Masakazu Haruta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Masakazu Haruta has a total of 169 co-authors. Here are the top co-authors by number of shared publications:
- Minoru Inaba
Doshisha University
15 shared publications Takayuki Doi
Doshisha University, Tatara-Miyakodani, Kyotanabe, Kyoto 610-0321, Japan
14 shared publications- Shigeru Horii
Kochi University of Technology
10 shared publications T. Maeda
Kochi Univ Technol, Sch Environm Sci & Engn, Kami, Kochi 7828502, Japan
9 shared publications- Takayuki Doi
Department of Molecular Chemistry and Biochemistry, Doshisha University
9 shared publications J. Shimoyama
Univ Tokyo, Dept Appl Chem, Bunkyo Ku, Tokyo 1138656, Japan
8 shared publications
Latest Publications
- Open Access
- 6 June 2025
- Published by The Electrochemical Society of Japan in Electrochemistry
- Vol. 93 (6) , 063022
Improvement of Short-Circuit Tolerance of Garnet Type Solid Electrolyte Li6.4La3Zr1.4Ta0.6O12 by Li2WO4 and Al2O3 Sintering Aids and La Deficiency
Access full-text academic articles: J-STAGE is an online platform for Japanese academic journals.
- 6 June 2025
- Published by The Electrochemical Society of Japan in Electrochemistry
- Vol. 93 (6) , 063022
Open AccessImprovement of Short-Circuit Tolerance of Garnet Type Solid Electrolyte Li6.4La3Zr1.4Ta0.6O12 by Li2WO4 and Al2O3 Sintering Aids and La Deficiency
Access full-text academic articles: J-STAGE is an online platform for Japanese academic journals.
- 1 February 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (2) , 020519
Perfluoroinated Ionomer as an Artificial SEI for Silicon Nano-Flake Anode in LiTFSI/Tetraglyme Solvate Ionic Liquid
Cycle performance of silicon nano-flake powder (LeafPower ® Si) anodes was improved by coating of perfluorosulfonic acid (PFSA) polymers (Nafion ® and Aquivion ® ) as an artificial solid electrolyte interphase (SEI). The Si electrodes were coated with PFSA ionomer by addition of PFSA ionomer solution to aqueous slurry of the Si composite electrode. H + -type Nafion ® -coated Si electrodes demonstrated improved capacity retentions and Coulombic efficiencies owing to the formation of a LiF-rich SEI composed of reductive decomposition products of Nafion ® . The Nafion ® coating suppressed the increase in polarization and the electrode swelling upon cycling because the LiF-rich SEI effectively suppressed electrolyte decomposition. Li + and Cs + -type Nafion ® and H + -type Aquivion ® , which has a shorter side chain than Nafion ® , provided similar positive effects on cycle performance of the Si electrodes. Furthermore, the Si electrodes achieved good cycleability up to 500 cycles owing to synergy effects of the Nafion ® coating and an SEI-forming additive of fluoroethylene carbonate (FEC).
- 1 February 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (2) , 020519
Perfluoroinated Ionomer as an Artificial SEI for Silicon Nano-Flake Anode in LiTFSI/Tetraglyme Solvate Ionic Liquid
Cycle performance of silicon nano-flake powder (LeafPower ® Si) anodes was improved by coating of perfluorosulfonic acid (PFSA) polymers (Nafion ® and Aquivion ® ) as an artificial solid electrolyte interphase (SEI). The Si electrodes were coated with PFSA ionomer by addition of PFSA ionomer solution to aqueous slurry of the Si composite electrode. H + -type Nafion ® -coated Si electrodes demonstrated improved capacity retentions and Coulombic efficiencies owing to the formation of a LiF-rich SEI composed of reductive decomposition products of Nafion ® . The Nafion ® coating suppressed the increase in polarization and the electrode swelling upon cycling because the LiF-rich SEI effectively suppressed electrolyte decomposition. Li + and Cs + -type Nafion ® and H + -type Aquivion ® , which has a shorter side chain than Nafion ® , provided similar positive effects on cycle performance of the Si electrodes. Furthermore, the Si electrodes achieved good cycleability up to 500 cycles owing to synergy effects of the Nafion ® coating and an SEI-forming additive of fluoroethylene carbonate (FEC).
- Open Access
- 5 June 2020
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 1 (4) , 625-631
Lithium-ion battery performance enhanced by the combination of Si thin flake anodes and binary ionic liquid systems
The use of ionic liquid (IL)-based electrolytes is one of the methods for solving various problems that pertain to the large-capacity anodes, such as Si and Li, for next-generation lithium ion batteries (LIBs). There is insufficient information about the combinations of such anodes and the IL electrolytes. In the present study, Si thin flake, which is one of the promising Si anode active materials, and binary IL electrolytes, 83.3–16.7 mol% 1-ethyl-3-methylimidazolium bis((fluorosulfonyl)amide)) ([C2mim][FSA])–lithium bis(trifluoromethanesulfonyl)amide (Li[TFSA]), 83.3–16.7 mol% [C2mim][FSA]–lithium bis((fluorosulfonyl)amide)) (Li[FSA]), and 50.0–50.0 mol% [C2mim][FSA]–Li[FSA], were used for collecting various information on the battery performance, morphology variation of the Si thin flake, and chemical species in the solid electrolyte interface (SEI) layer. Operando scanning electron microscopy (SEM) and ex-situ X-ray photoelectron spectroscopy (XPS) revealed that the SEI layer composition depends on the Li salt species and that their molar fractions in the binary IL electrolytes strongly affect the morphology variation in the Si thin flakes during the charge process. When the favorable Li conductive components, e.g., LiF and Li3N, were abundantly contained in the SEI layer, the charge and discharge behavior of the Si thin flake anode was greatly improved. The best battery performance was obtained by the combination of the Si thin flake composite anode and the 50.0–50.0 mol% [C2mim][FSA]–Li[FSA]. Discharge capacity above 1100 mAh g−1 was achieved even after 500 cycles under the charge and discharge condition at 3 C rate.
- 5 June 2020
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 1 (4) , 625-631
Open AccessLithium-ion battery performance enhanced by the combination of Si thin flake anodes and binary ionic liquid systems
The use of ionic liquid (IL)-based electrolytes is one of the methods for solving various problems that pertain to the large-capacity anodes, such as Si and Li, for next-generation lithium ion batteries (LIBs). There is insufficient information about the combinations of such anodes and the IL electrolytes. In the present study, Si thin flake, which is one of the promising Si anode active materials, and binary IL electrolytes, 83.3–16.7 mol% 1-ethyl-3-methylimidazolium bis((fluorosulfonyl)amide)) ([C2mim][FSA])–lithium bis(trifluoromethanesulfonyl)amide (Li[TFSA]), 83.3–16.7 mol% [C2mim][FSA]–lithium bis((fluorosulfonyl)amide)) (Li[FSA]), and 50.0–50.0 mol% [C2mim][FSA]–Li[FSA], were used for collecting various information on the battery performance, morphology variation of the Si thin flake, and chemical species in the solid electrolyte interface (SEI) layer. Operando scanning electron microscopy (SEM) and ex-situ X-ray photoelectron spectroscopy (XPS) revealed that the SEI layer composition depends on the Li salt species and that their molar fractions in the binary IL electrolytes strongly affect the morphology variation in the Si thin flakes during the charge process. When the favorable Li conductive components, e.g., LiF and Li3N, were abundantly contained in the SEI layer, the charge and discharge behavior of the Si thin flake anode was greatly improved. The best battery performance was obtained by the combination of the Si thin flake composite anode and the 50.0–50.0 mol% [C2mim][FSA]–Li[FSA]. Discharge capacity above 1100 mAh g−1 was achieved even after 500 cycles under the charge and discharge condition at 3 C rate.
- 3 January 2020
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 167 (4) , 040508
Dilution Effects of Highly Concentrated LiBF 4 /DMC with Fluorinated Esters on Charge/Dishcharge Properties of Ni-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 Positive Electrode
Dilution effects of highly concentrated LiBF 4 /dimethylcarbonate (DMC) electrolyte with three kinds of methyl fluoropropionates, methyl 3,3,3-trifluoropropionate (CF 3 CH 2 COOCH 3 , 3FMP), methyl tetrafluoropropionate (CF 3 CHFCOOCH 3 , 4FMP), and methyl perfluoropropionate (CF 3 CF 2 COOCH 3 , 5FMP) on the charge/discharge characteristics of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) positive electrode. All the electrolytes had viscosities lower than 10 mPa s, which are affordable for practical use. In nearly saturated 1.8 mol kg −1 LiBF 4 /DMC + 4FMP, NCM811 exhibited good cycling performance, whereas severe capacity fading was observed in 1.0 mol kg −1 LiBF 4 /DMC + 5FMP and 3.3 mol kg −1 LiBF 4 /DMC + 3FMP even though they also nearly saturated. Raman spectra revealed that the dilution with 5FMP formed a large amount of free DMC molecules that are vulnerable to oxidation in LiBF 4 /DMC + 5FMP. In contrast, the 3FMP diluent in LiBF 4 /DMC + 3FMP is less stable against oxidation than the other two diluents because the number of electron-withdrawing F atoms is smaller. The miscibility of 4FMP with concentrated LiBF 4 /DMC is higher than 5FMP, and the higher concentration (1.8 mol kg −1 ) suppressed the formation of free DMC molecules. On the other hand, the oxidation resistance of 4FMP is higher than 3FMP. As a compromise, LiBF 4 /DMC + 4FMP showed the best performance.
- 3 January 2020
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 167 (4) , 040508
Dilution Effects of Highly Concentrated LiBF 4 /DMC with Fluorinated Esters on Charge/Dishcharge Properties of Ni-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 Positive Electrode
Dilution effects of highly concentrated LiBF 4 /dimethylcarbonate (DMC) electrolyte with three kinds of methyl fluoropropionates, methyl 3,3,3-trifluoropropionate (CF 3 CH 2 COOCH 3 , 3FMP), methyl tetrafluoropropionate (CF 3 CHFCOOCH 3 , 4FMP), and methyl perfluoropropionate (CF 3 CF 2 COOCH 3 , 5FMP) on the charge/discharge characteristics of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) positive electrode. All the electrolytes had viscosities lower than 10 mPa s, which are affordable for practical use. In nearly saturated 1.8 mol kg −1 LiBF 4 /DMC + 4FMP, NCM811 exhibited good cycling performance, whereas severe capacity fading was observed in 1.0 mol kg −1 LiBF 4 /DMC + 5FMP and 3.3 mol kg −1 LiBF 4 /DMC + 3FMP even though they also nearly saturated. Raman spectra revealed that the dilution with 5FMP formed a large amount of free DMC molecules that are vulnerable to oxidation in LiBF 4 /DMC + 5FMP. In contrast, the 3FMP diluent in LiBF 4 /DMC + 3FMP is less stable against oxidation than the other two diluents because the number of electron-withdrawing F atoms is smaller. The miscibility of 4FMP with concentrated LiBF 4 /DMC is higher than 5FMP, and the higher concentration (1.8 mol kg −1 ) suppressed the formation of free DMC molecules. On the other hand, the oxidation resistance of 4FMP is higher than 3FMP. As a compromise, LiBF 4 /DMC + 4FMP showed the best performance.
- 2 December 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (16) , A4005-A4013
Dilution Effects of Highly Concentrated Dimethyl Carbonate-Based Electrolytes with a Hydrofluoroether on Charge/Discharge Properties of LiNi0.8Co0.1Mn0.1O2 Positive Electrode
In highly concentrated LiBF4/dimethyl carbonate (DMC) electrolyte, Ni-rich LiNi0.8Co0.1Mn0.1O2 (NCM811) positive-electrode exhibited a good cycle performance and the crack formation in NCM811 particles was remarkably suppressed. However, the high concentration causes some problems, such as a high viscosity, a low ionic conductivity and a high cost. To solve these problems, we chose 1,1,2,2–tetrafluoroethyl 2,2,3,3–tetrafluoropropyl ether (HFE) to dilute the concentrated LiBF4/ and LiPF6/DMC systems. The cycle performance of NCM811 electrode remarkably deteriorated in 0.96 mol kg−1 LiBF4/DMC+HFE (1:2 by volume). Raman spectra indicated that the fraction of free DMC increased in the diluted electrolyte, which led to instability against oxidation. However, in the LiPF6/DMC system, the fraction of free DMC had rarely increased after diluted with HFE. The diluted electrolyte showed a high stability against oxidation comparable to the nearly saturated electrolyte, and the NCM811 electrode showed an excellent cycle performance.
- 2 December 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (16) , A4005-A4013
Dilution Effects of Highly Concentrated Dimethyl Carbonate-Based Electrolytes with a Hydrofluoroether on Charge/Discharge Properties of LiNi0.8Co0.1Mn0.1O2 Positive Electrode
In highly concentrated LiBF4/dimethyl carbonate (DMC) electrolyte, Ni-rich LiNi0.8Co0.1Mn0.1O2 (NCM811) positive-electrode exhibited a good cycle performance and the crack formation in NCM811 particles was remarkably suppressed. However, the high concentration causes some problems, such as a high viscosity, a low ionic conductivity and a high cost. To solve these problems, we chose 1,1,2,2–tetrafluoroethyl 2,2,3,3–tetrafluoropropyl ether (HFE) to dilute the concentrated LiBF4/ and LiPF6/DMC systems. The cycle performance of NCM811 electrode remarkably deteriorated in 0.96 mol kg−1 LiBF4/DMC+HFE (1:2 by volume). Raman spectra indicated that the fraction of free DMC increased in the diluted electrolyte, which led to instability against oxidation. However, in the LiPF6/DMC system, the fraction of free DMC had rarely increased after diluted with HFE. The diluted electrolyte showed a high stability against oxidation comparable to the nearly saturated electrolyte, and the NCM811 electrode showed an excellent cycle performance.
- 28 October 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 2 (11) , 7728-7732
Extension of Anodic Potential Window of Ester-Based Electrolyte Solutions for High-Voltage Lithium Ion Batteries
- 28 October 2019
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 2 (11) , 7728-7732
Extension of Anodic Potential Window of Ester-Based Electrolyte Solutions for High-Voltage Lithium Ion Batteries
- 7 October 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (43) , 39910-39920
Effect of Lithium Silicate Addition on the Microstructure and Crack Formation of LiNi0.8Co0.1Mn0.1O2 Cathode Particles
The microstructure of LiNi0.8Co0.1Mn0.1O2 cathode materials was controlled by the addition of lithium silicate, and the influence on the cycle performance and the rate-capability was investigated. Si was not included within the lattice, but localized at the grain boundaries of the primary particles and the pores inside the secondary particles. The addition of the lithium silicate greatly decreased the density of the pores between the primary particles and improved the density of the secondary particles. The capacity retention was successfully improved for lithium silicate-added LiNi0.8Co0.1Mn0.1O2. When lithium silicate-free LiNi0.8Co0.1Mn0.1O2 was charged to 4.3 V, many cracks were formed along the grain boundaries even in the first cycle, while crack formation was remarkably inhibited for lithium silicate-added LiNi0.8Co0.1Mn0.1O2. Moreover, lithium silicate-added LiNi0.8Co0.1Mn0.1O2 particles were almost free from visible microcracks even after 100 cycles at the discharged state. These results suggest that the lithium silicate reinforces the grain-adhesion at the grain boundaries, inhibiting crack formation and electrolyte decomposition inside the cracks.
- 7 October 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (43) , 39910-39920
Effect of Lithium Silicate Addition on the Microstructure and Crack Formation of LiNi0.8Co0.1Mn0.1O2 Cathode Particles
The microstructure of LiNi0.8Co0.1Mn0.1O2 cathode materials was controlled by the addition of lithium silicate, and the influence on the cycle performance and the rate-capability was investigated. Si was not included within the lattice, but localized at the grain boundaries of the primary particles and the pores inside the secondary particles. The addition of the lithium silicate greatly decreased the density of the pores between the primary particles and improved the density of the secondary particles. The capacity retention was successfully improved for lithium silicate-added LiNi0.8Co0.1Mn0.1O2. When lithium silicate-free LiNi0.8Co0.1Mn0.1O2 was charged to 4.3 V, many cracks were formed along the grain boundaries even in the first cycle, while crack formation was remarkably inhibited for lithium silicate-added LiNi0.8Co0.1Mn0.1O2. Moreover, lithium silicate-added LiNi0.8Co0.1Mn0.1O2 particles were almost free from visible microcracks even after 100 cycles at the discharged state. These results suggest that the lithium silicate reinforces the grain-adhesion at the grain boundaries, inhibiting crack formation and electrolyte decomposition inside the cracks.
- 6 August 2019
- Published by Wiley in ChemistrySelect
- Vol. 4 (29) , 8676-8681
Improvement of Cycleability and Rate‐Capability of LiNi 0.5 Co 0.2 Mn 0.3 O 2 Cathode Materials Coated with Lithium Boron Oxide by an Antisolvent Precipitation Method
LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM) particles coated with lithium boron oxide were prepared by an antisolvent precipitation method. In the antisolvent precipitation method, ethanol was used to strip off the hydrated water coordinated with lithium ions and borate ions. By the antisolvent precipitation method, the NCM particles were coated with a uniform layer of LiBO 2 . The capacity fading on cycling was successfully suppressed for the lithium boron oxide‐coated samples. In addition, the rate capability was also improved by the coating. The lithium boron oxide coating effectively suppressed the increase of the electrode impedance associated with the electrolyte decomposition. Crack formation in the secondary particles after charge‐discharge cycling was greatly inhibited for lithium boron oxide‐coated NCM. It was demonstrated that the lithium boron oxide coating layer suppressed the side reactions not only on the particle surface, but also in the intergranular cracks by inhibiting the penetration of the electrolyte solution.
- 6 August 2019
- Published by Wiley in ChemistrySelect
- Vol. 4 (29) , 8676-8681
Improvement of Cycleability and Rate‐Capability of LiNi 0.5 Co 0.2 Mn 0.3 O 2 Cathode Materials Coated with Lithium Boron Oxide by an Antisolvent Precipitation Method
LiNi 0.5 Co 0.2 Mn 0.3 O 2 (NCM) particles coated with lithium boron oxide were prepared by an antisolvent precipitation method. In the antisolvent precipitation method, ethanol was used to strip off the hydrated water coordinated with lithium ions and borate ions. By the antisolvent precipitation method, the NCM particles were coated with a uniform layer of LiBO 2 . The capacity fading on cycling was successfully suppressed for the lithium boron oxide‐coated samples. In addition, the rate capability was also improved by the coating. The lithium boron oxide coating effectively suppressed the increase of the electrode impedance associated with the electrolyte decomposition. Crack formation in the secondary particles after charge‐discharge cycling was greatly inhibited for lithium boron oxide‐coated NCM. It was demonstrated that the lithium boron oxide coating layer suppressed the side reactions not only on the particle surface, but also in the intergranular cracks by inhibiting the penetration of the electrolyte solution.
- 20 March 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (6) , A941-A943
Communication—Enhancement of Structural Stability of LiNi0.5Co0.2Mn0.3O2 Cathode Particles against High-Voltage Cycling by Lithium Silicate Addition
Lithium silicate was incorporated within Ni0.5Co0.2Mn0.3(OH)2 precursor particles via an anti-solvent precipitation method to prepare lithium silicate-added LiNi0.5Co0.2Mn0.3O2 (NCM) particles. Lithium silicate was found at the grain boundaries in the NCM secondary particles, which significantly improved the capacity retention in high voltage operation (3.0–4.6 V). Cross-sectional SEM images revealed that cracks were seriously formed inside the lithium silicate-free NCM particles after cycling, while crack formation was remarkably inhibited for lithium silicate-added NCM. These results suggested that lithium silicate at the grain boundaries strengthened the interfacial-adhesion between primary particles, resulting in the improved cycling stability.
- 20 March 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (6) , A941-A943
Communication—Enhancement of Structural Stability of LiNi0.5Co0.2Mn0.3O2 Cathode Particles against High-Voltage Cycling by Lithium Silicate Addition
Lithium silicate was incorporated within Ni0.5Co0.2Mn0.3(OH)2 precursor particles via an anti-solvent precipitation method to prepare lithium silicate-added LiNi0.5Co0.2Mn0.3O2 (NCM) particles. Lithium silicate was found at the grain boundaries in the NCM secondary particles, which significantly improved the capacity retention in high voltage operation (3.0–4.6 V). Cross-sectional SEM images revealed that cracks were seriously formed inside the lithium silicate-free NCM particles after cycling, while crack formation was remarkably inhibited for lithium silicate-added NCM. These results suggested that lithium silicate at the grain boundaries strengthened the interfacial-adhesion between primary particles, resulting in the improved cycling stability.
- 25 January 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (2) , A258-A263
Oxygen-Content Dependence of Cycle Performance and Morphology Changes in Amorphous-SiOx Thin-Film Negative Electrodes for Lithium-Ion Batteries
The silicon–oxygen binary system (SiOx) is a promising candidate as a negative electrode for next-generation lithium-ion batteries. Thin SiOx films of different oxygen contents were prepared by magnetron sputtering. Although almost all Si atoms in SiOx at low oxygen contents (x = 0.21 and 0.48) contributed to the reversible alloying/dealloying reactions, an irreversible fraction of Si in SiOx at high oxygen contents (x = 1.09 and 1.78) increased owing to the formation of Li4SiO4. In return for the decrease of reversible capacity, the capacity retention of heavily O-doped SiOx films improved owing to the buffer effect of Li4SiO4 matrix against volume changes. The addition of vinylene carbonate (VC) to the electrolyte further improved the cyclability of the SiOx films, especially those of higher oxygen contents. For the pure-Si film, a sponge-like porous structure appeared after cycling owing to repeated crack formation and inhomogeneous volume changes, and resulted in massive electrode swelling. The morphology change with cycling was suppressed by the presence of Li4SiO4 matrix and a homogeneous solid electrolyte interphase derived from VC, resulting in a superior cycle performance of the heavily O-doped SiOx negative electrodes.
- 25 January 2019
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 166 (2) , A258-A263
Oxygen-Content Dependence of Cycle Performance and Morphology Changes in Amorphous-SiOx Thin-Film Negative Electrodes for Lithium-Ion Batteries
The silicon–oxygen binary system (SiOx) is a promising candidate as a negative electrode for next-generation lithium-ion batteries. Thin SiOx films of different oxygen contents were prepared by magnetron sputtering. Although almost all Si atoms in SiOx at low oxygen contents (x = 0.21 and 0.48) contributed to the reversible alloying/dealloying reactions, an irreversible fraction of Si in SiOx at high oxygen contents (x = 1.09 and 1.78) increased owing to the formation of Li4SiO4. In return for the decrease of reversible capacity, the capacity retention of heavily O-doped SiOx films improved owing to the buffer effect of Li4SiO4 matrix against volume changes. The addition of vinylene carbonate (VC) to the electrolyte further improved the cyclability of the SiOx films, especially those of higher oxygen contents. For the pure-Si film, a sponge-like porous structure appeared after cycling owing to repeated crack formation and inhomogeneous volume changes, and resulted in massive electrode swelling. The morphology change with cycling was suppressed by the presence of Li4SiO4 matrix and a homogeneous solid electrolyte interphase derived from VC, resulting in a superior cycle performance of the heavily O-doped SiOx negative electrodes.