Vincent Keryvin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Vincent Keryvin has a total of 180 co-authors. Here are the top co-authors by number of shared publications:
Tanguy Rouxel
12 shared publications- Cedric Bernard
Université Européenne de Bretagne, Université de Bretagne-Sud
11 shared publications L. Charleux
9 shared publicationsP.-Y. Mechin
9 shared publicationsT. Rouxel
8 shared publicationsJ.-C. Grandidier
7 shared publications
Latest Publications
- Open Access
- 31 October 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 213
Transition from mesoscale instability to fibre strength controlled compression failure in carbon fibre composites
- 31 October 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 213
Open AccessTransition from mesoscale instability to fibre strength controlled compression failure in carbon fibre composites
- Open Access
- 9 May 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 208
Extracting wood elastic constants at the level of the cell wall layers by nano-indentation with atomic force microscopy
- 9 May 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 208
Open AccessExtracting wood elastic constants at the level of the cell wall layers by nano-indentation with atomic force microscopy
- Open Access
- 22 April 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 207
Compressive strength of continuous high-modulus carbon fibre reinforced epoxy composites
- 22 April 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 207
Open AccessCompressive strength of continuous high-modulus carbon fibre reinforced epoxy composites
- Open Access
- 21 November 2025
- Published by Elsevier in Journal of Ocean Engineering and Science
- Vol. 11 (4) , 1072-1094
On the use of relevant models and analyses for the structural mast design of America’s Cup racing yachts (AC75)
- 21 November 2025
- Published by Elsevier in Journal of Ocean Engineering and Science
- Vol. 11 (4) , 1072-1094
Open AccessOn the use of relevant models and analyses for the structural mast design of America’s Cup racing yachts (AC75)
- Open Access
- 25 September 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 309
An experimental method for determining the in-plane shear modulus of carbon fibres
- 25 September 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 309
Open AccessAn experimental method for determining the in-plane shear modulus of carbon fibres
- Open Access
- 6 September 2025
- Published by Elsevier in Composites Science and Technology
- Vol. 272
Assessing the validity of micro-pillar compression for determining strength and stiffness of carbon fibres
- 6 September 2025
- Published by Elsevier in Composites Science and Technology
- Vol. 272
Open AccessAssessing the validity of micro-pillar compression for determining strength and stiffness of carbon fibres
- Open Access
- 29 April 2025
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 196
Estimation of compressive strength in thick continuous fibre composites: Quantifying the role of initial fibre misalignment
- 29 April 2025
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 196
Open AccessEstimation of compressive strength in thick continuous fibre composites: Quantifying the role of initial fibre misalignment
- 12 November 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (6) , 793-805
A unified method to generate representative volume elements with tailored random fibre arrangements to estimate the shear and transverse behaviours of unidirectional continuous fibres composite plies
Axial compressible strength is a key design parameter of CFRP laminate structures, especially for Aerospace where maximum flexure on wings is driven by the global margin of safety on compressive loads. One of its main limiting contributors is the non-linear shear behaviour of the unidirectional ply. This shear response can be predicted by using generated (quasi-)random microstructures set within representative volume elements (RVE). Different microstructures with or without clusters of fibres (resulting from manufacturing processes) are necessary to quantify the mechanical variability. The variability of the microstructures is characterised by the variation of the arrangement, the volume fraction and the misalignment of the fibres. This leads to significant variations in the mechanical performance, in particular for the shear behaviour. In this study, we propose a unified algorithm that makes it possible to generate all the different positions of fibres in microstructures with very high fibre volume fractions. The microstructural parameters responsible for variations in mechanical behaviour are identified to establish a correlation between fibre distribution and the mechanical response. Finally, a composite cross-section is analysed to estimate the local non-linear shear behaviour as well as the compressive strength as an example to illustrate the benefit of complex microstructures modelling.
- 12 November 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (6) , 793-805
A unified method to generate representative volume elements with tailored random fibre arrangements to estimate the shear and transverse behaviours of unidirectional continuous fibres composite plies
Axial compressible strength is a key design parameter of CFRP laminate structures, especially for Aerospace where maximum flexure on wings is driven by the global margin of safety on compressive loads. One of its main limiting contributors is the non-linear shear behaviour of the unidirectional ply. This shear response can be predicted by using generated (quasi-)random microstructures set within representative volume elements (RVE). Different microstructures with or without clusters of fibres (resulting from manufacturing processes) are necessary to quantify the mechanical variability. The variability of the microstructures is characterised by the variation of the arrangement, the volume fraction and the misalignment of the fibres. This leads to significant variations in the mechanical performance, in particular for the shear behaviour. In this study, we propose a unified algorithm that makes it possible to generate all the different positions of fibres in microstructures with very high fibre volume fractions. The microstructural parameters responsible for variations in mechanical behaviour are identified to establish a correlation between fibre distribution and the mechanical response. Finally, a composite cross-section is analysed to estimate the local non-linear shear behaviour as well as the compressive strength as an example to illustrate the benefit of complex microstructures modelling.
- Open Access
- 17 September 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 287
Counter-intuitive effect of the degree of cure of epoxy resins on the compressive strength of continuous fibre composites
- 17 September 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 287
Open AccessCounter-intuitive effect of the degree of cure of epoxy resins on the compressive strength of continuous fibre composites