JLJing Lv

Jing Lv

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jing Lv has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Investigation on the Mechanical Properties and Microstructure of Basalt Fiber Reinforced Engineered Cementitious Composite

    by Qiang Du, Changlu Cai, Jing Lv, Jiao Wu, Ting Pan, Jie Zhou

    This study investigated fundamental mechanical properties of a basalt fiber reinforced engineered cementitious composite (BF-ECC) with different volume fractions of basalt fiber (BF), water–binder ratio (W/B) and fly ash (FA) content. The compressive strength, splitting tensile strength, flexural strength and static modulus of BF-ECC were studied at 3, 28 and 56 days, respectively, to explore their development along the ages. Furthermore, the scanning electron microscopy (SEM) analysis was conducted to evaluate the microstructure of BF-ECC. Experiment results demonstrated that bond quality between the BF and the matrix is good, which leads to a significant increase in the flexural strength and splitting tensile strength. The pozzolanic effect of FA obviously improved the splitting tensile and flexural strength of BF-ECC after 56 days of curing, and the appropriate content of the FA content in the BF-ECC ranges from 50% to 60%.


  • Open Access

    A New Composite Slab Using Crushed Waste Tires as Fine Aggregate in Self-Compacting Lightweight Aggregate Concrete

    by Jing Lv, Tianhua Zhou, Hanheng Wu, Liurui Sang, Zuoqian He, Gen Li, Kaikai Li

    A composite slab comprised of self-compacting rubber lightweight aggregate concrete (SCRLC) and profiled steel sheeting is a new type of structural element with a series of superior properties. This paper presents an experimental research and finite element analysis (FEA) of the flexural behavior of composite slabs consisting of SCRLC to develop a new floor system. Four composite slabs specimens with different shear spans (450 mm and 800 mm) and SCRLC (0% and 30% in rubber particles substitution ratio) are prepared, and the flexural properties including failure modes, deflection at mid-span, profiled steel sheeting, and concrete surface stain at mid-span and end slippage are investigated by four-point bending tests. The experimental results indicate that applying SCRLC30 in composites slabs will improve the anti-cracking ability under the loading of composite slabs compared with composite slabs consisting of self-compacting lightweight aggregate concrete (SCLC). FEM on the flexural properties of SCRLC composites slabs show that the yield load, ultimate load, and deflection corresponding to the yield load and the ultimate load of composite slabs drop as the rubber particles content increases in SCRLC. The variation of SCRLC strength has less impact on the flexural bearing capacity of corresponding composite slabs. Based on the traditional calculated method of the ultimate bending moment of normal concrete (NC) composite slabs, a modified calculated method for the ultimate bending moment of SCRLC composite slabs is proposed.


  • Open Access

    Investigation and Application of a New Low-Carbon Material (Preplaced Aggregate Concrete) in Concrete-Filled Steel Tube Stub Columns

    by Jing Lv, Tianhua Zhou, Kunlun Li

    As a new low-carbon material, development of preplaced aggregate concrete (PAC) will achieve huge economic and social benefits. However, few existing research is focused on applying PAC in structural elements. This paper is attempt to apply PAC in concrete-filled steel tube (CFST) stub columns and the bearing behaviors of PAC-filled steel tube (PACFST) stub columns under axial compression are also experimentally investigated. The results indicate that the failure modes of PACFST stub columns are all drum-like failure mode which are analogous to that of CFST stub columns. The axial load-axial strain curves of PACFST stub columns can be roughly divided into elastic stage, elastic-plastic stage and plastic stage. Under the similar ultimate load, the ultimate strains are a bit smaller than that of CFST stub columns. Comparison of the results of ultimate load of PACFST stub columns calculated using the existing relevant standards for the bearing capacity calculation methods of CFST stub columns, GB 50936 and JGJ 138 are much more suitable to assess the bearing capacity of PACFST stub columns. Approximately 15%~20% saving in cement consumption will be accomplished with popularization and utilization of PACFST stub columns as compared with CFST stub columns.


  • Open Access

    Development and Investigation of a New Low-Cement-Consumption Concrete—Preplaced Aggregate Concrete

    by Jing Lv, Tianhua Zhou, Kunlun Li

    Reducing consumption of cement in concrete will achieve huge benefits in decline of carbon emission, conservation of natural resources and reduction of the cost of concrete. In this paper, the low-cement-consumption concrete, preplaced aggregate concrete (PAC), is prepared and 12 types of mixtures including four water–binder ratios (W/B) and three sand–binder ratios (S/B) are designed to detect the effect of W/B and S/B on the mechanical properties and failure mechanism of PAC. Experimental and analytic results indicate that the cubic compressive strength of PAC, splitting tensile strength of PAC and elastic modulus of PAC decrease with increase in W/B and S/B. At a similar compressive strength, more than 20% increment of elastic modulus of PAC is achieved when compared with normal concrete (NC); the descent stage of stress–strain curves of PAC are steeper than that of NC and the peak strains of PAC is lower than that of NC. Guo’s model with suitable values of parameters a and b can be used to describe the stress–strain relationship of PAC. Replacing NC by PAC in concrete structures will save 15–20% cement and achieve great environmental and economic benefits.


  • Open Access

    Research on the Bond Behavior of Preplaced Aggregate Concrete-Filled Steel Tube Columns

    by Jing Lv, Tianhua Zhou, Qiang Du, Kunlun Li, Liangwei Jin

    In order to investigate the bond behavior of preplaced aggregate concrete-filled steel tube (CFT-PAC) columns and the difference of bond behavior between CFT-PAC columns and normal concrete-filled steel tube (CFT-NC) columns, a total of 11 columns were prepared and the push-out tests were conducted. The experimental parameters included the type of concrete (preplaced aggregate concrete and normal concrete), concrete strength (C40, C50 and C60), cross-section dimension (D = 219 mm, 299 mm and 351 mm) and the thickness of steel tube (t = 6 mm and 8 mm). The results indicated that the CTF-PAC columns had a similar load-slip curves with CFT-NC columns. The bond stresses of the CFT-PAC columns were higher than that of the PAC-NC columns at the same concrete strength. Increasing compressive strength of PAC increased the critical bond strength and bond strength of CFT-PAC columns. With an increase of the L/D ratio, both of the slip corresponding to peak load and bond strength of CFT-PAC columns exhibited an increasing trend. A rise in the D/t ratio led to a decrease in the bond stress of CFT-PAC columns and an increase in slip corresponding to the peak load of CFT-PAC columns. The proposed bond stress–slip relationship model considerably matched the bond stress–slip relationship of CFT-PAC columns.


  • Open Access

    Evaluation of Stress–Strain Behavior of Self-Compacting Rubber Lightweight Aggregate Concrete under Uniaxial Compression Loading

    by Jing Lv, Tianhua Zhou, Qiang Du, Kunlun Li, Kai Sun

    The recycling of waste tires in lightweight aggregate concrete (LC) would achieve huge environmental and societal benefits, but the effects of rubber particles on the partial properties of LC are not clear (e.g., the stress–strain relationship). In this paper, uniaxial compressive experiments were conducted to evaluate the stress–strain relationship of self-compacting rubber lightweight aggregate concrete (SCRLC). Rubber particles were used to replace sand by volume, and substitution percentages of 0%, 10%, 20%, 30%, 40%, and 50% were set as influence factors. Experimental results indicate that with increased rubber particles substitution percentage, the cubic compressive strength and axial compressive strength of SCRLC decreased, while the failure modes of SCRLC prism specimens gradually changed from brittle to ductile failure. As the rubber particles substitution percentage increased from 0% to 50%, the peak strain of SCRLC increased whereas peak stress, elastic modulus, and peak secant modulus of SCRLC deceased, the descending stage of stress–strain curves became softer. The rubber particles substitution percentage of 30% was the critical point at which an obvious change in the properties of SCRLC occurred. Based on the data collected from experimental studies, a predictive model for SCRLC was established and a further prediction of the SCRLC stress–strain relationship was given.


  • Open Access

    Shrinkage Properties of Self-Compacting Rubber Lightweight Aggregate Concrete: Experimental and Analytical Studies

    by Jing Lv, Tianhua Zhou, Kunlun Li, Kai Sun

    The shrinkage properties of self-compacting rubber lightweight aggregate concrete (SCRLC) were investigated by experimental and analytical studies in this paper. Rubber particles were used to substitute the sand in SCRLC by volume and rubber particles substitution percentages were 10%, 20%, 30%, 40% and 50%. The experimental results showed that the shrinkage strains of SCRLC increased with an increase of rubber particles substitution percentage. On the basis of China Academy of Building Research model and experimental data, a predictive model for describing the shrinkage strains of SCRLC was established. After analytical study, it was revealed that rubber particles substitution percentage of 80% in SCRLC might be the upper limit of substitution percentage; if the rubber particles substitution percentage was larger than 80%, the shrinkage strains of SCRLC would exceed the limiting value stipulated in JGJ51-2002 and the durability of SCRLC would drop to a worse status.


  • Open Access

    Mechanical Properties of Sandstone Cement-Stabilized Macadam

    by Qiang Du, Ting Pan, Jing Lv, Jie Zhou, Qingwei Ma, Qiang Sun

    Application of sandstone in cement-stabilized macadam (CSM) is an effective way to utilize sandstone. To determine the feasibility of using sandstone as a CSM aggregate, a series of experimental investigations, such as unconfined compressive strength (UCS) tests, Brazilian splitting tests and freeze-thaw cycle tests, were conducted on sandstone cement-stabilized macadam (SCSM). Three mixed variables, covering the cement content, aggregate type and curing period, were set as influence factors. The testing results indicated that the UCS, indirect tensile strength (ITS) and frost resistance property of the test-pieces increased with cement content and curing age. Considering the asphalt pavement design specifications for China, the UCS and ITS values of the SCSM complied with the requirements of light traffic road construction before freeze-thaw cycles. However, the SCSM subjected to freezing and thawing meets the requirements only when the cement content is 4.5%. Therefore, it is noteworthy that CSM containing sandstone aggregates should be applied with caution in cold region because of insufficient freeze resistance.