Erik Fischer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Erik Fischer has a total of 271 co-authors. Here are the top co-authors by number of shared publications:
- German Martinez
Centro de Astrobiología (CSIC‐INTA) Madrid Spain
10 shared publications - Mark T. Lemmon
Space Science Institute Boulder CO USA
8 shared publications - Ricardo Hueso
Bilbao School of Engineering, Universidad del País Vasco UPV/EHU, Bilbao, Spain
8 shared publications - Asier Munguira
Física Aplicada Escuela de Ingeniería de Bilbao Universidad del País Vasco UPV/EHU Bilbao Spain
7 shared publications - Claire Newman
Aeolis Research Chandler AZ USA
7 shared publications - Ignacio Arruego
Instituto Nacional de Técnica Aeroespacial (INTA) Madrid Spain
7 shared publications
Latest Publications
- Open Access
- 3 July 2024
- Published by Copernicus GmbH
Updated calibration and results of the REMS-H humidity sensor of the MSL Curiosity
The Curiosity rover, part of the Mars Science Laboratory (MSL), landed in Gale crater in 2012 with the Rover Environmental Monitoring Station (REMS)[1] onboard. REMS includes an atmospheric relative humidity sensor, REMS-H, provided by the Finnish Meteorological Institute (FMI)[2]. REMS-H has continuously recorded hourly near-surface humidity conditions on Mars since landing, resulting in a rich dataset. As of May 2024, REMS-H has been operational for a little over 4100 sols; more than 11 Earth years, providing the longest relative humidity record from the surface of Mars.Figure 1: REMS-H is located in the boom of Curiosity’s mast. Credit: NASA/JPL-Caltech/MSSSThe current calibration of REMS-H has been evaluated using new calibration measurements performed under a Martian analogue environment at DLR PASLAB (Planetary Analog Simulation Laboratory) at the German Aerospace Center (DLR)[3]. The capacitive sensor type, that has been used in all in situ measurements so far, can be sensitive not only to relative humidity but also other variables like temperature, pressure and carbon dioxide (CO2)[4].Based on the findings a revised calibration has been developed for REMS-H. This presentation outlines both the revised calibration and the corresponding updated results. Particularly two aspects of the calibration can now be corrected using real measurement data: the RH response function between 0% and 100% rh, and the dynamic range of the sensor in CO2. Furthermore, a two-part calibration correction based on flight data analysis is described.The revisited results section presents the revised interannual, seasonal, and diurnal variations in relative humidity, temperature, and derived water vapor mixing ratio (VMR). Comparisons with previous calibration results are also discussed. In general, the new calibration resulted in somewhat lower relative humidity values, although the difference varies. On average the difference is about 10% rh. In VMR, the difference is more prominent and temperature dependent. A couple of example sols with current and revised calibration are shown in Figure 2. The full dataset will be available in a subsequent manuscript that is currently under preparation [5].The resulting new dataset is well aligned with orbital observations and M2020 MEDA HS observations from the same time period. Also the UH/FMI single-column model (SCM)[e.g. 6] has been used to evaluate the revised results with good agreement.In conclusion, the recalibration effort has improved the accuracy and reliability of REMS-H data, aligning the results with orbital observations and simulation runs. While we believe that the new measurements provide a more accurate representation of humidity values on Mars, it's important to consider the relatively large uncertainty, particularly when RH levels are low, when using the data.Figure 2: Example comparisons of old (red) and revised (blue) relative humidity measurements from sols 2530 (Ls=81.6°) and 3211 (Ls=87.2°) during southern winter. Sensor temperature is plotted in orange. In most sols the revised RH is lower than previously, but that is not always the case as can be seen in sol 3211 night time observations.References:[1] J. Gomez-Elvira et al.: REMS: The Environmental Sensor Suite for the Mars Science Laboratory Rover. Space Science Reviews 170, 583–640, 2012.[2] Harri, A.-M. et al.: Mars Science Laboratory relative humidity observations: Initial results. Journal of Geophysical Research: Planets, 119, 2132–2147, 2014.[3] Hieta et al.: Improving relative humidity measurements on Mars: New laboratory calibration measurements. Geoscientific Instrumentation, Methods and Data Systems, in review[4] Lorek, A. and Majewski, J.: Humidity Measurement in Carbon Dioxide with Capacitive Humidity Sensors at Low Temperature and Pressure. Sensors, 18, 2615, 2018.[5] Hieta et al.: REMS-H Revisited: Updated calibration and results of the humidity sensor of the MSL Curiosity. Space Science Reviews, In preparation[6] Savijärvi, H. I., Harri, A.-M., & Kemppinen, O.: The diurnal water cycle at Curiosity: Role of exchange with the regolith. Icarus, 265, 63–69, 2016.
- 3 July 2024
- Published by Copernicus GmbH
Open AccessUpdated calibration and results of the REMS-H humidity sensor of the MSL Curiosity
The Curiosity rover, part of the Mars Science Laboratory (MSL), landed in Gale crater in 2012 with the Rover Environmental Monitoring Station (REMS)[1] onboard. REMS includes an atmospheric relative humidity sensor, REMS-H, provided by the Finnish Meteorological Institute (FMI)[2]. REMS-H has continuously recorded hourly near-surface humidity conditions on Mars since landing, resulting in a rich dataset. As of May 2024, REMS-H has been operational for a little over 4100 sols; more than 11 Earth years, providing the longest relative humidity record from the surface of Mars.Figure 1: REMS-H is located in the boom of Curiosity’s mast. Credit: NASA/JPL-Caltech/MSSSThe current calibration of REMS-H has been evaluated using new calibration measurements performed under a Martian analogue environment at DLR PASLAB (Planetary Analog Simulation Laboratory) at the German Aerospace Center (DLR)[3]. The capacitive sensor type, that has been used in all in situ measurements so far, can be sensitive not only to relative humidity but also other variables like temperature, pressure and carbon dioxide (CO2)[4].Based on the findings a revised calibration has been developed for REMS-H. This presentation outlines both the revised calibration and the corresponding updated results. Particularly two aspects of the calibration can now be corrected using real measurement data: the RH response function between 0% and 100% rh, and the dynamic range of the sensor in CO2. Furthermore, a two-part calibration correction based on flight data analysis is described.The revisited results section presents the revised interannual, seasonal, and diurnal variations in relative humidity, temperature, and derived water vapor mixing ratio (VMR). Comparisons with previous calibration results are also discussed. In general, the new calibration resulted in somewhat lower relative humidity values, although the difference varies. On average the difference is about 10% rh. In VMR, the difference is more prominent and temperature dependent. A couple of example sols with current and revised calibration are shown in Figure 2. The full dataset will be available in a subsequent manuscript that is currently under preparation [5].The resulting new dataset is well aligned with orbital observations and M2020 MEDA HS observations from the same time period. Also the UH/FMI single-column model (SCM)[e.g. 6] has been used to evaluate the revised results with good agreement.In conclusion, the recalibration effort has improved the accuracy and reliability of REMS-H data, aligning the results with orbital observations and simulation runs. While we believe that the new measurements provide a more accurate representation of humidity values on Mars, it's important to consider the relatively large uncertainty, particularly when RH levels are low, when using the data.Figure 2: Example comparisons of old (red) and revised (blue) relative humidity measurements from sols 2530 (Ls=81.6°) and 3211 (Ls=87.2°) during southern winter. Sensor temperature is plotted in orange. In most sols the revised RH is lower than previously, but that is not always the case as can be seen in sol 3211 night time observations.References:[1] J. Gomez-Elvira et al.: REMS: The Environmental Sensor Suite for the Mars Science Laboratory Rover. Space Science Reviews 170, 583–640, 2012.[2] Harri, A.-M. et al.: Mars Science Laboratory relative humidity observations: Initial results. Journal of Geophysical Research: Planets, 119, 2132–2147, 2014.[3] Hieta et al.: Improving relative humidity measurements on Mars: New laboratory calibration measurements. Geoscientific Instrumentation, Methods and Data Systems, in review[4] Lorek, A. and Majewski, J.: Humidity Measurement in Carbon Dioxide with Capacitive Humidity Sensors at Low Temperature and Pressure. Sensors, 18, 2615, 2018.[5] Hieta et al.: REMS-H Revisited: Updated calibration and results of the humidity sensor of the MSL Curiosity. Space Science Reviews, In preparation[6] Savijärvi, H. I., Harri, A.-M., & Kemppinen, O.: The diurnal water cycle at Curiosity: Role of exchange with the regolith. Icarus, 265, 63–69, 2016.
- Open Access
- 2 May 2024
- Published by Copernicus GmbH
Looking for Non-Polar Shallow Subsurface Water Ice in Preparation for Future Human Exploration of Mars
Introduction: The Mars Odyssey (MO) mission is the longest-lasting spacecraft on Mars. Launched in 2001, the orbiter has provided an unprecedented temporal coverage ranging from Martian Year (MY) 25 (Feb 2002) to current MY 36 [1]. The Neutron Spectrometer (NS) is one of the instruments onboard MO, and it has been surveying the shallow (~first meter) subsurface of Mars for hydrogen to map its amount and global distribution [2]. MO/NS measurements have been used to locate the main reservoirs of hydrogen content on Mars (Fig. 1) [3]. The flux of neutrons leaking from Mars’ surface is inversely related to the hydrogen content of the soil. This is because hydrogen is especially effective at moderating neutrons generated through collisions between cosmic rays and atoms in the Martian soil. Based on this principle, MO/NS collects neutron fluxes in three consecutive energy bands: thermal (0-0.3 eV), epithermal (0.3 eV-700 keV) (ECR), and fast (0.7-5 MeV) neutron ranges. Among these, epithermal neutrons are more useful in interpreting hydrogen abundance, as they are less sensitive to variations in the soil’s amount of heavy elements. MO/NS measurements are sensitive to the hydrogen content of the soil, but not to the type of molecular association of such hydrogen. Potential hydrogen carriers in the Martian soil include: (1) buried water ice, (2) structural water bound in salts (chemisorbed water), and (3) water molecules adsorbed on the surface of soil grains and minerals (physisorbed water) [4]. Potential shallow subsurface water ice reservoirs far from the poles are of special interest, because they may constitute an important source for future In-Situ-Resource-Utilization (ISRU). Objective: Here, we look for shallow subsurface water ice from mid to equatorial latitudes by analyzing variations in epithermal count rates (ECRs) at seasonal and sub-seasonal timescales. The magnitude and the timescale of these variations can be helpful to identify the molecular association of the hydrogen present in the shallow subsurface. Methodology: We retrieved the MO/NS data set available in NASA's PDS and stored it in a No-SQL local database to simplify analyses. Using 5° × 5° bins, we calculated the climatological (C) averages of ECRs for the entire duration of the mission, and the sub-seasonal (Sx) averages of ECRs for different periods (x) of solar longitude (Ls). In each case, we discarded measurements affected by the presence of CO2 frost. Then, we defined the relative sub-seasonal variation in each bin as RVx = (Sx-C)/C. Finally, we calculated T-test p-values corresponding to each bin and the rest of the domain considered here (-55° and 55°). Only when the returned p-value was lower than 0.05, the variation in ECRs was considered statistically robust. Preliminary Results: Fig. 2 shows areas with significant seasonal variations in ECRs during Ls periods 0° – 90° (top) and 180° – 270° (bottom). The areas highlighted in orange are Hellas Planitia in the southern hemisphere, and Utopia Rupes in the northern hemisphere. These are the only regions in which multiple, adjacent bins undergo a significant variation throughout the year. Similar results have been obtained using different bin sizes and Ls periods for which statistically-robust analyses could be performed. The relation between the seasonal variation in ECRs and the ground temperature retrieved from TES and THEMIS at Hellas Planitia and Utopia Rupes (not shown here) indicates that the coldest ground temperatures occur at the same time as the largest increase in hydrogen content is observed (and vice versa), suggesting that water ice might form in the shallow subsurface of these regions during the cold season, and then sublimating during the warm season of each hemisphere. Using modeling and satellite observations, we plan to investigate whether the magnitude and timescale of the observed seasonal changes in ECRs are consistent with changes in water ice, chemisorbed water, or physisorbed water. Conclusions and Significance: Only Hellas Planitia and Utopia Rupes (Fig. 2) undergo a statistically-significant variation in ECRs (and therefore in the hydrogen content in the first meter of their subsurface). This variation is correlated with temperature in both regions, supporting the hypothesis that shallow subsurface water ice might form and sublimate during the cold and warm seasons of each hemisphere. These results are potentially important for future human exploration of Mars, as shallow subsurface water ice far from the poles is key for ISRU. References: [1] Mesick, K. E., et al., Icarus 335 (2020): 113397. [2] Feldman, W. C., et al., J. Geophys. Res.: Planets 109.E9 (2004). [3] Wilson, J. T., et al., Icarus 299 (2018): 148-160. [4] Jakosky, B. M., et al., Icarus 175.1 (2005): 58-67.
- 2 May 2024
- Published by Copernicus GmbH
Open AccessLooking for Non-Polar Shallow Subsurface Water Ice in Preparation for Future Human Exploration of Mars
Introduction: The Mars Odyssey (MO) mission is the longest-lasting spacecraft on Mars. Launched in 2001, the orbiter has provided an unprecedented temporal coverage ranging from Martian Year (MY) 25 (Feb 2002) to current MY 36 [1]. The Neutron Spectrometer (NS) is one of the instruments onboard MO, and it has been surveying the shallow (~first meter) subsurface of Mars for hydrogen to map its amount and global distribution [2]. MO/NS measurements have been used to locate the main reservoirs of hydrogen content on Mars (Fig. 1) [3]. The flux of neutrons leaking from Mars’ surface is inversely related to the hydrogen content of the soil. This is because hydrogen is especially effective at moderating neutrons generated through collisions between cosmic rays and atoms in the Martian soil. Based on this principle, MO/NS collects neutron fluxes in three consecutive energy bands: thermal (0-0.3 eV), epithermal (0.3 eV-700 keV) (ECR), and fast (0.7-5 MeV) neutron ranges. Among these, epithermal neutrons are more useful in interpreting hydrogen abundance, as they are less sensitive to variations in the soil’s amount of heavy elements. MO/NS measurements are sensitive to the hydrogen content of the soil, but not to the type of molecular association of such hydrogen. Potential hydrogen carriers in the Martian soil include: (1) buried water ice, (2) structural water bound in salts (chemisorbed water), and (3) water molecules adsorbed on the surface of soil grains and minerals (physisorbed water) [4]. Potential shallow subsurface water ice reservoirs far from the poles are of special interest, because they may constitute an important source for future In-Situ-Resource-Utilization (ISRU). Objective: Here, we look for shallow subsurface water ice from mid to equatorial latitudes by analyzing variations in epithermal count rates (ECRs) at seasonal and sub-seasonal timescales. The magnitude and the timescale of these variations can be helpful to identify the molecular association of the hydrogen present in the shallow subsurface. Methodology: We retrieved the MO/NS data set available in NASA's PDS and stored it in a No-SQL local database to simplify analyses. Using 5° × 5° bins, we calculated the climatological (C) averages of ECRs for the entire duration of the mission, and the sub-seasonal (Sx) averages of ECRs for different periods (x) of solar longitude (Ls). In each case, we discarded measurements affected by the presence of CO2 frost. Then, we defined the relative sub-seasonal variation in each bin as RVx = (Sx-C)/C. Finally, we calculated T-test p-values corresponding to each bin and the rest of the domain considered here (-55° and 55°). Only when the returned p-value was lower than 0.05, the variation in ECRs was considered statistically robust. Preliminary Results: Fig. 2 shows areas with significant seasonal variations in ECRs during Ls periods 0° – 90° (top) and 180° – 270° (bottom). The areas highlighted in orange are Hellas Planitia in the southern hemisphere, and Utopia Rupes in the northern hemisphere. These are the only regions in which multiple, adjacent bins undergo a significant variation throughout the year. Similar results have been obtained using different bin sizes and Ls periods for which statistically-robust analyses could be performed. The relation between the seasonal variation in ECRs and the ground temperature retrieved from TES and THEMIS at Hellas Planitia and Utopia Rupes (not shown here) indicates that the coldest ground temperatures occur at the same time as the largest increase in hydrogen content is observed (and vice versa), suggesting that water ice might form in the shallow subsurface of these regions during the cold season, and then sublimating during the warm season of each hemisphere. Using modeling and satellite observations, we plan to investigate whether the magnitude and timescale of the observed seasonal changes in ECRs are consistent with changes in water ice, chemisorbed water, or physisorbed water. Conclusions and Significance: Only Hellas Planitia and Utopia Rupes (Fig. 2) undergo a statistically-significant variation in ECRs (and therefore in the hydrogen content in the first meter of their subsurface). This variation is correlated with temperature in both regions, supporting the hypothesis that shallow subsurface water ice might form and sublimate during the cold and warm seasons of each hemisphere. These results are potentially important for future human exploration of Mars, as shallow subsurface water ice far from the poles is key for ISRU. References: [1] Mesick, K. E., et al., Icarus 335 (2020): 113397. [2] Feldman, W. C., et al., J. Geophys. Res.: Planets 109.E9 (2004). [3] Wilson, J. T., et al., Icarus 299 (2018): 148-160. [4] Jakosky, B. M., et al., Icarus 175.1 (2005): 58-67.
- Open Access
- 30 October 2023
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 128 (11)
Mineralogical Investigation of Mg‐Sulfate at the Canaima Drill Site, Gale Crater, Mars
For the first time on Mars, the crystalline magnesium‐sulfate mineral starkeyite (MgSO 4 ‧4H 2 O) was definitively identified using the CheMin X‐ray diffraction instrument at Gale crater. At the Canaima drill site, starkeyite along with amorphous MgSO 4 ‧ n H 2 O are among the “polyhydrated Mg‐sulfates” interpreted in orbital reflectance spectra. Mg‐sulfates are good climate indicators as they are very responsive to changes in temperature and relative humidity. We hypothesize that, through evaporation, Mg‐sulfates formed at the end of brine evolution when ion concentrations became saturated and precipitated on the surface or near sub‐surface as either epsomite or meridianiite. These minerals were subsequently dehydrated later to starkeyite and amorphous MgSO 4 ‧ n H 2 O in response to a drier Mars. At Canaima, starkeyite is stable and would form during the warmer Mars summers. Due to very slow kinetics at the low Mars winter temperatures, starkeyite and amorphous MgSO 4 ‧ n H 2 O would be resistant to recrystallize to more hydrous forms and thus likely persist year‐round. During the course of analyses, starkeyite transforms into amorphous MgSO 4 ‧ n H 2 O inside the rover body due to the elevated temperature and greatly reduced relative humidity compared to the martian surface at the Canaima drill site. It is possible that crystalline sulfate minerals existed in earlier samples measured by CheMin but altered inside the rover before they could be analyzed. Starkeyite is most likely prevalent in the subsurface, whereas both starkeyite and amorphous MgSO 4 ‧ n H 2 O are likely present on the surface as starkeyite could partially transform into amorphous MgSO 4 ‧ n H 2 O due to direct solar heating.
- 30 October 2023
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 128 (11)
Open AccessMineralogical Investigation of Mg‐Sulfate at the Canaima Drill Site, Gale Crater, Mars
For the first time on Mars, the crystalline magnesium‐sulfate mineral starkeyite (MgSO 4 ‧4H 2 O) was definitively identified using the CheMin X‐ray diffraction instrument at Gale crater. At the Canaima drill site, starkeyite along with amorphous MgSO 4 ‧ n H 2 O are among the “polyhydrated Mg‐sulfates” interpreted in orbital reflectance spectra. Mg‐sulfates are good climate indicators as they are very responsive to changes in temperature and relative humidity. We hypothesize that, through evaporation, Mg‐sulfates formed at the end of brine evolution when ion concentrations became saturated and precipitated on the surface or near sub‐surface as either epsomite or meridianiite. These minerals were subsequently dehydrated later to starkeyite and amorphous MgSO 4 ‧ n H 2 O in response to a drier Mars. At Canaima, starkeyite is stable and would form during the warmer Mars summers. Due to very slow kinetics at the low Mars winter temperatures, starkeyite and amorphous MgSO 4 ‧ n H 2 O would be resistant to recrystallize to more hydrous forms and thus likely persist year‐round. During the course of analyses, starkeyite transforms into amorphous MgSO 4 ‧ n H 2 O inside the rover body due to the elevated temperature and greatly reduced relative humidity compared to the martian surface at the Canaima drill site. It is possible that crystalline sulfate minerals existed in earlier samples measured by CheMin but altered inside the rover before they could be analyzed. Starkeyite is most likely prevalent in the subsurface, whereas both starkeyite and amorphous MgSO 4 ‧ n H 2 O are likely present on the surface as starkeyite could partially transform into amorphous MgSO 4 ‧ n H 2 O due to direct solar heating.
- Open Access
- 15 May 2023
- Published by Copernicus GmbH
One Martian Year of MEDA/TIRS observations at the Mars 2020 landing site
The Thermal Infrared Sensor (TIRS; Sebastián et al., 2021; Martínez et al., 2023) is one of the six sensor packages of the Mars Environmental Dynamics Analyzer (MEDA; Rodríguez-Manfredi et al., 2021), which in turn is one of the seven science instruments on board Perseverance. Here we show a summary of TIRS scientific highlights during the first Martian year of operations. In particular, TIRS is providing the first in situ determination of the surface radiative budget, direct determination of broadband albedo and thermal inertia (Martínez et al., 2023; Savijärvi et al., 2022), and around-the-clock determination of aerosol opacities (Smith et al., 2023). In addition, TIRS is providing ground-truth to orbital retrievals of thermal inertia and albedo, as well as geophysical characterization of the uppermost surface of the regolith during Phobos and Deimos eclipses. In synergy with other instruments, TIRS is being used to determine vertical profiles of temperature (Munguira et al., 2023), to detect dust lifting from sudden changes in albedo (Vicente-Retortillo et al., 2023), and to assess changes in the water content of the Martian soil (Hausrath et al., 2023), including the potential formation of frost. TIRS observations are critical to achieve MEDA’s first programmatic objective (validate global atmospheric models by measuring the radiative surface budget in preparation for future human exploration). Also, TIRS observations are important in support of flights of Ingenuity and therefore for the design and operations of future drones. References: Hausrath, E. M. et al. (2023), The SuperCam team and the Regolith working group, An Examination of Soil Crusts on the Floor of Jezero crater, Mars, Journal of Geophysical Research: Planets (accepted). Martínez, G. M. et al. (2023), Surface Energy Budget, Albedo and Thermal Inertia at Jezero Crater, Mars, as Observed from the Mars 2020 MEDA Instrument, Journal of Geophysical Research: Planets (accepted). Munguira, A. et al. (2023), Near Surface Atmospheric Temperatures at Jezero from Mars 2020 MEDA measurements, Journal of Geophysical Research: Planets (under review). Rodriguez-Manfredi, J.A. et al. (2021), The Mars Environmental Dynamics Analyzer, MEDA. A suite of environmental sensors for the Mars 2020 mission, Spa. Sci. Rev., 217(3), 1-86. Savijärvi, H. I. et al. (2022), Surface energy fluxes and temperatures at Jezero crater, Mars, Journal of Geophysical Research: Planets: e2022JE007438. Sebastián, E. et al. (2021), Thermal calibration of the MEDA-TIRS radiometer onboard NASA's Perseverance rover, Acta Astronautica, 182,144-159. Smith, M. D. et al. (2023), Diurnal and Seasonal Variations of Aerosol Optical Depth Observed by MEDA/TIRS at Jezero Crater, Mars, Journal of Geophysical Research: Planets (accepted). Vicente-Retortillo, A. et al. (2023), Dust Lifting Through Changes in Albedo at Jezero Crater, Mars, Journal of Geophysical Research: Planets (under review).
- 15 May 2023
- Published by Copernicus GmbH
Open AccessOne Martian Year of MEDA/TIRS observations at the Mars 2020 landing site
The Thermal Infrared Sensor (TIRS; Sebastián et al., 2021; Martínez et al., 2023) is one of the six sensor packages of the Mars Environmental Dynamics Analyzer (MEDA; Rodríguez-Manfredi et al., 2021), which in turn is one of the seven science instruments on board Perseverance. Here we show a summary of TIRS scientific highlights during the first Martian year of operations. In particular, TIRS is providing the first in situ determination of the surface radiative budget, direct determination of broadband albedo and thermal inertia (Martínez et al., 2023; Savijärvi et al., 2022), and around-the-clock determination of aerosol opacities (Smith et al., 2023). In addition, TIRS is providing ground-truth to orbital retrievals of thermal inertia and albedo, as well as geophysical characterization of the uppermost surface of the regolith during Phobos and Deimos eclipses. In synergy with other instruments, TIRS is being used to determine vertical profiles of temperature (Munguira et al., 2023), to detect dust lifting from sudden changes in albedo (Vicente-Retortillo et al., 2023), and to assess changes in the water content of the Martian soil (Hausrath et al., 2023), including the potential formation of frost. TIRS observations are critical to achieve MEDA’s first programmatic objective (validate global atmospheric models by measuring the radiative surface budget in preparation for future human exploration). Also, TIRS observations are important in support of flights of Ingenuity and therefore for the design and operations of future drones. References: Hausrath, E. M. et al. (2023), The SuperCam team and the Regolith working group, An Examination of Soil Crusts on the Floor of Jezero crater, Mars, Journal of Geophysical Research: Planets (accepted). Martínez, G. M. et al. (2023), Surface Energy Budget, Albedo and Thermal Inertia at Jezero Crater, Mars, as Observed from the Mars 2020 MEDA Instrument, Journal of Geophysical Research: Planets (accepted). Munguira, A. et al. (2023), Near Surface Atmospheric Temperatures at Jezero from Mars 2020 MEDA measurements, Journal of Geophysical Research: Planets (under review). Rodriguez-Manfredi, J.A. et al. (2021), The Mars Environmental Dynamics Analyzer, MEDA. A suite of environmental sensors for the Mars 2020 mission, Spa. Sci. Rev., 217(3), 1-86. Savijärvi, H. I. et al. (2022), Surface energy fluxes and temperatures at Jezero crater, Mars, Journal of Geophysical Research: Planets: e2022JE007438. Sebastián, E. et al. (2021), Thermal calibration of the MEDA-TIRS radiometer onboard NASA's Perseverance rover, Acta Astronautica, 182,144-159. Smith, M. D. et al. (2023), Diurnal and Seasonal Variations of Aerosol Optical Depth Observed by MEDA/TIRS at Jezero Crater, Mars, Journal of Geophysical Research: Planets (accepted). Vicente-Retortillo, A. et al. (2023), Dust Lifting Through Changes in Albedo at Jezero Crater, Mars, Journal of Geophysical Research: Planets (under review).
- 13 February 2023
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 128 (2)
Initial Results of the Relative Humidity Observations by MEDA Instrument Onboard the Mars 2020 Perseverance Rover
The Mars 2020 mission rover “Perseverance”, launched on 30 July 2020 by NASA, landed successfully 18 February 2021 at Jezero Crater, Mars (Lon. E 77.4509° Lat. N 18.4446°). The landing took place at Mars solar longitude Ls = 5.2°, close to start of the northern spring. Perseverance's payload includes the relative humidity sensor MEDA HS (Mars Environmental Dynamics Analyzer Humidity Sensor), which operations, performance, and the first observations from sol 80 to sol 410 (Ls 44°–210°) of Perseverance's operations we describe. The relative humidity measured by MEDA‐HS is reliable from late night hours to few tens of minutes after sunrise when the measured humidity is greater than 2% (referenced to sensor temperature). Data delivered to the Planetary Data System include relative humidity, sensor temperature, uncertainty of relative humidity, and volume mixing ratio (VMR). VMR is calculated using the MEDA‐PS pressure sensor values. According to observations, nighttime absolute humidity follows a seasonal curve in which release of water vapor from the northern cap with advancing northern spring and summer is visible. At ground level, frost conditions may have been reached a few times during this season (Ls 44°–210°). Volume mixing ratio values show a declining diurnal trend from the midnight toward the morning suggesting adsorption of humidity into the ground. Observations are compared with an adsorptive single‐column model, which complies with observations and confirms adsorption. The model allows estimating daytime VMR levels. Short‐term subhour timescales show large temporal fluctuations in humidity, which suggest vertical and spatial advection.
- 13 February 2023
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 128 (2)
Initial Results of the Relative Humidity Observations by MEDA Instrument Onboard the Mars 2020 Perseverance Rover
The Mars 2020 mission rover “Perseverance”, launched on 30 July 2020 by NASA, landed successfully 18 February 2021 at Jezero Crater, Mars (Lon. E 77.4509° Lat. N 18.4446°). The landing took place at Mars solar longitude Ls = 5.2°, close to start of the northern spring. Perseverance's payload includes the relative humidity sensor MEDA HS (Mars Environmental Dynamics Analyzer Humidity Sensor), which operations, performance, and the first observations from sol 80 to sol 410 (Ls 44°–210°) of Perseverance's operations we describe. The relative humidity measured by MEDA‐HS is reliable from late night hours to few tens of minutes after sunrise when the measured humidity is greater than 2% (referenced to sensor temperature). Data delivered to the Planetary Data System include relative humidity, sensor temperature, uncertainty of relative humidity, and volume mixing ratio (VMR). VMR is calculated using the MEDA‐PS pressure sensor values. According to observations, nighttime absolute humidity follows a seasonal curve in which release of water vapor from the northern cap with advancing northern spring and summer is visible. At ground level, frost conditions may have been reached a few times during this season (Ls 44°–210°). Volume mixing ratio values show a declining diurnal trend from the midnight toward the morning suggesting adsorption of humidity into the ground. Observations are compared with an adsorptive single‐column model, which complies with observations and confirms adsorption. The model allows estimating daytime VMR levels. Short‐term subhour timescales show large temporal fluctuations in humidity, which suggest vertical and spatial advection.
- Open Access
- 27 January 2023
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 128 (2)
Surface Energy Budget, Albedo, and Thermal Inertia at Jezero Crater, Mars, as Observed From the Mars 2020 MEDA Instrument
The Mars Environmental Dynamics Analyzer (MEDA) on board Perseverance includes first‐of‐its‐kind sensors measuring the incident and reflected solar flux, the downwelling atmospheric IR flux, and the upwelling IR flux emitted by the surface. We use these measurements for the first 350 sols of the Mars 2020 mission (L s ∼ 6°–174° in Martian Year 36) to determine the surface radiative budget on Mars and to calculate the broadband albedo (0.3–3 μm) as a function of the illumination and viewing geometry. Together with MEDA measurements of ground temperature, we calculate the thermal inertia for homogeneous terrains without the need for numerical thermal models. We found that (a) the observed downwelling atmospheric IR flux is significantly lower than the model predictions. This is likely caused by the strong diurnal variation in aerosol opacity measured by MEDA, which is not accounted for by numerical models. (b) The albedo presents a marked non‐Lambertian behavior, with lowest values near noon and highest values corresponding to low phase angles (i.e., Sun behind the observer). (c) Thermal inertia values ranged between 180 (sand dune) and 605 (bedrock‐dominated material) SI units. (d) Averages of albedo and thermal inertia (spatial resolution of ∼3–4 m 2 ) along Perseverance's traverse are in very good agreement with collocated retrievals of thermal inertia from Thermal Emission Imaging System (spatial resolution of 100 m per pixel) and of bolometric albedo in the 0.25–2.9 μm range from (spatial resolution of ∼300 km 2 ). The results presented here are important to validate model predictions and provide ground‐truth to orbital measurements.
- 27 January 2023
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 128 (2)
Open AccessSurface Energy Budget, Albedo, and Thermal Inertia at Jezero Crater, Mars, as Observed From the Mars 2020 MEDA Instrument
The Mars Environmental Dynamics Analyzer (MEDA) on board Perseverance includes first‐of‐its‐kind sensors measuring the incident and reflected solar flux, the downwelling atmospheric IR flux, and the upwelling IR flux emitted by the surface. We use these measurements for the first 350 sols of the Mars 2020 mission (L s ∼ 6°–174° in Martian Year 36) to determine the surface radiative budget on Mars and to calculate the broadband albedo (0.3–3 μm) as a function of the illumination and viewing geometry. Together with MEDA measurements of ground temperature, we calculate the thermal inertia for homogeneous terrains without the need for numerical thermal models. We found that (a) the observed downwelling atmospheric IR flux is significantly lower than the model predictions. This is likely caused by the strong diurnal variation in aerosol opacity measured by MEDA, which is not accounted for by numerical models. (b) The albedo presents a marked non‐Lambertian behavior, with lowest values near noon and highest values corresponding to low phase angles (i.e., Sun behind the observer). (c) Thermal inertia values ranged between 180 (sand dune) and 605 (bedrock‐dominated material) SI units. (d) Averages of albedo and thermal inertia (spatial resolution of ∼3–4 m 2 ) along Perseverance's traverse are in very good agreement with collocated retrievals of thermal inertia from Thermal Emission Imaging System (spatial resolution of 100 m per pixel) and of bolometric albedo in the 0.25–2.9 μm range from (spatial resolution of ∼300 km 2 ). The results presented here are important to validate model predictions and provide ground‐truth to orbital measurements.
- Open Access
- 9 January 2023
- Published by Springer Nature in Nature Geoscience
- Vol. 16 (1) , 19-28
The diverse meteorology of Jezero crater over the first 250 sols of Perseverance on Mars
NASA’s Perseverance rover’s Mars Environmental Dynamics Analyzer is collecting data at Jezero crater, characterizing the physical processes in the lowest layer of the Martian atmosphere. Here we present measurements from the instrument’s first 250 sols of operation, revealing a spatially and temporally variable meteorology at Jezero. We find that temperature measurements at four heights capture the response of the atmospheric surface layer to multiple phenomena. We observe the transition from a stable night-time thermal inversion to a daytime, highly turbulent convective regime, with large vertical thermal gradients. Measurement of multiple daily optical depths suggests aerosol concentrations are higher in the morning than in the afternoon. Measured wind patterns are driven mainly by local topography, with a small contribution from regional winds. Daily and seasonal variability of relative humidity shows a complex hydrologic cycle. These observations suggest that changes in some local surface properties, such as surface albedo and thermal inertia, play an influential role. On a larger scale, surface pressure measurements show typical signatures of gravity waves and baroclinic eddies in a part of the seasonal cycle previously characterized as low wave activity. These observations, both combined and simultaneous, unveil the diversity of processes driving change on today’s Martian surface at Jezero crater.
- 9 January 2023
- Published by Springer Nature in Nature Geoscience
- Vol. 16 (1) , 19-28
Open AccessThe diverse meteorology of Jezero crater over the first 250 sols of Perseverance on Mars
NASA’s Perseverance rover’s Mars Environmental Dynamics Analyzer is collecting data at Jezero crater, characterizing the physical processes in the lowest layer of the Martian atmosphere. Here we present measurements from the instrument’s first 250 sols of operation, revealing a spatially and temporally variable meteorology at Jezero. We find that temperature measurements at four heights capture the response of the atmospheric surface layer to multiple phenomena. We observe the transition from a stable night-time thermal inversion to a daytime, highly turbulent convective regime, with large vertical thermal gradients. Measurement of multiple daily optical depths suggests aerosol concentrations are higher in the morning than in the afternoon. Measured wind patterns are driven mainly by local topography, with a small contribution from regional winds. Daily and seasonal variability of relative humidity shows a complex hydrologic cycle. These observations suggest that changes in some local surface properties, such as surface albedo and thermal inertia, play an influential role. On a larger scale, surface pressure measurements show typical signatures of gravity waves and baroclinic eddies in a part of the seasonal cycle previously characterized as low wave activity. These observations, both combined and simultaneous, unveil the diversity of processes driving change on today’s Martian surface at Jezero crater.
- Open Access
- 16 November 2022
- Published by Wiley in ESS Open Archive
MEDA HS: Relative humidity sensor for the Mars 2020 Perseverance rover
The Finnish Meteorological Institute (FMI) provides a relative humidity measurement sensor (HS) for NASA’s Mars 2020 rover. The sensor is a part of the Mars Environmental Dynamic Analyzer (MEDA), a suite of environmental sensors provided by Spain’s Centro de Astrobiología. The main scientific goal of the humidity sensor is to measure the relative humidity of the Martian atmosphere near the surface and to complement previous Mars mission atmospheric measurements for a better understanding of Martian atmospheric conditions and the hydrological cycle. Relative humidity has been measured from the surface of Mars previously by Phoenix and Curiosity. Compared to the relative humidity sensor on board Curiosity, the MEDA HS is based on a new version of the polymeric capacitive humidity sensor heads developed by Vaisala. Calibration of humidity devices for Mars conditions is challenging and new methods have been developed for MEDA HS. Calibration and test campaigns have been performed at the FMI, at University of Michigan and the German Aerospace Center (DLR) in Berlin to achieve the best possible calibration. The accuracy of HS and uncertainty of the calibration has been also analysed in detail with VTT Technical Research Centre of Finland. Assessment of sensor performance after landing on Mars confirms that the calibration has been successful, and the HS is delivering high quality data for the science community.
- 16 November 2022
- Published by Wiley in ESS Open Archive
Open AccessMEDA HS: Relative humidity sensor for the Mars 2020 Perseverance rover
The Finnish Meteorological Institute (FMI) provides a relative humidity measurement sensor (HS) for NASA’s Mars 2020 rover. The sensor is a part of the Mars Environmental Dynamic Analyzer (MEDA), a suite of environmental sensors provided by Spain’s Centro de Astrobiología. The main scientific goal of the humidity sensor is to measure the relative humidity of the Martian atmosphere near the surface and to complement previous Mars mission atmospheric measurements for a better understanding of Martian atmospheric conditions and the hydrological cycle. Relative humidity has been measured from the surface of Mars previously by Phoenix and Curiosity. Compared to the relative humidity sensor on board Curiosity, the MEDA HS is based on a new version of the polymeric capacitive humidity sensor heads developed by Vaisala. Calibration of humidity devices for Mars conditions is challenging and new methods have been developed for MEDA HS. Calibration and test campaigns have been performed at the FMI, at University of Michigan and the German Aerospace Center (DLR) in Berlin to achieve the best possible calibration. The accuracy of HS and uncertainty of the calibration has been also analysed in detail with VTT Technical Research Centre of Finland. Assessment of sensor performance after landing on Mars confirms that the calibration has been successful, and the HS is delivering high quality data for the science community.
- Open Access
- 24 August 2022
- Published by Wiley in ESS Open Archive
Surface Energy Budget, Albedo and Thermal Inertia at Jezero Crater, Mars, as Observed from the Mars 2020 MEDA Instrument
The Mars Environmental Dynamics Analyzer (MEDA) on board Perseverance includes first-of-their-kind sensors measuring the incident and reflected solar flux, the downwelling atmospheric IR flux, and the upwelling IR flux emitted by the surface. We use these measurements for the first 350 sols of the Mars 2020 mission (Ls ~ 6-174 deg; in Martian Year 36) to determine the surface radiative budget on Mars, and to calculate the broadband albedo (0.3-3 μm) as a function of the illumination and viewing geometry. Together with MEDA measurements of ground temperature, we calculate the thermal inertia for homogeneous terrains without the need for numerical models. We found that: (1) the observed downwelling atmospheric IR flux is significantly lower than model predictions. This is likely caused by the strong diurnal variation in aerosol opacity measured by MEDA, which is not accounted for by numerical models. (2) The albedo presents a marked non-Lambertian behavior, with lowest values near noon and highest values corresponding to low phase angles (i.e., Sun behind the observer). (3) Thermal inertia values ranged between 180 (sand dune) and 605 (bedrock-dominated material) SI units. (4) Averages across Perseverance’ traverse of albedo and thermal inertia (spatial resolution of ~3-4 m2) are in very good agreement with collocated retrievals of thermal inertia from THEMIS (spatial resolution of 100 m per pixel) and of bolometric albedo in the 0.25-2.9 μm range from (spatial resolution of ~300 km2). The results presented here are important to validate model predictions and provide ground-truth to orbital measurements.
- 24 August 2022
- Published by Wiley in ESS Open Archive
Open AccessSurface Energy Budget, Albedo and Thermal Inertia at Jezero Crater, Mars, as Observed from the Mars 2020 MEDA Instrument
The Mars Environmental Dynamics Analyzer (MEDA) on board Perseverance includes first-of-their-kind sensors measuring the incident and reflected solar flux, the downwelling atmospheric IR flux, and the upwelling IR flux emitted by the surface. We use these measurements for the first 350 sols of the Mars 2020 mission (Ls ~ 6-174 deg; in Martian Year 36) to determine the surface radiative budget on Mars, and to calculate the broadband albedo (0.3-3 μm) as a function of the illumination and viewing geometry. Together with MEDA measurements of ground temperature, we calculate the thermal inertia for homogeneous terrains without the need for numerical models. We found that: (1) the observed downwelling atmospheric IR flux is significantly lower than model predictions. This is likely caused by the strong diurnal variation in aerosol opacity measured by MEDA, which is not accounted for by numerical models. (2) The albedo presents a marked non-Lambertian behavior, with lowest values near noon and highest values corresponding to low phase angles (i.e., Sun behind the observer). (3) Thermal inertia values ranged between 180 (sand dune) and 605 (bedrock-dominated material) SI units. (4) Averages across Perseverance’ traverse of albedo and thermal inertia (spatial resolution of ~3-4 m2) are in very good agreement with collocated retrievals of thermal inertia from THEMIS (spatial resolution of 100 m per pixel) and of bolometric albedo in the 0.25-2.9 μm range from (spatial resolution of ~300 km2). The results presented here are important to validate model predictions and provide ground-truth to orbital measurements.
- Open Access
- 22 June 2022
- Published by Springer Nature in Research Square
The rich meteorology of Jezero crater over the first 250 sols of Perseverance on Mars
Perseverance's Mars Environmental Dynamics Analyzer (MEDA) is collecting data at Jezero Crater, characterizing the physical processes in the lowest layer of the atmosphere as no previous instrument did before. Here we show that temperature measurements at four heights capture the response of the atmospheric surface layer to multiple phenomena. We observe the transition from a stable nighttime thermal inversion to a diurnal, highly turbulent convective regime, with large vertical thermal gradients, and where local surface properties (such as Thermal Inertia) play an essential role. Recording multiple daily optical depths yielded higher aerosol concentrations in the morning than in the afternoon. Measured wind patterns are mainly driven by local topography, with a small contribution from regional winds. Daily and seasonal variability of relative humidity shows a complex hydrologic cycle. These observations raise new puzzles in which changes in surface albedo and thermal inertia may play an influential role. On a larger scale, surface pressure shows typical signatures of gravity waves and baroclinic eddies in a part of the seasonal cycle characterized before as low wave activity. These observations, combined and simultaneous, show the rich Jezero’s meteorology, and unveil the diversity of processes driving change on today’s Martian surface.
- 22 June 2022
- Published by Springer Nature in Research Square
Open AccessThe rich meteorology of Jezero crater over the first 250 sols of Perseverance on Mars
Perseverance's Mars Environmental Dynamics Analyzer (MEDA) is collecting data at Jezero Crater, characterizing the physical processes in the lowest layer of the atmosphere as no previous instrument did before. Here we show that temperature measurements at four heights capture the response of the atmospheric surface layer to multiple phenomena. We observe the transition from a stable nighttime thermal inversion to a diurnal, highly turbulent convective regime, with large vertical thermal gradients, and where local surface properties (such as Thermal Inertia) play an essential role. Recording multiple daily optical depths yielded higher aerosol concentrations in the morning than in the afternoon. Measured wind patterns are mainly driven by local topography, with a small contribution from regional winds. Daily and seasonal variability of relative humidity shows a complex hydrologic cycle. These observations raise new puzzles in which changes in surface albedo and thermal inertia may play an influential role. On a larger scale, surface pressure shows typical signatures of gravity waves and baroclinic eddies in a part of the seasonal cycle characterized before as low wave activity. These observations, combined and simultaneous, show the rich Jezero’s meteorology, and unveil the diversity of processes driving change on today’s Martian surface.