Debbie De Jager
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Debbie De Jager has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Marshall Sheerene Sheldon
Department of Chemical Engineering, Cape Peninsula University of Technology, P.O. Box 652, Cape Town 8000, South Africa
6 shared publications W. Edwards
4 shared publications- Estella Zandile Jingxi
Department of Chemical Engineering, Cape Peninsula University of Technology, P.O. Box 1906, Bellville 7535, South Africa
2 shared publications Irena Petrinic
Department of Chemical Engineering, Cape Peninsula University of Technology, P.O. Box 1906, Bellville 7535, South Africa; Faculty of Chemistry and Chemical Engineering, University of Maribor, Smetanova ulica 17, SI-2000 Maribor, Slovenia
2 shared publicationsMahomet Njoya
2 shared publicationsRobyn Augustine
Department of Chemical Engineering, Cape Peninsula University of Technology, P.O. Box 1906, Bellville 7535, South Africa
2 shared publications
Latest Publications
- Open Access
- 1 June 2026
- Published by KEAI Publishing in Petroleum Research
- Vol. 11 (2) , 633-640
Physicochemical characterization of oilfield produced water and its treatment constraints
- 1 June 2026
- Published by KEAI Publishing in Petroleum Research
- Vol. 11 (2) , 633-640
Open AccessPhysicochemical characterization of oilfield produced water and its treatment constraints
- Open Access
- 1 June 2025
- Published by KEAI Publishing in Petroleum Research
- Vol. 10 (2) , 342-351
The role of hydrocyclone and induced gas flotation technologies in offshore produced water deoiling advancements
Produced water, a byproduct of oil and gas extraction, presents significant environmental challenges if not properly treated. This review focuses on advancements in two primary offshore deoiling technologies, namely: induced gas flotation and hydrocyclones, tracing their evolution from the 1940s to the present. The study provides a detailed comparison of these technologies in terms of efficiency, energy consumption, and waste generation, offering both qualitative and quantitative assessments. Particular attention is given to the integration of hydrocyclone-induced gas flotation (HIGF) systems, which enhance oil removal efficiency while reducing energy consumption, making them an important solution in offshore produced water management. Additionally, the review identifies specific design improvements in flotation units, such as multistage configurations, and explores the role of operational control in optimizing hydrocyclone performance. Global variations in produced water discharge standards are examined, emphasizing the need for stricter environmental regulations. In addition, this study highlights the combined use of hydrocyclone and flotation technologies as a comprehensive approach for addressing both environmental and operational challenges in offshore produced water treatment.
- 1 June 2025
- Published by KEAI Publishing in Petroleum Research
- Vol. 10 (2) , 342-351
Open AccessThe role of hydrocyclone and induced gas flotation technologies in offshore produced water deoiling advancements
Produced water, a byproduct of oil and gas extraction, presents significant environmental challenges if not properly treated. This review focuses on advancements in two primary offshore deoiling technologies, namely: induced gas flotation and hydrocyclones, tracing their evolution from the 1940s to the present. The study provides a detailed comparison of these technologies in terms of efficiency, energy consumption, and waste generation, offering both qualitative and quantitative assessments. Particular attention is given to the integration of hydrocyclone-induced gas flotation (HIGF) systems, which enhance oil removal efficiency while reducing energy consumption, making them an important solution in offshore produced water management. Additionally, the review identifies specific design improvements in flotation units, such as multistage configurations, and explores the role of operational control in optimizing hydrocyclone performance. Global variations in produced water discharge standards are examined, emphasizing the need for stricter environmental regulations. In addition, this study highlights the combined use of hydrocyclone and flotation technologies as a comprehensive approach for addressing both environmental and operational challenges in offshore produced water treatment.
- Open Access
- 15 September 2019
- Published by IWA Publishing in Water Science & Technology
- Vol. 80 (6) , 1053-1062
Forward osmosis: dyeing draw solutions for water reclamation from feed water resources
Reactive Black 5 and Basic Blue 41 GRL dyeing solutions (dye-to-salt mixture in a 1:10 dye-to-salt mass ratio) were investigated as draw solutions (DS) in a forward osmosis (FO) system with a biomimetic membrane. Synthetic seawater (SSW) and textile wastewater (TWW1 and TWW2) were evaluated as feed solutions (FS) for water reclamation. Reactive Black 5 and Basic Blue 41 GRL were diluted from 0.02 M to concentrations of 0.002 and 0.004 M, respectively. With Reactive Black 5 as DS and SSW as FS, an initial flux of 20.24 L/m2 h and water recovery of 75% was achieved. Using TWW1 and TWW2 initial water fluxes of 19.51 and 13.43 L/m2 h were achieved, respectively, with a 30% water recovery. Using Basic Blue 41 GRL initial water fluxes of 18.72, 15.13 and 13.42 L/m2 h were achieved with SSW, TWW1, and TWW2 as FS with water recoveries of 50, 20 and 20%, respectively. The average reverse solute fluxes for Reactive Black 5 and Basic Blue 41 GRL were 0.06 to 0.34 g/m2 h, respectively. Diluted dyeing solutions were produced, with simultaneous water reclamation from SSW and TWW resulting in similar or higher water fluxes and lower reverse solute fluxes compared to other commercially available membranes.
- 15 September 2019
- Published by IWA Publishing in Water Science & Technology
- Vol. 80 (6) , 1053-1062
Open AccessForward osmosis: dyeing draw solutions for water reclamation from feed water resources
Reactive Black 5 and Basic Blue 41 GRL dyeing solutions (dye-to-salt mixture in a 1:10 dye-to-salt mass ratio) were investigated as draw solutions (DS) in a forward osmosis (FO) system with a biomimetic membrane. Synthetic seawater (SSW) and textile wastewater (TWW1 and TWW2) were evaluated as feed solutions (FS) for water reclamation. Reactive Black 5 and Basic Blue 41 GRL were diluted from 0.02 M to concentrations of 0.002 and 0.004 M, respectively. With Reactive Black 5 as DS and SSW as FS, an initial flux of 20.24 L/m2 h and water recovery of 75% was achieved. Using TWW1 and TWW2 initial water fluxes of 19.51 and 13.43 L/m2 h were achieved, respectively, with a 30% water recovery. Using Basic Blue 41 GRL initial water fluxes of 18.72, 15.13 and 13.42 L/m2 h were achieved with SSW, TWW1, and TWW2 as FS with water recoveries of 50, 20 and 20%, respectively. The average reverse solute fluxes for Reactive Black 5 and Basic Blue 41 GRL were 0.06 to 0.34 g/m2 h, respectively. Diluted dyeing solutions were produced, with simultaneous water reclamation from SSW and TWW resulting in similar or higher water fluxes and lower reverse solute fluxes compared to other commercially available membranes.
- Open Access
- 25 April 2018
- Published by Academy of Science of South Africa in Water SA
- Vol. 44 (2 April) , 258-268-268
Potential of dyes as draw solutions in forward osmosis for the South African textile industry
The textile industry produces large volumes of wastewater that requires appropriate treatment before being released into the environment. Research globally has focused on advanced desalination technologies to augment the limited freshwater resources. Forward osmosis (FO) technology has gained substantial interest as a possible lower-energy desalination technology. However, challenges such as the availability of effective draw solutions (DS) have limited its implementation. This study evaluated alternative feed water resources and assessed the potential of dye solutions as DS. The aim is to dilute a concentrated dye DS to a target concentration for direct dye-batch use, thereby reclaiming water resources. The measured osmotic pressure (OP) of the alternative feed solutions (synthetic brackish water; syntethic seawater; seawater from the Atlantic and Indian Oceans; and wastewater from two textile factories) were 414, 2 761, 2 580, 2 614; 1 716 and 7 822 kPa, respectively. Three basic dyes (Maxilon Turquoise, Red and Blue) and three reactive dyes (Carmine, Olive Green and Black) were selected based on common use in the South African textile industry. The dye samples were prepared without and with salt at different concentrations and different dye-to-salt mass ratios ranging from 1:10 to 1:60. The OP trends for the basic dyes followed Blue >> Red > Turquoise and for the reactive dyes Black >> Olive > Carmine. The overall OP trend was Black > Olive > Carmine > Blue > Red > Turquoise. The OP at different dye concentrations and different dye-to-salt ratios was mostly influenced by the dye chemistry and molecular weight (Mw) rather than the type of dye, i.e., reactive vs basic.The OP trend for the dye-to-salt ratios was 1:60 > 1:50 > 1:40 > 1:30 > 1:20 > 1:10. For both the basic and reactive dyes a linear relationship exists between OP and dye concentration; as well as between OP and Mw. The dye DS exhibited larger OP compared to that of the FS evaluated, thus rendering them suitable DS. Keywords: draw solution; dyes; feed solution; forward osmosis; osmotic pressure; textile industry; textile wastewater
- 25 April 2018
- Published by Academy of Science of South Africa in Water SA
- Vol. 44 (2 April) , 258-268-268
Open AccessPotential of dyes as draw solutions in forward osmosis for the South African textile industry
The textile industry produces large volumes of wastewater that requires appropriate treatment before being released into the environment. Research globally has focused on advanced desalination technologies to augment the limited freshwater resources. Forward osmosis (FO) technology has gained substantial interest as a possible lower-energy desalination technology. However, challenges such as the availability of effective draw solutions (DS) have limited its implementation. This study evaluated alternative feed water resources and assessed the potential of dye solutions as DS. The aim is to dilute a concentrated dye DS to a target concentration for direct dye-batch use, thereby reclaiming water resources. The measured osmotic pressure (OP) of the alternative feed solutions (synthetic brackish water; syntethic seawater; seawater from the Atlantic and Indian Oceans; and wastewater from two textile factories) were 414, 2 761, 2 580, 2 614; 1 716 and 7 822 kPa, respectively. Three basic dyes (Maxilon Turquoise, Red and Blue) and three reactive dyes (Carmine, Olive Green and Black) were selected based on common use in the South African textile industry. The dye samples were prepared without and with salt at different concentrations and different dye-to-salt mass ratios ranging from 1:10 to 1:60. The OP trends for the basic dyes followed Blue >> Red > Turquoise and for the reactive dyes Black >> Olive > Carmine. The overall OP trend was Black > Olive > Carmine > Blue > Red > Turquoise. The OP at different dye concentrations and different dye-to-salt ratios was mostly influenced by the dye chemistry and molecular weight (Mw) rather than the type of dye, i.e., reactive vs basic.The OP trend for the dye-to-salt ratios was 1:60 > 1:50 > 1:40 > 1:30 > 1:20 > 1:10. For both the basic and reactive dyes a linear relationship exists between OP and dye concentration; as well as between OP and Mw. The dye DS exhibited larger OP compared to that of the FS evaluated, thus rendering them suitable DS. Keywords: draw solution; dyes; feed solution; forward osmosis; osmotic pressure; textile industry; textile wastewater
- Open Access
- 1 March 2016
- Published by IWA Publishing in Water Practice & Technology
- Vol. 11 (1) , 86-92
Performance of an expanded granular sludge bed (EGSB) reactor coupled with anoxic and aerobic bioreactors for treating poultry slaughterhouse wastewater
Generally, slaughterhouses have the largest consumption of fresh water and thus generate large quantities of high strength wastewater, which can be treated successfully using low cost biological treatment processes. In this study, the feasibility of using an expanded granular sludge bed (EGSB) anaerobic reactor coupled with anoxic and aerobic bioreactors for the treatment of poultry slaughterhouse wastewater was investigated. The poultry slaughterhouse was characterized by high chemical oxygen demand (COD), 2 to 6 g/L, with average biological oxygen demand of 2.4 g/L and average fats, oil and grease (FOG) being 0.55 g/L. A continuous EGSB anaerobic reactor was operated for 26 days at different hydraulic retention times (HRT), i.e. 7, 4, 3 days, and organic loading rates (OLR) of 0.5, 0.7 and 1.0 g COD/L.day, respectively, to assess the bioremediation of the poultry slaughterhouse wastewater. The average COD removal from the EGSB was 40%, 57% and 55% at the different OLR and HRT assessed. At high OLR of 1.0 g COD/L.day, the overall COD removal from the system (EGSB-anoxic/aerobic) averaged 65%. The system experienced periodical sludge washout during high FOG and suspended solids loading. It was concluded that the EGSB system requires a dissolved air flotation system, for FOG/suspended solid reduction, as the performance of the overall system was observed to deteriorate over time due to the presence of a high quantity of FOG including suspended solids.
- 1 March 2016
- Published by IWA Publishing in Water Practice & Technology
- Vol. 11 (1) , 86-92
Open AccessPerformance of an expanded granular sludge bed (EGSB) reactor coupled with anoxic and aerobic bioreactors for treating poultry slaughterhouse wastewater
Generally, slaughterhouses have the largest consumption of fresh water and thus generate large quantities of high strength wastewater, which can be treated successfully using low cost biological treatment processes. In this study, the feasibility of using an expanded granular sludge bed (EGSB) anaerobic reactor coupled with anoxic and aerobic bioreactors for the treatment of poultry slaughterhouse wastewater was investigated. The poultry slaughterhouse was characterized by high chemical oxygen demand (COD), 2 to 6 g/L, with average biological oxygen demand of 2.4 g/L and average fats, oil and grease (FOG) being 0.55 g/L. A continuous EGSB anaerobic reactor was operated for 26 days at different hydraulic retention times (HRT), i.e. 7, 4, 3 days, and organic loading rates (OLR) of 0.5, 0.7 and 1.0 g COD/L.day, respectively, to assess the bioremediation of the poultry slaughterhouse wastewater. The average COD removal from the EGSB was 40%, 57% and 55% at the different OLR and HRT assessed. At high OLR of 1.0 g COD/L.day, the overall COD removal from the system (EGSB-anoxic/aerobic) averaged 65%. The system experienced periodical sludge washout during high FOG and suspended solids loading. It was concluded that the EGSB system requires a dissolved air flotation system, for FOG/suspended solid reduction, as the performance of the overall system was observed to deteriorate over time due to the presence of a high quantity of FOG including suspended solids.
- 1 October 2014
- Published by Elsevier in Separation and Purification Technology
- Vol. 135, 135-144
Colour removal from textile wastewater using a pilot-scale dual-stage MBR and subsequent RO system
- 1 October 2014
- Published by Elsevier in Separation and Purification Technology
- Vol. 135, 135-144
Colour removal from textile wastewater using a pilot-scale dual-stage MBR and subsequent RO system
- Open Access
- 1 March 2012
- Published by IWA Publishing in Water Science & Technology
- Vol. 65 (5) , 907-914
Membrane bioreactor application within the treatment of high-strength textile effluent
A pilot-scale dual-stage membrane bioreactor (dsMBR) incorporating two ultra-filtration (UF) side-stream membrane modules was designed, constructed, operated and evaluated on-site for treating high-strength textile effluent. The effluent stream was characterised by a COD range of between 45 to 2,820 mg/L and an average BOD of 192.5 mg/L. The dsMBR achieved an average COD reduction of 75% with a maximum of 97% over the 9 month test period. The COD concentration obtained after dsMBR treatment averaged at 190 mg/L, which was well within the discharge standard. The average reduction in turbidity and TSS were 94% and 19.6%, respectively, during the UF-MBR stage of the system. Subsequent treatment of the UF-permeate with nanofiltration (NF) and reverse osmosis (RO) removed both the residual colour and remaining salt. A consistent reduction in the color of the incoming effluent was evident. The ADMI was reduced from an average of 659 to ∼20, a lower ADMI and colour compared to the potable water. An average conductivity rejection of 91% was achieved with conductivity being reduced from an average of 7,700 to 693 μS/cm and the TDS reduced from an average of 5,700 to 473 mg/L, which facilitated an average TDS rejection of 92%.
- 1 March 2012
- Published by IWA Publishing in Water Science & Technology
- Vol. 65 (5) , 907-914
Open AccessMembrane bioreactor application within the treatment of high-strength textile effluent
A pilot-scale dual-stage membrane bioreactor (dsMBR) incorporating two ultra-filtration (UF) side-stream membrane modules was designed, constructed, operated and evaluated on-site for treating high-strength textile effluent. The effluent stream was characterised by a COD range of between 45 to 2,820 mg/L and an average BOD of 192.5 mg/L. The dsMBR achieved an average COD reduction of 75% with a maximum of 97% over the 9 month test period. The COD concentration obtained after dsMBR treatment averaged at 190 mg/L, which was well within the discharge standard. The average reduction in turbidity and TSS were 94% and 19.6%, respectively, during the UF-MBR stage of the system. Subsequent treatment of the UF-permeate with nanofiltration (NF) and reverse osmosis (RO) removed both the residual colour and remaining salt. A consistent reduction in the color of the incoming effluent was evident. The ADMI was reduced from an average of 659 to ∼20, a lower ADMI and colour compared to the potable water. An average conductivity rejection of 91% was achieved with conductivity being reduced from an average of 7,700 to 693 μS/cm and the TDS reduced from an average of 5,700 to 473 mg/L, which facilitated an average TDS rejection of 92%.
- 31 December 2009
- Published by Elsevier in Enzyme and Microbial Technology
- Vol. 45 (6-7) , 449-456
Modelling growth kinetics of Streptomyces coelicolor A3(2) in a pressurised membrane gradostat reactor (MGR)
- 31 December 2009
- Published by Elsevier in Enzyme and Microbial Technology
- Vol. 45 (6-7) , 449-456
Modelling growth kinetics of Streptomyces coelicolor A3(2) in a pressurised membrane gradostat reactor (MGR)
- 1 May 2009
- Published by Elsevier in Journal of Membrane Science
- Vol. 333 (1-2) , 79-87
The effect of Streptomyces coelicolor development on the hydrodynamics of a vertically orientated capillary membrane gradostat reactor
- 1 May 2009
- Published by Elsevier in Journal of Membrane Science
- Vol. 333 (1-2) , 79-87
The effect of Streptomyces coelicolor development on the hydrodynamics of a vertically orientated capillary membrane gradostat reactor