SKShahriyar Kaboli

Shahriyar Kaboli

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Shahriyar Kaboli has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • An Extremely Low Ripple High-Voltage DC Power Supply System for Depressed Collector Traveling-Wave Tubes

    by Mojtaba Ziaoddini, Shahriyar Kaboli

    This article investigates the impact of isolating transformer stray capacitances on the output voltage ripple of the high-voltage dc power supply system used in depressed collector traveling-wave tubes (TWTs). It is shown that the common-mode (CM) capacitive current from the isolating transformer of the TWT’s depressed collector power supply passes through the output of the TWT’s cathode power supply. Therefore, an additional ripple is generated at the output of the cathode power supply. In high-voltage applications, adding filters to reduce ripple conflicts with the protection considerations of the load and the power supply. This study focuses on reducing this extra voltage ripple without adding new filters. An analysis is presented to demonstrate the relationship between the voltage ripple of the TWT’s cathode power supply and the stray capacitances of the isolating transformer. A transformer winding structure is then proposed to eliminate the CM capacitive current of the collector power supply. Simulation and experimental results show that using the proposed transformer winding structure leads to a 90% voltage ripple amplitude reduction at the cathode power supply output.


  • A Distributed Turn-Off Delay Compensator Scheme for Voltage Balancing of Series-Connected IGBTs

    by Mostafa Zarghani, Francesco Iannuzzo, Frede Blaabjerg, Shahriyar Kaboli

    This paper presents a voltage balancing scheme for Series-Connected IGBTs (SCIs) using a turn-off delay compensator. In SCIs, inherent synchronization challenges and parasitic capacitances lead to uneven voltage distribution and potential over-voltage conditions. Traditional time delay adjustment methods adjusting both turn-on and turn-off delays involve complex circuitry, difficult for numerous SCIs. The paper examines factors affecting voltage imbalances during turn-on and turn-off transitions, revealing that turn-off imbalances are more critical. Therefore, a straightforward approach is introduced for turn-off delay compensation, eliminating the need for high bandwidth and isolated feedbacks. Additionally, in the proposed scheme, by locally adjusting the turn-off delay time for each switch, obviating the necessity for separate command signals. Consequently, this pragmatic scheme is especially well-suited for applications where the complexity becomes a hindrance to expanding the number of series-connected switches. Simulation and experiments involving four IGBTs within a 2.4 kV system demonstrate a voltage balancing accuracy of less than 20 V.


  • Research on the Effect of Transients of High-Voltage Power Supplies on the Lifetime of High-Power Vacuum Tubes: A Microscopic Assessment

    by Shahriyar Kaboli, Mojtaba Ziaoddini

    Electron guns are used as the electron sources in high-power electron tubes. The generated electron beam in electric guns passes through an aperture at the center of the anode. Since the electron beam has considerable kinetic energy, any collision between the electron beam and the anode aperture edge damages the electron gun. Therefore, electron guns are designed to meet the compatibility between the diameters of the electron beam and the anode aperture. However, this compatibility is disrupted during the transient time interval of the gun’s power supply. In this article, the cause of failure of the electron gun of high-power electron tubes is investigated for the transient interval of the gun’s power supply. The investigations are carried out on a damaged anode; new experiments and computer simulations are also employed. The microscopic assessment shows the studied anode melted several times, proving the role of power supply transients in the failure of the studied gun. Numerical analyses are presented to verify the result of the microscopic assessments. The numerical analysis is carried out using the finite element method (FEM). The result of this study can provide information for proposing the appropriate transient interval of the vacuum tube’s high-voltage power supplies.

  • Voltage Balancing of Series IGBTs in Short-Circuit Conditions

    by Mostafa Zarghani, Saeed Peyghami, Francesco Iannuzzo, Frede Blaabjerg, Shahriyar Kaboli

    This article proposes a scheme for balancing the voltage of series-connected insulated gate bipolar transistors (IGBTs), which is also very effective under short-circuit conditions. An optimized clamp-mode snubber is proposed, including an active-driver to balance the currents of the IGBTs during short-circuit, which in turn allows for a considerable reduction of the snubber capacitance. The approach is proven to be effective under short-circuit conditions by a maximum of 55 V voltage increment and a negligible difference in the current values. The effectiveness of the proposed approach is demonstrated through simulations in PSPICE software and experimental tests performed at 2 kV.


  • An IGBT-Based High-Voltage Crowbar for Minimizing the Fault Current Interruption Time and Injected Fault Energy During the Vacuum Arc Fault in Microwave Tubes

    by Kaveh Pouresmaeil, Shahriyar Kaboli

    In conventional high-voltage power supplies used for driving the microwave tubes, the shunt crowbar, which generally consists of series-connected thyristors, protects the microwave tube against the vacuum arc fault. In the case of arc fault, the thyristor-based crowbar is closed as a parallel path and diverts the fault current through itself. It avoids serious damage to the microwave tube. However, thyristor switches usually have a limited rate of rise of ON-state current (di/dt), which necessitates placing a series inductor in the crowbar path. Thus, satisfying all protection limits of microwave tubes--including the injected fault energy and the fault current interruption time--is a challenging task for the thyristor-based crowbar. In this article, an insulated-gate bipolar transistor (IGBT)-based crowbar is employed to overcome this problem. Taking the advantages of IGBT switches, the proposed crowbar satisfies all the protection limits of the microwave tubes. Theoretical analysis, simulation studies, and experimental tests are utilized to compare the crowbar performance in the presence of the conventional crowbar and the IGBT-based crowbar.


  • A Microscopic Assessment About the Fracture of Alumina in the Pillbox-Type RF Window of High-Power Electron Tubes

    by Shahriyar Kaboli

    Alumina is widely used as a vacuum ceramic separator in the pillbox-type output window of high-power electron tubes. The fracture of alumina is one of the most important factors in the failure of these tubes. In this article, the fracture process of alumina in the pillbox-type window of high-power electron tubes is assessed microscopically. The investigation shows the twinning phenomenon in the fractured alumina. The reason for initiating and propagating twins is also investigated. An increase in the alumina temperature decreases the required stress level for generating twins. The overheating condition occurs due to an impedance mismatch in the pillbox-type window. Experimental and numerical analyses are presented to verify the mechanism of mechanical stress due to the overheating condition. The numerical analysis is carried out by the finite-element method (FEM). The result of this study can provide information for proposing a temperature monitoring scheme to turn off the tube before reaching the overheating condition.


  • A Series Stacked IGBT Switch to Be Used as a Fault Current Limiter in HV High-Power Supplies

    by Sadegh Mohsenzade, Mostafa Zarghani, Shahriyar Kaboli

    The safe operating condition for the vacuum tubes is very important and critical since they are very expensive and delicate. Providing limited short circuit energy for the vacuum tube and fast transferring from the short circuit to the nominal operation state are absolutely necessary. Extant protection strategies threat the availability of the vacuum tubes. In addition, they cannot completely protect the tube due to the delay of the fault detection system. This paper proposes a high voltage (HV) short circuit fault current limiter which can limit the short circuit energy of the system inherently. The proposed structure activates automatically when the current exceeds the predetermined value. Hence, the need for the fault detection unit is minimized. The proposed short circuit fault current limiter is based on the series insulated gate bipolar transistors (IGBTs). Due to the interesting current limiting feature of the IGBTs, the short circuit current is limited for a definite time. During this time interval, the vacuum arc interrupts and the tube can operate instantaneously. In order to provide a safe operating condition of the series-connected IGBTs in the short circuit fault, several external circuits are suggested. The proper operation of the proposed short circuit fault current limiter is evaluated using simulations and experimental prototyping.


  • A Fast Vacuum Arc Detection Method Based on the Neural Network Data Fusion Algorithm for the High-Voltage DC Power Supply of Vacuum Tubes

    by Ramin Ayoubi, Shahriyar Kaboli

    Vacuum arc is one of the most important failure factors of the vacuum tubes. The amount of delivered energy from the high-voltage dc power supply to the vacuum tube is an important issue during the vacuum arc in the tube. Vacuum arc acts as a short-circuit fault (SCF) at the power supply output. The majority of converters use a single current sensor to measure only the converter output current for detecting the SCF. However, the sensor may provide unreliable data because of the noise effect. Application of a low-pass filter reduces the noise effect. Regarding the delay of the low-pass filter, the interval of arc detection increases and more energy is delivered to the tube. In this article, a fast vacuum arc diagnosis system is proposed based on the neural network data fusion algorithm. The proposed scheme consists of two sensors: the conventional current sensor and the existing voltage sensor used for controlling and monitoring. The data of these two sensors are combined by neural networks to diagnose the vacuum arc and to reject false alarms in noisy environments. The proposed method has a fast response time to the real SCFs while it remains inactive against the false data which are generated by noise. Simulations and experimental tests are carried out to evaluate the proposed scheme.


  • A Very Low-Ripple High-Voltage High-Power DC Power Supply Using an Interleaved Converter and a Linear Ripple Elimination Unit

    by Mostafa Zarghani, Sadegh Mohsenzade, Shahriyar Kaboli

    High voltage DC power supplies (HVDCPS) have been widely adopted for the vacuum tubes. In this application field, the low ripple voltage cannot be easily achieved by increasing the size of the output capacitance of the HVDCPS due to the limited permissible level of the stored energy. To obtain a low level of the output ripple as well as the limited value of the stored energy, the previously published literature proposed switching frequency increment. This approach has several shortcomings such as switching power loss increment, a limited level of the achievable ripple, and low value of the insulators lifetime. To improve the mentioned deficiencies, this paper hybridizes the series linear regulator and a high-frequency high-power DC interleaved converter. Using the proposed method, at the first stage, the level of the ripple decreases to a rational margin with increasing the ripple frequency. At the second stage, the level of the ripple reduces using the linear regulator to reach the expected precision. In order to validate the performance of the proposed structure, simulation and experimental results are provided for a 15 kV and 22.5 kW converter with the output voltage precision of 0.02%.


  • A Voltage Balancing Method for Series-Connected IGBTs Operating as a Fault Current Limiter in High-Voltage DC Power Supplies

    by Sadegh Mohsenzade, Mostafa Zarghani, Shahriyar Kaboli

    This article proposes a high-voltage fault current limiter (HVFCL) for high-voltage dc power supplies (HVdcPSs) which limits the current of the power supply automatically in the short-circuit fault (SCF). The proposed HVFCL is based on the series-connected insulated gate bipolar transistors (IGBTs). The main achievements of this article are the balanced voltage sharing and a very low value of the short-circuit current near to the load nominal current for the series-connected IGBTs during the SCF. These achievements result in a longer maximum permissible short-circuit time. These achievements are obtained by a control strategy that puts the series-connected IGBTs in a specific operating point in the active region during the SCF. Based on the proposed master–slave control strategy, one of the IGBTs is current controlled and rolls as the master. The other IGBTs are voltage controlled and imitate the master IGBT voltage. Consequently, a balanced voltage sharing is guaranteed for the series-connected IGBTs in the SCF. PSPICE simulations and experimental results are provided to verify the proper performance of the proposed HVFCL.