Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Babak Afzali has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Speed-Variant Balancing Method for Flexible Rotary Machines Based on Acoustic Responses

    by Andrew Peplow, Javad Isavand, Afshar Kasaei, Babak Afzali, Delphine Bard-Hagberg

    As rotary machines have become more complicated, balancing processes have been classified as a vital step in condition monitoring to ensure that machines operate reliably, smoothly and safely. All rotating objects will deflect during rotation and all objects possess certain natural frequencies in the absence of rotation. However, an unbalanced object can cause significant unwanted deflection created by resonant vibration at a frequency (cycles/second) close to certain rotational speeds (rotations/second), known as critical speeds. This is especially important for flexible machines which normally work at rotations above their critical speeds. Imbalance is a common problem in flexible rotating machinery that can lead to extreme vibration and noise levels. This is one of the major reasons for studying various balancing methods applied to the vibration response of rotating machines. Recently, the relation between acoustic and vibration response during a rotary machine balancing process based on the original Four-Run method has been presented for constant speed machines. This method cannot be applied to machines in start-up or shut-off. Hence, by considering the acoustic and vibration responses of a machine between its critical speeds, this research presents a new innovative speed-variant balancing method based on the original Four-Run method, named as (PPCS) Peak to Peak for Critical Speeds. The proposed method consists of two major types of application: the first is in the run-up of the machine and the second is in shut down. Experimental laboratory results show that this method can be implemented for speed-variant and flexible rotary machines during run-up or shut-down transient processes based on acoustic and vibration measurements. Further, the results show the same trend in acoustic and vibration responses during balancing process which was shown for constant speed rotary machines. With a 40% improvement in response compared to around 55% obtained by traditional vibration measurements, the results found show an appreciable benefit in an alternative acoustic methodology that may have not been considered previously for run-up and shut-down issues. In addition, since only the magnitude of response is required and this is a non-contact technique an acoustic-only methodology, it can be employed with some confidence as an innovative and readily available method for condition monitoring.


  • Open Access

    A Speed-Variant Balancing Method for Flexible Rotary Machines Based on Acoustic Responses

    by Andrew Peplow, Javad Isavand, Afshar Kasaei, Babak Afzali, Delphine Bard-Hagberg

    As rotary machines have become more complicated, balancing processes have been classified as a vital step in condition monitoring to ensure machines operate both reliably and safely. This is especially important for flexible machines which normally work at rotations speeds above critical limits. Imbalance is a common problem in flexible rotating machinery that can lead to extreme vibration and noise levels. This is one of the major reasons for studying various balancing methods applied to the vibration response of rotating machines. Recently, the relation between acoustic and vibration response during a rotary machine balancing process based on the Four-Run method has been presented for constant speed machines. This method cannot be applied to machines in start-up or shut-off. Hence, by considering the acoustic and vibration responses of a machine between its critical speeds, this research presents a new innovative speed-variant balancing method based on the original Four-Run method, named as "Peak to Peak for Critical Speeds (PPCS)". The proposed method consists of two major types of application: the first is in the Run-up of the machine and the second is in Shut-down. Experimental laboratory results show that the PPCS method can be implemented for speed-variant and flexible rotary machines during run-up or shut-down transient processes based on acoustic and vibration measurements. As a phase-less and a contactless method, the PPCS can be employed as an innovative and readily available method for condition monitoring in the future.

  • Comparison of vibration and acoustic responses in a rotary machine balancing process

    by Javad Isavand, Afshar Kasaei, Andrew Peplow, Babak Afzali, Ebrahim Shirzadi


  • Numerical investigation on thermo-acoustic effects and flow characteristics in semi-conical Hartmann–Sprenger resonance tube

    by Babak Afzali, Hassan Karimi

    Hartmann–Sprenger tube is a device in which an underexpanded jet enters a closed end tube that is placed in a specific distance from the nozzle. In specific conditions, a standing shock is built in front of the tube, which oscillates based on the tube resonance frequency and creates oscillatory flows with periodic shock motions along the tube. In these conditions, intensive temperature rise could be observed near the tube end wall. Considering these thermal effects, the device could be used as a combustion starter in the space propulsion systems. The present study focuses on flow analysis in various phases of the oscillatory process in a semi-conical PTFE resonance tube by the aim of numerical simulation results. An experimental test is also performed for validation purposes. The T–S diagram is plotted to describe the thermal effects in detail during the oscillatory processes. Various modes of shock contact with flow front are described. In order to follow up the shock traveling process, the diagrams of changes related to major flow properties inside the tube are used. Generation of small turbulences at the moments of combination of compression waves and beginning of flow entrance is also detected. According to the results, traveling of shock waves through the trapped gas was found to be the major mechanism for heat generation inside the tube. The thermal effects are also compared in the conical and cylindrical tubes. The flow analysis will lead to increase in insight for shock motion and heat generation mechanism in a semi-conical Hartmann–Sprenger tube.


  • Dynamic Simulation of Gas Turbine Fuel Gas Supply System During Transient Operations

    by Babak Afzali, Hassan Karimi, Ehsan Tahmasebi

    The primary purpose of this paper is to simulate the fuel gas supply system of a gas turbine unit. This simulation allows determination of supply gas flow properties such as flow rate and pressure as a function of time. The concentration is on transient processes of heavy duty gas turbine such as startup, shutdown, emergency stop and load following. In the past, it was common to use a quasi steady assumption allowed the simulation of the gas turbine system. In this work, a one dimensional dynamic model of the gas flow in a fixed area pipe with friction is developed. This development is based on McCormack finite difference method in straight pipes combined with the method of characteristic at branches. The McCormack technique is based on prediction-correction of steps. Such a procedure will allow one to take into account the time delays and response time of various devices associated with the transient processes of the gas turbine system. The most important device in the pipeline system of a gas turbine is the control valve that adjusts the fuel gas flow by precise control of its traveling piston. This particular element is modeled and simulated similar to a standard nozzle entrance section. Such a modeling scheme considers a chocked flow through the control valve. The considered hydraulic circuit is comprised of a combination of simple gas pipes, valves, and pressure loss components (e.g., junctions, bends, fittings, and injection nozzles). By specifying the boundary conditions and the control valve piston position, a method is developed that allows simulation of such hydraulic circuits. In continuation, the above mentioned hydraulic circuit is considered as a fuel gas supply system for a heavy duty gas turbine operating in a power plant. The circuit is simulated, and such disturbances during start, shutdown, piston travel of the control valve, and break in power generation are taken into account. Finally, fuel flow properties during mentioned processes would be obtained as a function of time and an analysis of the simulation results is performed.