Rani Warsi Sullivan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rani Warsi Sullivan has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Shuvam Saha
Mississippi State University, Mississippi State, Mississippi 39762
8 shared publications Daniel A. Drake
3 shared publicationsJutima Simsiriwong
Department of Mechanical Engineering, Auburn University, Auburn, AL, USA
3 shared publicationsMyles L. Baker
3 shared publicationsDaniel A Drake
Department of Aerospace Engineering, Mississippi State University, Starkville, MS, USA
2 shared publications- Daniel A. Drake
Department of Aerospace Engineering, Mississippi State University, Mississippi State, USA
2 shared publications
Latest Publications
- 1 January 2026
- Published by American Association for the Advancement of Science (AAAS) in Research
- Vol. 9
Laser Vibrometry and Dispersion Analysis-Enabled Mechanical Property Characterization for Additively Manufactured Thermoset Composites
Large-format additive manufacturing of thermoset composites enables rapid fabrication of large structures, but nondestructive characterization of their print-path-dependent mechanical behavior remains difficult. Existing qualification routes rely mainly on destructive coupon testing or defect-oriented nondestructive evaluation and therefore provide limited capability for targeted mapping of direction-dependent mechanical variability. This study presents a piezoelectric transducer–laser Doppler vibrometry framework for direction-conditioned dispersion inversion of full-field guided wave measurements in additively manufactured thermoset composites. The method decomposes the frequency–wavenumber spectrum by propagation angle and independently fits the extracted dispersion data in each propagation direction to obtain scan-region-specific effective shear-wave velocity, an effective Poisson’s-ratio parameter, and effective-modulus responses as functions of propagation direction. Benchmark testing on an isotropic aluminum plate validates that the workflow recovers isotropic guided wave behavior without introducing artificial angular bias. Applied to a chopped-carbon-fiber thermoset composite, the framework reveals print-path-dependent anisotropic wave propagation through elliptical wavefields and frequency–wavenumber spectra. The resulting effective stiffness estimates reproduce the direction-dependent stiffness variation and approximate magnitude observed in conventional tensile measurements, supporting the mechanical relevance of the guided wave-derived response. By converting full-field guided wave measurements into scan-region-specific, direction-resolved effective-stiffness estimates, this work provides a practical nondestructive route to support quality control, process validation, and structural evaluation of aerospace composite tooling manufactured by large-format thermoset additive manufacturing.
- 1 January 2026
- Published by American Association for the Advancement of Science (AAAS) in Research
- Vol. 9
Laser Vibrometry and Dispersion Analysis-Enabled Mechanical Property Characterization for Additively Manufactured Thermoset Composites
Large-format additive manufacturing of thermoset composites enables rapid fabrication of large structures, but nondestructive characterization of their print-path-dependent mechanical behavior remains difficult. Existing qualification routes rely mainly on destructive coupon testing or defect-oriented nondestructive evaluation and therefore provide limited capability for targeted mapping of direction-dependent mechanical variability. This study presents a piezoelectric transducer–laser Doppler vibrometry framework for direction-conditioned dispersion inversion of full-field guided wave measurements in additively manufactured thermoset composites. The method decomposes the frequency–wavenumber spectrum by propagation angle and independently fits the extracted dispersion data in each propagation direction to obtain scan-region-specific effective shear-wave velocity, an effective Poisson’s-ratio parameter, and effective-modulus responses as functions of propagation direction. Benchmark testing on an isotropic aluminum plate validates that the workflow recovers isotropic guided wave behavior without introducing artificial angular bias. Applied to a chopped-carbon-fiber thermoset composite, the framework reveals print-path-dependent anisotropic wave propagation through elliptical wavefields and frequency–wavenumber spectra. The resulting effective stiffness estimates reproduce the direction-dependent stiffness variation and approximate magnitude observed in conventional tensile measurements, supporting the mechanical relevance of the guided wave-derived response. By converting full-field guided wave measurements into scan-region-specific, direction-resolved effective-stiffness estimates, this work provides a practical nondestructive route to support quality control, process validation, and structural evaluation of aerospace composite tooling manufactured by large-format thermoset additive manufacturing.
- 14 March 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 299
Manufacturing a 3D stitched highly unitized PRSEUS-based conformal propellant tank: Lessons learned
- 14 March 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 299
Manufacturing a 3D stitched highly unitized PRSEUS-based conformal propellant tank: Lessons learned
- 22 October 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 288
Pull-off Behavior of Stitched Composite T-Joints
- 22 October 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 288
Pull-off Behavior of Stitched Composite T-Joints
- 1 September 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 61 (5) , 1475-1481
Influence of Stitch Angle on the Flexural Response of Composite Structures
Utilizing lightweight composites in aerospace vehicles plays a pivotal role in sustainability by improving fuel efficiency and mitigating emissions. However, due to their low interlaminar strength, delaminations and microcracking degrade their strength and stiffness properties. Through-thickness stitching improves the interlaminar strength, thus increasing the delamination tolerance of composite structures. Therefore, in this study, the influence of repeated periodic stitching patterns, stitched at three different angles (0, 45, and 90°) w.r.t. the transverse direction, on the flexural properties of stitched composites is investigated. The strain distributions of these specimens were obtained using a single continuous optical fiber bonded to the tensile surface of the specimens. The results show that stitching at a 45° angle produced lower strains and higher flexural strength and bending modulus when compared to the stitched and unstitched laminates. An increase of 32.3 and 47.4% in the flexural strength and bending modulus were obtained, respectively, with reference to the unstitched laminates. The failure morphology of specimens was also analyzed using optical microscopy and revealed that the stitch seams arrested delaminations. However, due to the 45° angle, the damage progressed along a longer distance, thus resulting in an increased ultimate failure load.
- 1 September 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 61 (5) , 1475-1481
Influence of Stitch Angle on the Flexural Response of Composite Structures
Utilizing lightweight composites in aerospace vehicles plays a pivotal role in sustainability by improving fuel efficiency and mitigating emissions. However, due to their low interlaminar strength, delaminations and microcracking degrade their strength and stiffness properties. Through-thickness stitching improves the interlaminar strength, thus increasing the delamination tolerance of composite structures. Therefore, in this study, the influence of repeated periodic stitching patterns, stitched at three different angles (0, 45, and 90°) w.r.t. the transverse direction, on the flexural properties of stitched composites is investigated. The strain distributions of these specimens were obtained using a single continuous optical fiber bonded to the tensile surface of the specimens. The results show that stitching at a 45° angle produced lower strains and higher flexural strength and bending modulus when compared to the stitched and unstitched laminates. An increase of 32.3 and 47.4% in the flexural strength and bending modulus were obtained, respectively, with reference to the unstitched laminates. The failure morphology of specimens was also analyzed using optical microscopy and revealed that the stitch seams arrested delaminations. However, due to the 45° angle, the damage progressed along a longer distance, thus resulting in an increased ultimate failure load.
- 27 January 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (6) , 827-847
A review on gas permeability of polymer matrix composites for cryogenic applications
Fiber-reinforced polymer matrix composites are increasingly considered for lightweight cryogenic pressure vessels due to their excellent combination of tailorability, specific mechanical properties, and relatively low coefficients of thermal expansion. However, significant challenges must be overcome to fully utilize PMCs for cryogenic fuel tanks in terms of transverse microcracking and subsequent permeation of cryogenic fuel. Gas permeation and microcrack densities of cryogenically cycled composites are highly influenced by their layup, ply thickness, load case, and manufacturing defects like voids and resin rich zones. There has been a significant amount of research on measuring gas permeation of composites fatigued under pure thermal or uniaxial thermo-mechanical stresses. However, results demonstrate that the gas permeability should be measured under biaxial thermo-mechanical stresses to properly gauge the leakage characteristics of damaged composites. This paper summarizes the results from over a hundred papers on the key parameters that influence the gas permeability of composites, appropriate testing methods to cycle composites for permeability measurement, methods to limit the evolution of transverse microcracks, and materials traditionally used for the fabrication of all-composite cryogenic fuel tanks. Thin plies and nanofiller-toughening of the matrix have been shown to provide significant improvements in transverse microcrack suppression within cryogenically cycled composites.
- 27 January 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (6) , 827-847
A review on gas permeability of polymer matrix composites for cryogenic applications
Fiber-reinforced polymer matrix composites are increasingly considered for lightweight cryogenic pressure vessels due to their excellent combination of tailorability, specific mechanical properties, and relatively low coefficients of thermal expansion. However, significant challenges must be overcome to fully utilize PMCs for cryogenic fuel tanks in terms of transverse microcracking and subsequent permeation of cryogenic fuel. Gas permeation and microcrack densities of cryogenically cycled composites are highly influenced by their layup, ply thickness, load case, and manufacturing defects like voids and resin rich zones. There has been a significant amount of research on measuring gas permeation of composites fatigued under pure thermal or uniaxial thermo-mechanical stresses. However, results demonstrate that the gas permeability should be measured under biaxial thermo-mechanical stresses to properly gauge the leakage characteristics of damaged composites. This paper summarizes the results from over a hundred papers on the key parameters that influence the gas permeability of composites, appropriate testing methods to cycle composites for permeability measurement, methods to limit the evolution of transverse microcracks, and materials traditionally used for the fabrication of all-composite cryogenic fuel tanks. Thin plies and nanofiller-toughening of the matrix have been shown to provide significant improvements in transverse microcrack suppression within cryogenically cycled composites.
- 1 January 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 61 (1) , 222-228
Stitched Graphene Nanoplatelet Composites for Unitized Aerospace Structures
Lightweight composites play an important role in sustainability as their usage in aerospace vehicles translates to improved fuel consumption and reduced emissions. However, due to their low interlaminar strength, delaminations and microcracking degrade their strength and stiffness properties. Through-thickness stitching in composites enhances interlaminar properties but reduces the in-plane properties. Graphene nanoplatelets (GNPs) and carbon “thin plies” have been found to increase the mechanical properties of these composite structures. This study considers a hybrid composite that uses GNPs coupled with thin plies at the midplane to mitigate the reduction in the in-plane properties. Composite specimens [ ] were stitched with two different seam angles (0 and 90°) and tested under uniaxial tensile loading. Surface strain fields from digital image correlation measurements show a significant decrease in strain concentrations in the hybrid specimens compared to the baseline stitched composites. An increase of 17% in tensile modulus and a reduction of 15% in strain energy density are realized due to the hybrid architecture of the stitched composite.
- 1 January 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 61 (1) , 222-228
Stitched Graphene Nanoplatelet Composites for Unitized Aerospace Structures
Lightweight composites play an important role in sustainability as their usage in aerospace vehicles translates to improved fuel consumption and reduced emissions. However, due to their low interlaminar strength, delaminations and microcracking degrade their strength and stiffness properties. Through-thickness stitching in composites enhances interlaminar properties but reduces the in-plane properties. Graphene nanoplatelets (GNPs) and carbon “thin plies” have been found to increase the mechanical properties of these composite structures. This study considers a hybrid composite that uses GNPs coupled with thin plies at the midplane to mitigate the reduction in the in-plane properties. Composite specimens [ ] were stitched with two different seam angles (0 and 90°) and tested under uniaxial tensile loading. Surface strain fields from digital image correlation measurements show a significant decrease in strain concentrations in the hybrid specimens compared to the baseline stitched composites. An increase of 17% in tensile modulus and a reduction of 15% in strain energy density are realized due to the hybrid architecture of the stitched composite.
- 1 November 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 60 (6) , 1846-1853
Gas Permeability and Flexural Strength of Impacted Composites for Cryogenic Propellant Tanks
Reusable composite cryogenic tanks may be used in next-generation space launch systems due to their several benefits, such as increased specific strength, tailorability, and low coefficient of thermal expansion. However, transverse microcracks within composites due to thermal stresses and barely visible impact damage can cause cryogenic fuel to leak through the walls of the tank. The objective of the present study is to evaluate the gas permeability of impacted and thermally cycled composites and correlate it to their postimpact residual strength. Cross-ply carbon/epoxy composites ([ ]) fabricated from unidirectional prepregs were subjected to 20 cryogenic cycles from ambient to cryogenic temperatures ([ ]). Barely visible impact damage at two different impact velocities ([ ] and [ ]) was imparted to the specimens at room and cryogenic temperatures before and after cryogenic cycling. The composites’ gas permeability, residual flexural strength, and absorbed energy were measured and correlated. Composite specimens subjected to impact at room temperature had higher gas permeability and absorbed energy with lower residual flexural strength. A linear relationship was observed between gas permeability, absorbed energy, and postimpact flexural strength. Two linear models to predict gas permeability with absorbed energy and flexural strength as variables have been presented for impacted and cryogenically cycled specimens with an [ ] value of at least 96%.
- 1 November 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 60 (6) , 1846-1853
Gas Permeability and Flexural Strength of Impacted Composites for Cryogenic Propellant Tanks
Reusable composite cryogenic tanks may be used in next-generation space launch systems due to their several benefits, such as increased specific strength, tailorability, and low coefficient of thermal expansion. However, transverse microcracks within composites due to thermal stresses and barely visible impact damage can cause cryogenic fuel to leak through the walls of the tank. The objective of the present study is to evaluate the gas permeability of impacted and thermally cycled composites and correlate it to their postimpact residual strength. Cross-ply carbon/epoxy composites ([ ]) fabricated from unidirectional prepregs were subjected to 20 cryogenic cycles from ambient to cryogenic temperatures ([ ]). Barely visible impact damage at two different impact velocities ([ ] and [ ]) was imparted to the specimens at room and cryogenic temperatures before and after cryogenic cycling. The composites’ gas permeability, residual flexural strength, and absorbed energy were measured and correlated. Composite specimens subjected to impact at room temperature had higher gas permeability and absorbed energy with lower residual flexural strength. A linear relationship was observed between gas permeability, absorbed energy, and postimpact flexural strength. Two linear models to predict gas permeability with absorbed energy and flexural strength as variables have been presented for impacted and cryogenically cycled specimens with an [ ] value of at least 96%.
- 13 October 2022
- Published by Elsevier in Composite Structures
- Vol. 304
Gas permeability mitigation of cryogenically cycled stitched composites using thin plies
- 13 October 2022
- Published by Elsevier in Composite Structures
- Vol. 304
Gas permeability mitigation of cryogenically cycled stitched composites using thin plies