Martin Hochberg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Martin Hochberg has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Martin Sack
Institute for Pulsed Power and Microwave Technology (IHM), Karlsruhe Institute of Technology, Karlsruhe, Germany
4 shared publications- Georg Mueller
Karlsruhe Institute of Technology, Institute for Pulsed Power and Microwave Technology, Karlsruhe, Germany
3 shared publications Alfons Weisenburger
2 shared publicationsDennis Herzog
2 shared publications- Aude Silve
Institute for Pulsed Power and Microwave Technology (IHM), Karlsruhe Institute of Technology, Karlsruhe, Germany
1 shared publication - Biniam Kebede
Department of Food Science, University of Guelph, Guelph, Canada
1 shared publication
Latest Publications
- 9 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (9) , 2670-2680
Conception and Development of a Pulsed Microwave Applicator for Exposure of Fresh Microalgae Biomass
This study presents the conception and development of a microwave (MW) applicator based on a TM010 cavity and a pulsed MW source, both custom-designed for evaluation of MW disruption of microalgae. The objective is the selective heating of microalgae immersed in their environment. The applicator enables exposing microalgae suspension to MW in continuous flow mode and monitoring the energy absorbed by the sample. The design was based on dielectric characteristics of microalgae in water, but other solvents might be considered. A tuning element ensures efficient MW coupling into the samples whose relative permittivity ranges from 10 to 80. The applicator includes a customized power supply operating a commercial magnetron source in pulse mode. The MW pulses are in the range of multiple kilowatts with adjustable duration in the microseconds range. The applicator enables to reach a power density in the microalgae sample beyond 10 10 W/m 3 . Preliminary proof-of-principle experiments of MW disruption on fresh microalgae biomass Auxenochlorella protothecoides followed by lipid extraction enabled almost complete lipid recovery, while yields were negligible on untreated samples. Total energy consumption was below 4.2 MJ per kg of dry microalgae. Finally, the applicator characteristics are promising for future upscaling and deployment in the industry.
- 9 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (9) , 2670-2680
Conception and Development of a Pulsed Microwave Applicator for Exposure of Fresh Microalgae Biomass
This study presents the conception and development of a microwave (MW) applicator based on a TM010 cavity and a pulsed MW source, both custom-designed for evaluation of MW disruption of microalgae. The objective is the selective heating of microalgae immersed in their environment. The applicator enables exposing microalgae suspension to MW in continuous flow mode and monitoring the energy absorbed by the sample. The design was based on dielectric characteristics of microalgae in water, but other solvents might be considered. A tuning element ensures efficient MW coupling into the samples whose relative permittivity ranges from 10 to 80. The applicator includes a customized power supply operating a commercial magnetron source in pulse mode. The MW pulses are in the range of multiple kilowatts with adjustable duration in the microseconds range. The applicator enables to reach a power density in the microalgae sample beyond 10 10 W/m 3 . Preliminary proof-of-principle experiments of MW disruption on fresh microalgae biomass Auxenochlorella protothecoides followed by lipid extraction enabled almost complete lipid recovery, while yields were negligible on untreated samples. Total energy consumption was below 4.2 MJ per kg of dry microalgae. Finally, the applicator characteristics are promising for future upscaling and deployment in the industry.
- Open Access
Evolution of Volatile and Phenolic Compounds during Bottle Storage of Merlot Wines Vinified Using Pulsed Electric Fields-Treated Grapes
This study aimed to elucidate changes in volatile, phenolic, and oenological profiles of wines vinified from Pulsed Electric Fields (PEF)-treated and untreated Merlot grapes during bottle storage of up to 150, 90, and 56 days at 4 °C, 25 °C, and 45 °C, respectively, through chemometrics technique. Wines produced from untreated grapes and those PEF-treated at four different processing conditions (electric field strength 33.1 and 41.5 kV/cm and energy inputs between 16.5 and 49.4 kJ/kg) were used for the bottle storage study. Results showed that hydroxycinnamic and hydroxybenzoic acids in all stored wines, regardless vinified from untreated and PEF-treated grapes, increased as a function of time and temperature, while anthocyanins and selected esters (e.g., ethyl butanoate) decreased. Extreme storage temperature, at 45 °C particularly, resulted in a higher amount of linalool-3, 7-oxide in all stored wines. After prolonged storage, all wines produced from grapes PEF-treated with four different processing conditions were shown to favor high retention of phenolics after storage but induced faster reduction of anthocyanins when compared to wines produced from untreated grapes. Moreover, some volatiles in wines vinified using PEF-treated grapes, such as citronellol and 2-phenylethyl acetate, were found to be less susceptible towards degradation during prolonged storage. Production of furans was generally lower in most stored wines, particularly those produced from PEF-treated grapes at higher energy inputs (>47 kJ/kg). Overall, PEF pre-treatment on grapes may improve storage and temperature stability of the obtained wines.
Open AccessEvolution of Volatile and Phenolic Compounds during Bottle Storage of Merlot Wines Vinified Using Pulsed Electric Fields-Treated Grapes
This study aimed to elucidate changes in volatile, phenolic, and oenological profiles of wines vinified from Pulsed Electric Fields (PEF)-treated and untreated Merlot grapes during bottle storage of up to 150, 90, and 56 days at 4 °C, 25 °C, and 45 °C, respectively, through chemometrics technique. Wines produced from untreated grapes and those PEF-treated at four different processing conditions (electric field strength 33.1 and 41.5 kV/cm and energy inputs between 16.5 and 49.4 kJ/kg) were used for the bottle storage study. Results showed that hydroxycinnamic and hydroxybenzoic acids in all stored wines, regardless vinified from untreated and PEF-treated grapes, increased as a function of time and temperature, while anthocyanins and selected esters (e.g., ethyl butanoate) decreased. Extreme storage temperature, at 45 °C particularly, resulted in a higher amount of linalool-3, 7-oxide in all stored wines. After prolonged storage, all wines produced from grapes PEF-treated with four different processing conditions were shown to favor high retention of phenolics after storage but induced faster reduction of anthocyanins when compared to wines produced from untreated grapes. Moreover, some volatiles in wines vinified using PEF-treated grapes, such as citronellol and 2-phenylethyl acetate, were found to be less susceptible towards degradation during prolonged storage. Production of furans was generally lower in most stored wines, particularly those produced from PEF-treated grapes at higher energy inputs (>47 kJ/kg). Overall, PEF pre-treatment on grapes may improve storage and temperature stability of the obtained wines.
- 31 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (1) , 627-634
A Fast Modular Semiconductor-Based Marx Generator for Driving Dynamic Loads
- 31 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (1) , 627-634
A Fast Modular Semiconductor-Based Marx Generator for Driving Dynamic Loads
- 3 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (10) , 3284-3290
Design Validation of a Single Semiconductor-Based Marx-Generator Stage for Fast Step-Wise Arbitrary Output Waveforms
A new modular pulsed-power source with fast rise time and step-wise arbitrary output waveform generation is currently under development to drive the Gepulste Elektronenstrahlanlage device investigated at the Institute for Pulsed Power and Microwave Technology (IHM). Acknowledging the complex design procedures necessary to set up a modular pulsed-power source for voltages of up to 120 kV, this paper focuses on the circuit design for a single stage and its validation prior to the generator assembly. Using a semiconductor-based Marx generator topology, the stages are designed to have an output voltage of 1 kV with a pulse current of up to 600 A. When connected to an ohmic load, the measured current rise times are in the order of 46 ns resulting in the current rise rates of up to 10 kA/μs using the commercial devices. The step-wise arbitrary output waveform is created by generating the switching commands on the stage using a microprocessor and a fast optical synchronization unit. Effective stage shielding is verified by operating the stage in a 100-kV, 2.5-kA electromagnetic interference test bed. This paper presents the design considerations and the corresponding measurements.
- 3 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (10) , 3284-3290
Design Validation of a Single Semiconductor-Based Marx-Generator Stage for Fast Step-Wise Arbitrary Output Waveforms
A new modular pulsed-power source with fast rise time and step-wise arbitrary output waveform generation is currently under development to drive the Gepulste Elektronenstrahlanlage device investigated at the Institute for Pulsed Power and Microwave Technology (IHM). Acknowledging the complex design procedures necessary to set up a modular pulsed-power source for voltages of up to 120 kV, this paper focuses on the circuit design for a single stage and its validation prior to the generator assembly. Using a semiconductor-based Marx generator topology, the stages are designed to have an output voltage of 1 kV with a pulse current of up to 600 A. When connected to an ohmic load, the measured current rise times are in the order of 46 ns resulting in the current rise rates of up to 10 kA/μs using the commercial devices. The step-wise arbitrary output waveform is created by generating the switching commands on the stage using a microprocessor and a fast optical synchronization unit. Effective stage shielding is verified by operating the stage in a 100-kV, 2.5-kA electromagnetic interference test bed. This paper presents the design considerations and the corresponding measurements.
- 14 July 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 44 (10) , 2030-2034
A Test Environment for Power Semiconductor Devices Using a Gate-Boosting Circuit
For semiconductor-based pulsed power generators, short turn-ON and turn-OFF times of the employed switching elements are especially in hard switching condition of advantage. In order to enhance switching speeds for standard devices under hard switching conditions, we propose a capacitively coupled gate-boosting circuit with gate-drive voltages of up to 80 V. A low inductance test circuit has been set up to evaluate different switching elements under varying driving conditions. Beside single pulse operation, the setup allows for burst mode and continuous repetitive switching. The flexible design of the setup allows for testing metal-oxide-semiconductor field-effect transistors (MOSFETs) as well as insulated-gate bipolar transistors (IGBTs). Exemplary, we show results for a SiC MOSFET and a standard IGBT. By applying 80 V gate-drive voltage, the current rise rate of the SiC MOSFET could be increased by a factor of 3.5 up to 2.6 kA/μs. For standard IGBT devices, we achieved an eightfold increase in current rise rate up to 4.2 kA/μs. We verified a reproducible pulse shape for over 10 8 pulses. In addition, the gate-drive circuit is able to drive the device in 3-MHz burst mode at 250 A peak collector current.
- 14 July 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 44 (10) , 2030-2034
A Test Environment for Power Semiconductor Devices Using a Gate-Boosting Circuit
For semiconductor-based pulsed power generators, short turn-ON and turn-OFF times of the employed switching elements are especially in hard switching condition of advantage. In order to enhance switching speeds for standard devices under hard switching conditions, we propose a capacitively coupled gate-boosting circuit with gate-drive voltages of up to 80 V. A low inductance test circuit has been set up to evaluate different switching elements under varying driving conditions. Beside single pulse operation, the setup allows for burst mode and continuous repetitive switching. The flexible design of the setup allows for testing metal-oxide-semiconductor field-effect transistors (MOSFETs) as well as insulated-gate bipolar transistors (IGBTs). Exemplary, we show results for a SiC MOSFET and a standard IGBT. By applying 80 V gate-drive voltage, the current rise rate of the SiC MOSFET could be increased by a factor of 3.5 up to 2.6 kA/μs. For standard IGBT devices, we achieved an eightfold increase in current rise rate up to 4.2 kA/μs. We verified a reproducible pulse shape for over 10 8 pulses. In addition, the gate-drive circuit is able to drive the device in 3-MHz burst mode at 250 A peak collector current.