Sina Baghbanrezvan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sina Baghbanrezvan has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Charles Wang Wai Ng
Hong Kong University of Science and Technology
5 shared publications- Hamed Sadeghi
Sharif University of Technology
2 shared publications C. Zhou
Department of Civil and Environmental Engineering, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong
1 shared publicationC.F. Chiu
Key Laboratory of Ministry of Education for Geomechanics and Embankment Engineering, Hohai University, 1 Xikang Road, Nanjing 210098, China
1 shared publicationC.W.W. Ng
Department of Civil and Environmental Engineering, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong
1 shared publicationChao Zhou
Department of Civil and Environmental Engineering, Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong
1 shared publication
Latest Publications
- 1 June 2024
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 61 (6) , 1266-1274
A novel three-dimensional SCR motion simulator for modelling the catenary riser–seabed interaction in a centrifuge
Steel catenary risers (SCRs) provide a cost-effective solution for deepwater oil and gas production. However, SCRs are susceptible to potential fatigue failure due to the cyclic motions of floating platforms. Previous studies on the physical modelling of cyclic SCR–seabed interactions have primarily focused on either the continuous cyclic motion of an SCR or a single rest period between two SCR motion packets. However, our understanding of the development of seabed trenches and excess pore pressure and their effects on SCR fatigue during multiple episodes of SCR motion and soil reconsolidation remains limited. This study presents a newly developed model container capable of modelling three-dimensional SCR motions including heave, surge, sway, and vortex-induced vibration in a geotechnical centrifuge. A centrifuge test is conducted to investigate the vertical cyclic SCR–seabed interaction, considering five vertical cyclic motion packets with intervening periods of reconsolidation. The results indicate that ignoring the effects of reconsolidation leads to an overestimation of the fatigue life of an SCR. In this test, the SCR fatigue life is reduced by 18%–23% after five episodic SCR motion packets and intervening reconsolidation.
- 1 June 2024
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 61 (6) , 1266-1274
A novel three-dimensional SCR motion simulator for modelling the catenary riser–seabed interaction in a centrifuge
Steel catenary risers (SCRs) provide a cost-effective solution for deepwater oil and gas production. However, SCRs are susceptible to potential fatigue failure due to the cyclic motions of floating platforms. Previous studies on the physical modelling of cyclic SCR–seabed interactions have primarily focused on either the continuous cyclic motion of an SCR or a single rest period between two SCR motion packets. However, our understanding of the development of seabed trenches and excess pore pressure and their effects on SCR fatigue during multiple episodes of SCR motion and soil reconsolidation remains limited. This study presents a newly developed model container capable of modelling three-dimensional SCR motions including heave, surge, sway, and vortex-induced vibration in a geotechnical centrifuge. A centrifuge test is conducted to investigate the vertical cyclic SCR–seabed interaction, considering five vertical cyclic motion packets with intervening periods of reconsolidation. The results indicate that ignoring the effects of reconsolidation leads to an overestimation of the fatigue life of an SCR. In this test, the SCR fatigue life is reduced by 18%–23% after five episodic SCR motion packets and intervening reconsolidation.
- Open Access
- 24 April 2023
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 382, 18001
Gas production behaviour of gas hydrate–bearing clayey-sand during depressurization: novel in-flight centrifuge modelling
Gas hydrate-bearing sediments (GHBS) are vastly distributed around the globe. While gas production attempts are made through GHBS, long-term production remains a challenge due to complex inter-related mechanisms involved. Better understating of long-term responses requires sound physical modelling conducted under controlled conditions. A novel centrifuge energy harvesting chamber (CEHC) at the HKUST centrifuge facility is used in this study. This is the first chamber that can operate at elevated gravities with the capability of sustaining the thermodynamically favourable conditions for gas hydrate formation, sustaining a continuous inflow of high-pressure water at the boundaries during dissociation, and an in-flight control of wellbore pressure and surcharge loading. Centrifuge modelling can recreate the insitu stress gradient in a relatively small model and expedite conduction and convection processes involved during dissociation. Consequently, long-term in-situ mechanisms can be evaluated with a small model and short time. A test was conducted at 40g to evaluate the temperature-pressure response as well as gas production behaviour of hydrate-bearing clayey-sand during depressurization. The results suggests that the gas flow rate is governed by the initial available latent heat as well as the conduction and convection heat through the surrounding sediments. However, as the depressurization progresses, the gas production rate is governed by the competing effects of hydrate dissociation and re-formation which both evolves the permeability of the sediment. Details of the experiment and test results are reported in this paper.
- 24 April 2023
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 382, 18001
Open AccessGas production behaviour of gas hydrate–bearing clayey-sand during depressurization: novel in-flight centrifuge modelling
Gas hydrate-bearing sediments (GHBS) are vastly distributed around the globe. While gas production attempts are made through GHBS, long-term production remains a challenge due to complex inter-related mechanisms involved. Better understating of long-term responses requires sound physical modelling conducted under controlled conditions. A novel centrifuge energy harvesting chamber (CEHC) at the HKUST centrifuge facility is used in this study. This is the first chamber that can operate at elevated gravities with the capability of sustaining the thermodynamically favourable conditions for gas hydrate formation, sustaining a continuous inflow of high-pressure water at the boundaries during dissociation, and an in-flight control of wellbore pressure and surcharge loading. Centrifuge modelling can recreate the insitu stress gradient in a relatively small model and expedite conduction and convection processes involved during dissociation. Consequently, long-term in-situ mechanisms can be evaluated with a small model and short time. A test was conducted at 40g to evaluate the temperature-pressure response as well as gas production behaviour of hydrate-bearing clayey-sand during depressurization. The results suggests that the gas flow rate is governed by the initial available latent heat as well as the conduction and convection heat through the surrounding sediments. However, as the depressurization progresses, the gas production rate is governed by the competing effects of hydrate dissociation and re-formation which both evolves the permeability of the sediment. Details of the experiment and test results are reported in this paper.
- 1 March 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (3) , 04021199
Effects of Hydrate Dissociation on Vertical Casing–Sediment Interaction in Carbon Dioxide Hydrate–Bearing Sand: Novel In-Flight Centrifuge Modeling
Gas hydrate-bearing sediments (GHBS) are vastly distributed worldwide. Although dissociation of GHBS by depressurization is considered a viable method to produce gas to meet increasing energy demand, it can alter the hydromechanical properties of GHBS by imposing additional stresses on it, which can induce instabilities in the wellbore casing. Despite many short-term gas production trials, the long-term stability and mechanisms of casing–sediment interaction remain unclear. This paper presents a novel centrifuge test using the newly developed energy harvesting chamber to investigate the effects of dissociation on vertical casing–sediment interaction and GHBS response in-flight. Test results reveal that temperature–pressure profiles evolve continuously as hydrate is dissociated, causing extension of dissociation front and inducing changes in effective stress. Dissociation within a perforated interval leads to stress transfer within the formation, resulting in vertical arching. As hydrate dissociation continues, downward movements of soil mobilize negative skin friction. The progressive hydrate dissociation could induce large axial compressive and tensile loads within and above the perforated interval, respectively. The induced axial loads evolve, and the location of neutral planes changes with the progression of hydrate dissociation. During depressurization, the compressive load in the casing exceeds the yield strength of the modeled prototype casing. Although the induced tensile loads are smaller than the yielding strength of the casing, the cement above the perforated interval might crack in tension and jeopardize the well’s integrity. Hence, both induced compressive and tensile axial loads during long-term hydrate dissociation should be carefully considered for safe gas production in GHBS.
- 1 March 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (3) , 04021199
Effects of Hydrate Dissociation on Vertical Casing–Sediment Interaction in Carbon Dioxide Hydrate–Bearing Sand: Novel In-Flight Centrifuge Modeling
Gas hydrate-bearing sediments (GHBS) are vastly distributed worldwide. Although dissociation of GHBS by depressurization is considered a viable method to produce gas to meet increasing energy demand, it can alter the hydromechanical properties of GHBS by imposing additional stresses on it, which can induce instabilities in the wellbore casing. Despite many short-term gas production trials, the long-term stability and mechanisms of casing–sediment interaction remain unclear. This paper presents a novel centrifuge test using the newly developed energy harvesting chamber to investigate the effects of dissociation on vertical casing–sediment interaction and GHBS response in-flight. Test results reveal that temperature–pressure profiles evolve continuously as hydrate is dissociated, causing extension of dissociation front and inducing changes in effective stress. Dissociation within a perforated interval leads to stress transfer within the formation, resulting in vertical arching. As hydrate dissociation continues, downward movements of soil mobilize negative skin friction. The progressive hydrate dissociation could induce large axial compressive and tensile loads within and above the perforated interval, respectively. The induced axial loads evolve, and the location of neutral planes changes with the progression of hydrate dissociation. During depressurization, the compressive load in the casing exceeds the yield strength of the modeled prototype casing. Although the induced tensile loads are smaller than the yielding strength of the casing, the cement above the perforated interval might crack in tension and jeopardize the well’s integrity. Hence, both induced compressive and tensile axial loads during long-term hydrate dissociation should be carefully considered for safe gas production in GHBS.
- 1 December 2020
- Published by Emerald Publishing in Géotechnique
- Vol. 70 (12) , 1094-1108
A state-dependent constitutive model for methane hydrate-bearing sediments inside the stability region
The presence of methane hydrate in soil pores alters the stress–strain and volumetric behaviour of soil. The extent of this alteration is affected by initial temperature and pore pressure when hydrate is formed inside the thermodynamically stable region. In this paper, a state-dependent critical state model is developed for methane hydrate-bearing sediments (MHBS) within the theoretical framework of bounding surface plasticity. A phase parameter is newly introduced into the constitutive model to account for the coupled effects of temperature and pore pressure on the mechanical behaviour of MHBS. This unique feature of the proposed model enables it to capture the behaviour of MHBS inside the methane hydrate stability region. A non-associated flow rule is adopted and a modified dilatancy expression is proposed considering the degree of hydrate saturation, phase parameter and stress state of MHBS. To verify the new model, computed results are compared to measured results of drained triaxial tests on MHBS with different morphologies and at different effective confining stresses, degrees of hydrate saturation and phase states inside the stability region. The comparison reveals that the model is capable of capturing the key features such as the evident strain-softening behaviour due to hydrate degradation and the change in stress–strain and volumetric behaviour of MHBS at different initial conditions inside the stability region.
- 1 December 2020
- Published by Emerald Publishing in Géotechnique
- Vol. 70 (12) , 1094-1108
A state-dependent constitutive model for methane hydrate-bearing sediments inside the stability region
The presence of methane hydrate in soil pores alters the stress–strain and volumetric behaviour of soil. The extent of this alteration is affected by initial temperature and pore pressure when hydrate is formed inside the thermodynamically stable region. In this paper, a state-dependent critical state model is developed for methane hydrate-bearing sediments (MHBS) within the theoretical framework of bounding surface plasticity. A phase parameter is newly introduced into the constitutive model to account for the coupled effects of temperature and pore pressure on the mechanical behaviour of MHBS. This unique feature of the proposed model enables it to capture the behaviour of MHBS inside the methane hydrate stability region. A non-associated flow rule is adopted and a modified dilatancy expression is proposed considering the degree of hydrate saturation, phase parameter and stress state of MHBS. To verify the new model, computed results are compared to measured results of drained triaxial tests on MHBS with different morphologies and at different effective confining stresses, degrees of hydrate saturation and phase states inside the stability region. The comparison reveals that the model is capable of capturing the key features such as the evident strain-softening behaviour due to hydrate degradation and the change in stress–strain and volumetric behaviour of MHBS at different initial conditions inside the stability region.
- 1 September 2017
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 54 (9) , 1310-1319
Effect of specimen preparation techniques on dynamic properties of unsaturated fine-grained soil at high suctions
The seismic response of soil depends on proper evaluation and use of soil dynamic properties, including shear modulus and damping ratio at various strain levels. Despite extensive studies on the shear modulus and damping ratio of saturated soils, research on the dynamic properties of unsaturated fine-grained soils — especially at high suction — is limited. This study aims to investigate the dynamic properties of loess at a variety of initial states resulting from different specimen preparation techniques (reconstituted, recompacted, and intact) and their evolutions due to suction-induced desiccation. Results of resonant column tests show that at initial states, the specimen preparation technique has a negligible effect on the normalized modulus (G/Gmax) and damping degradation pattern, while the influence becomes significant at a high suction (40 MPa). This is attributed to the microstructural evolution of specimens with different initial states that were subjected to suction-induced desiccation. More specifically, the elastic shear strain threshold decreases (reduction of elastic range) while shear modulus increases as suction reaches 40 MPa. Furthermore, the rate of increase in the damping ratio as well as degradation of the shear modulus for specimens at high suction is faster than their initial states. Based on the scanning electron microscopy observations, these findings may be attributed to the aggregation of larger silt–clay assemblies induced by suction increase. Consequently, soil with larger aggregates behaves more like granular sandy soil than saturated silt or clay.
- 1 September 2017
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 54 (9) , 1310-1319
Effect of specimen preparation techniques on dynamic properties of unsaturated fine-grained soil at high suctions
The seismic response of soil depends on proper evaluation and use of soil dynamic properties, including shear modulus and damping ratio at various strain levels. Despite extensive studies on the shear modulus and damping ratio of saturated soils, research on the dynamic properties of unsaturated fine-grained soils — especially at high suction — is limited. This study aims to investigate the dynamic properties of loess at a variety of initial states resulting from different specimen preparation techniques (reconstituted, recompacted, and intact) and their evolutions due to suction-induced desiccation. Results of resonant column tests show that at initial states, the specimen preparation technique has a negligible effect on the normalized modulus (G/Gmax) and damping degradation pattern, while the influence becomes significant at a high suction (40 MPa). This is attributed to the microstructural evolution of specimens with different initial states that were subjected to suction-induced desiccation. More specifically, the elastic shear strain threshold decreases (reduction of elastic range) while shear modulus increases as suction reaches 40 MPa. Furthermore, the rate of increase in the damping ratio as well as degradation of the shear modulus for specimens at high suction is faster than their initial states. Based on the scanning electron microscopy observations, these findings may be attributed to the aggregation of larger silt–clay assemblies induced by suction increase. Consequently, soil with larger aggregates behaves more like granular sandy soil than saturated silt or clay.
- Top Cited Papers
- 1 August 2016
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 53 (8) , 1258-1269
Water retention and volumetric characteristics of intact and re-compacted loess
A laboratory testing program was conducted to investigate the effects of microstructure on the water retention curve (WRC) and wetting–drying induced volume change in loess. The axis translation and vapor equilibrium techniques were adopted to control suction in the range of 0–400 kPa and 4–140 MPa, respectively. Hysteresis in the WRC of loess was observed for the entire range of suction studied. Compared to re-compacted loess, intact loess exhibits a more pronounced hysteresis in the suction range below 20 kPa, which can be explained by the ink-bottle pore neck effect or constricted pores. The hypothesis is supported by microstructural evidence of mercury intrusion porosimetry and scanning electron microscopy tests. However, re-compacted loess exhibits larger hysteresis than intact loess for suctions above 30 kPa. A conceptual model was introduced, which links WRC to the corresponding pore-size density (PSD) function. Regarding volume change, more noticeable drying-induced shrinkage, but yielding at a lower suction, was observed for re-compacted loess. This is consistent with the compression test results. Stress has a significant effect on change of PSD and constricted macropores leading to a shift in the main wetting curve and a less pronounced hysteresis. Intact loess exhibits a stress-dependent wetting-induced collapse and drying-induced shrinkage.
- 1 August 2016
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 53 (8) , 1258-1269
Top Cited PapersWater retention and volumetric characteristics of intact and re-compacted loess
A laboratory testing program was conducted to investigate the effects of microstructure on the water retention curve (WRC) and wetting–drying induced volume change in loess. The axis translation and vapor equilibrium techniques were adopted to control suction in the range of 0–400 kPa and 4–140 MPa, respectively. Hysteresis in the WRC of loess was observed for the entire range of suction studied. Compared to re-compacted loess, intact loess exhibits a more pronounced hysteresis in the suction range below 20 kPa, which can be explained by the ink-bottle pore neck effect or constricted pores. The hypothesis is supported by microstructural evidence of mercury intrusion porosimetry and scanning electron microscopy tests. However, re-compacted loess exhibits larger hysteresis than intact loess for suctions above 30 kPa. A conceptual model was introduced, which links WRC to the corresponding pore-size density (PSD) function. Regarding volume change, more noticeable drying-induced shrinkage, but yielding at a lower suction, was observed for re-compacted loess. This is consistent with the compression test results. Stress has a significant effect on change of PSD and constricted macropores leading to a shift in the main wetting curve and a less pronounced hysteresis. Intact loess exhibits a stress-dependent wetting-induced collapse and drying-induced shrinkage.