Angelika Kmita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Angelika Kmita has a total of 203 co-authors. Here are the top co-authors by number of shared publications:
- Dorota Lachowicz
Academic Centre for Materials and Nanotechnology, AGH University of Krakow, A. Mickiewicza 30, 30-059 Krakow, Poland
11 shared publications - Mariusz Holtzer
Faculty of Foundry Engineering, AGH University of Krakow, A. Mickiewicza 30 St., 30-059 Krakow, Poland
9 shared publications - Marcin Sikora
National Synchrotron Radiation Centre SOLARIS, Jagiellonian University, Czerwone Maki 98, PL-30392 Kraków, Poland
8 shared publications Marta Gajewska
AGH University of Science and Technology, Academic Centre for Materials and Nanotechnology, Al. A. Mickiewicza 30, 30-059 Krakow, Poland
8 shared publications- Rafał Dańko
Faculty of Foundry Engineering, AGH University of Krakow, A. Mickiewicza 30 St., 30-059 Krakow, Poland
8 shared publications Mariusz Holtzer
6 shared publications
Latest Publications
- Open Access
Comparative Study of Spent Sand Reclamation from Binder Jetting and Conventional Foundry Technologies
The growing use of binder jetting in foundry practice has increased the need for effective recovery of the fine silica sand used in additively manufactured molds. This study examines mechanical and thermal reclamation of spent furfuryl-resin sands obtained from binder-jetted molds (US-1) and conventionally manufactured molds (US-2) after ductile iron casting. Mechanical reclamation was conducted at rotor speeds of 280–560 rpm for 10–30 min, whereas thermal reclamation was performed at nominal temperatures of 600–1000 °C. Reclaim quality was assessed using loss on ignition (LOI), pH, collected dust content, and bending strength, with grain morphology used to support the interpretation of the results. At 560 rpm for 30 min, the mechanical-reclamation efficiency index (WRK) reached 31.5% for US-1 and 41.1% for US-2. At the highest nominal thermal-reclamation temperature after 30 min, LOI reached 0.14% and 0.29%, respectively. These results characterize each sand under the treatment and separation conditions applied to it. Different air-classification velocities—0.75 m/s for US-1 and 1.0 m/s for US-2—limit direct comparisons of collected dust, retained-matrix LOI, and the derived WRK values. Together with differences in the initial sand characteristics, these classification conditions prevent differences between the systems from being attributed solely to the mold-manufacturing technology. Within each tested system, thermal reclamation achieved lower residual LOI, although selecting a process for practical use also requires an assessment of grain integrity and reuse performance.
Open AccessComparative Study of Spent Sand Reclamation from Binder Jetting and Conventional Foundry Technologies
The growing use of binder jetting in foundry practice has increased the need for effective recovery of the fine silica sand used in additively manufactured molds. This study examines mechanical and thermal reclamation of spent furfuryl-resin sands obtained from binder-jetted molds (US-1) and conventionally manufactured molds (US-2) after ductile iron casting. Mechanical reclamation was conducted at rotor speeds of 280–560 rpm for 10–30 min, whereas thermal reclamation was performed at nominal temperatures of 600–1000 °C. Reclaim quality was assessed using loss on ignition (LOI), pH, collected dust content, and bending strength, with grain morphology used to support the interpretation of the results. At 560 rpm for 30 min, the mechanical-reclamation efficiency index (WRK) reached 31.5% for US-1 and 41.1% for US-2. At the highest nominal thermal-reclamation temperature after 30 min, LOI reached 0.14% and 0.29%, respectively. These results characterize each sand under the treatment and separation conditions applied to it. Different air-classification velocities—0.75 m/s for US-1 and 1.0 m/s for US-2—limit direct comparisons of collected dust, retained-matrix LOI, and the derived WRK values. Together with differences in the initial sand characteristics, these classification conditions prevent differences between the systems from being attributed solely to the mold-manufacturing technology. Within each tested system, thermal reclamation achieved lower residual LOI, although selecting a process for practical use also requires an assessment of grain integrity and reuse performance.
- Open Access
- 1 September 2026
- Published by MDPI AG in Preprints.org
Comparative Study of Spent Sand Reclamation from Binder Jetting and Conventional Foundry Technologies
The growing use of binder jetting in foundry practice creates a need for effective recovery of the fine silica sand used in additively manufactured molds. This study compares mechanical and thermal reclamation of spent furfuryl-resin sands originating from binder-jetted molds (US-1) and conventionally manufactured molds (US-2) after ductile iron casting. Mechanical reclamation was conducted at rotor speeds of 280–560 rpm for 10–30 min, whereas thermal reclamation was performed at 600–1000 °C. Reclaim quality was assessed using loss on ignition (LOI), pH, dust generation, grain morphology, and bending strength. Conventional spent sand was more susceptible to mechanical treatment, reaching a maximum reclamation efficiency index of 41.1%, compared with 31.5% for binder-jetted sand. Thermal treatment was markedly more effective, reducing LOI to 0.14% for US-1 and 0.29% for US-2 and increasing reclamation efficiency to 94.8% and 89.8%, respectively. High-temperature thermal reclamation is therefore particularly suitable for fine-grained binder-jetted sand, whereas excessive mechanical treatment may promote grain crushing and dust formation.
- 1 September 2026
- Published by MDPI AG in Preprints.org
Open AccessComparative Study of Spent Sand Reclamation from Binder Jetting and Conventional Foundry Technologies
The growing use of binder jetting in foundry practice creates a need for effective recovery of the fine silica sand used in additively manufactured molds. This study compares mechanical and thermal reclamation of spent furfuryl-resin sands originating from binder-jetted molds (US-1) and conventionally manufactured molds (US-2) after ductile iron casting. Mechanical reclamation was conducted at rotor speeds of 280–560 rpm for 10–30 min, whereas thermal reclamation was performed at 600–1000 °C. Reclaim quality was assessed using loss on ignition (LOI), pH, dust generation, grain morphology, and bending strength. Conventional spent sand was more susceptible to mechanical treatment, reaching a maximum reclamation efficiency index of 41.1%, compared with 31.5% for binder-jetted sand. Thermal treatment was markedly more effective, reducing LOI to 0.14% for US-1 and 0.29% for US-2 and increasing reclamation efficiency to 94.8% and 89.8%, respectively. High-temperature thermal reclamation is therefore particularly suitable for fine-grained binder-jetted sand, whereas excessive mechanical treatment may promote grain crushing and dust formation.
- Open Access
- 18 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 267
Synthesis of Ti45Zr38Ni17 quasicrystalline ribbons for conventional hydrogen storage
- 18 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 267
Open AccessSynthesis of Ti45Zr38Ni17 quasicrystalline ribbons for conventional hydrogen storage
- Open Access
- 23 July 2026
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 14 (5)
Scalable magnetic biochar-based thin films for efficient multi-contaminant water remediation: Overcoming the limitations of powdered adsorbents
- 23 July 2026
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 14 (5)
Open AccessScalable magnetic biochar-based thin films for efficient multi-contaminant water remediation: Overcoming the limitations of powdered adsorbents
- Open Access
- 21 May 2026
- Published by Elsevier in SSRN Electronic Journal
Synthesis of Ti45Zr38Ni17 quasicrystalline ribbons for conventional hydrogen storage
Metastable amorphous or quasicrystalline materials are very intriguing regarding hydrogen storage by gaseous or electrochemical means. In this contribution, we report the results of studies on the formation of the Ti45Zr38Ni17 icosahedral ribbons prepared by the melt spinning method. It is evidenced that quasicrystalline specimens of high quality can be obtained for a moderate spinning speed of 30 m s-1. Measurements of the hydrogen storage capacity for the gaseous phase yielded the maximum hydrogen concentration for the powdered ribbons equal to 2.60 wt.% at 20°C. The article examines the influence of temperature on hydrogen storage in quasicrystals.
- 21 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynthesis of Ti45Zr38Ni17 quasicrystalline ribbons for conventional hydrogen storage
Metastable amorphous or quasicrystalline materials are very intriguing regarding hydrogen storage by gaseous or electrochemical means. In this contribution, we report the results of studies on the formation of the Ti45Zr38Ni17 icosahedral ribbons prepared by the melt spinning method. It is evidenced that quasicrystalline specimens of high quality can be obtained for a moderate spinning speed of 30 m s-1. Measurements of the hydrogen storage capacity for the gaseous phase yielded the maximum hydrogen concentration for the powdered ribbons equal to 2.60 wt.% at 20°C. The article examines the influence of temperature on hydrogen storage in quasicrystals.
- Open Access
- 16 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (5) , 4157-4169
Nuclear relaxation in agar gel in the presence of highly concentrated PEG coated magnetic nanoparticles at low magnetic fields. Application of temperature dependent weighting for MRI thermometry
Magnetic nanoparticles are used to map the temperature of the human body using MRI because their presence influences proton relaxation times. Especially at low fields, proton relaxation times exhibit strong temperature dependence, enabling precise determination of local temperature within a body with high resolution. As an illustration, we report temperature-dependent NMR and MRI investigations of agar gel with embedded Mn0.48Zn0.46Fe2.06O4 ferrite nanoparticles, evaluated as potential temperature–sensitive exogenous MRI contrast agents at low magnetic fields for noninvasive MRI thermometry. The nanoparticles consisted of an 8.5 nm magnetic core that were coated with a PEG shell, yielding a hydrodynamic diameter of 20 nm. Spin-lattice relaxation time (T1) profiles were obtained using a Fast Field Cycling NMR relaxometer. The – weighted gradient echo MR images at 0.2 T were obtained in a temperature range of 23 °C to 50.5 °C, encompassing physiologically relevant values. Simulations of MR image intensity at 0.2 T, based on experimental T1 and values, were carried out and compared with the corresponding temperature-dependent experimental images. Analysis of our measurements indicated that the temperature was determined with 2 °C accuracy.
- 16 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (5) , 4157-4169
Open AccessNuclear relaxation in agar gel in the presence of highly concentrated PEG coated magnetic nanoparticles at low magnetic fields. Application of temperature dependent weighting for MRI thermometry
Magnetic nanoparticles are used to map the temperature of the human body using MRI because their presence influences proton relaxation times. Especially at low fields, proton relaxation times exhibit strong temperature dependence, enabling precise determination of local temperature within a body with high resolution. As an illustration, we report temperature-dependent NMR and MRI investigations of agar gel with embedded Mn0.48Zn0.46Fe2.06O4 ferrite nanoparticles, evaluated as potential temperature–sensitive exogenous MRI contrast agents at low magnetic fields for noninvasive MRI thermometry. The nanoparticles consisted of an 8.5 nm magnetic core that were coated with a PEG shell, yielding a hydrodynamic diameter of 20 nm. Spin-lattice relaxation time (T1) profiles were obtained using a Fast Field Cycling NMR relaxometer. The – weighted gradient echo MR images at 0.2 T were obtained in a temperature range of 23 °C to 50.5 °C, encompassing physiologically relevant values. Simulations of MR image intensity at 0.2 T, based on experimental T1 and values, were carried out and compared with the corresponding temperature-dependent experimental images. Analysis of our measurements indicated that the temperature was determined with 2 °C accuracy.
- 21 August 2025
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 630
Influence of particle shape on magnetic behavior of SrFe12O19/CoxFey composites
- 21 August 2025
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 630
Influence of particle shape on magnetic behavior of SrFe12O19/CoxFey composites
- Open Access
- 21 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (33) , 17300-17312
Enhancing the reversibility of thermochromism of polydiacetylene-based nanostructures embedded in a natural polymer matrix
Reversible thermochromism in polydiacetylene nanosheets is enhanced via amide-functionalization and embedding in alginate, yielding stable, responsive nanocomposites with up to 70% color recovery for sensing and smart material applications.
- 21 August 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (33) , 17300-17312
Open AccessEnhancing the reversibility of thermochromism of polydiacetylene-based nanostructures embedded in a natural polymer matrix
Reversible thermochromism in polydiacetylene nanosheets is enhanced via amide-functionalization and embedding in alginate, yielding stable, responsive nanocomposites with up to 70% color recovery for sensing and smart material applications.