Edward Della Torre
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Edward Della Torre has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Lawrence H. Bennett
Institute for Magnetics Research, The George Washington University, Ashburn, Virginia 20147
8 shared publications - Mohammadreza Ghahremani
Department of Computer Science, Mathematics and Engineering, Shepherd University, Shepherdstown, WV 25443, USA
8 shared publications - Hatem ElBidweihy
U.S. Naval Academy (United States)
7 shared publications Lawrence H. Bennett
Department of Electrical and Computer Engineering, The George Washington University, Washington, DC 20052, USA
5 shared publications- Amir Aslani
Department of Electrical and Computer Engineering, George Washington University, Washington DC 20052, USA
4 shared publications - LawrenceH. Bennett
Department of Electrical and Computer Engineering, George Washington University 2 , Washington DC 20052, USA
4 shared publications
Latest Publications
- Open Access
- 4 January 2018
- Published by AIP Publishing in AIP Advances
- Vol. 8 (5)
Direct and indirect measurement of the magnetocaloric effect in bulk and nanostructured Ni-Mn-In Heusler alloy
A systematic study of the magnetocaloric effect of a Ni51Mn33.4In15.6 Heusler alloy converted to nanoparticles via high energy ball-milling technique in the temperature range of 270 to 310 K has been performed. The properties of the particles were characterized by x-ray diffraction, electron microscopy, and magnetometer techniques. Isothermal magnetic field variation of magnetization exhibits field hysteresis in bulk Ni51Mn33.4In15.6 alloy across the martensitic transition which significantly lessened in the nanoparticles. The magnetocaloric effects of the bulk and nanoparticle samples were measured both with direct method, through our state of the art direct test bed apparatus with controllability over the applied fields and temperatures, as well as an indirect method through Maxwell and thermodynamic equations. In direct measurements, nanoparticle sample’s critical temperature decreased by 6 K, but its magnetocaloric effect enhanced by 17% over the bulk counterpart. Additionally, when comparing the direct and indirect magnetocaloric curves, the direct method showed 14% less adiabatic temperature change in the bulk and 5% less adiabatic temperature change in the nanostructured sample.
- 4 January 2018
- Published by AIP Publishing in AIP Advances
- Vol. 8 (5)
Open AccessDirect and indirect measurement of the magnetocaloric effect in bulk and nanostructured Ni-Mn-In Heusler alloy
A systematic study of the magnetocaloric effect of a Ni51Mn33.4In15.6 Heusler alloy converted to nanoparticles via high energy ball-milling technique in the temperature range of 270 to 310 K has been performed. The properties of the particles were characterized by x-ray diffraction, electron microscopy, and magnetometer techniques. Isothermal magnetic field variation of magnetization exhibits field hysteresis in bulk Ni51Mn33.4In15.6 alloy across the martensitic transition which significantly lessened in the nanoparticles. The magnetocaloric effects of the bulk and nanoparticle samples were measured both with direct method, through our state of the art direct test bed apparatus with controllability over the applied fields and temperatures, as well as an indirect method through Maxwell and thermodynamic equations. In direct measurements, nanoparticle sample’s critical temperature decreased by 6 K, but its magnetocaloric effect enhanced by 17% over the bulk counterpart. Additionally, when comparing the direct and indirect magnetocaloric curves, the direct method showed 14% less adiabatic temperature change in the bulk and 5% less adiabatic temperature change in the nanostructured sample.
- Open Access
- 3 February 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (5)
Enhanced magnetic properties of yttrium-iron nanoparticles
A systematic study of the size effect on the magnetic and structural properties of Y2Fe17 nanoparticles has been performed. We present new data to explain the enhanced magnetic properties of nanostructured yttrium-iron alloy synthesized through alkalide reduction chemical synthesis. The properties of the particles were characterized by x-ray diffraction, electron microscopy, and magnetometer techniques. As the size of the nanoparticles is reduced, there is an increase in magnetization per unit of applied magnetic field, a decrease in the coercivity and a substantial reduction in hysteresis.
- 3 February 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (5)
Open AccessEnhanced magnetic properties of yttrium-iron nanoparticles
A systematic study of the size effect on the magnetic and structural properties of Y2Fe17 nanoparticles has been performed. We present new data to explain the enhanced magnetic properties of nanostructured yttrium-iron alloy synthesized through alkalide reduction chemical synthesis. The properties of the particles were characterized by x-ray diffraction, electron microscopy, and magnetometer techniques. As the size of the nanoparticles is reduced, there is an increase in magnetization per unit of applied magnetic field, a decrease in the coercivity and a substantial reduction in hysteresis.
- Open Access
- 23 January 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (5) , 056010
Vector magnetization of a distribution of cubic particles
A model for the vector magnetization of a distribution of particles with cubic anisotropy is presented. Recent work by the authors modeled the vector magnetization of a distribution of uniaxial particles by decomposing the total magnetization into reversible and irreversible components. In this paper, using an energy approach applicable to a generic plane, the model is extended to include cubic anisotropy projected to the (100) plane. The magnitude of the irreversible component is modeled using a Preisach differential-equation approach; however, other valid models can be used. The direction of the reversible component is modeled using the minimum energy approach of the classical Stoner–Wohlfarth model and taking into account the anisotropy field. The formulation of the generalized model is derived and its results are discussed considering (i) oscillation and rotational modes, (ii) lag angle, and (iii) magnetization trajectories.
- 23 January 2017
- Published by AIP Publishing in AIP Advances
- Vol. 7 (5) , 056010
Open AccessVector magnetization of a distribution of cubic particles
A model for the vector magnetization of a distribution of particles with cubic anisotropy is presented. Recent work by the authors modeled the vector magnetization of a distribution of uniaxial particles by decomposing the total magnetization into reversible and irreversible components. In this paper, using an energy approach applicable to a generic plane, the model is extended to include cubic anisotropy projected to the (100) plane. The magnitude of the irreversible component is modeled using a Preisach differential-equation approach; however, other valid models can be used. The direction of the reversible component is modeled using the minimum energy approach of the classical Stoner–Wohlfarth model and taking into account the anisotropy field. The formulation of the generalized model is derived and its results are discussed considering (i) oscillation and rotational modes, (ii) lag angle, and (iii) magnetization trajectories.
- Open Access
- 1 July 2016
- Published by AIP Publishing in AIP Advances
- Vol. 6 (7) , 075221
Tuning the heat transfer medium and operating conditions in magnetic refrigeration
A new experimental test bed has been designed, built, and tested to evaluate the effect of the system’s parameters on a reciprocating Active Magnetic Regenerator (AMR) near room temperature. Bulk gadolinium was used as the refrigerant, silicon oil as the heat transfer medium, and a magnetic field of 1.3 T was cycled. This study focuses on the methodology of single stage AMR operation conditions to get a high temperature span near room temperature. Herein, the main objective is not to report the absolute maximum attainable temperature span seen in an AMR system, but rather to find the system’s optimal operating conditions to reach that maximum span. The results of this research show that there is a optimal operating frequency, heat transfer fluid flow rate, flow duration, and displaced volume ratio in any AMR system. By optimizing these parameters in our AMR apparatus the temperature span between the hot and cold ends increased by 24%. The optimized values are system dependent and need to be determined and measured for any AMR system by following the procedures that are introduced in this research. It is expected that such optimization will permit the design of a more efficient magnetic refrigeration system.
- 1 July 2016
- Published by AIP Publishing in AIP Advances
- Vol. 6 (7) , 075221
Open AccessTuning the heat transfer medium and operating conditions in magnetic refrigeration
A new experimental test bed has been designed, built, and tested to evaluate the effect of the system’s parameters on a reciprocating Active Magnetic Regenerator (AMR) near room temperature. Bulk gadolinium was used as the refrigerant, silicon oil as the heat transfer medium, and a magnetic field of 1.3 T was cycled. This study focuses on the methodology of single stage AMR operation conditions to get a high temperature span near room temperature. Herein, the main objective is not to report the absolute maximum attainable temperature span seen in an AMR system, but rather to find the system’s optimal operating conditions to reach that maximum span. The results of this research show that there is a optimal operating frequency, heat transfer fluid flow rate, flow duration, and displaced volume ratio in any AMR system. By optimizing these parameters in our AMR apparatus the temperature span between the hot and cold ends increased by 24%. The optimized values are system dependent and need to be determined and measured for any AMR system by following the procedures that are introduced in this research. It is expected that such optimization will permit the design of a more efficient magnetic refrigeration system.
- Open Access
- 5 November 2015
- Published by Taylor & Francis in Cogent Physics
- Vol. 2 (1) , 1109019
Magnetic states stabilization in Ni51Mn33.4In15.6 Heusler alloy
The rate-independent stabilization of magnetic states with iterations in a Heusler alloy has been studied. The direct measurement of the adiabatic temperature change, ΔTad, of a Ni51Mn33.4In15.6 alloy near the magnetostructural phase transition is presented. The adiabatic temperature change at a given temperature within the temperature range of the magnetostructural transition is history dependent and varies considerably with the iteration count of the field cycle. The data show the transition from the low magnetization state to the high magnetization state during low to high (L–H) temperature change direction and from high magnetization to low magnetization state during high to low (H–L) temperature change direction require several field cycles to stabilize the ΔTad measurement, similar to the accommodation phenomenon in hysteretic materials. In the mixed magnetic state inside the first-order transition, both low and high magnetization portions of the alloy exist and it varies considerably with the induced fields. This original observation emphasizes that it is incorrect to assess the performance of a magnetic refrigeration system through a single measurement, and that achieving a stable, utilizable, adiabatic temperature change requires several field-induced transitions.
- 5 November 2015
- Published by Taylor & Francis in Cogent Physics
- Vol. 2 (1) , 1109019
Open AccessMagnetic states stabilization in Ni51Mn33.4In15.6 Heusler alloy
The rate-independent stabilization of magnetic states with iterations in a Heusler alloy has been studied. The direct measurement of the adiabatic temperature change, ΔTad, of a Ni51Mn33.4In15.6 alloy near the magnetostructural phase transition is presented. The adiabatic temperature change at a given temperature within the temperature range of the magnetostructural transition is history dependent and varies considerably with the iteration count of the field cycle. The data show the transition from the low magnetization state to the high magnetization state during low to high (L–H) temperature change direction and from high magnetization to low magnetization state during high to low (H–L) temperature change direction require several field cycles to stabilize the ΔTad measurement, similar to the accommodation phenomenon in hysteretic materials. In the mixed magnetic state inside the first-order transition, both low and high magnetization portions of the alloy exist and it varies considerably with the induced fields. This original observation emphasizes that it is incorrect to assess the performance of a magnetic refrigeration system through a single measurement, and that achieving a stable, utilizable, adiabatic temperature change requires several field-induced transitions.
- 14 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17D141
Vector properties of magnetostriction
The vector properties of a newly developed Preisach-type magnetostriction model are discussed. The model uses a modified version of the Della Torre-Pinzaglia-Cardelli model to compute the irreversible and the reversible components of the magnetization. The magnetostriction can then be simulated by assuming that its magnitude is proportional to the magnetization and its direction is dependent on the magnetization history. The modeling approach is outlined for two types of isotropic media: native and polycrystalline. The preliminary results show excellent agreement with the rotational magnetization measurements for a sample of high-strength steel.
- 14 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17D141
Vector properties of magnetostriction
The vector properties of a newly developed Preisach-type magnetostriction model are discussed. The model uses a modified version of the Della Torre-Pinzaglia-Cardelli model to compute the irreversible and the reversible components of the magnetization. The magnetostriction can then be simulated by assuming that its magnitude is proportional to the magnetization and its direction is dependent on the magnetization history. The modeling approach is outlined for two types of isotropic media: native and polycrystalline. The preliminary results show excellent agreement with the rotational magnetization measurements for a sample of high-strength steel.
- 30 January 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17D107
Magnetocaloric effect in NiMnInSi Heusler alloys
The NiMnInSi Heusler alloy family is analyzed, and a self-similarity based method is used to analyze the first-order transition of Ni-Mn Heusler alloys. This method is appropriate to determine magnetic characteristics of the Magnetocaloric Effect providing that there is sufficient separation in their phase transition temperatures. A temperature scaling methodology is used to model the cluster compositions in the mixed-state regions where two stable magnetic states co-exist. The various descriptions and classifications of these transitions, however, are not critical to this analysis.
- 30 January 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 17D107
Magnetocaloric effect in NiMnInSi Heusler alloys
The NiMnInSi Heusler alloy family is analyzed, and a self-similarity based method is used to analyze the first-order transition of Ni-Mn Heusler alloys. This method is appropriate to determine magnetic characteristics of the Magnetocaloric Effect providing that there is sufficient separation in their phase transition temperatures. A temperature scaling methodology is used to model the cluster compositions in the mixed-state regions where two stable magnetic states co-exist. The various descriptions and classifications of these transitions, however, are not critical to this analysis.
- Open Access
- 24 November 2014
- Published by Taylor & Francis in Cogent Physics
- Vol. 1 (1)
Cooling factor for magnetic refrigeration systems
The adiabatic temperature change (ΔTad) during the magnetization process of polycrystalline gadolinium and Ni51Mn33.4In15.6 Heusler alloy is directly measured near the Curie temperature. The cooling factor (CF) is introduced as the area under the curve of adiabatic temperature change versus ambient temperature. The CF provides more representative measure of cooling performance in the operational temperature range. Selecting different temperature abscissas qualitatively changes the interpretation of the cooling performance of a magnetocaloric material. In particular, plotting ΔTad versus initial temperature gives a measurably different CF compared to that given by plotting ΔTad versus average temperature
- 24 November 2014
- Published by Taylor & Francis in Cogent Physics
- Vol. 1 (1)
Open AccessCooling factor for magnetic refrigeration systems
The adiabatic temperature change (ΔTad) during the magnetization process of polycrystalline gadolinium and Ni51Mn33.4In15.6 Heusler alloy is directly measured near the Curie temperature. The cooling factor (CF) is introduced as the area under the curve of adiabatic temperature change versus ambient temperature. The CF provides more representative measure of cooling performance in the operational temperature range. Selecting different temperature abscissas qualitatively changes the interpretation of the cooling performance of a magnetocaloric material. In particular, plotting ΔTad versus initial temperature gives a measurably different CF compared to that given by plotting ΔTad versus average temperature
- 26 February 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 50 (2) , 329-332
Numerical Modeling of Hysteresis in Si-Fe Steels
In this paper, we discuss the numerical modeling of hysteresis in magnetic steels with oriented and nonoriented grain. The modeling is fully 3-D, but it is applied here to typical 2-D magnetic problems. Starting from a vector generalization of the Preisach model, we introduce here the concept of an operative magnetic field, function of the state of magnetization of the material. This operative field is introduced to reproduce with more accuracy the peculiar behavior of Si-Fe steels approaching the saturation state. The properties of the model are discussed and some examples are reported.
- 26 February 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 50 (2) , 329-332
Numerical Modeling of Hysteresis in Si-Fe Steels
In this paper, we discuss the numerical modeling of hysteresis in magnetic steels with oriented and nonoriented grain. The modeling is fully 3-D, but it is applied here to typical 2-D magnetic problems. Starting from a vector generalization of the Preisach model, we introduce here the concept of an operative magnetic field, function of the state of magnetization of the material. This operative field is introduced to reproduce with more accuracy the peculiar behavior of Si-Fe steels approaching the saturation state. The properties of the model are discussed and some examples are reported.
- 1 February 2014
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 435, 138-143
Hysteresis of magnetostructural transitions: Repeatable and non-repeatable processes
- 1 February 2014
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 435, 138-143
Hysteresis of magnetostructural transitions: Repeatable and non-repeatable processes