MZMostafa Zarghani

Mostafa Zarghani

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mostafa Zarghani has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Distributed Turn-Off Delay Compensator Scheme for Voltage Balancing of Series-Connected IGBTs

    by Mostafa Zarghani, Francesco Iannuzzo, Frede Blaabjerg, Shahriyar Kaboli

    This paper presents a voltage balancing scheme for Series-Connected IGBTs (SCIs) using a turn-off delay compensator. In SCIs, inherent synchronization challenges and parasitic capacitances lead to uneven voltage distribution and potential over-voltage conditions. Traditional time delay adjustment methods adjusting both turn-on and turn-off delays involve complex circuitry, difficult for numerous SCIs. The paper examines factors affecting voltage imbalances during turn-on and turn-off transitions, revealing that turn-off imbalances are more critical. Therefore, a straightforward approach is introduced for turn-off delay compensation, eliminating the need for high bandwidth and isolated feedbacks. Additionally, in the proposed scheme, by locally adjusting the turn-off delay time for each switch, obviating the necessity for separate command signals. Consequently, this pragmatic scheme is especially well-suited for applications where the complexity becomes a hindrance to expanding the number of series-connected switches. Simulation and experiments involving four IGBTs within a 2.4 kV system demonstrate a voltage balancing accuracy of less than 20 V.


  • Voltage Balancing of Series IGBTs in Short-Circuit Conditions

    by Mostafa Zarghani, Saeed Peyghami, Francesco Iannuzzo, Frede Blaabjerg, Shahriyar Kaboli

    This article proposes a scheme for balancing the voltage of series-connected insulated gate bipolar transistors (IGBTs), which is also very effective under short-circuit conditions. An optimized clamp-mode snubber is proposed, including an active-driver to balance the currents of the IGBTs during short-circuit, which in turn allows for a considerable reduction of the snubber capacitance. The approach is proven to be effective under short-circuit conditions by a maximum of 55 V voltage increment and a negligible difference in the current values. The effectiveness of the proposed approach is demonstrated through simulations in PSPICE software and experimental tests performed at 2 kV.


  • A Series Stacked IGBT Switch to Be Used as a Fault Current Limiter in HV High-Power Supplies

    by Sadegh Mohsenzade, Mostafa Zarghani, Shahriyar Kaboli

    The safe operating condition for the vacuum tubes is very important and critical since they are very expensive and delicate. Providing limited short circuit energy for the vacuum tube and fast transferring from the short circuit to the nominal operation state are absolutely necessary. Extant protection strategies threat the availability of the vacuum tubes. In addition, they cannot completely protect the tube due to the delay of the fault detection system. This paper proposes a high voltage (HV) short circuit fault current limiter which can limit the short circuit energy of the system inherently. The proposed structure activates automatically when the current exceeds the predetermined value. Hence, the need for the fault detection unit is minimized. The proposed short circuit fault current limiter is based on the series insulated gate bipolar transistors (IGBTs). Due to the interesting current limiting feature of the IGBTs, the short circuit current is limited for a definite time. During this time interval, the vacuum arc interrupts and the tube can operate instantaneously. In order to provide a safe operating condition of the series-connected IGBTs in the short circuit fault, several external circuits are suggested. The proper operation of the proposed short circuit fault current limiter is evaluated using simulations and experimental prototyping.


  • A Very Low-Ripple High-Voltage High-Power DC Power Supply Using an Interleaved Converter and a Linear Ripple Elimination Unit

    by Mostafa Zarghani, Sadegh Mohsenzade, Shahriyar Kaboli

    High voltage DC power supplies (HVDCPS) have been widely adopted for the vacuum tubes. In this application field, the low ripple voltage cannot be easily achieved by increasing the size of the output capacitance of the HVDCPS due to the limited permissible level of the stored energy. To obtain a low level of the output ripple as well as the limited value of the stored energy, the previously published literature proposed switching frequency increment. This approach has several shortcomings such as switching power loss increment, a limited level of the achievable ripple, and low value of the insulators lifetime. To improve the mentioned deficiencies, this paper hybridizes the series linear regulator and a high-frequency high-power DC interleaved converter. Using the proposed method, at the first stage, the level of the ripple decreases to a rational margin with increasing the ripple frequency. At the second stage, the level of the ripple reduces using the linear regulator to reach the expected precision. In order to validate the performance of the proposed structure, simulation and experimental results are provided for a 15 kV and 22.5 kW converter with the output voltage precision of 0.02%.


  • A Voltage Balancing Method for Series-Connected IGBTs Operating as a Fault Current Limiter in High-Voltage DC Power Supplies

    by Sadegh Mohsenzade, Mostafa Zarghani, Shahriyar Kaboli

    This article proposes a high-voltage fault current limiter (HVFCL) for high-voltage dc power supplies (HVdcPSs) which limits the current of the power supply automatically in the short-circuit fault (SCF). The proposed HVFCL is based on the series-connected insulated gate bipolar transistors (IGBTs). The main achievements of this article are the balanced voltage sharing and a very low value of the short-circuit current near to the load nominal current for the series-connected IGBTs during the SCF. These achievements result in a longer maximum permissible short-circuit time. These achievements are obtained by a control strategy that puts the series-connected IGBTs in a specific operating point in the active region during the SCF. Based on the proposed master–slave control strategy, one of the IGBTs is current controlled and rolls as the master. The other IGBTs are voltage controlled and imitate the master IGBT voltage. Consequently, a balanced voltage sharing is guaranteed for the series-connected IGBTs in the SCF. PSPICE simulations and experimental results are provided to verify the proper performance of the proposed HVFCL.


  • A High-Voltage Pulsed Power Supply With Online Rise Time Adjusting Capability for Vacuum Tubes

    by Mostafa Zarghani, Sadegh Mohsenzade, Shahriyar Kaboli

    Vacuum tubes such as gyrotrons and magnetrons require a specific range of high voltage pulse rise time for their proper operation. Otherwise, unavoidable operation modes or even arcs may take place in the vacuum tubes. Hence, the capability of the adjustable output pulse rise time is very promising for pulsed power supplies when they are dedicated to vacuum tubes. This paper proposes a high voltage series stacked insulated gate bipolar transistor (IGBT) switch with rise time adjusting capability to evolve the pulsed power supply abilities. The rise time adjustment is carried out using a low voltage ramped shape signal provided for all the IGBTs via a multi-winding transformer. In this way, the IGBTs are turned on as fast as possible with specific delays. The sequential turn on process of the IGBTs forms the output pulse rising edge. Unlike the extant strategies for controlling the turn on speed of the IGBTs, the dissipated power of the proposed method is negligible. The power associated with adjusting the output pulse rise time is recovered to the pulsed power supply using a simple and low voltage DC/DC converter. The proper performance of the proposed structure is evaluated using simulations and experimental prototyping.


  • An Extremely Low Ripple High Voltage Power Supply for Pulsed Current Applications

    by Mostafa Zarghani, Sadegh Mohsenzade, Amirabbas Hadizade, Shahriyar Kaboli

    This paper describes the development of an 18 kV, 30 kW power supply for a pulsed current load with the maximum current of 20 A and a di/dt equal to $100 \text{A}/\mu s$ . The achieved output ripple is less than 0.01%. In such a high level of precision, the most important issues are: 1) A considerable difference between the instantaneous and average output powers, as well as insufficient reaction speed of the converter to the fast load change. 2) Very low level of the voltage feedback and its sensitivity to the noise. The first issue necessitates a notable overdesign of the converter switches if the output voltage precision is dedicated to the converter. The second issue raises the problems relevant to observing the voltage ripple and providing it for the control loop. This paper proposes, a fast and high current linear regulator developed based on the load current feedforwarding. Using this approach, the fast regulator compensates the voltage change caused by a high level of instantaneous power. The main converter maintains the average power. Thus, there is not any need for the converter overdesigning. Furthermore, the problems relevant to the high voltage feedback and providing it for the control loop are removed. The voltage feedback is solely served to correct the current loop probable error. Hence the sensitivity of the control loop against the existing noise is minimized. Despite existing a 600nF capacitor as the output capacitor, the output voltage drop is less than 0.01 % in a wide range of the output current pulse up to $250 \mu s$ . The power supply is constructed and experimental results are provided to verify the mentioned specifications.


  • A Voltage Balancing Scheme for Series IGBTs to Increase Their Expected Lifetime in Pulsed Load Applications

    by Sadegh Mohsenzade, Mostafa Zarghani, Shahriyar Kaboli

    Clamp mode resistor capacitor diode (CMRCD) snubbers have a simple and easy implementing structure. They have been widely adopted in the pulsed power supplies to provide a safe operating condition for the series insulated gate bipolar transistors (IGBTs). The main problem of the CMRCD snubbers is their poor performance in the voltage balancing of the series IGBTs. They are essentially an overvoltage protection and clamp the voltage of the IGBTs in a probable potentially dangerous condition. This issue diminishes the expected lifetime of the series IGBTs where a number of them face a higher level of the voltage than that of the others. The unbalanced voltage of the series IGBTs will result in a lower value of the expected lifetime of the series IGBTs. To improve the expected lifetime of the series IGBTs a clamp mode RCD snubber with balanced voltage sharing for the series IGBTs is proposed. Adopting this proposal will lead to the balanced voltage sharing of the series IGBTs even in the blocking voltage below the nominal designed value. Consequently, the highest value of the lifetime is estimated for the series IGBTs in the stack. The simulation and experimental results truly demonstrate the effectiveness of the proposed structure.


  • A High-Voltage Series-Stacked IGBT Switch With Active Energy Recovery Feature for Pulsed Power Applications

    by Sadegh Mohsenzade, Mostafa Zarghani, Shahriyar Kaboli

    Applying series configuration of the insulated gate bipolar transistors (IGBTs) to the pulsed power supplies offers unique features such as compactness and long life time. In the high voltage pulsed power supplies, a large number of the IGBTs are required to be serially connected. Hence, the safe operating condition provision for the series IGBTs is an important and crucial issue. The effect of the voltage unbalancing factors becomes remarkable when the switches number in the series structure increases. There are passive and active methods to balance the voltage of the series IGBTs. In both of these methods, an amount of power must be dissipated to remove the effect of the voltage unbalancing factors. Consequently, the power loss is considerable when a large number of series devices are necessary. This paper proposes an effective power recovery system that recovers the power associated with the series stacking of the IGBTs. Using this proposal, the efficiency of the resulted series switch enhances considerably. The power recovery system can be implemented easily for any number of series IGBTs. It consists of a simple DC/DC converter and several interconnection diodes for power recovery procedure. Proper performance of the proposed structure is evaluated by the aid of simulations and experiments.


  • A Series Stacked IGBT Switch Based on a Concentrated Clamp Mode Snubber for Pulsed Power Applications

    by Mostafa Zarghani, Sadegh Mohsenzade, Shahriyar Kaboli

    Clamp mode snubbers are very well suited for the series structure of the insulated-gate bipolar transistors (IGBTs) in pulsed power applications. They properly meet the necessities expected from them such as the fast operating of the series IGBTs since they have no effect on the gate side. In addition, they can provide safe voltage condition for the IGBTs in short circuit faults, which are very probable in pulsed applications. The clamp mode snubber can perform its voltage balancing task whenever the power capacity of the snubber can support the injected powers due to the voltage unbalancing factors. This paper initially introduces the main factors injecting power to the snubbers. Then, it will be illustrated that the exact injected power to each predetermined snubber cannot be determined due to uncertainties about the effect of the voltage unbalancing factors. Although it is impossible to determine the exact value of the power injected to each snubber, the total injected powers to the snubbers can be calculated. Therefore, as an effective remedy, the paper proposes a concentrated snubber. Using the proposal, all the injected powers are conducted to a centralized circuit and can be easily managed. In addition, analytical expressions are provided for proper dimensioning of the proposed concentrated snubber elements. Furthermore, the performance of the proposed concentrated snubber is evaluated using simulations and experimental prototyping.