Junxian Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Junxian Zhao has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Zhan Wang
State Key Laboratory of Subtropical Building Science South China University of Technology Guangzhou China
2 shared publications- Bin Wu
School of Civil Engineering, Harbin Institute of Technology, Harbin 150090, China
1 shared publication Bo Wu
1 shared publicationChaohai Guo
Graduate Student, School of Civil Engineering and Transportation, South China Univ. of Technology, Guangzhou 510641, China
1 shared publicationFuxiong Lin
Xiamen BIAD Architecture Design Co., LTD Xiamen 361009 China
1 shared publicationGuiqiang Hao
Zhongtu International Architectural Design Co., Ltd, Shijiazhuang, China
1 shared publication
Latest Publications
- 1 October 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 150 (10)
Bidirectional Cyclic Loading Performance of a Prefabricated Self-Centering Metallic-Damped Steel Column Base
- 1 October 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 150 (10)
Bidirectional Cyclic Loading Performance of a Prefabricated Self-Centering Metallic-Damped Steel Column Base
- 9 January 2019
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 28 (5)
Effect of gusset connection configurations on frame–gusset interaction in steel buckling‐restrained braced frame
Summary: Although buckling restrained braces (BRBs) are commonly applied in seismic buildings to mitigate structural damage, their performance was often limited by rupture of the corner gusset connections due to additional frame action. This issue may be resolved by alternative gusset connections to mitigate the frame–gusset interaction. In this study, commonly used procedures for design of the traditional gusset connection are reviewed, followed by a case study on the effect of frame action on the structural behavior of these gusset connections in steel frames with BRBs. Inspired by these analysis, two different strategies, aiming at releasing frame–gusset shear interaction using sliding gusset connection or reducing normal interaction using dual gusset plates, are tried to mitigate the frame action effects. Finite element analysis is conducted on steel frame subassemblages with/without BRBs to examine the effect of different gusset connections on the structural behavior of these framing systems. It shows that the sliding gusset connection shows beneficial effect in reducing the frame action, having much smaller stress responses on the gusset interfaces, as well as smaller shear force and plastic responses on the framing system. Thus, it becomes a promising gusset connection for improved seismic performance of the steel framing system with brace‐type dampers.
- 9 January 2019
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 28 (5)
Effect of gusset connection configurations on frame–gusset interaction in steel buckling‐restrained braced frame
Summary: Although buckling restrained braces (BRBs) are commonly applied in seismic buildings to mitigate structural damage, their performance was often limited by rupture of the corner gusset connections due to additional frame action. This issue may be resolved by alternative gusset connections to mitigate the frame–gusset interaction. In this study, commonly used procedures for design of the traditional gusset connection are reviewed, followed by a case study on the effect of frame action on the structural behavior of these gusset connections in steel frames with BRBs. Inspired by these analysis, two different strategies, aiming at releasing frame–gusset shear interaction using sliding gusset connection or reducing normal interaction using dual gusset plates, are tried to mitigate the frame action effects. Finite element analysis is conducted on steel frame subassemblages with/without BRBs to examine the effect of different gusset connections on the structural behavior of these framing systems. It shows that the sliding gusset connection shows beneficial effect in reducing the frame action, having much smaller stress responses on the gusset interfaces, as well as smaller shear force and plastic responses on the framing system. Thus, it becomes a promising gusset connection for improved seismic performance of the steel framing system with brace‐type dampers.
- 1 October 2018
- Published by Elsevier in Construction and Building Materials
- Vol. 187, 773-790
Creep behavior of thin-walled circular steel tubular columns filled with demolished concrete lumps and fresh concrete
- 1 October 2018
- Published by Elsevier in Construction and Building Materials
- Vol. 187, 773-790
Creep behavior of thin-walled circular steel tubular columns filled with demolished concrete lumps and fresh concrete
- 14 June 2018
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 16 (11) , 5591-5619
A novel non-iterative direct displacement-based seismic design procedure for self-centering buckling-restrained braced frame structures
- 14 June 2018
- Published by Springer Nature in Bulletin of Earthquake Engineering
- Vol. 16 (11) , 5591-5619
A novel non-iterative direct displacement-based seismic design procedure for self-centering buckling-restrained braced frame structures
- 29 September 2015
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 45 (3) , 359-381
Effect of non‐moment braced frame seismic deformations on buckling‐restrained brace end connection behavior: Theoretical analysis and subassemblage tests
Summary: In‐plane buckling‐restrained brace (BRB) end rotation induced by frame action is a commonly observed phenomenon in buckling‐restrained braced frames (BRBFs). However, its effect on BRB end connection behavior has not yet been clear. In this study, four BRB end deformation modes for quick determination of end rotational demand are proposed for non‐moment BRBF considering different BRB arrangements, installing story of BRBs, and boundary condition of corner gussets connected with column base. Key factors affecting BRB end rotation and flexural moments are examined theoretically by parametric analysis. Subassemblage tests of seven BRB specimens under horizontal cyclic loading were conducted by adopting two loading frames to impose the expected BRB end deformations. It shows that BRB end rotation subjected BRB ends to significant flexural moments, leading to premature yielding of BRB ends or even tendency of end zone buckling. The deformation modes, the flexural rigidity of BRB ends, and the initial geometric imperfections of BRBs were found to have significant influence on BRB end connection behavior. The triggering moment induced by BRB end rotation was the main contributor to end flexural moment. However, the moment amplification effect induced by flexure of BRB end zones became prominent especially for small flexural rigidity of BRB ends. Implications and future research needs for design of BRB end connections are provided finally based on the theoretical and experimental results. Copyright © 2015 John Wiley & Sons, Ltd.
- 29 September 2015
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 45 (3) , 359-381
Effect of non‐moment braced frame seismic deformations on buckling‐restrained brace end connection behavior: Theoretical analysis and subassemblage tests
Summary: In‐plane buckling‐restrained brace (BRB) end rotation induced by frame action is a commonly observed phenomenon in buckling‐restrained braced frames (BRBFs). However, its effect on BRB end connection behavior has not yet been clear. In this study, four BRB end deformation modes for quick determination of end rotational demand are proposed for non‐moment BRBF considering different BRB arrangements, installing story of BRBs, and boundary condition of corner gussets connected with column base. Key factors affecting BRB end rotation and flexural moments are examined theoretically by parametric analysis. Subassemblage tests of seven BRB specimens under horizontal cyclic loading were conducted by adopting two loading frames to impose the expected BRB end deformations. It shows that BRB end rotation subjected BRB ends to significant flexural moments, leading to premature yielding of BRB ends or even tendency of end zone buckling. The deformation modes, the flexural rigidity of BRB ends, and the initial geometric imperfections of BRBs were found to have significant influence on BRB end connection behavior. The triggering moment induced by BRB end rotation was the main contributor to end flexural moment. However, the moment amplification effect induced by flexure of BRB end zones became prominent especially for small flexural rigidity of BRB ends. Implications and future research needs for design of BRB end connections are provided finally based on the theoretical and experimental results. Copyright © 2015 John Wiley & Sons, Ltd.
- 1 November 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 138 (11) , 1398-1415
Flexural Demand on Pin-Connected Buckling-Restrained Braces and Design Recommendations
In a previous study by the authors, the cyclic behavior of a novel type of pin-connected angle steel buckling-restrained brace (ABRB) was examined, and the failure mechanism in the core projection of the ABRB induced by an excessive bending effect caused by end rotation was discussed. In this paper, the occurrence mechanism of end rotation modes and the bending effect in the core projection of an ABRB are first investigated based on the previous test results, which shows that end rotation demands would be significantly increased with the presence of a gap and an additional bending effect could be observed if the end rotation demands were large enough to cause two-point contact at the core ends. Then, a new method to predict the flexural demand on pin-connected BRBs is proposed by considering the effect of the end rotation modes, clearance, initial eccentricity, and initial deflection of casing. The design criteria to prevent yielding of the core projection are presented and further verified by the...
- 1 November 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 138 (11) , 1398-1415
Flexural Demand on Pin-Connected Buckling-Restrained Braces and Design Recommendations
In a previous study by the authors, the cyclic behavior of a novel type of pin-connected angle steel buckling-restrained brace (ABRB) was examined, and the failure mechanism in the core projection of the ABRB induced by an excessive bending effect caused by end rotation was discussed. In this paper, the occurrence mechanism of end rotation modes and the bending effect in the core projection of an ABRB are first investigated based on the previous test results, which shows that end rotation demands would be significantly increased with the presence of a gap and an additional bending effect could be observed if the end rotation demands were large enough to cause two-point contact at the core ends. Then, a new method to predict the flexural demand on pin-connected BRBs is proposed by considering the effect of the end rotation modes, clearance, initial eccentricity, and initial deflection of casing. The design criteria to prevent yielding of the core projection are presented and further verified by the...