Jun Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Jun Wang has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Rolando Burgos
Center for Power Electronics Systems (CPES), Virginia Tech, Blacksburg, VA, USA
14 shared publications - Dushan Boroyevich
Center for Power Electronics Systems, Virginia Polytechnic Institute and State University, Blacksburg, VA, USA
11 shared publications - Slavko Mocevic
Virginia Tech
7 shared publications - Fei Lu
Department of Electrical and Computer Engineering, Lehigh University, Bethlehem, PA, USA
6 shared publications - Reza Kheirollahi
Department of Electrical and Computer Engineering, Drexel University, Philadelphia, PA, USA
6 shared publications - Hua Zhang
Department of Electrical and Computer Engineering, Lehigh University, Bethlehem, PA, USA
5 shared publications
Latest Publications
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (7) , 12118-12134
Unified Synchronization Control of Grid-Forming Voltage-Source Converter for Maximum Inertia Power Support With Enhanced Synchronization and DC-Link Voltage Stability
Grid-forming (GFM) voltage-source converters (VSCs) are expected to provide inertia power support during grid-frequency disturbances and grid-voltage phase-angle jumps. However, the existing synchronization control methods have unsatisfactory performance to control the GFM VSCs to provide the maximum inertia power support while achieving robust synchronization and DC-link voltage control during these transient events. To bridge this gap, this paper proposes a novel unified synchronization control (USC) strategy that integrates an active power compensator with a DC-link voltage compensator through a parallel configuration. With the proposed USC, the GFM VSC can autonomously and seamlessly switch its operation between two modes: a voltage-controlled DC-side source (VC-DCS) mode when the DCS current is within the limit and a current-controlled DCS (CC-DCS) mode when the DCS current reaches the limit, while providing the maximum inertia power support. Compared to the state-of-the-art power synchronization control (PSC) and DC-link voltage synchronization control (DVSC) methods, the USC significantly enhances the transient oscillation damping as well as synchronization and DC-link voltage stability. A parameter design methodology for the USC is presented. Finally, the superiority of the proposed USC over the PSC and DVSC is validated by a loop-gain evaluation using simulation as well as grid-frequency step change and grid-voltage phase-angle jump tests using a GFM VSC hardware testbed.
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41  (7) , 12118-12134
Unified Synchronization Control of Grid-Forming Voltage-Source Converter for Maximum Inertia Power Support With Enhanced Synchronization and DC-Link Voltage Stability
Grid-forming (GFM) voltage-source converters (VSCs) are expected to provide inertia power support during grid-frequency disturbances and grid-voltage phase-angle jumps. However, the existing synchronization control methods have unsatisfactory performance to control the GFM VSCs to provide the maximum inertia power support while achieving robust synchronization and DC-link voltage control during these transient events. To bridge this gap, this paper proposes a novel unified synchronization control (USC) strategy that integrates an active power compensator with a DC-link voltage compensator through a parallel configuration. With the proposed USC, the GFM VSC can autonomously and seamlessly switch its operation between two modes: a voltage-controlled DC-side source (VC-DCS) mode when the DCS current is within the limit and a current-controlled DCS (CC-DCS) mode when the DCS current reaches the limit, while providing the maximum inertia power support. Compared to the state-of-the-art power synchronization control (PSC) and DC-link voltage synchronization control (DVSC) methods, the USC significantly enhances the transient oscillation damping as well as synchronization and DC-link voltage stability. A parameter design methodology for the USC is presented. Finally, the superiority of the proposed USC over the PSC and DVSC is validated by a loop-gain evaluation using simulation as well as grid-frequency step change and grid-voltage phase-angle jump tests using a GFM VSC hardware testbed.
- 10 January 2024
- Published by SAGE Publications in Journal of Intelligent & Fuzzy Systems: Applications in Engineering and Technology
- Vol. 46  (1) , 493-504
Personal safety monitoring system of electric power construction site based on AIoT Technology
For the purpose of real-time monitoring the hazard information on the electric power construction site, a personal safety monitoring system based on Artificial intelligence internet of things (AIoT) technology is designed. After the system sensing layer collects the gas information of the construction site through the gas sensor, limit current oxygen sensor and DS1820B temperature sensor, the edge computing device of the edge layer directly stores its calculation in the database of the platform layer through the data gateway. The Artificial Intelligence (AI) analysis module of this layer invokes the monitoring data of the power construction site of the database, and uses the personal safety identification method of the power construction site based on artificial intelligence technology, to complete the abnormal identification of monitoring data and realize personal safety monitoring. In addition, the system is also equipped with a power-fail detection module, which can collect the working voltage through the voltage transformer and compare it with the mains power standard to judge whether there is a power-fail risk, so as to prevent the problem of threatening personal safety due to the power-fail of the energized equipment. After testing, the system can monitor the operation status of the construction site in real time to protect personal safety.
- 10 January 2024
- Published by SAGE Publications in Journal of Intelligent & Fuzzy Systems: Applications in Engineering and Technology
- Vol. 46  (1) , 493-504
Personal safety monitoring system of electric power construction site based on AIoT Technology
For the purpose of real-time monitoring the hazard information on the electric power construction site, a personal safety monitoring system based on Artificial intelligence internet of things (AIoT) technology is designed. After the system sensing layer collects the gas information of the construction site through the gas sensor, limit current oxygen sensor and DS1820B temperature sensor, the edge computing device of the edge layer directly stores its calculation in the database of the platform layer through the data gateway. The Artificial Intelligence (AI) analysis module of this layer invokes the monitoring data of the power construction site of the database, and uses the personal safety identification method of the power construction site based on artificial intelligence technology, to complete the abnormal identification of monitoring data and realize personal safety monitoring. In addition, the system is also equipped with a power-fail detection module, which can collect the working voltage through the voltage transformer and compare it with the mains power standard to judge whether there is a power-fail risk, so as to prevent the problem of threatening personal safety due to the power-fail of the energized equipment. After testing, the system can monitor the operation status of the construction site in real time to protect personal safety.
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12  (1) , 997-1010
Soft Turn-Off DC Solid-State Circuit Breakers With Flexible Dual Tripping Schemes
A novel solid-state circuit breaker (SSCB) topology with two combined tripping schemes is proposed in this paper: 1) fault current bypass (FCB) tripping and 2) soft turn-off tripping by transient commutation current injection (TCCI). There are four main contributions in this work. 1) Flexible combined dual tripping schemes are realized by one single topology. 2) The traditional monotonous hard switching FCB tripping with fast isolation speed cannot handle heavy load faults due to gate oscillations caused by higher d i /d t and d v /d t . Compared to pure FCB tripping, the combined soft turn-off tripping by TCCI in this work realizes zero current switching (ZCS) for the semiconductor switch to suppress its gate oscillations at heavy load fault interruption. 3) The capacitors in the TCCI circuits are automatically self-charged by the dc bus during the off state of SSCB, which greatly simplifies the design by getting rid of external capacitor charging circuits. 4) Reclosing and immediate reopening operations are realized, which enhances the practicality of this work A 375 V/20 A SSCB is designed and developed to experimentally validate the proposed dual tripping schemes at light load fault (57 A) and heavy load fault (325 A). The SSCB demonstrates an ultrafast response speed of 5.2 ÎĽs with FCB tripping and 19.6 ÎĽs with TCCI soft turn-off tripping. The reclosing and reopening operation is also validated based on IEEE Standard C37.14. This paper is accompanied by a slide as multimedia material demonstrating the contributions of the presented work.
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12  (1) , 997-1010
Soft Turn-Off DC Solid-State Circuit Breakers With Flexible Dual Tripping Schemes
A novel solid-state circuit breaker (SSCB) topology with two combined tripping schemes is proposed in this paper: 1) fault current bypass (FCB) tripping and 2) soft turn-off tripping by transient commutation current injection (TCCI). There are four main contributions in this work. 1) Flexible combined dual tripping schemes are realized by one single topology. 2) The traditional monotonous hard switching FCB tripping with fast isolation speed cannot handle heavy load faults due to gate oscillations caused by higher d i /d t and d v /d t . Compared to pure FCB tripping, the combined soft turn-off tripping by TCCI in this work realizes zero current switching (ZCS) for the semiconductor switch to suppress its gate oscillations at heavy load fault interruption. 3) The capacitors in the TCCI circuits are automatically self-charged by the dc bus during the off state of SSCB, which greatly simplifies the design by getting rid of external capacitor charging circuits. 4) Reclosing and immediate reopening operations are realized, which enhances the practicality of this work A 375 V/20 A SSCB is designed and developed to experimentally validate the proposed dual tripping schemes at light load fault (57 A) and heavy load fault (325 A). The SSCB demonstrates an ultrafast response speed of 5.2 ÎĽs with FCB tripping and 19.6 ÎĽs with TCCI soft turn-off tripping. The reclosing and reopening operation is also validated based on IEEE Standard C37.14. This paper is accompanied by a slide as multimedia material demonstrating the contributions of the presented work.
- 3 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11  (2) , 1827-1837
PESNet 3.0: A WRN-Based Communication Network With ±0.5 ns Synchronization Error for Large-Scale Modular Power Converters
Emerging large-scale silicon-carbide (SiC)-based modular power converters are pursuing high-performance distributed control systems (DCSs). In particular, fast-switching-enabled novel control schemes raise the need for minimal synchronization error (SE) of communication networks. This paper presents the development of a proposed power electronics system network (PESNet) 3.0 that features a sub-nanosecond SE and gigabits-per-second data rate. The White Rabbit Network technology, originally developed for particle accelerators, has been embedded in PESNet 3.0 and tailored to be suited for large-scale high-frequency modular power converters. A simplified node-to-node phase-locked loop (N2N-PLL) and an improved precision time protocol model has been proposed to lock both the frequency and phase of two independent clocks on two adjacent nodes. Subsequently, the stability analysis of the N2N-PLL is carried out with its closed-loop transfer function verified by digital perturbation injection. Finally, the experimental validation of PESNet 3.0 is demonstrated at both controller and converter levels. The latter is on a first-of-it-kind 10 kV SiC-MOSFET-based modular converter prototype operating at 12 kV dc-link voltage, 10 kHz switching frequency, and above 100V/ns slew rate, verifying ±0.5 ns SE at 5 Gbps data rate.
- 3 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11  (2) , 1827-1837
PESNet 3.0: A WRN-Based Communication Network With ±0.5 ns Synchronization Error for Large-Scale Modular Power Converters
Emerging large-scale silicon-carbide (SiC)-based modular power converters are pursuing high-performance distributed control systems (DCSs). In particular, fast-switching-enabled novel control schemes raise the need for minimal synchronization error (SE) of communication networks. This paper presents the development of a proposed power electronics system network (PESNet) 3.0 that features a sub-nanosecond SE and gigabits-per-second data rate. The White Rabbit Network technology, originally developed for particle accelerators, has been embedded in PESNet 3.0 and tailored to be suited for large-scale high-frequency modular power converters. A simplified node-to-node phase-locked loop (N2N-PLL) and an improved precision time protocol model has been proposed to lock both the frequency and phase of two independent clocks on two adjacent nodes. Subsequently, the stability analysis of the N2N-PLL is carried out with its closed-loop transfer function verified by digital perturbation injection. Finally, the experimental validation of PESNet 3.0 is demonstrated at both controller and converter levels. The latter is on a first-of-it-kind 10 kV SiC-MOSFET-based modular converter prototype operating at 12 kV dc-link voltage, 10 kHz switching frequency, and above 100V/ns slew rate, verifying ±0.5 ns SE at 5 Gbps data rate.
- 26 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38  (1) , 1144-1154
Fast Y-Type Thyristor-Based DC SSCB Using Complementary Commutation in a Capacitor–Capacitor Pair Structure
This article proposes a new thyristor-based dc solid-state circuit breaker (SSCB) named Y-type. Main contributions focus on a new complementary commutation circuit including a capacitor–capacitor pair, which features three remarkable advantages. First, a fast commutation is achieved using a countercurrent pulse injection by the capacitor–capacitor pair structure. Second, metal-oxide varistors (MOVs) are disconnected from the power line when SSCB is off , which solves the reliability issue due to the MOV degradation and enhances the voltage utilization rate of the main switch. Third, benefiting from the capacitor–capacitor pair structure, reliable reclosing and rebreaking are obtained for practical applications. Experiments are conducted on a 400 V/120 A prototype to validate the proposed Y-SSCB. The peak voltage on the main and auxiliary thyristors reaches 773 and 400 V, respectively. Also, the peak voltage on the auxiliary capacitors pair reaches 740 and 400 V. The Y-SSCB achieves a fast reaction time of 80 μs in interrupting 120 A short-circuit fault current.
- 26 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38  (1) , 1144-1154
Fast Y-Type Thyristor-Based DC SSCB Using Complementary Commutation in a Capacitor–Capacitor Pair Structure
This article proposes a new thyristor-based dc solid-state circuit breaker (SSCB) named Y-type. Main contributions focus on a new complementary commutation circuit including a capacitor–capacitor pair, which features three remarkable advantages. First, a fast commutation is achieved using a countercurrent pulse injection by the capacitor–capacitor pair structure. Second, metal-oxide varistors (MOVs) are disconnected from the power line when SSCB is off , which solves the reliability issue due to the MOV degradation and enhances the voltage utilization rate of the main switch. Third, benefiting from the capacitor–capacitor pair structure, reliable reclosing and rebreaking are obtained for practical applications. Experiments are conducted on a 400 V/120 A prototype to validate the proposed Y-SSCB. The peak voltage on the main and auxiliary thyristors reaches 773 and 400 V, respectively. Also, the peak voltage on the auxiliary capacitors pair reaches 740 and 400 V. The Y-SSCB achieves a fast reaction time of 80 μs in interrupting 120 A short-circuit fault current.
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 6, 1262-1266
Static Voltage Assessment based on Electro-thermal coupling V-Q Sensitivity Analysis
Although the traditional V-Q sensitivity can quickly determine the stability of the system bus voltage, its mathematical model only considers the electrical model of the line and ignores the electro-thermal coupling relationship of the line under actual conditions. Therefore, the use of traditional model calculation results as a reference for the actual bus voltage stability judgment has a large deviation. With this as a background, this paper establishes an electro-thermal coupled power flow model, which is based on the IEEE standard heat balance equation and regards the transmission line resistance as the state variable of the power flow. Then, based on the expansion of the Jacobian matrix in the improved power flow model, a V-Q sensitivity analysis method considering the electro-thermal coupling is proposed, and the calculation example is compared and analyzed with the traditional model in different seasons. The results show that the traditional model ignores the influence of the line temperature and resistance due to the electric and heat balance, which will introduce certain errors in the calculation results for different seasons.
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 6, 1262-1266
Static Voltage Assessment based on Electro-thermal coupling V-Q Sensitivity Analysis
Although the traditional V-Q sensitivity can quickly determine the stability of the system bus voltage, its mathematical model only considers the electrical model of the line and ignores the electro-thermal coupling relationship of the line under actual conditions. Therefore, the use of traditional model calculation results as a reference for the actual bus voltage stability judgment has a large deviation. With this as a background, this paper establishes an electro-thermal coupled power flow model, which is based on the IEEE standard heat balance equation and regards the transmission line resistance as the state variable of the power flow. Then, based on the expansion of the Jacobian matrix in the improved power flow model, a V-Q sensitivity analysis method considering the electro-thermal coupling is proposed, and the calculation example is compared and analyzed with the traditional model in different seasons. The results show that the traditional model ignores the influence of the line temperature and resistance due to the electric and heat balance, which will introduce certain errors in the calculation results for different seasons.
- 3 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 3  (3) , 572-582
High-Frequency High Step-Up Inductive Power Transfer-Based Capacitor Charger in Active Injection DC Circuit Breakers
This article investigates the application of inductive power transfer (IPT) based converters as capacitor chargers for dc circuit breakers (DCCBs) including active injection circuits (AIC). AIC generates resonant countercurrent pulses to achieve transient current commutation. There are three main contributions. First, a high-frequency and high step-up wireless inductive series-parallel (WISP) converter is applied to charge the injection capacitor of AIC, which achieves reliable voltage isolation and constant voltage output with a simple structure. Second, WISP converter is optimized for DCCBs with three objectives: 1) reducing transient time, 2) reducing transient and steady-state power loss, and 3) enhancing compactness. Four parameters impacting the transient are analyzed through LTspice simulations and experiments, namely the input dc voltage, voltage step-up ratio, quality factor, and the injection capacitor. Third, a burst switching mode control is proposed to reduce steady-state power loss. An optimized WISP converter operating at 1 MHz with a voltage gain of 8.33 is implemented and applied to a 380 V/50 A/5.2 ÎĽs AIC SSCB. Based on the experimental results, a 10 ÎĽF load capacitor is charged to 80 V in 2.37 ms and 90 V in 2.9 ms. It presents 66.7% efficiency during transient and 99.6% energy saving during steady-state while keeping the output voltage ripple within 2%.
- 3 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 3  (3) , 572-582
High-Frequency High Step-Up Inductive Power Transfer-Based Capacitor Charger in Active Injection DC Circuit Breakers
This article investigates the application of inductive power transfer (IPT) based converters as capacitor chargers for dc circuit breakers (DCCBs) including active injection circuits (AIC). AIC generates resonant countercurrent pulses to achieve transient current commutation. There are three main contributions. First, a high-frequency and high step-up wireless inductive series-parallel (WISP) converter is applied to charge the injection capacitor of AIC, which achieves reliable voltage isolation and constant voltage output with a simple structure. Second, WISP converter is optimized for DCCBs with three objectives: 1) reducing transient time, 2) reducing transient and steady-state power loss, and 3) enhancing compactness. Four parameters impacting the transient are analyzed through LTspice simulations and experiments, namely the input dc voltage, voltage step-up ratio, quality factor, and the injection capacitor. Third, a burst switching mode control is proposed to reduce steady-state power loss. An optimized WISP converter operating at 1 MHz with a voltage gain of 8.33 is implemented and applied to a 380 V/50 A/5.2 ÎĽs AIC SSCB. Based on the experimental results, a 10 ÎĽF load capacitor is charged to 80 V in 2.37 ms and 90 V in 2.9 ms. It presents 66.7% efficiency during transient and 99.6% energy saving during steady-state while keeping the output voltage ripple within 2%.
- 24 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37  (8) , 9944-9958
Design and Multiobjective Optimization of an Auxiliary Wireless Power Transfer Converter in Medium-Voltage Modular Conversion Systems
This article proposes an optimized design for a wireless power transfer converter serving as an auxiliary power supply in a medium-voltage, high $\mathrm{d}v/\mathrm{d}t$ modular conversion system. A CLLC-CL circuit topology is implemented to generate a load-independent output voltage with a coupling-coefficient-independent resonant frequency. The output voltage of the circuit can be tuned by changing one pair of resonant LC parameters, which decouples the circuit gain from the coil design. Essential parameters of coil and magnet are extracted analytically or numerically to avoid time-consuming 3-D finite element analysis simulations for the subsequent optimization. After the design of the circuit and coil, a multiobjective optimization is carried out with objectives being efficiency, isolation capacitance, and insulation rating of the converter. Finally, experiments demonstrate a 48- to 48-V dc–dc converter with 100 W output power, 92.78% efficiency, 2.78 pF isolation capacitance, and 27 kV insulation rating to validate the optimization result.
- 24 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37  (8) , 9944-9958
Design and Multiobjective Optimization of an Auxiliary Wireless Power Transfer Converter in Medium-Voltage Modular Conversion Systems
This article proposes an optimized design for a wireless power transfer converter serving as an auxiliary power supply in a medium-voltage, high $\mathrm{d}v/\mathrm{d}t$ modular conversion system. A CLLC-CL circuit topology is implemented to generate a load-independent output voltage with a coupling-coefficient-independent resonant frequency. The output voltage of the circuit can be tuned by changing one pair of resonant LC parameters, which decouples the circuit gain from the coil design. Essential parameters of coil and magnet are extracted analytically or numerically to avoid time-consuming 3-D finite element analysis simulations for the subsequent optimization. After the design of the circuit and coil, a multiobjective optimization is carried out with objectives being efficiency, isolation capacitance, and insulation rating of the converter. Finally, experiments demonstrate a 48- to 48-V dc–dc converter with 100 W output power, 92.78% efficiency, 2.78 pF isolation capacitance, and 27 kV insulation rating to validate the optimization result.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
A Compact High-Power Single-Turn Inductor for 6 kV SiC-based Power Electronics Building Blocks
Based on our previous work, this paper presents the follow-up design and testing of a single-turn magnetic-core inductor for 6 kV power electronics building blocks (PEBBs) using 10 kV SiC MOSFET modules. The specifications of the inductor were derived from the switching-cycle control (SCC) principle. The single-turn magnetic core inductor with shielded solid insulation has been concluded to be the most suitable solution based on our prior work. The shielding layer facilitates the insulation design, but it has some side-effects such as shileding losses, shield termination and induced displacement current. Beyond our previous work, a double-layer termination structure is proposed to shrink the size of the termination structure and minimize the electric field strength in air, and quantitative study is conducted regarding the dimensions and permittivity. The displacement current is investigated and recommendations are provided. Two fabrication process methods for winding insulation are investigated and compared, and the one discussed in this paper is chosen to facilitate the mass production for modular multilevel converters (MMC) application. The proposed fabrication process gives 7.34 kV PDIV which meets the insulation requirement. The converter-level tests confirm the effectiveness of the grounding current reduction method.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
A Compact High-Power Single-Turn Inductor for 6 kV SiC-based Power Electronics Building Blocks
Based on our previous work, this paper presents the follow-up design and testing of a single-turn magnetic-core inductor for 6 kV power electronics building blocks (PEBBs) using 10 kV SiC MOSFET modules. The specifications of the inductor were derived from the switching-cycle control (SCC) principle. The single-turn magnetic core inductor with shielded solid insulation has been concluded to be the most suitable solution based on our prior work. The shielding layer facilitates the insulation design, but it has some side-effects such as shileding losses, shield termination and induced displacement current. Beyond our previous work, a double-layer termination structure is proposed to shrink the size of the termination structure and minimize the electric field strength in air, and quantitative study is conducted regarding the dimensions and permittivity. The displacement current is investigated and recommendations are provided. Two fabrication process methods for winding insulation are investigated and compared, and the one discussed in this paper is chosen to facilitate the mass production for modular multilevel converters (MMC) application. The proposed fabrication process gives 7.34 kV PDIV which meets the insulation requirement. The converter-level tests confirm the effectiveness of the grounding current reduction method.
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Smart Grid
- Vol. 13  (5) , 3915-3928
DC Circuit Breakers: A Technology Development Status Survey
DC circuit breakers (DCCBs) play a significant role in obtaining the reliability and stability of DC power systems. Selective and fast isolating of faults minimizes the power supply outages to end electricity users and protects the power converters implemented in the DC system. During the last decades, DCCBs have been deeply investigated in industry and academia. There has been impressive progress in terms of efficiency, response time, power-density, lifetime, and electrical operating ratings. Introducing wide bandgap (WBG) devices further has motivated researchers to propose more efficient and novel topologies. This paper provides a point of reference and a background review for DCCBs from novel aspects, fulfilling absent parts in the literature. The elaborated subjects include current commutation circuitry, DCCBs trip-curves developments, newly added functions to DCCBs, as well as marketing analysis. The advancements of DCCBs are surveyed and development needs are recognized. This paper aims to identify the future research needs of DCCBs for emerging DC power systems.
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Smart Grid
- Vol. 13  (5) , 3915-3928
DC Circuit Breakers: A Technology Development Status Survey
DC circuit breakers (DCCBs) play a significant role in obtaining the reliability and stability of DC power systems. Selective and fast isolating of faults minimizes the power supply outages to end electricity users and protects the power converters implemented in the DC system. During the last decades, DCCBs have been deeply investigated in industry and academia. There has been impressive progress in terms of efficiency, response time, power-density, lifetime, and electrical operating ratings. Introducing wide bandgap (WBG) devices further has motivated researchers to propose more efficient and novel topologies. This paper provides a point of reference and a background review for DCCBs from novel aspects, fulfilling absent parts in the literature. The elaborated subjects include current commutation circuitry, DCCBs trip-curves developments, newly added functions to DCCBs, as well as marketing analysis. The advancements of DCCBs are surveyed and development needs are recognized. This paper aims to identify the future research needs of DCCBs for emerging DC power systems.