Stefanos Gkatzogiannis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Stefanos Gkatzogiannis has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Thomas Ummenhofer
Steel & Lightweight Structures, Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
7 shared publicationsPeter Knoedel
Karlsruhe Institute of Technology - KIT Steel & Lightweight Structures - Research Center for Steel, Timber & Masonry, Karsrluhe, Germany
6 shared publications- Jan Schubnell
Fraunhofer Institute for Mechanics of Materials IWM, Freiburg, Germany
2 shared publications - Marios C. Phocas
Department of Architecture, Faculty of Engineering, University of Cyprus, Nicosia, Cyprus
2 shared publications Ayhan Ince
1 shared publication- Bo Li
Northwestern Polytechnical University
1 shared publication
Latest Publications
- 20 September 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 215
Recent advances in HFMI treatment for fatigue strength enhancement of welded joints: a review
- 20 September 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 215
Recent advances in HFMI treatment for fatigue strength enhancement of welded joints: a review
- 1 September 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 32 (3) , 04026020
Reconfigurable Circular Building Structure with Reduced Number of Actuators
Reconfigurable building structures may obtain different shapes depending on varying functional, environmental, and/or external loading conditions. Their capability to adapt through shape tr...
- 1 September 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Architectural Engineering
- Vol. 32 (3) , 04026020
Reconfigurable Circular Building Structure with Reduced Number of Actuators
Reconfigurable building structures may obtain different shapes depending on varying functional, environmental, and/or external loading conditions. Their capability to adapt through shape tr...
- 15 December 2025
- Published by Elsevier in Engineering Structures
- Vol. 350
Structurally optimized design for adjustable joints of lightweight reconfigurable structures based on finite element analysis
- 15 December 2025
- Published by Elsevier in Engineering Structures
- Vol. 350
Structurally optimized design for adjustable joints of lightweight reconfigurable structures based on finite element analysis
- Open Access
Reuse of Decommissioned Tubular Steel Wind Turbine Towers: General Considerations and Two Case Studies
Nowadays, the circular economy is driving the construction industry towards greater sustainability for both environmental and financial purposes. One prominent area of research with significant contributions to circular economy is the reuse of steel from decommissioned structures in new construction projects. This approach is deemed far more efficient than ordinary steel recycling, due to the fact that it contributes towards reducing both the cost of the new project and the associated carbon emissions. Along these lines, the feasibility of utilizing steel wind turbine towers (WTTs) as part of a new structure is investigated herein, considering that wind turbines are decommissioned after a nominal life of approximately 25 years due to fatigue limitations. General principles of structural steel reuse are first presented in a systematic manner, followed by two case studies. Realistic data about the geometry and cross-sections of previous generation models of WTTs were obtained from the Greek Center for Renewable Energy Sources and Savings (CRES), including drawings and photographic material from their demonstrative wind farm in the area of Keratea. A specific wind turbine was selected that is about to exceed its life expectancy and will soon be decommissioned. Two alternative applications for the reuse of the tower were proposed and analyzed, with emphasis on the structural aspects. One deals with the use of parts of the tower as a small-span pedestrian bridge, while the second addresses the transformation of a tower section into a water storage tank. Several decision factors have contributed to the selection of these two reuse scenarios, including, amongst others, the geometric compatibility of the decommissioned wind turbine tower with the proposed applications, engineering intuition about the tower having adequate strength for its new role, the potential to minimize fatigue loads in the reused state, the minimization of cutting and joining processes as much as possible to restrain further CO2 emissions, reduction in waste material, the societal contribution of the potential reuse applications, etc. The two examples are briefly presented, aiming to demonstrate the concept and feasibility at the preliminary design level, highlighting the potential of decommissioned WTTs to find proper use for their future life.
Open AccessReuse of Decommissioned Tubular Steel Wind Turbine Towers: General Considerations and Two Case Studies
Nowadays, the circular economy is driving the construction industry towards greater sustainability for both environmental and financial purposes. One prominent area of research with significant contributions to circular economy is the reuse of steel from decommissioned structures in new construction projects. This approach is deemed far more efficient than ordinary steel recycling, due to the fact that it contributes towards reducing both the cost of the new project and the associated carbon emissions. Along these lines, the feasibility of utilizing steel wind turbine towers (WTTs) as part of a new structure is investigated herein, considering that wind turbines are decommissioned after a nominal life of approximately 25 years due to fatigue limitations. General principles of structural steel reuse are first presented in a systematic manner, followed by two case studies. Realistic data about the geometry and cross-sections of previous generation models of WTTs were obtained from the Greek Center for Renewable Energy Sources and Savings (CRES), including drawings and photographic material from their demonstrative wind farm in the area of Keratea. A specific wind turbine was selected that is about to exceed its life expectancy and will soon be decommissioned. Two alternative applications for the reuse of the tower were proposed and analyzed, with emphasis on the structural aspects. One deals with the use of parts of the tower as a small-span pedestrian bridge, while the second addresses the transformation of a tower section into a water storage tank. Several decision factors have contributed to the selection of these two reuse scenarios, including, amongst others, the geometric compatibility of the decommissioned wind turbine tower with the proposed applications, engineering intuition about the tower having adequate strength for its new role, the potential to minimize fatigue loads in the reused state, the minimization of cutting and joining processes as much as possible to restrain further CO2 emissions, reduction in waste material, the societal contribution of the potential reuse applications, etc. The two examples are briefly presented, aiming to demonstrate the concept and feasibility at the preliminary design level, highlighting the potential of decommissioned WTTs to find proper use for their future life.
- Open Access
- 7 May 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (6) , 1107-1117
Residual stress relaxation in HFMI-treated fillet welds after single overload peaks
The induction of near-surface compressive residual stress is an important factor for fatigue life improvement of HFMI-treated welded joints. However, the relaxation of these beneficial residual stresses under single overload peaks under variable amplitude and service loads may significantly reduce fatigue life improvement. For this reason, several recommendations exist to limit the maximum applied load stress for this kind of post-treated welded joints. In this work, the effect of single tension and compression overloads on the relaxation behavior of HFMI-induced residual stresses was studied experimentally by means of X-ray and neutron diffraction techniques complemented by numerical simulation at transverse stiffeners made of mild S355J2 steel and high strength S960QL steel. Loads were applied close to the real yield strength of the base material. Significantly different relaxation behavior was observed for S355J2 and S960QL steel. Furthermore, high compression loads lead to full residual stress relaxation at the weld toe of S960QL and moderate relaxation for S355J2. High tension loads lead only to slight relaxation.
- 7 May 2020
- Published by Springer Nature in Welding in the World
- Vol. 64 (6) , 1107-1117
Open AccessResidual stress relaxation in HFMI-treated fillet welds after single overload peaks
The induction of near-surface compressive residual stress is an important factor for fatigue life improvement of HFMI-treated welded joints. However, the relaxation of these beneficial residual stresses under single overload peaks under variable amplitude and service loads may significantly reduce fatigue life improvement. For this reason, several recommendations exist to limit the maximum applied load stress for this kind of post-treated welded joints. In this work, the effect of single tension and compression overloads on the relaxation behavior of HFMI-induced residual stresses was studied experimentally by means of X-ray and neutron diffraction techniques complemented by numerical simulation at transverse stiffeners made of mild S355J2 steel and high strength S960QL steel. Loads were applied close to the real yield strength of the base material. Significantly different relaxation behavior was observed for S355J2 and S960QL steel. Furthermore, high compression loads lead to full residual stress relaxation at the weld toe of S960QL and moderate relaxation for S355J2. High tension loads lead only to slight relaxation.
- Open Access
- 4 May 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (8) , 4879-4887
Calibration of High-Frequency Mechanical Impact Simulation Based on Drop Tests
A series of drop tests was implemented in the present study in order to allow the reproduction of a single impact identical to the high frequency mechanical impact (HFMI) under monitored conditions in the laboratory. Therewith, characterization of the investigated material’s mechanical behavior by explicitly considering possible irregularities concerning the present deformation modes would be enabled. Main goal was the determination of the investigated material’s dynamic yield stress for various strain rates inside the spectrum of interest, so that the Cowper–Symonds viscous material model would be calibrated for the subsequent HFMI simulation. The values of the dynamic yield stress extracted by the present drop tests show good agreement with other experimental methods regarding the investigated material S355. The introduction of the calibrated material behavior on the present drop tests in the finite element (FE) analysis of HFMI led to reduced preciseness though, in comparison with the FE analysis, which considered high strain rate tensile tests found in literature. A series of conclusions was drawn from both the experimental and numerical investigations, confirming most of the initial expectations. Further work is proposed, in order to clarify an incompatibility met during the numerical investigations.
- 4 May 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 29 (8) , 4879-4887
Open AccessCalibration of High-Frequency Mechanical Impact Simulation Based on Drop Tests
A series of drop tests was implemented in the present study in order to allow the reproduction of a single impact identical to the high frequency mechanical impact (HFMI) under monitored conditions in the laboratory. Therewith, characterization of the investigated material’s mechanical behavior by explicitly considering possible irregularities concerning the present deformation modes would be enabled. Main goal was the determination of the investigated material’s dynamic yield stress for various strain rates inside the spectrum of interest, so that the Cowper–Symonds viscous material model would be calibrated for the subsequent HFMI simulation. The values of the dynamic yield stress extracted by the present drop tests show good agreement with other experimental methods regarding the investigated material S355. The introduction of the calibrated material behavior on the present drop tests in the finite element (FE) analysis of HFMI led to reduced preciseness though, in comparison with the FE analysis, which considered high strain rate tensile tests found in literature. A series of conclusions was drawn from both the experimental and numerical investigations, confirming most of the initial expectations. Further work is proposed, in order to clarify an incompatibility met during the numerical investigations.
- Open Access
FE Simulation of High Frequency Mechanical Impact (HFMI) Treatment – First Results
High Frequency Mechanical Impact treatment is investigated numerically in the present paper. A first‐step numerical dynamic analysis is carried out using the solver LS‐Dyna. The treatment of an unnotched component of S355 is simulated. The strain rate dependent material parameter Cowper‐Symonds is calibrated for the investigated material based on data from literature. Goal of the present analysis is to act a first step for a robust engineering approach, which will calculate with sufficient preciseness the residual stresses introduced by this post‐weld treatment. The calculated residual stresses of the present investigation are compared with respective measurements found in literature. Deviation between measured and simulated residual stresses indicates the need for further improvement of the present model.
Open AccessFE Simulation of High Frequency Mechanical Impact (HFMI) Treatment – First Results
High Frequency Mechanical Impact treatment is investigated numerically in the present paper. A first‐step numerical dynamic analysis is carried out using the solver LS‐Dyna. The treatment of an unnotched component of S355 is simulated. The strain rate dependent material parameter Cowper‐Symonds is calibrated for the investigated material based on data from literature. Goal of the present analysis is to act a first step for a robust engineering approach, which will calculate with sufficient preciseness the residual stresses introduced by this post‐weld treatment. The calculated residual stresses of the present investigation are compared with respective measurements found in literature. Deviation between measured and simulated residual stresses indicates the need for further improvement of the present model.
- 1 September 2019
- Published by Elsevier in International Journal of Fatigue
- Vol. 126, 90-102
Correlation of laboratory and real marine corrosion for the investigation of corrosion fatigue behaviour of steel components
- 1 September 2019
- Published by Elsevier in International Journal of Fatigue
- Vol. 126, 90-102
Correlation of laboratory and real marine corrosion for the investigation of corrosion fatigue behaviour of steel components
- 25 May 2018
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 27 (10) , 5079-5085
Strain Rate Dependency of Simulated Welding Residual Stresses
- 25 May 2018
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 27 (10) , 5079-5085
Strain Rate Dependency of Simulated Welding Residual Stresses
02.02: FE welding residual stress simulation: Influence of boundary conditions and material models
A series of finite element weld simulations was carried out for single‐pass welds. Two multi‐phase ferritic steel grades with yield strength of 355 MPa were investigated. Methods for selecting efficiently the boundary conditions of unrestrained and clamped‐down plates were simulated with satisfying results. Furthermore, the influence of the tangent modulus, the coefficient for thermal expansion and the applied model of hardening behaviour on the final field of calculated welding residual stresses (WRS) was analysed. Values, which provide better agreement with experimental results, along with those that lie on the safe side were highlighted.
02.02: FE welding residual stress simulation: Influence of boundary conditions and material models
A series of finite element weld simulations was carried out for single‐pass welds. Two multi‐phase ferritic steel grades with yield strength of 355 MPa were investigated. Methods for selecting efficiently the boundary conditions of unrestrained and clamped‐down plates were simulated with satisfying results. Furthermore, the influence of the tangent modulus, the coefficient for thermal expansion and the applied model of hardening behaviour on the final field of calculated welding residual stresses (WRS) was analysed. Values, which provide better agreement with experimental results, along with those that lie on the safe side were highlighted.