Bumman Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bumman Kim has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
Jangheon Kim
Department of Electrical and Computer Engineering, University of Waterloo, Waterloo, Canada
6 shared publicationsIldu Kim
Department of Electrical Engineering, Pohang University of Science and Technology(POSTECH), Gyeongbuk, 790-784, Republic of Korea
5 shared publicationsJunghwan Moon
Samsung Electronics Company Ltd., Suwon, Republic of Korea
5 shared publications- Daehyun Kang
Samsung Electronics, Suwon, South Korea
4 shared publications Jooseung Kim
Department of Electrical Engineering, Pohang University of Science and Technology, Pohang, South Korea
4 shared publicationsKyunghoon Moon
Department of Electrical Engineering, Pohang University of Science and Technology, 77, Cheongam-Ro, Nam-Gu, Gyeongbuk, Republic of Korea
4 shared publications
Latest Publications
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 19 (7) , 116-133
Saturated PAs for High Efficiency: Operation of Saturated Amplifiers Having the Optimum Voltage Waveform to Achieve Maximum Efficiency
High efficiency is a crucial design consideration. This is true not only for power amplifiers (PAs), but also for transmitters such as the Doherty PA and the supply-modulated PA, due to thermal management, reliability, and size [1]-[3] issues. Several PA topologies, e.g., class E, class F, and class F-1, have been proposed to achieve high efficiency [3]-[17]. In the class-E PA, a transistor acts as a switch, which has very low loss. The voltage of the class-E amplifier is supported through the charging and discharging of a transistor's output capacitor, which is parallel with the switch. Because this amplifier tunes all the harmonic components using the LC resonator, it delivers the highest efficiency among the proposed amplifiers. The capacitor's charging step, however, cannot be abrupt; above the theoretical maximum frequency fmax,E, the capacitor cannot be discharged quickly enough to support the ideal waveform [3], [4]. As a result, the efficiency of the class-E PA is significantly degraded at a frequency above fmax,E [3]-[6]. Also, the power density of the class-E amplifier is low because of the low content of the fundamental voltage component.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 19 (7) , 116-133
Saturated PAs for High Efficiency: Operation of Saturated Amplifiers Having the Optimum Voltage Waveform to Achieve Maximum Efficiency
High efficiency is a crucial design consideration. This is true not only for power amplifiers (PAs), but also for transmitters such as the Doherty PA and the supply-modulated PA, due to thermal management, reliability, and size [1]-[3] issues. Several PA topologies, e.g., class E, class F, and class F-1, have been proposed to achieve high efficiency [3]-[17]. In the class-E PA, a transistor acts as a switch, which has very low loss. The voltage of the class-E amplifier is supported through the charging and discharging of a transistor's output capacitor, which is parallel with the switch. Because this amplifier tunes all the harmonic components using the LC resonator, it delivers the highest efficiency among the proposed amplifiers. The capacitor's charging step, however, cannot be abrupt; above the theoretical maximum frequency fmax,E, the capacitor cannot be discharged quickly enough to support the ideal waveform [3], [4]. As a result, the efficiency of the class-E PA is significantly degraded at a frequency above fmax,E [3]-[6]. Also, the power density of the class-E amplifier is low because of the low content of the fundamental voltage component.
- 9 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (5) , 2356-2362
Ultralow-Power 2.4-GHz Receiver With All Passive Sliding-IF Mixer
This paper presents a 2.4-GHz ISM band ultralow-power receiver with a passive sliding-IF (SIF) mixer structure. A self-biased inverter-based low noise amplifier which has high FOM and good linearity in low-power operation is employed. All passive SIF mixer is proposed to avoid power consumption in an active mixer and high-frequency operation of a nonoverlapping 4-phase generator. The passive SIF mixer is analyzed for optimization and interstage matching. A dual mode programmable gain amplifier (PGA) based on Sallen-key low-pass filter is proposed to enhance gain control range. The proposed PGA has 55 dB gain range with power consumption of 120 μW. The overall receiver has 15-70-dB gain, 6.5-dB noise figure, -10-dBm IIP3 (at 3-MHz tone spacing), and consumes 640 μW at 2.45-GHz input frequency.
- 9 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 66 (5) , 2356-2362
Ultralow-Power 2.4-GHz Receiver With All Passive Sliding-IF Mixer
This paper presents a 2.4-GHz ISM band ultralow-power receiver with a passive sliding-IF (SIF) mixer structure. A self-biased inverter-based low noise amplifier which has high FOM and good linearity in low-power operation is employed. All passive SIF mixer is proposed to avoid power consumption in an active mixer and high-frequency operation of a nonoverlapping 4-phase generator. The passive SIF mixer is analyzed for optimization and interstage matching. A dual mode programmable gain amplifier (PGA) based on Sallen-key low-pass filter is proposed to enhance gain control range. The proposed PGA has 55 dB gain range with power consumption of 120 μW. The overall receiver has 15-70-dB gain, 6.5-dB noise figure, -10-dBm IIP3 (at 3-MHz tone spacing), and consumes 640 μW at 2.45-GHz input frequency.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 40, 220-223
Linear CMOS power amplifier at Ka-band with ultra-wide video bandwidth
A highly linear power amplifier (PA) with ultra-wide video bandwidth is designed at a Ka-band for 5G application. To get a high linearity with high efficiency, a deep class-AB topology with 2nd harmonic control circuits is employed, reducing the 3rd order nonlinearity. Further, an efficient low-drop out (LDO) regulator is proposed to suppress the memory effect generated by the envelope and fundamental nonlinear mixing. The PA, composed of 3 cascaded common-source (CS) stages, achieves peak PAE of 21.8% at output power of 14 dBm with 22 dB gain. The 3rd order inter-modulation distortion (IMD3) at an output power of 5 dBm is under -30 dBc for a video bandwidth of 1 GHz. The PA and LDO are fabricated in a 65 nm CMOS process and occupy 0.53 mm2.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 40, 220-223
Linear CMOS power amplifier at Ka-band with ultra-wide video bandwidth
A highly linear power amplifier (PA) with ultra-wide video bandwidth is designed at a Ka-band for 5G application. To get a high linearity with high efficiency, a deep class-AB topology with 2nd harmonic control circuits is employed, reducing the 3rd order nonlinearity. Further, an efficient low-drop out (LDO) regulator is proposed to suppress the memory effect generated by the envelope and fundamental nonlinear mixing. The PA, composed of 3 cascaded common-source (CS) stages, achieves peak PAE of 21.8% at output power of 14 dBm with 22 dB gain. The 3rd order inter-modulation distortion (IMD3) at an output power of 5 dBm is under -30 dBc for a video bandwidth of 1 GHz. The PA and LDO are fabricated in a 65 nm CMOS process and occupy 0.53 mm2.
- Open Access
- 1 December 2016
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 52 (25) , 2044-2046
Highly efficient digital quadrature transmitter with dual VDD and dynamic cell selection
A digital quadrature dual VDD transmitter with a switched capacitor power combiner is presented. To improve the efficiency, the cell in the transmitter is dynamically selected to minimise the voltage across the capacitors, thereby minimising the discharging loss. The chip is fabricated in 28‐nm CMOS process. The implemented transmitter has a peak power of 17.2 dBm with a PAE of 37.4% at 880 MHz. The average power is 7.9 dBm with a PAE of 23.6% under ACLR of −32 dBc using a 10 MHz, 16 QAM, and 6.9 dB LTE signal.
- 1 December 2016
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 52 (25) , 2044-2046
Open AccessHighly efficient digital quadrature transmitter with dual VDD and dynamic cell selection
A digital quadrature dual VDD transmitter with a switched capacitor power combiner is presented. To improve the efficiency, the cell in the transmitter is dynamically selected to minimise the voltage across the capacitors, thereby minimising the discharging loss. The chip is fabricated in 28‐nm CMOS process. The implemented transmitter has a peak power of 17.2 dBm with a PAE of 37.4% at 880 MHz. The average power is 7.9 dBm with a PAE of 23.6% under ACLR of −32 dBc using a 10 MHz, 16 QAM, and 6.9 dB LTE signal.
- Top Cited Papers
- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 64 (12) , 4535-4544
Highly Linear mm-Wave CMOS Power Amplifier
A Ka-band highly linear power amplifier (PA) is implemented in 28-nm bulk CMOS technology. Using a deep class-AB PA topology with appropriate harmonic control circuit, highly linear and efficient PAs are designed at millimeter-wave band. This PA architecture provides a linear PA operation close to the saturated power. Also elaborated harmonic tuning and neutralization techniques are used to further improve the transistor gain and stability. A two-stack PA is designed for higher gain and output power than a common source (CS) PA. Additionally, average power tracking (APT) is applied to further reduce the power consumption at a low power operation and, hence, extend battery life. Both the PAs are tested with two different signals at 28.5 GHz; they are fully loaded long-term evolution (LTE) signal with 16-quadrature amplitude modulation (QAM), a 7.5-dB peak-to-average power ratio (PAPR), and a 20-MHz bandwidth (BW), and a wireless LAN (WLAN) signal with 64-QAM, a 10.8-dB PAPR, and an 80-MHz BW. The CS/two-stack PAs achieve power-added efficiency (PAE) of 27%/25%, error vector magnitude (EVM) of 5.17%/3.19%, and adjacent channel leakage ratio (ACLR$_{\mathrm{ E-UTRA}}$ ) of −33/−33 dBc, respectively, with an average output power of 11/14.6 dBm for the LTE signal. For the WLAN signal, the CS/2-stack PAs achieve the PAE of 16.5%/17.3%, and an EVM of 4.27%/4.21%, respectively, at an average output power of 6.8/11 dBm.- 24 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 64 (12) , 4535-4544
Top Cited PapersHighly Linear mm-Wave CMOS Power Amplifier
A Ka-band highly linear power amplifier (PA) is implemented in 28-nm bulk CMOS technology. Using a deep class-AB PA topology with appropriate harmonic control circuit, highly linear and efficient PAs are designed at millimeter-wave band. This PA architecture provides a linear PA operation close to the saturated power. Also elaborated harmonic tuning and neutralization techniques are used to further improve the transistor gain and stability. A two-stack PA is designed for higher gain and output power than a common source (CS) PA. Additionally, average power tracking (APT) is applied to further reduce the power consumption at a low power operation and, hence, extend battery life. Both the PAs are tested with two different signals at 28.5 GHz; they are fully loaded long-term evolution (LTE) signal with 16-quadrature amplitude modulation (QAM), a 7.5-dB peak-to-average power ratio (PAPR), and a 20-MHz bandwidth (BW), and a wireless LAN (WLAN) signal with 64-QAM, a 10.8-dB PAPR, and an 80-MHz BW. The CS/two-stack PAs achieve power-added efficiency (PAE) of 27%/25%, error vector magnitude (EVM) of 5.17%/3.19%, and adjacent channel leakage ratio (ACLR$_{\mathrm{ E-UTRA}}$ ) of −33/−33 dBc, respectively, with an average output power of 11/14.6 dBm for the LTE signal. For the WLAN signal, the CS/2-stack PAs achieve the PAE of 16.5%/17.3%, and an EVM of 4.27%/4.21%, respectively, at an average output power of 6.8/11 dBm. - 9 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 64 (11) , 3612-3622
Voltage-Combined CMOS Doherty Power Amplifier Based on Transformer
This paper presents a voltage-combined CMOS Doherty power amplifier (PA) based on a transformer. The dynamic load modulation of the two-way transformer is analyzed in detail. A comparison between the current- and voltage-combined Doherty PAs shows that the Doherty PA based on a voltage-combining method delivers a broad bandwidth (BW) with a larger load tolerance. The proposed Doherty PA achieves close to ideal load modulation without additional offset line by manipulation of the output capacitances. For demonstration purposes, the PA and output combining transformer are implemented using a 0.18-μm CMOS process and an FR4 printed circuit board, respectively. The PA is tested at 880 MHz using a fully loaded long-term evolution signal with 16-quadrature amplitude modulation, 7.5-dB peak-to-average power ratio, and 10-MHz BW. The PA delivers a gain of 13.3 dB, a power-added efficiency of 47.4%, an error vector magnitude of 3.85%, and E-UTRAACLR of -33 dBc at an average output power of 27 dBm. This simple voltage-combined Doherty PA without any additional circuitry achieves good performance. These results show that the proposed CMOS Doherty PA is suitable for handheld PA applications.
- 9 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 64 (11) , 3612-3622
Voltage-Combined CMOS Doherty Power Amplifier Based on Transformer
This paper presents a voltage-combined CMOS Doherty power amplifier (PA) based on a transformer. The dynamic load modulation of the two-way transformer is analyzed in detail. A comparison between the current- and voltage-combined Doherty PAs shows that the Doherty PA based on a voltage-combining method delivers a broad bandwidth (BW) with a larger load tolerance. The proposed Doherty PA achieves close to ideal load modulation without additional offset line by manipulation of the output capacitances. For demonstration purposes, the PA and output combining transformer are implemented using a 0.18-μm CMOS process and an FR4 printed circuit board, respectively. The PA is tested at 880 MHz using a fully loaded long-term evolution signal with 16-quadrature amplitude modulation, 7.5-dB peak-to-average power ratio, and 10-MHz BW. The PA delivers a gain of 13.3 dB, a power-added efficiency of 47.4%, an error vector magnitude of 3.85%, and E-UTRAACLR of -33 dBc at an average output power of 27 dBm. This simple voltage-combined Doherty PA without any additional circuitry achieves good performance. These results show that the proposed CMOS Doherty PA is suitable for handheld PA applications.
- 12 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 64 (10) , 3224-3231
Accurate Offset Line Design of Doherty Amplifier With Compensation of Peaking Amplifier Phase Variation
Accurate offset line design of Doherty amplifier is investigated to compensate the phase variation of the carrier and peaking amplifiers. The offset line at the peaking amplifier not only blocks the power leakage to the peaking amplifier at the OFF-state, but also assists in the load modulation like the offset line at the carrier amplifier. However, with the conventional offset line, the load is not properly modulated due to the phase variation of the class C peaking amplifier. Since the offset lines at the carrier and peaking power amplifiers (PAs) properly eliminate the reactive parts during the Doherty load modulation, the offset lines can handle the phase variation also. To compensate the phase variation, additional lines are added at the carrier and peaking amplifiers for the proper load modulation. With the new offset line, the load of the peaking amplifier can be properly modulated and the efficiency at the high power region is increased. In addition, the efficiency at the low power region is also increased due to the larger load of the carrier amplifier at the power region. The enhanced performance is validated by the Doherty PA employing CGH40045 devices at 1.94 GHz, applying drain bias voltage of 50 V. For the long term evolution signal with a 6.5 dB peak-to-average power ratio, the Doherty amplifier with the new offset line delivers a drain/power-added efficiency of 57%/54.8% which is 3.5%/3.1% higher than that with the conventional offset line at an output power of 45.4 dBm with the linearity -48.3 dBc using digital predistortion linearization.
- 12 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 64 (10) , 3224-3231
Accurate Offset Line Design of Doherty Amplifier With Compensation of Peaking Amplifier Phase Variation
Accurate offset line design of Doherty amplifier is investigated to compensate the phase variation of the carrier and peaking amplifiers. The offset line at the peaking amplifier not only blocks the power leakage to the peaking amplifier at the OFF-state, but also assists in the load modulation like the offset line at the carrier amplifier. However, with the conventional offset line, the load is not properly modulated due to the phase variation of the class C peaking amplifier. Since the offset lines at the carrier and peaking power amplifiers (PAs) properly eliminate the reactive parts during the Doherty load modulation, the offset lines can handle the phase variation also. To compensate the phase variation, additional lines are added at the carrier and peaking amplifiers for the proper load modulation. With the new offset line, the load of the peaking amplifier can be properly modulated and the efficiency at the high power region is increased. In addition, the efficiency at the low power region is also increased due to the larger load of the carrier amplifier at the power region. The enhanced performance is validated by the Doherty PA employing CGH40045 devices at 1.94 GHz, applying drain bias voltage of 50 V. For the long term evolution signal with a 6.5 dB peak-to-average power ratio, the Doherty amplifier with the new offset line delivers a drain/power-added efficiency of 57%/54.8% which is 3.5%/3.1% higher than that with the conventional offset line at an output power of 45.4 dBm with the linearity -48.3 dBc using digital predistortion linearization.
- 26 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 25 (10) , 678-680
CMOS Power Amplifier on Top of Embedded Transformer for Compact Module
A small-sized high-performance complementary metal-oxide-semiconductor (CMOS) power amplifier (PA) module is presented. To reduce insertion loss of the output matching network (OMN), an off-chip transformer is designed on a FR-4 printed circuit board (PCB). To minimize the area of the OMN, the transformer is embedded underneath the PA chip. Coupling between the PA and the transformer is minimized so that the performance is not affected. For the 7.5 dB peak-to-average power ratio, 16-QAM long-term evolution signal, the proposed CMOS PA module achieves a power-added efficiency of 38.5% and an adjacent channel leakage ratio level under -31 dBc at an average output power of 27.5 dBm. The proposed technique can be used in any wireless Tx applications requiring small form-factor and high performance.
- 26 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 25 (10) , 678-680
CMOS Power Amplifier on Top of Embedded Transformer for Compact Module
A small-sized high-performance complementary metal-oxide-semiconductor (CMOS) power amplifier (PA) module is presented. To reduce insertion loss of the output matching network (OMN), an off-chip transformer is designed on a FR-4 printed circuit board (PCB). To minimize the area of the OMN, the transformer is embedded underneath the PA chip. Coupling between the PA and the transformer is minimized so that the performance is not affected. For the 7.5 dB peak-to-average power ratio, 16-QAM long-term evolution signal, the proposed CMOS PA module achieves a power-added efficiency of 38.5% and an adjacent channel leakage ratio level under -31 dBc at an average output power of 27.5 dBm. The proposed technique can be used in any wireless Tx applications requiring small form-factor and high performance.
- Open Access
- 30 April 2015
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 15 (2) , 63-75
Design of an Advanced CMOS Power Amplifier
- 30 April 2015
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 15 (2) , 63-75
Open AccessDesign of an Advanced CMOS Power Amplifier
- 22 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 62 (3) , 567-578
Linear Doherty Power Amplifier With an Enhanced Back-Off Efficiency Mode for Handset Applications
This paper presents a linear Doherty power amplifier (PA) with enhanced back-off efficiency mode for handset applications. For linear Doherty operation, we analyze the gain modulation as well as the cancellation of the third-order intermodulation distortion in order to improve the linearity. A compact design method is also discussed to implement on a single chip for a handset. The proposed Doherty PA delivers good performance with regard to the third-generation (3G)/fourth-generation (4G) modulation signals. A switched-load power-mode PA is adopted in the proposed Doherty PA to enhance the efficiency in the low-power region with over 10-dB back-off. For demonstration purposes, the PA is implemented using an InGaP/GaAs heterojunction bipolar transistor and AlGaAs/InGaAs pseudomorphic high electron-mobility transistor process. The PA is tested at 1.85 GHz using both a long-term evolution signal with 16-quadrature amplitude modulation, 7.5-dB peak-to-average power ratio, and 10-MHz bandwidth (BW) and a wideband code division multiple access signal with 3.3-dB PAPR and 3.84-MHz BW. The proposed linear Doherty PA with an enhanced back-off efficiency mode delivers good performance in both the high- and low-power modes, implying that the dual-power-mode Doherty PA configuration can be a promising candidate for extending the battery life of handheld devices in 3G and 4G wireless communication systems.
- 22 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 62 (3) , 567-578
Linear Doherty Power Amplifier With an Enhanced Back-Off Efficiency Mode for Handset Applications
This paper presents a linear Doherty power amplifier (PA) with enhanced back-off efficiency mode for handset applications. For linear Doherty operation, we analyze the gain modulation as well as the cancellation of the third-order intermodulation distortion in order to improve the linearity. A compact design method is also discussed to implement on a single chip for a handset. The proposed Doherty PA delivers good performance with regard to the third-generation (3G)/fourth-generation (4G) modulation signals. A switched-load power-mode PA is adopted in the proposed Doherty PA to enhance the efficiency in the low-power region with over 10-dB back-off. For demonstration purposes, the PA is implemented using an InGaP/GaAs heterojunction bipolar transistor and AlGaAs/InGaAs pseudomorphic high electron-mobility transistor process. The PA is tested at 1.85 GHz using both a long-term evolution signal with 16-quadrature amplitude modulation, 7.5-dB peak-to-average power ratio, and 10-MHz bandwidth (BW) and a wideband code division multiple access signal with 3.3-dB PAPR and 3.84-MHz BW. The proposed linear Doherty PA with an enhanced back-off efficiency mode delivers good performance in both the high- and low-power modes, implying that the dual-power-mode Doherty PA configuration can be a promising candidate for extending the battery life of handheld devices in 3G and 4G wireless communication systems.