HEHosein Banna Motejadded Emrooz

Hosein Banna Motejadded Emrooz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hosein Banna Motejadded Emrooz has a total of 58 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Surface texture dependency of photocatalytic behavior of facile synthesized mesoporous ZnS-ZnO heterostructure under LED illumination

    by Rana Mahdizadeh, Parvaneh Sangpour, Hosein Banna Motejadded Emrooz

    Employing three porous semiconductor particles, the impact of the surface area on dynamic photocatalytic degradation of methylene blue has been investigated under an LED light source. At first, porous ZnS with a relatively high surface area was synthesized via an innovative method in ethanol, which is insoluble for Sulphur precursor (Na2S). This semiconductor was used for the synthesis of porous ZnO and ZnS-ZnO nanocomposites through a simple oxidation treatment in the air atmosphere. The characterization of the synthesized compounds was conducted through different techniques including X-ray diffraction, physisorption of nitrogen, simultaneous thermal analysis, field emission scanning and high-resolution transmission electron microscopy, photoluminescence spectroscopy, FT-IR spectroscopy, Mott-Schottky technique, and visible-ultraviolet spectroscopy. Based on the results, the specific surface areas were reported as 165 m2 g-1, 35 m2 g-1, and 10 m2 g-1 for ZnS, ZnS-ZnO, and ZnO, respectively. Despite ZnS having a higher bandgap (3.3 eV) and lower charge carrier density (9.21⋅1015 cm-3) than ZnS-ZnO, it exhibits better photocatalytic efficiency which emphasizes on the pronounced impact of surface area on the photocatalytic degradation of the selected dye. The efficiency of ZnS in removing organic pollutants is 88%, while ZnO achieves only 43% removal, and the ZnS-ZnO composite exhibits a removal efficiency of 55%. This superior efficiency of ZnS is further supported by its higher surface area, reduced PL intensity and visible-range emissions due to defect states, along with Mott-Schottky analysis confirming trap states that enhance charge separation under LED light. The degradation followed a dynamic process driven by efficient charge transfer and surface interactions.


  • Open Access

    Green synthesis of ZnS/MoS2-decorated porous carbon for photocatalytic degradation of tetracycline under visible light

    by Zahra Amiri, Hosein Banna Motejadded Emrooz, Mobin Safarzadeh Khosrowshahi

    This study investigated a one-step green pyrolysis method inspired by chemical vapor deposition, utilizing melamine and zinc nitrate precursors with varying sulfur content for degradation and adsorption of tetracycline. The method effectively synthesized a ZnS/MoS2 heterojunction composite supported on a porous carbon substrate. It takes advantage of the gases (such as CO2, CO, and H2O) naturally released during pyrolysis to serve as internal activating agents. In contrast to traditional techniques that rely on inert atmospheres, chemical additives, or complicated high-temperature setups, this method minimizes both the ecological footprint and procedural complexity. The optimal composite, PCS2 (synthesized with 2 g of sulfur), exhibited the lowest band gap of 2.91 eV and the highest specific surface area of 216.83 m2 g−1, making it the most effective among the tested samples. This composite achieved 55% adsorption of pollutants and demonstrated a total removal efficiency of 81% for tetracycline. The addition of scavengers revealed that the primary active species in the reaction were holes. This synthesized method shows great promise for preparing heterojunction structures, making it highly suitable for removing organic pollutants from contaminated water.


  • Open Access

    Correction: Wasted rose-derived porous carbons with unique hierarchical heteroatom-enriched structures as a high-performance supercapacitor electrode

    by Amir Mahdi Homayounfard, Mahdi Maleki, Hosein Banna Motejadded Emrooz, Hajar Ghanbari, Samira Mohammadi, Ahmad Shokrieh

    Correction for ‘Wasted rose-derived porous carbons with unique hierarchical heteroatom-enriched structures as a high-performance supercapacitor electrode’ by Amir Mahdi Homayounfard et al., J. Mater. Chem. A, 2024, 12, 22045–22060.


  • Wasted rose-derived porous carbons with unique hierarchical heteroatom-enriched structures as a high-performance supercapacitor electrode

    by Amir Mahdi Homayounfard, Mahdi Maleki, Hosein Banna Motejadded Emrooz, Hajar Ghanbari, Samira Mohammadi, Ahmad Shokrieh

    High-quality and low-cost activated carbons (ACs) are highly considered as high-performance electrode materials for next-generation supercapacitors. Herein, self-heteroatom-doped nanoporous activated carbon (AC) powders were prepared from wasted rose flowers via two different activation approaches, namely, a typical acidic approach with H3PO4 (AC-T) and a green self-activation approach (AC-S). Based on morphological characterizations, the typical activation method resulted in ACs with a surface area of 1124 m2 g−1, while the ACs prepared by the AC-S method retained the initial hierarchical porous rose structure with a higher surface area of 1556 m2 g−1. High-resolution transmission electron microscopy (HRTEM) images revealed extensive graphitized regions in the porous microstructure of the AC-S powders. Electrochemical analysis results demonstrated an outstanding gravimetric capacitance of 539 F g−1 at 1 A g−1 for AC-S in a three-electrode system. In addition, the prepared electrode with AC-S exhibited excellent stability with 95.4% capacitance retention after 6000 cycles. The symmetric supercapacitor device based on this sample also exhibited a high gravimetric capacitance up to 365 F g−1 and an ultra-high energy density of 50.7 W h kg−1 at a power density of 500 W kg−1.


  • Open Access

    Enhanced atmospheric water harvesting efficiency through green-synthesized MOF-801: a comparative study with solvothermal synthesis

    by Mohammad Aghajani Hashjin, Shadi Zarshad, Hosein Banna Motejadded Emrooz, Sadegh Sadeghzadeh

    Adsorption-based atmospheric water harvesting has emerged as a compelling solution in response to growing global water demand. In this context, Metal–organic frameworks (MOFs) have garnered considerable interest due to their unique structure and intrinsic porosity. Here, MOF 801 was synthesized using two different methods: solvothermal and green room temperature synthesis. Comprehensive characterization indicated the formation of MOF-801 with high phase purity, small crystallite size, and excellent thermal stability. Nitrogen adsorption–desorption analysis revealed that green-synthesized MOF-801 possessed an 89% higher specific surface area than its solvothermal-synthesized counterpart. Both adsorbents required activation at a minimum temperature of 90 °C for optimal adsorption performance. Additionally, green-synthesized MOF-801 demonstrated superior adsorption performance compared to solvothermal-synthesized MOF-801, attributed to its small crystal size (around 66 nm), more hydrophilic functional groups, greater specific surface area (691.05 m2/g), and the possibility of having a higher quantity of defects. The maximum water adsorption capacity in green-synthesized MOF-801 was observed at 25 °C and 80% relative humidity, with a value of 41.1 g/100 g, a 12% improvement over the solvothermal-synthesized MOF-801. Remarkably, even at a 30% humidity level, green-synthesized MOF-801 displayed a considerable adsorption capacity of 31.5 g/100 g. Importantly, MOF-801 exhibited long-term effectiveness in multiple adsorption cycles without substantial efficiency decline.


  • Effect of multi-walled carbon nanotube/Porous Carbon/SiO2 on reinforcing of cement mortar matrix: Modeling studies of effective parameters

    by Amirhossein Afshari Aghajari, Mobin Safarzadeh Khosrowshahi, Sina Akhyani, Elahe Ghiyabi, Hosein Banna Motejadded Emrooz, Amir Mohammad Ramezanianpour, Farid Maleki, Hadi Mohammadi


  • Top Cited Papers
    Open Access

    An overview of atmospheric water harvesting methods, the inevitable path of the future in water supply

    by Zahra Ahrestani, Sadegh Sadeghzadeh, Hosein Banna Motejadded Emrooz

    Although science has made great strides in recent years, access to fresh water remains a major challenge for humanity due to water shortage for two-thirds of the world's population.


  • Open Access

    Durable superhydrophobic/superoleophilic melamine foam based on biomass-derived porous carbon and multi-walled carbon nanotube for oil/water separation

    by Hadi Shayesteh, Mobin Safarzadeh Khosrowshahi, Hossein Mashhadimoslem, Farid Maleki, Yahya Rabbani, Hosein Banna Motejadded Emrooz

    In the present study, fabrications of two eco-friendly superhydrophobic/superoleophilic recyclable foamy-based adsorbents for oil/water mixture separation were developed. Hierarchically biomass (celery)-derived porous carbon (PC) and multi-walled carbon nanotube (MWCNT) were firstly synthesized and loaded on pristine melamine foam (MF) by the simple dip-coating approach by combining silicone adhesive to create superhydrophobic/superoleophilic, recyclable, and reusable three-dimensional porous structure. The prepared samples have a large specific surface area of 240 m2/g (MWCNT), 1126 m2/g (PC), and good micro-mesoporous frameworks. The water contact angle (WCA) values of the as-prepared foams, PC/MF and MWCNT/MF, not only were 159.34° ± 1.9° and 156.42° ± 1.6°, respectively but also had oil contact angle (OCA) of equal to 0° for a wide range of oils and organic solvents. Therefore, PC/MF and MWCNT/MF exhibited superhydrophobicity and superoleophilicity properties, which can be considered effective adsorbents in oil/water mixture separations. In this context, superhydrophobic/superoleophilic prepared foams for kind of different oils and organic solvents were shown to have superior separation performance ranges of 54–143 g/g and 46–137 g/g for PC/MF and MWCNT/MF, respectively, suggesting a new effective porous material for separating oil spills. Also, outstanding recyclability and reusability of these structures in the ten adsorption-squeezing cycles indicated that the WCA and sorption capacity has not appreciably changed after soaking into acidic (pH = 2) and alkaline (pH = 12) as well as saline (3.5% NaCl) solutions. More importantly, the reusability and chemical durability of the superhydrophobic samples made them good opportunities for use in different harsh conditions for oil-spill cleanup.


  • Top Cited Papers
    Open Access

    The role of surface chemistry on CO2 adsorption in biomass-derived porous carbons by experimental results and molecular dynamics simulations

    by Mobin Safarzadeh Khosrowshahi, Mohammad Ali Abdol, Hossein Mashhadimoslem, Elnaz Khakpour, Hosein Banna Motejadded Emrooz, Sadegh Sadeghzadeh, Ahad Ghaemi

    Biomass-derived porous carbons have been considered one of the most effective adsorbents for CO2 capture, due to their porous structure and high specific surface area. In this study, we successfully synthesized porous carbon from celery biomass and examined the effect of external adsorption parameters including time, temperature, and pressure on CO2 uptake in experimental and molecular dynamics (MD) simulations. Furthermore, the influence of carbon’s surface chemistry (carboxyl and hydroxyl functionalities) and nitrogen type on CO2 capture were investigated utilizing MD simulations. The results showed that pyridinic nitrogen has a greater tendency to adsorb CO2 than graphitic. It was found that the simultaneous presence of these two types of nitrogen has a greater effect on the CO2 sorption than the individual presence of each in the structure. It was also revealed that the addition of carboxyl groups (O=C–OH) to the carbon matrix enhances CO2 capture by about 10%. Additionally, by increasing the simulation time and the size of the simulation box, the average absolute relative error for simulation results of optimal structure declined to 16%, which is an acceptable value and makes the simulation process reliable to predict adsorption capacity under various conditions.