Meral Akkoyun Kurtlu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Meral Akkoyun Kurtlu has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Sibel Tuna
Bursa Technical University
8 shared publications- Sibel Tuna
Bursa Teknik Üniversitesi
4 shared publications - Ahmet Öztürk
Bursa Technical University, Metallurgical and Materials Engineering Department
1 shared publication Beril Tuncay
Department of Polymer Materials Engineering, Bursa Technical University, Bursa, Turkey
1 shared publicationBuse Fem
1 shared publication- Didem Ovalı
Osmaniye Korkut Ata Üniversitesi
1 shared publication
Latest Publications
- 27 March 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 39 (11) , 6182-6207
Improved thermal conductivity, mechanical, and flammability properties of polypropylene/hexagonal boron nitride/silicon carbide nanocomposites using a titanate-based coupling agent
An increasing demand persists for advanced materials such as polymer nanocomposites with improved thermal and mechanical properties while preserving their electrical insulation. Accordingly, hexagonal boron nitride (hBN) and silicon carbide (SiC) reinforced polypropylene (PP) nanocomposites were prepared both with and without the use of a titanate (Ti)-based coupling agent. The influence of the filler content and the use of a compatibilizing agent on the final properties were investigated. PP/hBN/SiC and PP/Ti-hBN/Ti-SiC hybrid polymer nanocomposites reinforced at various filler contents (20 wt.%, 40 wt.%, and 50 wt.%) were produced using mechanical mixing and compression molding methods. As the filler content increased, the elastic modulus of PP improved by 57%, and mechanical strength was notably enhanced. The use of Ti was found to promote a more homogeneous distribution of the fillers, improving flexibility and impact resistance. Thermal analyses showed that the fillers improved the thermal properties of PP, while excessively high filler contents could lead to adverse effects. The thermal conductivity increased by 216% for the 20 wt.% hBN/SiC-filled samples compared to pure PP, and this increase reached 248% for the titanate-treated samples. These results highlight the potential of PP-based nanocomposites for industrial applications and emphasize the need for optimization.
- 27 March 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 39 (11) , 6182-6207
Improved thermal conductivity, mechanical, and flammability properties of polypropylene/hexagonal boron nitride/silicon carbide nanocomposites using a titanate-based coupling agent
An increasing demand persists for advanced materials such as polymer nanocomposites with improved thermal and mechanical properties while preserving their electrical insulation. Accordingly, hexagonal boron nitride (hBN) and silicon carbide (SiC) reinforced polypropylene (PP) nanocomposites were prepared both with and without the use of a titanate (Ti)-based coupling agent. The influence of the filler content and the use of a compatibilizing agent on the final properties were investigated. PP/hBN/SiC and PP/Ti-hBN/Ti-SiC hybrid polymer nanocomposites reinforced at various filler contents (20 wt.%, 40 wt.%, and 50 wt.%) were produced using mechanical mixing and compression molding methods. As the filler content increased, the elastic modulus of PP improved by 57%, and mechanical strength was notably enhanced. The use of Ti was found to promote a more homogeneous distribution of the fillers, improving flexibility and impact resistance. Thermal analyses showed that the fillers improved the thermal properties of PP, while excessively high filler contents could lead to adverse effects. The thermal conductivity increased by 216% for the 20 wt.% hBN/SiC-filled samples compared to pure PP, and this increase reached 248% for the titanate-treated samples. These results highlight the potential of PP-based nanocomposites for industrial applications and emphasize the need for optimization.
- Open Access
- 16 January 2026
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 16 (1) , 63-74
Effect of Titanate-Based Compatibilizing Agent Coated Walnut Shell Powder on Rigid Polyurethane Foam Composites
This study aimed to obtain less costly and environmentally friendly polyurethane foam by reducing the petroleum-based chemicals used in the production of rigid polyurethane foam in the industry by adding walnut shell particles compatibilized with titanate as a filler. In this work, after a titanate-based compatibilization of walnut shell particles (Ti-WS), rigid polyurethane (PU) foam composites filled at different Ti-WS weight ratios (1 wt.%, 5 wt.%, 10 wt.%, and 15 wt.%) were produced. Walnut shells used as fillers were first powdered and then compatibilized with titanate-based agent. Afterwards, the polyol and filler were mixed using an ultrasonic homogenizer, isocyanate was added, and the mixture was poured into the mold to finally obtain the polyurethane foam composite. The produced samples were subjected to chemical, microstructure and thermal analyses. From the results, no chemical interaction of the filler with the matrix structure was observed, and the small changes in peak intensities were due to intermolecular interactions occurring at the filler-matrix interface. In addition, it was seen that PU foam composites showed an improvement of the thermal conductivity with the augmentation of Ti-WS weight ratio and Ti-WS15 foam composite exhibited the higher thermal conductivity of 0.09454 W/m.K compared to the pure PU foam (0.02398 W/m.K) with an increase of 394%. Furthermore, as expected an increase of the filler content resulted in a reduction of the mean cell size of the foam up to 180 µm. Thanks to these improved properties, it can be stated that the use of walnut shell as a natural filler in PU foam composites can promote a new application path in converting agricultural waste into useful resources for creating a new class of green materials.
- 16 January 2026
- Published by Karadeniz Fen Bilimleri Dergisi in Karadeniz Fen Bilimleri Dergisi
- Vol. 16 (1) , 63-74
Open AccessEffect of Titanate-Based Compatibilizing Agent Coated Walnut Shell Powder on Rigid Polyurethane Foam Composites
This study aimed to obtain less costly and environmentally friendly polyurethane foam by reducing the petroleum-based chemicals used in the production of rigid polyurethane foam in the industry by adding walnut shell particles compatibilized with titanate as a filler. In this work, after a titanate-based compatibilization of walnut shell particles (Ti-WS), rigid polyurethane (PU) foam composites filled at different Ti-WS weight ratios (1 wt.%, 5 wt.%, 10 wt.%, and 15 wt.%) were produced. Walnut shells used as fillers were first powdered and then compatibilized with titanate-based agent. Afterwards, the polyol and filler were mixed using an ultrasonic homogenizer, isocyanate was added, and the mixture was poured into the mold to finally obtain the polyurethane foam composite. The produced samples were subjected to chemical, microstructure and thermal analyses. From the results, no chemical interaction of the filler with the matrix structure was observed, and the small changes in peak intensities were due to intermolecular interactions occurring at the filler-matrix interface. In addition, it was seen that PU foam composites showed an improvement of the thermal conductivity with the augmentation of Ti-WS weight ratio and Ti-WS15 foam composite exhibited the higher thermal conductivity of 0.09454 W/m.K compared to the pure PU foam (0.02398 W/m.K) with an increase of 394%. Furthermore, as expected an increase of the filler content resulted in a reduction of the mean cell size of the foam up to 180 µm. Thanks to these improved properties, it can be stated that the use of walnut shell as a natural filler in PU foam composites can promote a new application path in converting agricultural waste into useful resources for creating a new class of green materials.
- 1 November 2025
- Published by SAGE Publications in Cellular Polymers
- Vol. 44 (3-6) , 93-134
An overview of polymer foam technologies with a focus on polylactic acid, polypropylene, and polyamide 6-based materials
Polymer-based composite materials are widely used in a number of engineering applications owing to their light weight, mechanical strength, chemical resistance and versatility in design. Using these materials in foam form offers several additional advantages, including reduced density, improved heat and sound insulation, and increased impact resistance. In the contemporary era, intensive research is being conducted into the evaluation of petrochemical-based polymers, such as polypropylene (PP) and polyamide 6 (PA6), and biopolymers, particularly polylactic acid (PLA), in foamed composite structures. Furthermore, hybrid systems formed by the combination of these different polymer types offer great potential for balancing environmental sustainability and performance. This review discusses the general structure, foam formation mechanisms, production techniques and basic properties of polymer-based foam composite materials. Prominent polymer-based systems, such as PP, PA6 and PLA, were examined comparatively. Additionally, contemporary methodologies concerning hybrid foam systems formed by PLA with PP and PA6, as presented in the existing literature, were evaluated.
- 1 November 2025
- Published by SAGE Publications in Cellular Polymers
- Vol. 44 (3-6) , 93-134
An overview of polymer foam technologies with a focus on polylactic acid, polypropylene, and polyamide 6-based materials
Polymer-based composite materials are widely used in a number of engineering applications owing to their light weight, mechanical strength, chemical resistance and versatility in design. Using these materials in foam form offers several additional advantages, including reduced density, improved heat and sound insulation, and increased impact resistance. In the contemporary era, intensive research is being conducted into the evaluation of petrochemical-based polymers, such as polypropylene (PP) and polyamide 6 (PA6), and biopolymers, particularly polylactic acid (PLA), in foamed composite structures. Furthermore, hybrid systems formed by the combination of these different polymer types offer great potential for balancing environmental sustainability and performance. This review discusses the general structure, foam formation mechanisms, production techniques and basic properties of polymer-based foam composite materials. Prominent polymer-based systems, such as PP, PA6 and PLA, were examined comparatively. Additionally, contemporary methodologies concerning hybrid foam systems formed by PLA with PP and PA6, as presented in the existing literature, were evaluated.
- 21 September 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (2)
Synergistic Effect of Blast Furnace Slag and Fly Ash on the Properties of Polyamide 6
The use of waste products such as ground‐granulated blast furnace slag (BFS) and fly ash (FA) as fillers in polymer matrices is a relatively new approach. Polymer composites prepared with BFS and FA can be suitable candidates for applications requiring electrical insulation properties due to their improved mechanical properties, wear resistance, and thermal resistance, as well as their low electrical conductivity. The aim of this work is to investigate the synergistic effects of BFS and FA on the final structural, thermal, mechanical, morphological, and electrical conductivity properties of polyamide 6 (PA6), a thermoplastic polymer widely used in the plastic industry. When BFS/FA‐added PA6 composites prepared at ratios of 5, 10, 20, 30, and 40 wt.% using twin screw extruder and compression molding methods were characterized, the physical interactions were observed at the intermolecular level. A general decrease in tensile strength values with increasing BFS/FA content was obtained. BFS/FA particles were homogeneously dispersed in the PA6 matrix, but a weak interaction occurs at the filler–matrix interface. Concerning the electrical conductivity results, the use of BFS/FA fillers in PA6 composites improved the electrical conductivity values as intended, but the interfacial compatibility should be increased in applications requiring mechanical performance.
- 21 September 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (2)
Synergistic Effect of Blast Furnace Slag and Fly Ash on the Properties of Polyamide 6
The use of waste products such as ground‐granulated blast furnace slag (BFS) and fly ash (FA) as fillers in polymer matrices is a relatively new approach. Polymer composites prepared with BFS and FA can be suitable candidates for applications requiring electrical insulation properties due to their improved mechanical properties, wear resistance, and thermal resistance, as well as their low electrical conductivity. The aim of this work is to investigate the synergistic effects of BFS and FA on the final structural, thermal, mechanical, morphological, and electrical conductivity properties of polyamide 6 (PA6), a thermoplastic polymer widely used in the plastic industry. When BFS/FA‐added PA6 composites prepared at ratios of 5, 10, 20, 30, and 40 wt.% using twin screw extruder and compression molding methods were characterized, the physical interactions were observed at the intermolecular level. A general decrease in tensile strength values with increasing BFS/FA content was obtained. BFS/FA particles were homogeneously dispersed in the PA6 matrix, but a weak interaction occurs at the filler–matrix interface. Concerning the electrical conductivity results, the use of BFS/FA fillers in PA6 composites improved the electrical conductivity values as intended, but the interfacial compatibility should be increased in applications requiring mechanical performance.
- 28 August 2025
- Published by Wiley in Macromolecular Symposia
- Vol. 414 (4)
Effect of Barium Titanate on the Mechanical and Piezoelectric Performance of Natural Rubber‐Based Composites
The effects of barium titanate (BaTiO 3 ) filler on the rheology, mechanical, and piezoelectric properties of natural rubber (NR) based industrial rubber mixture were investigated. The results revealed lower time to reach 90% curing (tc90) and lower tensile strength and elongation at break values for BaTiO 3 ‐filled rubber composites compared to the pure rubber mixture. The piezoelectric charge constant ( d 33 ) and the generated voltage of BaTiO 3 ‐filled rubber composites increased up to 3 pC/N and 120 mV, respectively, for a total filler content of 40 vol.% with the increase of the filler content.
- 28 August 2025
- Published by Wiley in Macromolecular Symposia
- Vol. 414 (4)
Effect of Barium Titanate on the Mechanical and Piezoelectric Performance of Natural Rubber‐Based Composites
The effects of barium titanate (BaTiO 3 ) filler on the rheology, mechanical, and piezoelectric properties of natural rubber (NR) based industrial rubber mixture were investigated. The results revealed lower time to reach 90% curing (tc90) and lower tensile strength and elongation at break values for BaTiO 3 ‐filled rubber composites compared to the pure rubber mixture. The piezoelectric charge constant ( d 33 ) and the generated voltage of BaTiO 3 ‐filled rubber composites increased up to 3 pC/N and 120 mV, respectively, for a total filler content of 40 vol.% with the increase of the filler content.
- 25 August 2025
- Published by Springer Nature
- p. 31-65
Polylactic Acid and Its Blends for Biomedical Applications
- 25 August 2025
- Published by Springer Nature
- p. 31-65
Polylactic Acid and Its Blends for Biomedical Applications
- 26 June 2025
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 61 (4) , 245-263
On the use of olive leaf powder to improve the performance of water-blown rigid polyurethane foam composites
Nowadays, polyurethane (PU) foams were preferred in a broad extent of applications particularly due to their lowest thermal conductivity values satisfying the demand for energy efficiency while their use as natural filler added foam composites can reduce the polymer content allowing a more environmentally friendly production. The purpose of this work was to research the impact of olive leaf powder of various particle sizes and weight ratios on the microstructure, thermal, and mechanical properties of rigid polyurethane foam composites. All results exhibited optimum mechanical, thermal, and microstructure properties for the finest particle sized and 3 wt% added foam composites. This foam composite demonstrated an enhancement by 54%, 41%, and 61% for the tensile strength, elongation at break, and compression strength values, respectively. The thermal degradation temperature of the foam composites was also improved in correlation with the reduction of the glass transition temperature of the soft segments while the glass transition of the hard segments increased. Concerning the thermal conductivity results, the highest reduction by 11% was observed for the finest particles filled at 5 wt%, compared to the pure rigid PU foam, in correlation with the cell size showing a maximum reduction by 18% for the same composite.
- 26 June 2025
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 61 (4) , 245-263
On the use of olive leaf powder to improve the performance of water-blown rigid polyurethane foam composites
Nowadays, polyurethane (PU) foams were preferred in a broad extent of applications particularly due to their lowest thermal conductivity values satisfying the demand for energy efficiency while their use as natural filler added foam composites can reduce the polymer content allowing a more environmentally friendly production. The purpose of this work was to research the impact of olive leaf powder of various particle sizes and weight ratios on the microstructure, thermal, and mechanical properties of rigid polyurethane foam composites. All results exhibited optimum mechanical, thermal, and microstructure properties for the finest particle sized and 3 wt% added foam composites. This foam composite demonstrated an enhancement by 54%, 41%, and 61% for the tensile strength, elongation at break, and compression strength values, respectively. The thermal degradation temperature of the foam composites was also improved in correlation with the reduction of the glass transition temperature of the soft segments while the glass transition of the hard segments increased. Concerning the thermal conductivity results, the highest reduction by 11% was observed for the finest particles filled at 5 wt%, compared to the pure rigid PU foam, in correlation with the cell size showing a maximum reduction by 18% for the same composite.
- 13 June 2025
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 34 (9) , 1469-1480
Development and characterization of polypropylene or polyamide 6 hybrid composites filled with magnetite and silicon carbide
- 13 June 2025
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 34 (9) , 1469-1480
Development and characterization of polypropylene or polyamide 6 hybrid composites filled with magnetite and silicon carbide
- 1 January 2025
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 31 (7)
Impact of Titanate Coated Magnetite Nanoparticles on the Properties of Rigid Polyurethane Foams
Pamukkale University Journal of Engineering Sciences
- 1 January 2025
- Published by Pamukkale University in Pamukkale University Journal of Engineering Sciences
- Vol. 31 (7)
Impact of Titanate Coated Magnetite Nanoparticles on the Properties of Rigid Polyurethane Foams
Pamukkale University Journal of Engineering Sciences
- 30 October 2024
- Published by Elsevier in Journal of Cleaner Production
- Vol. 480
Evaluation of the use and performance of natural filler based polypropylene/leonardite composites
- 30 October 2024
- Published by Elsevier in Journal of Cleaner Production
- Vol. 480
Evaluation of the use and performance of natural filler based polypropylene/leonardite composites