect of mineral filler on TMD was a larger particle size always comes with higher chain scission, simpler particle morphology gives a smoother built‐up shear stress and minimizes TMD, and filler having hydroxyl groups catalyzes the oxidization TMD.
- Open Access
- 1 May 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 864 (1) , 012114
Effect of filler size and loading on thermo-mechanical degradation of polypropylene-ethylene/wollastonite composite
This study is to understand the side effect of wollastonite fillers in polymer compounding that caused different levels of thermo-mechanical degradation (TMD) during extrusion. Wollastonite has a needle-like structure with different ratio of L/D; it compounded with the polypropylene-ethylene copolymer (PPcoE) using a twin-screw extruder. The effect on the TMD of PPcoE was determined by analysing the by-products within the extrudates via FTIR. The rheology of PPcoE composite was measured using a capillary rheometer, and the thermal stability of composite was studied using TGA. In this study, TMD is classified as two levels: chain scission and oxidisation. The wollastonite filler were found to accelerate the TMD mechanism and generated oxidised products during extrusion. The reduction of filler size effectively minimised the chain cleavage of PPcoE matrix, also come with improvement in thermal stability. However, increasing the filler loading had a dominant effect of inducing more chain cleavage on the polymer matrix.
- 1 May 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 864 (1) , 012114
Open AccessEffect of filler size and loading on thermo-mechanical degradation of polypropylene-ethylene/wollastonite composite
This study is to understand the side effect of wollastonite fillers in polymer compounding that caused different levels of thermo-mechanical degradation (TMD) during extrusion. Wollastonite has a needle-like structure with different ratio of L/D; it compounded with the polypropylene-ethylene copolymer (PPcoE) using a twin-screw extruder. The effect on the TMD of PPcoE was determined by analysing the by-products within the extrudates via FTIR. The rheology of PPcoE composite was measured using a capillary rheometer, and the thermal stability of composite was studied using TGA. In this study, TMD is classified as two levels: chain scission and oxidisation. The wollastonite filler were found to accelerate the TMD mechanism and generated oxidised products during extrusion. The reduction of filler size effectively minimised the chain cleavage of PPcoE matrix, also come with improvement in thermal stability. However, increasing the filler loading had a dominant effect of inducing more chain cleavage on the polymer matrix.
- 25 July 2019
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 56 (1) , 105-118
Viscoelastic epoxy foams by an aqueous emulsion foaming process
The research proposed an aqueous emulsion foaming process to produce a viscoelastic epoxy foam having a density of 0.33–0.36 g/cm3 from the polyamide–epoxy adduct, which uses a reverse ratio of epoxy and polyamide hardener. The process is simple, economical and uses no surfactant, thanks to the emulsifying ability of polyamide hardener. Firstly, the mixture of excess polyamide, epoxy and sodium bicarbonate was emulsified with distilled water using high-speed stirring to form dispersed epoxy droplets in water. Secondly, a solution of ammonium chloride was added, which reacted with sodium bicarbonate to produce carbon dioxide and ammonia gases dispersed in the epoxy emulsion. The expanding gases induced flocculation and partial coalescence of the epoxy droplets; sequentially water molecules were entrapped within them. Finally, a curing process was carried out to stabilise the foam morphology and structure. Two types of pore morphologies were observed: a large foam-pore generated from blowing-agent gases and a cell-wall pore formed from the vapourisation of entrapped water (as the void template). Porosity and pore morphologies depended on blowing-agent content, and the viscoelasticity was affected by the epoxy/polyamide ratio. The obtained viscoelastic foams showed a large number of interconnected cells and exhibited high compression set values.
- 25 July 2019
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 56 (1) , 105-118
Viscoelastic epoxy foams by an aqueous emulsion foaming process
The research proposed an aqueous emulsion foaming process to produce a viscoelastic epoxy foam having a density of 0.33–0.36 g/cm3 from the polyamide–epoxy adduct, which uses a reverse ratio of epoxy and polyamide hardener. The process is simple, economical and uses no surfactant, thanks to the emulsifying ability of polyamide hardener. Firstly, the mixture of excess polyamide, epoxy and sodium bicarbonate was emulsified with distilled water using high-speed stirring to form dispersed epoxy droplets in water. Secondly, a solution of ammonium chloride was added, which reacted with sodium bicarbonate to produce carbon dioxide and ammonia gases dispersed in the epoxy emulsion. The expanding gases induced flocculation and partial coalescence of the epoxy droplets; sequentially water molecules were entrapped within them. Finally, a curing process was carried out to stabilise the foam morphology and structure. Two types of pore morphologies were observed: a large foam-pore generated from blowing-agent gases and a cell-wall pore formed from the vapourisation of entrapped water (as the void template). Porosity and pore morphologies depended on blowing-agent content, and the viscoelasticity was affected by the epoxy/polyamide ratio. The obtained viscoelastic foams showed a large number of interconnected cells and exhibited high compression set values.
- Open Access
Effect of Resin and Blocked/Unblocked Hardener Mixture on the Production of Epoxy Foams with CO2 Blocked Hardener in Batch Foaming Process
The present study focuses on the processing and properties of epoxy foams by the use of CO2 blocked hardener N-aminoethylpiperazine (B-AEP) and different resins. Although some studies described the foaming with carbamates, little attention has been given to the interaction of resin properties (such as viscosity) on the foaming performance. Therefore, two resins, diglycidyl ether of bisphenol-A (DGEBA) and epoxy novolac (EN), as well as their 50:50 blend, were foamed with B-AEP and unblocked/blocked AEP hardener mixtures in a batch foaming process. Furthermore, the commercially available chemical blowing agent para-toluenesulfonyl hydrazide (TSH) was used as a benchmark for commonly used chemical blowing agents. The lowest density in this study was reached by the DGEBA+B-AEP system in the range of 215 kg/m3 with the drawback of an inhomogeneous cell structure and high cell size distribution. The best cell morphology and lowest cell size distribution was reached with the EN+15:85% unblocked:blocked hardener mixture, resulting in a density in the range of 394 kg/m3. A syntactic foam was achieved by a DGEBA+50:50% unblocked:blocked hardener mixture with a density of around 496 kg/m3. It was found that a higher viscosity of the resin lead to an increase in the density and a decrease in the cell size distribution range as a result of a closer expansion time window.
Open AccessEffect of Resin and Blocked/Unblocked Hardener Mixture on the Production of Epoxy Foams with CO2 Blocked Hardener in Batch Foaming Process
The present study focuses on the processing and properties of epoxy foams by the use of CO2 blocked hardener N-aminoethylpiperazine (B-AEP) and different resins. Although some studies described the foaming with carbamates, little attention has been given to the interaction of resin properties (such as viscosity) on the foaming performance. Therefore, two resins, diglycidyl ether of bisphenol-A (DGEBA) and epoxy novolac (EN), as well as their 50:50 blend, were foamed with B-AEP and unblocked/blocked AEP hardener mixtures in a batch foaming process. Furthermore, the commercially available chemical blowing agent para-toluenesulfonyl hydrazide (TSH) was used as a benchmark for commonly used chemical blowing agents. The lowest density in this study was reached by the DGEBA+B-AEP system in the range of 215 kg/m3 with the drawback of an inhomogeneous cell structure and high cell size distribution. The best cell morphology and lowest cell size distribution was reached with the EN+15:85% unblocked:blocked hardener mixture, resulting in a density in the range of 394 kg/m3. A syntactic foam was achieved by a DGEBA+50:50% unblocked:blocked hardener mixture with a density of around 496 kg/m3. It was found that a higher viscosity of the resin lead to an increase in the density and a decrease in the cell size distribution range as a result of a closer expansion time window.
- 1 January 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 16, 1708-1714
Mechanical properties of polytetrafluoroethylene (PTFE) powder reinforced bio-based palm oil polyurethane (POPU) composite foam
- 1 January 2019
- Published by Elsevier in Materials Today: Proceedings
- Vol. 16, 1708-1714
Mechanical properties of polytetrafluoroethylene (PTFE) powder reinforced bio-based palm oil polyurethane (POPU) composite foam