JSJian Song

Jian Song

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jian Song has a total of 48 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Core/Shell Nanoparticles on the Fretting Behavior of Gold Coated Electrical Contacts

    by Haomiao Yuan, Jian Song

    A protective coating is usually applied in electrical contacts to prevent corrosion and fretting corrosion and to extend the lifetime of electrical contacts. A gold coating is recommended for applications functioning under very severe operation conditions, such as highly corrosive environments, or where a stable current should be reliably guaranteed even at very low voltage. However, the high price of gold material limits the use of gold coatings. Thus, a method to reduce gold consumption, for example to lower the required gold coating thickness without decreasing the lifetime and performance of the gold coating is of great interest. In this paper, a method to fabricate a novel gold coating co-deposited with nanoparticles with a core/shell structure, i.e. Ag (shell) @ Al 2 O 3 (core), is introduced. The influence of the nanoparticle concentration in the electrolyte and the agitation of the galvanic bath on the lifetime of the nanoparticles co-deposited gold coating is investigated. By co-depositing the Ag @ Al 2 O 3 nanoparticles, the microhardness of the gold coating is increased by around 30% compared to the pure gold coating; however, there is no significant difference in the microhardness among the co-deposited coatings fabricated with the different Ag @ Al 2 O 3 nanoparticle concentration in the electrolyte. The lifetime is also significantly prolonged by nanoparticle co-deposition. A favored nanoparticle concentration in the electrolyte is determined with regard to the topic of lifetime. The gold coatings made of the favored nanoparticle concentration in the electrolyte show a 2.2-fold of the average lifetime of the pure gold coating in the wear and fretting corrosion test. When considering the best lifetime of the nanoparticle co-deposited coating, the value is 4.3-fold of the lifetime of the pure gold coating. By employing a higher bath agitation in the electroplating process, a smoother nanoparticles co-deposited gold coating with fewer pores and finer grains is produced, which improves the average lifetime of the coatings to 3.7-fold of the co-deposited coatings produced under a lower bath agitation, while the standard deviation of the lifetime of the coatings in the wear and fretting corrosion test is decreased. Moreover, the mechanism of lifetime enhancement is discussed.

  • Open Access

    The State of Health of Electrical Connectors

    by Jian Song, Abhay Shukla, Roman Probst

    For modern machines, factories and electric and autonomous vehicles, the importance of vreliable electrical connectors cannot be overstated. With an increasing number of connectors being used in machines, factories and vehicles, ensuring their reliability is crucial for comfort and safety alike. One of the key indicators of reliability is the lifetime of connectors. To evaluate the lifetime of electrical connectors, a testing method and a model for calculating their lifetime based on the test data were developed. The results from these tests were compared to failure analysis data from long-term field operations. The findings indicate that the laboratory tests can accurately reproduce the main failures observed in the field. However, such lifetime tests can be time- and labor-intensive. To address this challenge, a data-driven method is proposed that predicts the lifetime of electrical connectors using statistical analysis of electrical contact resistance data collected from short-term tests. The predictions from this method were compared to actual results obtained from long-term tests. A strong correlation was observed between the contact resistance development in short-term tests and the number of failures in later stages of testing. Thus, apart from predicting the lifetime of connectors, this method can also be applied for failure prognosis in real-time operations.


  • Open Access

    Methods of Material and Surface Analysis for the Evaluation of Failure Modes for Electrical Connectors

    by Philipp Kolmer, Abhay Shukla, Jian Song

    The development of autonomous vehicles and the integration of new information and communication technologies are making the reliability of electrical systems and components in modern vehicles increasingly important. Electrical connectors are a crucial component in an electrical on-board system. They are exposed to a wide variety of influences by the environment and operating conditions. Thus, the degradation of electrical connectors can occur. Material and surface analysis methods are the tools used to analyze the degradation mechanisms in connectors after lifetime tests, as well as in field operations. Within the framework of this study, a wide variety of methods from the analytical scope are presented and discussed. The connector surfaces degraded by different failure mechanisms are analyzed using various material and surface analysis methods. The quality and the nature of the analyses results obtained from various analysis methods are compared. Also, this study deals with the benefits and limitations, as well as the effort and the specific challenges of different material and surface analytical methods for the evaluation of failure mechanisms from the point of view of a material and surface analyst.


  • Vergleichende Untersuchung der Verschleißbilder von Steckverbindern aus Reibverschleiß- und Vibrationsprüfungen mit unterschiedlichen Prüfrichtungen

    by Dirk Hilmert, Kevin Krüger, Jian Song

    In this study a comparison between the wear patterns of electrical connectors resulting from two different test types, namely fretting corrosion test and vibration test, is conducted. In both tests, the excitation directions include the mating direction as well as the orthogonal directions corresponding to the mating direction. Different measurement techniques are used to identify similarities and differences between the wear resulting from these test types. The results show fundamentally different critical directions with regard to wear for the respective test types. Furthermore, it is shown that the induced movement of the fretting tests lead to a higher degree of wear than the vibration tests. Also, it is not adequately possible to establish a direct relationship between the induced movement and the excitation amplitude caused by the attached wires since there is a superposition of several movements in the case of real applications.


  • Open Access

    Analysis of the Interstrand and Strand/Connector Resistance Relations in Wire Connection Systems

    by Carsten Kuckuck, Pascal Lodige, Michael Blauth, Haomiao Yuan, Jian Song

    The basic function of wire connection systems is to assure a low resistance and a stable long-term electromechanical connection. The quality of this connection is determined by the quality of a large number of electromechanical interstrand and strand/connector contacts. The aim of this study is to analyze the parameters that influence the performance of wire connection systems with a new measurement method. A detailed analysis enables a deeper understanding and provides extended information about the inner electromechanical connection behavior. This analysis method can be used both for the fundamental research and the optimization of wire connection systems design. Hexagonal crimp connections with different wire surface conditions were analyzed. Furthermore, a numerical calculation method is introduced to describe the performance of wire connection systems in order to gain a deeper understanding of the results.


  • Open Access

    An Improved Calculation Model for the Prediction of the Wear of Coated Electrical Contacts

    by Haomiao Yuan, Jian Song

    To connect terminals in a cyber–physical system, large quantities of electrical contacts are used. In order to guarantee a high reliability of the system, the lifetime of the electrical contacts should be very long. Thus, it is of great importance to understand the failure mechanism and then to predict the lifetime of the electrical contacts. For the applications under high thermal and/or mechanical loads, noble plating is a good choice, considering its inertness to oxidation. For noble plating, one of the most critical failure mechanisms is the fretting wear. Wear debris generated in the contact area, acting as the third bodies, will greatly influence the further wear behavior and electrical performance. In this study, the state of the art regarding third bodies is firstly reviewed, and then the influence of the third bodies on the wear and electrical performance is investigated, from the aspects of lifetime and the element distributions in contact area. Finally, an example of prediction of the wear of noble plating is shown with the consideration of the third bodies. Based on this study, by involving the third bodies, the wear of noble plating can be predicted with a higher accuracy.