Roberto Torelli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Roberto Torelli has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Hengjie Guo
Tsinghua University
6 shared publications Yuanjiang Pei
5 shared publicationsSibendu Som
Transportation and Power Systems Division, Argonne National Laboratory, Lemont, USA
4 shared publications- David Markt
Univ Massachusetts Dartmouth, Dept Mech Engn, Dartmouth, MA 02747 USA
3 shared publications - Michael Traver
Aramco Americas, USA
3 shared publications Seong-Young Lee
Department of Mechanical Engineering-Engineering Mechanics, Michigan Technological University, Houghton, Michigan 49931, USA
3 shared publications
Latest Publications
- 17 June 2025
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 26 (11) , 1703-1725
Optimization of spray breakup model parameters for predicting fuel spray and film characteristics in gasoline direct injection engines
This study investigated the behavior of gasoline direct injection (GDI) sprays using computational fluid dynamics (CFD). The authors developed an approach to identify optimal spray breakup model parameters by evaluating an error function across numerous simulations, with the goal of minimizing discrepancies from experimental data. Using the optimal setup, the simulated spray matched well with projected liquid volume distributions, liquid penetration, and spray width measured in a constant-pressure continuous-flow chamber. To further validate the approach, the same setup was tested across various fuels, injectors, and operating conditions. Subsequently, the optimal setup, along with a recently developed spray-wall interaction model, were applied to a direct-injection spark-ignited engine under late-injection conditions to predict and evaluate fuel film formation and evolution at varying engine coolant temperatures. With the centrally mounted injector directing the spray toward the piston, simulations indicated that the spray tends to impinge on the piston surface. The proposed simulation framework also accurately captured the aggregate film area on the piston surface, aligning with previously published experimental results. Moreover, simulations showed that increasing the coolant temperature from cold start conditions (333 K) to warm conditions (363 K) reduced the fuel mass deposited on the piston by roughly 50%. Furthermore, for the spray-guided engine configuration studied in this work, the CFD model predicted minimal film deposition on the spark plug electrodes regardless of the coolant temperatures due to a relatively weak in-cylinder flow during the compression phase.
- 17 June 2025
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 26 (11) , 1703-1725
Optimization of spray breakup model parameters for predicting fuel spray and film characteristics in gasoline direct injection engines
This study investigated the behavior of gasoline direct injection (GDI) sprays using computational fluid dynamics (CFD). The authors developed an approach to identify optimal spray breakup model parameters by evaluating an error function across numerous simulations, with the goal of minimizing discrepancies from experimental data. Using the optimal setup, the simulated spray matched well with projected liquid volume distributions, liquid penetration, and spray width measured in a constant-pressure continuous-flow chamber. To further validate the approach, the same setup was tested across various fuels, injectors, and operating conditions. Subsequently, the optimal setup, along with a recently developed spray-wall interaction model, were applied to a direct-injection spark-ignited engine under late-injection conditions to predict and evaluate fuel film formation and evolution at varying engine coolant temperatures. With the centrally mounted injector directing the spray toward the piston, simulations indicated that the spray tends to impinge on the piston surface. The proposed simulation framework also accurately captured the aggregate film area on the piston surface, aligning with previously published experimental results. Moreover, simulations showed that increasing the coolant temperature from cold start conditions (333 K) to warm conditions (363 K) reduced the fuel mass deposited on the piston by roughly 50%. Furthermore, for the spray-guided engine configuration studied in this work, the CFD model predicted minimal film deposition on the spark plug electrodes regardless of the coolant temperatures due to a relatively weak in-cylinder flow during the compression phase.
- 12 December 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 98, 751-771
Multicycle large-eddy simulations of a direct-injection hydrogen-fueled optical engine
- 12 December 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 98, 751-771
Multicycle large-eddy simulations of a direct-injection hydrogen-fueled optical engine
- 11 March 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (9) , 1-35
A Phenomenological Thermal Spray Wall Interaction Modeling Framework Applied to a High-Temperature Ignition Assistant Device
Airborne compression ignition engines must operate with reliable ignition systems to achieve proper ignition at every cycle, particularly at high altitudes. Glow-plug-based ignition-assistant (IA) devices can provide the necessary energy to preheat the fuel and ensure ignitability of the fuel-air mixture. Ignitability of liquid sprays can be facilitated via direct impingement onto the hot IA surface, however this comes with adverse effects on the IA durability. Therefore, optimizing an IA's design requires detailed understanding of the physics of fuel spray impingement of superheated surfaces. While spray impingement on relatively low wall temperatures has been extensively studied and appropriate numerical models have been proposed through the years, fundamental understanding of high-speed liquid spray impingement on superheated walls is still elusive. This work aims to formulate a phenomenological thermal spray-wall interaction framework for modeling the film-boiling-induced heat transfer, atomization, and dispersion of fuel spray droplets impinging onto a superheated IA device. A qualitative comparison of the new phenomenological model is performed against optical experiments from the literature of an F-24 fuel spray injected onto an IA device located 12 mm away from the injector tip. The temperature of the IA was set at 1400 K. The fuel injection pressure was 400 bar, while the ambient gas pressure and temperature were 30 bar and 800 K, respectively. The performance of the phenomenological model is evaluated in comparison with two other state-of-art models from the literature. A qualitative analysis of the different spray and fuel-air mixture characteristics is performed to outline the differences in the predictions offered by the new phenomenological model and the two state-of-art spray-wall interaction models.
- 11 March 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (9) , 1-35
A Phenomenological Thermal Spray Wall Interaction Modeling Framework Applied to a High-Temperature Ignition Assistant Device
Airborne compression ignition engines must operate with reliable ignition systems to achieve proper ignition at every cycle, particularly at high altitudes. Glow-plug-based ignition-assistant (IA) devices can provide the necessary energy to preheat the fuel and ensure ignitability of the fuel-air mixture. Ignitability of liquid sprays can be facilitated via direct impingement onto the hot IA surface, however this comes with adverse effects on the IA durability. Therefore, optimizing an IA's design requires detailed understanding of the physics of fuel spray impingement of superheated surfaces. While spray impingement on relatively low wall temperatures has been extensively studied and appropriate numerical models have been proposed through the years, fundamental understanding of high-speed liquid spray impingement on superheated walls is still elusive. This work aims to formulate a phenomenological thermal spray-wall interaction framework for modeling the film-boiling-induced heat transfer, atomization, and dispersion of fuel spray droplets impinging onto a superheated IA device. A qualitative comparison of the new phenomenological model is performed against optical experiments from the literature of an F-24 fuel spray injected onto an IA device located 12 mm away from the injector tip. The temperature of the IA was set at 1400 K. The fuel injection pressure was 400 bar, while the ambient gas pressure and temperature were 30 bar and 800 K, respectively. The performance of the phenomenological model is evaluated in comparison with two other state-of-art models from the literature. A qualitative analysis of the different spray and fuel-air mixture characteristics is performed to outline the differences in the predictions offered by the new phenomenological model and the two state-of-art spray-wall interaction models.
- 22 February 2024
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 25 (7) , 1265-1280
In-cylinder spray evolution in a motored central-injection gasoline engine: Imaging and simulating the effects of flash-boiling and intake crossflow
Accurate predictions of fuel spray behavior and mixture formation in simulations of direct-injection spark-ignition (DISI) engines are fundamental to ensure proper description of all subsequent processes including ignition, combustion, and emissions. In this work, the spray evolution in a single-cylinder optical DISI engine was studied experimentally and numerically with the goal of enabling predictive computational fluid dynamics (CFD) modeling of in-cylinder sprays. The authors explored a wide range of operating conditions characterized by several fuel injection temperatures and engine speeds, using a well-characterized nine-component gasoline surrogate known as PACE-20. The effect of flash boiling and intake crossflow on the spray is discussed, with a focus on evaluating the ability of the spray models to capture highly transient spray behavior. In the experiments, the fuel temperature was varied between 20°C and 80°C, allowing for non-flash- to flash-boiling transition to emerge with enhanced flashing intensity at the highest temperatures. Spray collapse resulted in vapor-rich regions, owing to the locally lower inertia of the fluid. Varying the engine speed from 650 to 1950 rpm promoted increasingly more turbulent in-cylinder crossflow which interacted with the spray during the injection event and resulted in enhanced spray dispersion. The CFD model was able to capture the spray morphology transition at different fuel temperatures and engine speeds adequately. It is shown that the spray breakup model could capture the transitional spray behavior induced by flash boiling atomization and intake flow via proper initialization of the spray cone angle and calibration of the spray models’ constants.
- 22 February 2024
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 25 (7) , 1265-1280
In-cylinder spray evolution in a motored central-injection gasoline engine: Imaging and simulating the effects of flash-boiling and intake crossflow
Accurate predictions of fuel spray behavior and mixture formation in simulations of direct-injection spark-ignition (DISI) engines are fundamental to ensure proper description of all subsequent processes including ignition, combustion, and emissions. In this work, the spray evolution in a single-cylinder optical DISI engine was studied experimentally and numerically with the goal of enabling predictive computational fluid dynamics (CFD) modeling of in-cylinder sprays. The authors explored a wide range of operating conditions characterized by several fuel injection temperatures and engine speeds, using a well-characterized nine-component gasoline surrogate known as PACE-20. The effect of flash boiling and intake crossflow on the spray is discussed, with a focus on evaluating the ability of the spray models to capture highly transient spray behavior. In the experiments, the fuel temperature was varied between 20°C and 80°C, allowing for non-flash- to flash-boiling transition to emerge with enhanced flashing intensity at the highest temperatures. Spray collapse resulted in vapor-rich regions, owing to the locally lower inertia of the fluid. Varying the engine speed from 650 to 1950 rpm promoted increasingly more turbulent in-cylinder crossflow which interacted with the spray during the injection event and resulted in enhanced spray dispersion. The CFD model was able to capture the spray morphology transition at different fuel temperatures and engine speeds adequately. It is shown that the spray breakup model could capture the transitional spray behavior induced by flash boiling atomization and intake flow via proper initialization of the spray cone angle and calibration of the spray models’ constants.
- Open Access
- 1 October 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (10)
Modeling of the spray-induced wall stress acting on the ignition assistance device
This research introduces a novel wall-stress model called the Spray-Induced Wall Stress (SIWS) model, which considers the effects of spray-wall impingement and the resulting formation of wall stress within the Lagrangian spray modeling framework. The primary objective of this paper is to provide a mathematical description of the fundamental physics underlying the model. Subsequently, the proposed model is validated using existing experimental data. The remainder of the study focuses on the practical application of the model to an ignition assistance device. Specifically, this device is installed in a compression ignition engine and designed to enhance ignition in aviation-fueled high-altitude aircraft propulsion systems. The research sheds light on the mechanical impulse caused by the high-speed impact of the spray jet, leading to the accumulation of mechanical stress on the rigid body of the ignition assistance device. Previous studies on fluid–structure interaction have only considered the interaction between the gas phase and the solid wall. However, the SIWS model incorporates the additional impact of the impinging liquid spray jet. Consequently, the simulated stress distribution on the ignition assistance device can be estimated by considering both the gas-phase-induced term and the spray-induced term simultaneously.
- 1 October 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (10)
Open AccessModeling of the spray-induced wall stress acting on the ignition assistance device
This research introduces a novel wall-stress model called the Spray-Induced Wall Stress (SIWS) model, which considers the effects of spray-wall impingement and the resulting formation of wall stress within the Lagrangian spray modeling framework. The primary objective of this paper is to provide a mathematical description of the fundamental physics underlying the model. Subsequently, the proposed model is validated using existing experimental data. The remainder of the study focuses on the practical application of the model to an ignition assistance device. Specifically, this device is installed in a compression ignition engine and designed to enhance ignition in aviation-fueled high-altitude aircraft propulsion systems. The research sheds light on the mechanical impulse caused by the high-speed impact of the spray jet, leading to the accumulation of mechanical stress on the rigid body of the ignition assistance device. Previous studies on fluid–structure interaction have only considered the interaction between the gas phase and the solid wall. However, the SIWS model incorporates the additional impact of the impinging liquid spray jet. Consequently, the simulated stress distribution on the ignition assistance device can be estimated by considering both the gas-phase-induced term and the spray-induced term simultaneously.
- 13 March 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 208
A unified non-equilibrium phase change model for injection flow modeling
- 13 March 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 208
A unified non-equilibrium phase change model for injection flow modeling