Fengyi Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fengyi Huang has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
Xusheng Tang
School of Cyber Science and Engineering, Southeast University, Nanjing, China
18 shared publicationsYouming Zhang
School of Cyber Science and Engineering Southeast University Nanjing China
11 shared publications- Youming Zhang
Southeast University
11 shared publications Zhennan Wei
Southeast University
9 shared publicationsNan Jiang
RFIC Department S‐TEK Research Center Shanghai China
6 shared publications- Xusheng Tang
Southeast University
6 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (10) , 1041-1045
A 3-D Integrated 6--18 GHz Reconfigurable Filtering LNA Using a Hyper-Abrupt Varactor Die
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (10) , 1041-1045
A 3-D Integrated 6--18 GHz Reconfigurable Filtering LNA Using a Hyper-Abrupt Varactor Die
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (9) , 2192-2195
Equivalent Circuit Modeling of RF Degradation in TSVs for Millimeter-Wave Applications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (9) , 2192-2195
Equivalent Circuit Modeling of RF Degradation in TSVs for Millimeter-Wave Applications
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A 6–18-GHz, 10-W GaN Balanced Power Amplifier Employing Harmonic Suppression and Harmonic Phase-Control Techniques
This letter presents a 6–18-GHz, 10-W balanced power amplifier (BPA) monolithic microwave integrated circuit (MMIC) fabricated in a 0.25- $\mu $ m gallium nitride on silicon carbide (GaN-on-SiC) high-electron-mobility transistor (HEMT) process. To meet the stringent harmonic suppression requirements of ultrawideband radar, electronic-warfare systems, and satellite-communication applications, a modified elliptic-filter output matching network is proposed and combined with a harmonic phase-control technique to boost power-added efficiency (PAE) and pout uniformly across the full band. Under continuous-wave measurement conditions, the MMIC delivers a power gain of 19.7–21.2 dB, a saturated output power of 40.2–41.1 dBm, and a PAE of 24%–36% over the entire 6–18-GHz band. Second-harmonic suppression (H2S) is −45.6 dB at 10 GHz, and spurious-emission suppression exceeds 70 dB. The DC supply voltage is 24 V, and the core chip occupies 15.2 mm2, demonstrating a highly compact balanced architecture.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
A 6–18-GHz, 10-W GaN Balanced Power Amplifier Employing Harmonic Suppression and Harmonic Phase-Control Techniques
This letter presents a 6–18-GHz, 10-W balanced power amplifier (BPA) monolithic microwave integrated circuit (MMIC) fabricated in a 0.25- $\mu $ m gallium nitride on silicon carbide (GaN-on-SiC) high-electron-mobility transistor (HEMT) process. To meet the stringent harmonic suppression requirements of ultrawideband radar, electronic-warfare systems, and satellite-communication applications, a modified elliptic-filter output matching network is proposed and combined with a harmonic phase-control technique to boost power-added efficiency (PAE) and pout uniformly across the full band. Under continuous-wave measurement conditions, the MMIC delivers a power gain of 19.7–21.2 dB, a saturated output power of 40.2–41.1 dBm, and a PAE of 24%–36% over the entire 6–18-GHz band. Second-harmonic suppression (H2S) is −45.6 dB at 10 GHz, and spurious-emission suppression exceeds 70 dB. The DC supply voltage is 24 V, and the core chip occupies 15.2 mm2, demonstrating a highly compact balanced architecture.
- 4 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (1) , 48-52
A Full-Band Reconfigurable CMOS Transceiver in the 50 MHz-to-7 GHz Frequency Range
This brief presents a full-band multi-mode reconfigurable CMOS transceiver (TRX) covering TDD/FDD 3GPP/WLAN, candidate 6G and WiFi 7 (5.925–7.125 GHz) frequency bands. A novel multi-mode architecture is proposed in the receiver (RX) chain, which supports reconfigurable low-noise (LN) and high-linearity (HL) operations with the RX chain reused for feedback observation (FBO). The RX achieves a noise figure of 2.0–5.4 dB in the LN mode, an IP1dB of –4.6 dBm and an IIP3 of +5.3 dBm in the HL mode. In the TX chain, a modified RFATT integrated with a symmetrical passive resistor network (SPRN) is utilized to achieve high precision, large dynamic power control and high linearity. The TX achieves >92 dB TX power control range with 0.25-dB step, 62.0 dBc ACLR, –66.1 dBc IRR, and –38.8 dB EVM at 40-MHz 256QAM 802.11ac signal. The LO generation chain incorporates a quadrature error correction circuit with a single VCO of 67% tuning range, exhibiting a phase noise of –128.2 dBc/Hz @1MHz (with 2.1 GHz carrier). Powered by 1.2/2.5-V supplies, the 3.54×2.75 mm2 TRX circuit consumes 0.25 W/0.4 W in TDD/FDD modes. The present chip provides a fully reconfigurable solution for any carrier frequency from 50 MHz to 7 GHz with an instantaneous RF bandwidth of 110 MHz, with major performances comparable to the prior arts without resorting to digital calibration circuits.
- 4 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (1) , 48-52
A Full-Band Reconfigurable CMOS Transceiver in the 50 MHz-to-7 GHz Frequency Range
This brief presents a full-band multi-mode reconfigurable CMOS transceiver (TRX) covering TDD/FDD 3GPP/WLAN, candidate 6G and WiFi 7 (5.925–7.125 GHz) frequency bands. A novel multi-mode architecture is proposed in the receiver (RX) chain, which supports reconfigurable low-noise (LN) and high-linearity (HL) operations with the RX chain reused for feedback observation (FBO). The RX achieves a noise figure of 2.0–5.4 dB in the LN mode, an IP1dB of –4.6 dBm and an IIP3 of +5.3 dBm in the HL mode. In the TX chain, a modified RFATT integrated with a symmetrical passive resistor network (SPRN) is utilized to achieve high precision, large dynamic power control and high linearity. The TX achieves >92 dB TX power control range with 0.25-dB step, 62.0 dBc ACLR, –66.1 dBc IRR, and –38.8 dB EVM at 40-MHz 256QAM 802.11ac signal. The LO generation chain incorporates a quadrature error correction circuit with a single VCO of 67% tuning range, exhibiting a phase noise of –128.2 dBc/Hz @1MHz (with 2.1 GHz carrier). Powered by 1.2/2.5-V supplies, the 3.54×2.75 mm2 TRX circuit consumes 0.25 W/0.4 W in TDD/FDD modes. The present chip provides a fully reconfigurable solution for any carrier frequency from 50 MHz to 7 GHz with an instantaneous RF bandwidth of 110 MHz, with major performances comparable to the prior arts without resorting to digital calibration circuits.
- 23 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1-13
Analysis and Design of Ultra-Wideband mm-Wave Injection-Locked Frequency Multiplier Based on Complementary-Phase Cascade-Parallel Resonator
A complementary-phase resonator (CPR) consisting of two parallel sub-networks based on complementary-phase concept is presented, whose phase frequency responses are designed to counteract each other so as to obtain an ultra-wide continuous phase plateau with small ripples and an injection current boosting (ICB) characteristic, allowing significant extension of the locking range (LR) for the millimeter-wave (mm-wave) injection-locked frequency multipliers (ILFMs). Subsequently, the widely used output buffer (cascaded with the ILFM core and incorporating a transformer as its load) is merged into the CPR to form a complementary-phase cascade-parallel resonator (CP2R), which poses a cascaded signal transmission path and a parallel complementary structure similar to the CPR, inheriting the advantages of complementary phases and facilitating an increased resonator impedance magnitude and a compact chip area. The proof-of-concept design of an injection-locked frequency doubler relying on the CP2R is fabricated in a 40-nm CMOS process. It achieves a LR of 41.7% from 72 to 110 GHz under 0-dBm injection power, covering the entire W-band without resonator tuning or multi ratio mode switching. As the injection power is reduced to −3 dBm, the LR of the CP2R-ILFM remains competitive, spanning from 78 to 106 GHz. The measured output power is above −12 dBm from 80 to 102 GHz with a maximal output power of −6.2 dBm at 88 GHz. The chip occupies a core area of 0.039 mm2 and dissipates 9.4 mW from a 0.9-V voltage supply.
- 23 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1-13
Analysis and Design of Ultra-Wideband mm-Wave Injection-Locked Frequency Multiplier Based on Complementary-Phase Cascade-Parallel Resonator
A complementary-phase resonator (CPR) consisting of two parallel sub-networks based on complementary-phase concept is presented, whose phase frequency responses are designed to counteract each other so as to obtain an ultra-wide continuous phase plateau with small ripples and an injection current boosting (ICB) characteristic, allowing significant extension of the locking range (LR) for the millimeter-wave (mm-wave) injection-locked frequency multipliers (ILFMs). Subsequently, the widely used output buffer (cascaded with the ILFM core and incorporating a transformer as its load) is merged into the CPR to form a complementary-phase cascade-parallel resonator (CP2R), which poses a cascaded signal transmission path and a parallel complementary structure similar to the CPR, inheriting the advantages of complementary phases and facilitating an increased resonator impedance magnitude and a compact chip area. The proof-of-concept design of an injection-locked frequency doubler relying on the CP2R is fabricated in a 40-nm CMOS process. It achieves a LR of 41.7% from 72 to 110 GHz under 0-dBm injection power, covering the entire W-band without resonator tuning or multi ratio mode switching. As the injection power is reduced to −3 dBm, the LR of the CP2R-ILFM remains competitive, spanning from 78 to 106 GHz. The measured output power is above −12 dBm from 80 to 102 GHz with a maximal output power of −6.2 dBm at 88 GHz. The chip occupies a core area of 0.039 mm2 and dissipates 9.4 mW from a 0.9-V voltage supply.
- 18 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (5) , 723-727
A 4 × 4 Fully Integrated RF Transceiver in 6 GHz Frequency Band With Single-Channel Bandwidth of 400 MHz and PHY Data-Rate of 8.8 Gbps
This brief presents a fully integrated CMOS 4×4 MIMO RF transceiver (TRX) with single-channel bandwidth (BW) of 400 MHz in the 6 GHz band (5.925–7.125 GHz). In the receiver (RX) frontend, an improved noise-canceling low noise amplifier (LNA) and a cross-coupled transconductance (GM) with IIP2 enhancement is implemented. In the transmitter (TX) frontend, a power amplifier driver (PAD) is integrated with cascade AM-PM distortion compensation to eliminate the AM-PM distortion. A hierarchical LO distribution network is employed in the 1-to-4 LO distribution chain to enhance the consistency among the LO branches. The single-chip TRX is reconfigurable for TDD/FDD operation, with the RX exhibiting a noise figure of 3.5–4.1 dB, a gain control range of 45 dB with 1 dB step and ±0.2 dB gain flatness. The TX output spectrum exhibits >32 dBc signal to noise ratio (SNR). The RX and TX error vector magnitudes (EVMs) are –30.2 dB and –30.5 dB, respectively, with 160 MHz BW 256QAM. A TX-to-RX PHY data-rate of 8.8 Gbps based on 4×4 MIMO is achieved, with other major parameters comparable to the prior arts without resorting to digital calibration circuits.
- 18 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (5) , 723-727
A 4 × 4 Fully Integrated RF Transceiver in 6 GHz Frequency Band With Single-Channel Bandwidth of 400 MHz and PHY Data-Rate of 8.8 Gbps
This brief presents a fully integrated CMOS 4×4 MIMO RF transceiver (TRX) with single-channel bandwidth (BW) of 400 MHz in the 6 GHz band (5.925–7.125 GHz). In the receiver (RX) frontend, an improved noise-canceling low noise amplifier (LNA) and a cross-coupled transconductance (GM) with IIP2 enhancement is implemented. In the transmitter (TX) frontend, a power amplifier driver (PAD) is integrated with cascade AM-PM distortion compensation to eliminate the AM-PM distortion. A hierarchical LO distribution network is employed in the 1-to-4 LO distribution chain to enhance the consistency among the LO branches. The single-chip TRX is reconfigurable for TDD/FDD operation, with the RX exhibiting a noise figure of 3.5–4.1 dB, a gain control range of 45 dB with 1 dB step and ±0.2 dB gain flatness. The TX output spectrum exhibits >32 dBc signal to noise ratio (SNR). The RX and TX error vector magnitudes (EVMs) are –30.2 dB and –30.5 dB, respectively, with 160 MHz BW 256QAM. A TX-to-RX PHY data-rate of 8.8 Gbps based on 4×4 MIMO is achieved, with other major parameters comparable to the prior arts without resorting to digital calibration circuits.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (12) , 4869-4873
0.78–1.22° RMS Phase Error, 0.14–0.32 dB RMS Gain Error, K-Band 4-Channel Phased Array Receiver IC for Satcom on the Move (SOTM)
This brief presents a high accuracy high linearity K-Band 4-channel phased array receiver for satellite communication (SATCOM). Structural improvement and parameter optimization have been carried out to enhance the phase and gain control precision. The presented receiver employs a novel L-C compensation and variable resistance technique in the quadrature all-pass filter (QAF) for phase shifter (PS) to reduce the phase error. Neutralization capacitance and redundancy control bit are adopted in the attenuator (ATT) to reduce the gain error. A 3-stage low noise amplifier (LNA) has been optimized to provide high gain, high input-referred 1-dB gain compression point and low noise. The receiver achieves a 360° phase shifting range with a 6-bit resolution and a 31.5 dB attenuation range with 0.5 dB step. The measured root mean square (RMS) phase error and gain error are 0.78°–1.22° and 0.14–0.32 dB, respectively over the frequency of 17 GHz to 23 GHz. Each channel achieves a measured gain of 23 dB, an input-referred 1-dB gain compression point (IP1dB) of –29.8 dBm at the maximum gain, and a low noise figure (NF) of 3.4–3.9 dB. The 4-channel receiver is implemented in 40-nm CMOS processes and occupies a chip area of 3.85 mm2.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (12) , 4869-4873
0.78–1.22° RMS Phase Error, 0.14–0.32 dB RMS Gain Error, K-Band 4-Channel Phased Array Receiver IC for Satcom on the Move (SOTM)
This brief presents a high accuracy high linearity K-Band 4-channel phased array receiver for satellite communication (SATCOM). Structural improvement and parameter optimization have been carried out to enhance the phase and gain control precision. The presented receiver employs a novel L-C compensation and variable resistance technique in the quadrature all-pass filter (QAF) for phase shifter (PS) to reduce the phase error. Neutralization capacitance and redundancy control bit are adopted in the attenuator (ATT) to reduce the gain error. A 3-stage low noise amplifier (LNA) has been optimized to provide high gain, high input-referred 1-dB gain compression point and low noise. The receiver achieves a 360° phase shifting range with a 6-bit resolution and a 31.5 dB attenuation range with 0.5 dB step. The measured root mean square (RMS) phase error and gain error are 0.78°–1.22° and 0.14–0.32 dB, respectively over the frequency of 17 GHz to 23 GHz. Each channel achieves a measured gain of 23 dB, an input-referred 1-dB gain compression point (IP1dB) of –29.8 dBm at the maximum gain, and a low noise figure (NF) of 3.4–3.9 dB. The 4-channel receiver is implemented in 40-nm CMOS processes and occupies a chip area of 3.85 mm2.
- 12 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (5) , 504-507
A 58–110 GHz 4.2 dB Minimum NF CMOS LNA With Broadband Simultaneous Noise and Impedance Matching
This letter presents a hybrid series-shunt LC tank matching technique, which constructs an imaginary-impedance part for impendence (power) matching and cancels the imaginary-impedance deviations caused by the aggravated load and parasitic effects in millimeter-wave (mm-wave) high-frequency band, allowing broadband simultaneous noise and impedance matching (BSNIM) for mm-wave CMOS low-noise amplifier (LNA). The proposed matching network has been synthesized into a triple-coupled transformer-based matching network further to enable a compact and robust solution in differential circuit design. To validate the proposed BSNIM techniques, an $E$ / $W$ -band LNA is fabricated with 40-nm CMOS, and achieves less than $-$ 10 dB S11 from 58 to 110 GHz and a low noise figure (NF) of 4.2–6.9 dB from 58 to 100 GHz. The peak gain of the LNA is 16.4 dB at 85 GHz with a 3-dB gain bandwidth (BW) from 70 to 91 GHz, while consuming 20.7 mW from 0.9-V supply.
- 12 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (5) , 504-507
A 58–110 GHz 4.2 dB Minimum NF CMOS LNA With Broadband Simultaneous Noise and Impedance Matching
This letter presents a hybrid series-shunt LC tank matching technique, which constructs an imaginary-impedance part for impendence (power) matching and cancels the imaginary-impedance deviations caused by the aggravated load and parasitic effects in millimeter-wave (mm-wave) high-frequency band, allowing broadband simultaneous noise and impedance matching (BSNIM) for mm-wave CMOS low-noise amplifier (LNA). The proposed matching network has been synthesized into a triple-coupled transformer-based matching network further to enable a compact and robust solution in differential circuit design. To validate the proposed BSNIM techniques, an $E$ / $W$ -band LNA is fabricated with 40-nm CMOS, and achieves less than $-$ 10 dB S11 from 58 to 110 GHz and a low noise figure (NF) of 4.2–6.9 dB from 58 to 100 GHz. The peak gain of the LNA is 16.4 dB at 85 GHz with a 3-dB gain bandwidth (BW) from 70 to 91 GHz, while consuming 20.7 mW from 0.9-V supply.
- 6 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (8) , 2729-2733
On the Design of Broadband Truly Balanced Inductor-Less Differential-to-Single-Ended Converter in CMOS Friendly to Wire-Bond Package
This brief presents a broadband inductor-less differential to single-ended (D2S) converter employing complementary structure with series resistor. The developed D2S converter has a unique advantage in terms of amplitude and phase balance performance, achieving true balance in theory and while maintaining wire-bond package friendliness. The D2S converter is validated in a prototype of broadband driver amplifier (DA) for the transmitter front-end and fabricated in 65 nm CMOS process. The measurement results show an amplitude and phase error of less than 0.2 dB and 1∘, respectively, over a frequency range of 0.1 to 6 GHz. The proposed D2S occupies a core chip area of only 0.04×0.1 mm and consumes 6.5–7.4 mW power from a 1.2 V supply voltage.
- 6 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (8) , 2729-2733
On the Design of Broadband Truly Balanced Inductor-Less Differential-to-Single-Ended Converter in CMOS Friendly to Wire-Bond Package
This brief presents a broadband inductor-less differential to single-ended (D2S) converter employing complementary structure with series resistor. The developed D2S converter has a unique advantage in terms of amplitude and phase balance performance, achieving true balance in theory and while maintaining wire-bond package friendliness. The D2S converter is validated in a prototype of broadband driver amplifier (DA) for the transmitter front-end and fabricated in 65 nm CMOS process. The measurement results show an amplitude and phase error of less than 0.2 dB and 1∘, respectively, over a frequency range of 0.1 to 6 GHz. The proposed D2S occupies a core chip area of only 0.04×0.1 mm and consumes 6.5–7.4 mW power from a 1.2 V supply voltage.