Борис Злотенко
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Борис Злотенко has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Олексій Воляник
4 shared publications- Марк Залюбовський
Київський національний університет технологій та дизайну
3 shared publications - Oleg Synyuk
Khmelnytskyi National University
2 shared publications - Volodymyr Osypenko
Kyiv National University of Technologies and Design
2 shared publications - Геннадій Мельник
Kyiv National University of Technologies and Design, Kyiv, Ukraine
2 shared publications Д. В. Стаценко
Київський національний університет технологій та дизайну
2 shared publications
Latest Publications
- Open Access
- 29 January 2026
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 361 (1) , 291-297
КОНСТРУЮВАННЯ ТА ДОСЛІДЖЕННЯ ПРИВОДУ ІЗ ВИКОРИСТАННЯМ КАРДАННОЇ ПЕРЕДАЧІ ДЛЯ ГАЛТУВАЛЬНОГО ОБЛАДНАННЯ
The article addresses the issue of improving the drive of a “Turbula”-type tumbling machine with a working chamber that performs a complex spatial motion. Experimental studies were conducted on the movement of the processing media inside the chamber of the “Turbula”-type tumbling machine, in which the driven shaft rotates with a non-uniform angular velocity. It was found that such a processing mode results in non-uniform intensity of media movement between the opposite ends of the chamber in opposing directions, which prevents uniform surface treatment of parts and significantly limits the technological capabilities of the machine. Based on analytical studies, a rational dependence of the driving shaft’s angular velocity variation was formulated, wherein the peak values of the angular velocities of the driving and driven shafts are in antiphase and have equal amplitude values. This enables uniform intensity of media movement between the opposite ends of the working chamber in opposing directions. Implementation of the proposed angular velocity law ensures a stable and symmetric treatment mode throughout the entire processing cycle. Using the obtained expressions and SolidWorks-2016 CAD system, a 3D model was developed and a parametric calculation of the drive system, including a cardan transmission, was carried out. The necessity of maintaining a specific angle between the axes of the cardan mechanism shafts and spatial positioning of the drive elements—such that the axes of its key joints lie in the same plane—was substantiated. A drive design was developed that is capable of realizing the specified angular velocity law. The results can be applied in the development of new or modernization of existing tumbling machines with improved operational efficiency. These findings can be effectively used at the design stage by engineering departments of machine-building enterprises.
- 29 January 2026
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 361 (1) , 291-297
Open AccessКОНСТРУЮВАННЯ ТА ДОСЛІДЖЕННЯ ПРИВОДУ ІЗ ВИКОРИСТАННЯМ КАРДАННОЇ ПЕРЕДАЧІ ДЛЯ ГАЛТУВАЛЬНОГО ОБЛАДНАННЯ
The article addresses the issue of improving the drive of a “Turbula”-type tumbling machine with a working chamber that performs a complex spatial motion. Experimental studies were conducted on the movement of the processing media inside the chamber of the “Turbula”-type tumbling machine, in which the driven shaft rotates with a non-uniform angular velocity. It was found that such a processing mode results in non-uniform intensity of media movement between the opposite ends of the chamber in opposing directions, which prevents uniform surface treatment of parts and significantly limits the technological capabilities of the machine. Based on analytical studies, a rational dependence of the driving shaft’s angular velocity variation was formulated, wherein the peak values of the angular velocities of the driving and driven shafts are in antiphase and have equal amplitude values. This enables uniform intensity of media movement between the opposite ends of the working chamber in opposing directions. Implementation of the proposed angular velocity law ensures a stable and symmetric treatment mode throughout the entire processing cycle. Using the obtained expressions and SolidWorks-2016 CAD system, a 3D model was developed and a parametric calculation of the drive system, including a cardan transmission, was carried out. The necessity of maintaining a specific angle between the axes of the cardan mechanism shafts and spatial positioning of the drive elements—such that the axes of its key joints lie in the same plane—was substantiated. A drive design was developed that is capable of realizing the specified angular velocity law. The results can be applied in the development of new or modernization of existing tumbling machines with improved operational efficiency. These findings can be effectively used at the design stage by engineering departments of machine-building enterprises.
- Open Access
- 30 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (138)) , 16-22
Revealing the influence of 3D printing density on the physical and mechanical properties of polymer articles
This study investigates the process of 3D printing of polymer articles in light industry. The task addressed is to determine the stressed-strained state of 3D-printed articles made of PETG polymer, taking into account the nonlinear (inelastic) physical and mechanical properties of the material and the influence of printing density on its mechanical behavior. The study’s result established that the tensile curve of 3D-printed samples from PETG follows the form of power function that reflects the properties of an inelastic polymer material. Applying the resulting power function relationship between deformations and stress, unlike the linear one, has made it possible to determine the normal stresses that appear in the internal layers of 3D-printed articles in the form of a beam of rectangular cross-section at bending. Numerical values were derived for parameters of the power function that reflects the dependence of stresses on strain when stretching 3D-printed samples from PETG, manufactured at a print density of 70%, 80%, 90%, and 100%. It was found that with an increase in the density of PETG 3D printing from 60% to 100%, the tensile stresses in the samples increase from 12.3 to 19.6 MPa, while the relative deformation at their rupture decreases from 0.076 to 0.062. The resulting dependences make it possible to determine the required density of 3D printing to ensure the predefined limit load parameters for articles during their application. Taking into account the nonlinear nature of deformation and the influence of the density of the structure on tensile stresses and relative deformation at the rupture of the polymer material creates opportunities for designing and manufacturing 3D-printed articles in light industry with predictable properties to enable their operability under operational loads.
- 30 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (138)) , 16-22
Open AccessRevealing the influence of 3D printing density on the physical and mechanical properties of polymer articles
This study investigates the process of 3D printing of polymer articles in light industry. The task addressed is to determine the stressed-strained state of 3D-printed articles made of PETG polymer, taking into account the nonlinear (inelastic) physical and mechanical properties of the material and the influence of printing density on its mechanical behavior. The study’s result established that the tensile curve of 3D-printed samples from PETG follows the form of power function that reflects the properties of an inelastic polymer material. Applying the resulting power function relationship between deformations and stress, unlike the linear one, has made it possible to determine the normal stresses that appear in the internal layers of 3D-printed articles in the form of a beam of rectangular cross-section at bending. Numerical values were derived for parameters of the power function that reflects the dependence of stresses on strain when stretching 3D-printed samples from PETG, manufactured at a print density of 70%, 80%, 90%, and 100%. It was found that with an increase in the density of PETG 3D printing from 60% to 100%, the tensile stresses in the samples increase from 12.3 to 19.6 MPa, while the relative deformation at their rupture decreases from 0.076 to 0.062. The resulting dependences make it possible to determine the required density of 3D printing to ensure the predefined limit load parameters for articles during their application. Taking into account the nonlinear nature of deformation and the influence of the density of the structure on tensile stresses and relative deformation at the rupture of the polymer material creates opportunities for designing and manufacturing 3D-printed articles in light industry with predictable properties to enable their operability under operational loads.
- Open Access
- 11 December 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 359 (6.1) , 187-193
ПОРІВНЯЛЬНИЙ СИЛОВИЙ АНАЛІЗ ГАЛТУВАЛЬНИХ МАШИН НА ОСНОВІ ВИЗНАЧЕННЯ РЕАКЦІЙ У КІНЕМАТИЧНИХ ЗВ’ЯЗКАХ ЇХ ПРОСТОРОВИХ МЕХАНІЗМІВ
Burnishing operations can be performed using various types of equipment; however, the highest efficiency of this process is achieved when machines with work chambers capable of executing complex spatial movements are employed. Depending on the structural design, such machines differ in drive configuration, mechanism kinematics, and technological capabilities, enabling a wide range of operations including grinding, polishing, glazing, surface strengthening, sprue removal, and mixing of heterogeneous components. The structural foundation of these machines typically consists of spatial mechanisms based on rotational kinematic pairs. One of the most important application areas of such machines is the automotive industry, where burnishing is widely used for processing both metal and polymer parts. The process is especially efficient in serial and mass production, where stringent requirements are imposed on surface quality, productivity, and cost-efficiency. Burnishing allows for achieving a high surface finish, removing burrs, rounding edges, improving appearance, and enhancing the operational characteristics of components, which is particularly crucial for automotive assemblies such as transmissions, suspensions, and fasteners. A key condition for the long-term and stable operation of a burnishing machine is the accurate determination of loads in its kinematic pairs. In this study, a three-dimensional CAD model of an eight-link spatial mechanism with dual degrees of mobility was developed, in which the cylindrical chamber follows a complex spatial motion trajectory. Using the “SolidWorks Motion” software package, an analysis was carried out to assess the variation of reaction forces in all rotational joints of the mechanism depending on the geometric parameter δ, which characterizes the center-to-center distance of the chamber. The simulation results revealed the nature of the influence of parameter δ on the peak values of axial and radial reaction forces. It was found that as δ increases up to a certain threshold, a uniform distribution of loads among the kinematic joints is maintained. However, further increase in this parameter leads to localized overloading of specific joints. The obtained results can be applied in the design of burnishing machines for the mechanical engineering and automotive industries to ensure their reliable and energy-efficient operation.
- 11 December 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 359 (6.1) , 187-193
Open AccessПОРІВНЯЛЬНИЙ СИЛОВИЙ АНАЛІЗ ГАЛТУВАЛЬНИХ МАШИН НА ОСНОВІ ВИЗНАЧЕННЯ РЕАКЦІЙ У КІНЕМАТИЧНИХ ЗВ’ЯЗКАХ ЇХ ПРОСТОРОВИХ МЕХАНІЗМІВ
Burnishing operations can be performed using various types of equipment; however, the highest efficiency of this process is achieved when machines with work chambers capable of executing complex spatial movements are employed. Depending on the structural design, such machines differ in drive configuration, mechanism kinematics, and technological capabilities, enabling a wide range of operations including grinding, polishing, glazing, surface strengthening, sprue removal, and mixing of heterogeneous components. The structural foundation of these machines typically consists of spatial mechanisms based on rotational kinematic pairs. One of the most important application areas of such machines is the automotive industry, where burnishing is widely used for processing both metal and polymer parts. The process is especially efficient in serial and mass production, where stringent requirements are imposed on surface quality, productivity, and cost-efficiency. Burnishing allows for achieving a high surface finish, removing burrs, rounding edges, improving appearance, and enhancing the operational characteristics of components, which is particularly crucial for automotive assemblies such as transmissions, suspensions, and fasteners. A key condition for the long-term and stable operation of a burnishing machine is the accurate determination of loads in its kinematic pairs. In this study, a three-dimensional CAD model of an eight-link spatial mechanism with dual degrees of mobility was developed, in which the cylindrical chamber follows a complex spatial motion trajectory. Using the “SolidWorks Motion” software package, an analysis was carried out to assess the variation of reaction forces in all rotational joints of the mechanism depending on the geometric parameter δ, which characterizes the center-to-center distance of the chamber. The simulation results revealed the nature of the influence of parameter δ on the peak values of axial and radial reaction forces. It was found that as δ increases up to a certain threshold, a uniform distribution of loads among the kinematic joints is maintained. However, further increase in this parameter leads to localized overloading of specific joints. The obtained results can be applied in the design of burnishing machines for the mechanical engineering and automotive industries to ensure their reliable and energy-efficient operation.
- Open Access
- 28 November 2025
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- Vol. 2 (3(94)) , 203-210
МЕТОДОЛОГІЯ ОБРОБКИ ТА ЗБЕРЕЖЕННЯ ІНФОРМАЦІЇ В КОМП’ЮТЕРНІЙ СИСТЕМІ ДЛЯ ПРОВЕДЕННЯ ДОСЛІДЖЕНЬ ПРИ ПІДГОТОВЦІ І ПРЕЗЕНТАЦІЇ КВАЛІФІКАЦІЙНОЇ РОБОТИ
Розглянуто методологію використання мікроконтролера Arduino Leonardo при виконанні наукових досліджень і висвітлення отриманих результатів при написанні статті, під час виступу на конференції, а також в процесі захисту кваліфікаційної роботи. Встановлено, що існуючі апаратні та програмні засоби, що входять до комплектів мікроконтролерів Arduino можуть бути покладені в основу створення експериментального устаткування для проведення досліджень здобувачами освіти в різних галузях науки і техніки. Архітектура плат Arduino та їх програмного забезпечення дозволяють отримувати і обробляти інформацію з різного роду датчиків у вигляді аналогових і цифрових сигналів. Встановлені залежності між вхідними і вихідними величинами дозволяють підготувати змістовну презентацію для висвітлення отриманих результатів досліджень у доповідях на наукових конференціях, семінарах, а також у презентації кваліфікаційної роботи. На основі використання мікроконтролера Arduino Leonardo і персонального комп’ютера розроблено експериментальну установку для проведення експериментальних досліджень комп’ютерно-інтегрованої системи керування освітленням розумного будинку. Розроблено алгоритм і програмне забезпечення для вимірювання та реєстрації світлового потоку при використанні фоторезистора в якості датчика і світлодіодів для імітації джерел освітлення. Запропоновано метод збереження отриманих експериментальних даних у базі даних MySQL. Розроблено методологію проведення експериментальних досліджень режимів роботи комп’ютерно-інтегрованої системи керування освітленням.Отримана експериментальна залежність вихідної з фоторезистора напруги від величини світлового потоку внутрішнього світлодіода, яка підтверджує достовірність прийнятих вихідних положень в процесі створення програмного забезпечення розробленої експериментальної установки.
- 28 November 2025
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- Vol. 2 (3(94)) , 203-210
Open AccessМЕТОДОЛОГІЯ ОБРОБКИ ТА ЗБЕРЕЖЕННЯ ІНФОРМАЦІЇ В КОМП’ЮТЕРНІЙ СИСТЕМІ ДЛЯ ПРОВЕДЕННЯ ДОСЛІДЖЕНЬ ПРИ ПІДГОТОВЦІ І ПРЕЗЕНТАЦІЇ КВАЛІФІКАЦІЙНОЇ РОБОТИ
Розглянуто методологію використання мікроконтролера Arduino Leonardo при виконанні наукових досліджень і висвітлення отриманих результатів при написанні статті, під час виступу на конференції, а також в процесі захисту кваліфікаційної роботи. Встановлено, що існуючі апаратні та програмні засоби, що входять до комплектів мікроконтролерів Arduino можуть бути покладені в основу створення експериментального устаткування для проведення досліджень здобувачами освіти в різних галузях науки і техніки. Архітектура плат Arduino та їх програмного забезпечення дозволяють отримувати і обробляти інформацію з різного роду датчиків у вигляді аналогових і цифрових сигналів. Встановлені залежності між вхідними і вихідними величинами дозволяють підготувати змістовну презентацію для висвітлення отриманих результатів досліджень у доповідях на наукових конференціях, семінарах, а також у презентації кваліфікаційної роботи. На основі використання мікроконтролера Arduino Leonardo і персонального комп’ютера розроблено експериментальну установку для проведення експериментальних досліджень комп’ютерно-інтегрованої системи керування освітленням розумного будинку. Розроблено алгоритм і програмне забезпечення для вимірювання та реєстрації світлового потоку при використанні фоторезистора в якості датчика і світлодіодів для імітації джерел освітлення. Запропоновано метод збереження отриманих експериментальних даних у базі даних MySQL. Розроблено методологію проведення експериментальних досліджень режимів роботи комп’ютерно-інтегрованої системи керування освітленням.Отримана експериментальна залежність вихідної з фоторезистора напруги від величини світлового потоку внутрішнього світлодіода, яка підтверджує достовірність прийнятих вихідних положень в процесі створення програмного забезпечення розробленої експериментальної установки.
- Open Access
- 25 September 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 357 (5.1) , 277-283
ПОРІВНЯЛЬНЕ СИЛОВЕ ДОСЛІДЖЕННЯ ГАЛТУВАЛЬНИХ МАШИН З ТОЧКИ ЗОРУ ВИЗНАЧЕННЯ РЕАКЦІЙ У КІНЕМАТИЧНИХ ПАРАХ ШАРНІРНИХ ПРОСТОРОВИХ МЕХАНІЗМІВ
Tumbling operations can be performed using various types of equipment. The highest process intensity is achieved when using tumbling machines whose working containers perform complex spatial movements. To date, several types of such machines have been developed, each with specific design and technological features. These machines ensure efficient execution of a wide range of tumbling operations, including grinding, polishing, burnishing, surface strengthening of parts, removal of sprues, or mixing of materials. Structurally, these machines represent spatial mechanisms with complex kinematics, which are predominantly based on revolute kinematic pairs. A significant area of practical application for tumbling operations is the automotive industry, where this process is widely used for finishing both metallic and non-metallic components. Tumbling is particularly effective in serial and mass production, where high productivity, consistent surface quality, and low processing cost are key requirements. The process enables high surface finish, burr removal, edge rounding, improved appearance, and enhanced functional characteristics of parts — all of which are critical for elements such as transmissions, suspensions, fasteners, and other essential automotive components. To ensure the reliability and longevity of such machines, accurate calculation of loads in kinematic pairs is essential. In the course of this study, a 3D model of a tumbling machine with two driving links was developed using the CAD software “SolidWorks.” In this design, the container performs complex spatial motion. A force analysis was carried out to determine the dependency of reactions in all revolute kinematic pairs on variations in the center distance of the cylindrical container. The study revealed how this geometric parameter influences peak reaction forces that may arise within the kinematic pairs of the machine. The obtained results should be taken into account when designing similar types of tumbling equipment, especially for applications in mechanical and automotive engineering.
- 25 September 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 357 (5.1) , 277-283
Open AccessПОРІВНЯЛЬНЕ СИЛОВЕ ДОСЛІДЖЕННЯ ГАЛТУВАЛЬНИХ МАШИН З ТОЧКИ ЗОРУ ВИЗНАЧЕННЯ РЕАКЦІЙ У КІНЕМАТИЧНИХ ПАРАХ ШАРНІРНИХ ПРОСТОРОВИХ МЕХАНІЗМІВ
Tumbling operations can be performed using various types of equipment. The highest process intensity is achieved when using tumbling machines whose working containers perform complex spatial movements. To date, several types of such machines have been developed, each with specific design and technological features. These machines ensure efficient execution of a wide range of tumbling operations, including grinding, polishing, burnishing, surface strengthening of parts, removal of sprues, or mixing of materials. Structurally, these machines represent spatial mechanisms with complex kinematics, which are predominantly based on revolute kinematic pairs. A significant area of practical application for tumbling operations is the automotive industry, where this process is widely used for finishing both metallic and non-metallic components. Tumbling is particularly effective in serial and mass production, where high productivity, consistent surface quality, and low processing cost are key requirements. The process enables high surface finish, burr removal, edge rounding, improved appearance, and enhanced functional characteristics of parts — all of which are critical for elements such as transmissions, suspensions, fasteners, and other essential automotive components. To ensure the reliability and longevity of such machines, accurate calculation of loads in kinematic pairs is essential. In the course of this study, a 3D model of a tumbling machine with two driving links was developed using the CAD software “SolidWorks.” In this design, the container performs complex spatial motion. A force analysis was carried out to determine the dependency of reactions in all revolute kinematic pairs on variations in the center distance of the cylindrical container. The study revealed how this geometric parameter influences peak reaction forces that may arise within the kinematic pairs of the machine. The obtained results should be taken into account when designing similar types of tumbling equipment, especially for applications in mechanical and automotive engineering.
- Open Access
- 5 June 2025
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- Vol. 2 (2(93)) , 158-164
СТВОРЕННЯ ОБ’ЄКТІВ ІНТЕЛЕКТУАЛЬНОЇ ВЛАСНОСТІ НА ОСНОВІ ВИКОРИСТАННЯ МЕТОДІВ КОМП’ЮТЕРНОГО МАТЕМАТИЧНОГО МОДЕЛЮВАННЯ
Розглянуті сучасні тенденції створення об’єктів інтелектуальної власності на основі використання методів комп’ютерного математичного моделювання у легкій промисловості. Наведені результати досліджень у створенні нових технологій лиття під тиском деталей взуття з полімерних матеріалів. Запропоновано метод виготовлення багатоколірних підошов шляхом одночасного упорскування в прес-форму різних полімерних матеріалів. Розроблена комп’ютерна математична модель течії розплаву полімерного матеріалу в прес-формі, яка дозволяє визначити її конструктивні параметри для отримання підошов з заданими властивостями. Досліджено процес затягування верху взуття підвищеної формостійкості з шкіряної сировини, яка пройшла спеціальну обробку з використанням електроактивованого середовища та ензимів. Запропоновано технологію виготовлення комфортного взуття за індивідуальним замовленням, яка включає в себе процеси 3D-сканування стопи людини і 3D-друк накладок на поверхню колодки для врахування анатомічних особливостей замовника. Розроблено експериментальну установку для визначення тиску внутрішньої поверхні взуття на стопу людини, яка складається з персонального комп’ютера, і мікроконтролера Arduino з давачами сили. Впровадження комп’ютерних технологій для проведення теоретичних наукових досліджень у взуттєвій галузі відкриває можливості для здійснення математичного моделювання складних технологічних процесів і прогнозування експлуатаційних властивостей продукції, що випускається. Виготовлення дизайнерського взуття супроводжується створенням деталей складної геометричної форми, використанням нетрадиційних для взуттєвого виробництва матеріалів. Використання у взуттєвому виробництві інноваційних комп’ютерних технологій стало поштовхом для розробки і впровадження креативних і патентоспроможних технологічних, конструкторських і дизайнерських рішень.
- 5 June 2025
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- Vol. 2 (2(93)) , 158-164
Open AccessСТВОРЕННЯ ОБ’ЄКТІВ ІНТЕЛЕКТУАЛЬНОЇ ВЛАСНОСТІ НА ОСНОВІ ВИКОРИСТАННЯ МЕТОДІВ КОМП’ЮТЕРНОГО МАТЕМАТИЧНОГО МОДЕЛЮВАННЯ
Розглянуті сучасні тенденції створення об’єктів інтелектуальної власності на основі використання методів комп’ютерного математичного моделювання у легкій промисловості. Наведені результати досліджень у створенні нових технологій лиття під тиском деталей взуття з полімерних матеріалів. Запропоновано метод виготовлення багатоколірних підошов шляхом одночасного упорскування в прес-форму різних полімерних матеріалів. Розроблена комп’ютерна математична модель течії розплаву полімерного матеріалу в прес-формі, яка дозволяє визначити її конструктивні параметри для отримання підошов з заданими властивостями. Досліджено процес затягування верху взуття підвищеної формостійкості з шкіряної сировини, яка пройшла спеціальну обробку з використанням електроактивованого середовища та ензимів. Запропоновано технологію виготовлення комфортного взуття за індивідуальним замовленням, яка включає в себе процеси 3D-сканування стопи людини і 3D-друк накладок на поверхню колодки для врахування анатомічних особливостей замовника. Розроблено експериментальну установку для визначення тиску внутрішньої поверхні взуття на стопу людини, яка складається з персонального комп’ютера, і мікроконтролера Arduino з давачами сили. Впровадження комп’ютерних технологій для проведення теоретичних наукових досліджень у взуттєвій галузі відкриває можливості для здійснення математичного моделювання складних технологічних процесів і прогнозування експлуатаційних властивостей продукції, що випускається. Виготовлення дизайнерського взуття супроводжується створенням деталей складної геометричної форми, використанням нетрадиційних для взуттєвого виробництва матеріалів. Використання у взуттєвому виробництві інноваційних комп’ютерних технологій стало поштовхом для розробки і впровадження креативних і патентоспроможних технологічних, конструкторських і дизайнерських рішень.
- Open Access
- 26 May 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 351 (3.1) , 382-388
ВИКОРИСТАННЯ ІННОВАЦІЙНИХ КОМП’ЮТЕРНИХ ЗАСОБІВ І МЕТОДІВ НАУКОВИХ ДОСЛІДЖЕНЬ У ВЗУТТЄВІЙ ГАЛУЗІ
На базі персонального комп’ютера і мікроконтролера ArduinoUno розроблено експериментальну установку для вимірювання та реєстрації тиску взуття на стопу людини під час стояння і ходьби. Визначено комфортні величини тиску взуття на стопу, які лежать в межах від 10,5 кПа до 11,0 кПа. Запропоновано інноваційний метод проєктування внутрішньої форми взуття на основі результатів 3D-сканування стопи споживача і подальшої модифікації колодки накладками, виготовленими за технологією 3D-друку, відповідно до анатомічних особливостей людини. Розроблено технологію 3D-друку підошов підвищеної гнучкості для жіночого спортивного взуття. Проведені дослідження фізико-механічних властивостей зразків з поліетилентерефталат-гліколю (PETG), отриманих за технологією 3D-друку з різною густиною об’ємного наповнення, визначені величини розривного напруження і відносного подовження друкованих зразків. Отримані значення параметрів степеневого закону, що відображає залежність напружень від деформації при розтяганні друкованих зразків. Для апроксимації експериментальних кривих розтягання використано степеневий закон Людвіка, зокрема розраховано значення параметрів K і n для різної щільності друку. Показано, що зі збільшенням густини заповнення розривне напруження зростає, а відносна деформація зменшується, що свідчить про зміцнення структури матеріалу. Побудовано графічні залежності напруження-деформація для зразків з PETG при 60–100% щільності друку. Отримані результати дозволяють прогнозувати поведінку матеріалу під навантаженням і можуть бути використані при проєктуванні полімерних виробів, створених методом адитивного виробництва, для забезпечення їх надійності, функціональності, безпеки експлуатації та довговічності, а також адаптації до індивідуальних умов використання в різних сферах промисловості.
- 26 May 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 351 (3.1) , 382-388
Open AccessВИКОРИСТАННЯ ІННОВАЦІЙНИХ КОМП’ЮТЕРНИХ ЗАСОБІВ І МЕТОДІВ НАУКОВИХ ДОСЛІДЖЕНЬ У ВЗУТТЄВІЙ ГАЛУЗІ
На базі персонального комп’ютера і мікроконтролера ArduinoUno розроблено експериментальну установку для вимірювання та реєстрації тиску взуття на стопу людини під час стояння і ходьби. Визначено комфортні величини тиску взуття на стопу, які лежать в межах від 10,5 кПа до 11,0 кПа. Запропоновано інноваційний метод проєктування внутрішньої форми взуття на основі результатів 3D-сканування стопи споживача і подальшої модифікації колодки накладками, виготовленими за технологією 3D-друку, відповідно до анатомічних особливостей людини. Розроблено технологію 3D-друку підошов підвищеної гнучкості для жіночого спортивного взуття. Проведені дослідження фізико-механічних властивостей зразків з поліетилентерефталат-гліколю (PETG), отриманих за технологією 3D-друку з різною густиною об’ємного наповнення, визначені величини розривного напруження і відносного подовження друкованих зразків. Отримані значення параметрів степеневого закону, що відображає залежність напружень від деформації при розтяганні друкованих зразків. Для апроксимації експериментальних кривих розтягання використано степеневий закон Людвіка, зокрема розраховано значення параметрів K і n для різної щільності друку. Показано, що зі збільшенням густини заповнення розривне напруження зростає, а відносна деформація зменшується, що свідчить про зміцнення структури матеріалу. Побудовано графічні залежності напруження-деформація для зразків з PETG при 60–100% щільності друку. Отримані результати дозволяють прогнозувати поведінку матеріалу під навантаженням і можуть бути використані при проєктуванні полімерних виробів, створених методом адитивного виробництва, для забезпечення їх надійності, функціональності, безпеки експлуатації та довговічності, а також адаптації до індивідуальних умов використання в різних сферах промисловості.
- Open Access
- 26 May 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 351 (3.1) , 285-294
РОЗРОБЛЕННЯ МЕХАНІЗМІВ ПЕТЕЛЬНИКА ШВЕЙНИХ МАШИН З П-ПОДІБНОЮ ПЛАТФОРМОЮ ТА ЇХ КІНЕМАТИЧНИЙ СИНТЕЗ
Дослідження спрямоване на розроблення нових механізмів петельників із покращеними динамічними та функціональними характеристиками. Об'єктами досліджень стали запропоновані авторською групою структури механізмів. Для визначення їх параметрів використано методику кінематичного синтезу механізмів, розроблену кафедрою механічної інженерії Київського національного університету технологій та дизайну, а також відомі методи аналізу та синтезу важільних механізмів. Розроблено чотири нові механізми для швейних машин із П-подібною платформою, що мають спрощену будову, покращену динаміку, зменшену кількість ланок та розширені технологічні можливості. Також з використанням системи автоматизованого проектування SolidWorks була розроблена їх конструкція, що дозволить спростити їх впровадження у виробництво.
- 26 May 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 351 (3.1) , 285-294
Open AccessРОЗРОБЛЕННЯ МЕХАНІЗМІВ ПЕТЕЛЬНИКА ШВЕЙНИХ МАШИН З П-ПОДІБНОЮ ПЛАТФОРМОЮ ТА ЇХ КІНЕМАТИЧНИЙ СИНТЕЗ
Дослідження спрямоване на розроблення нових механізмів петельників із покращеними динамічними та функціональними характеристиками. Об'єктами досліджень стали запропоновані авторською групою структури механізмів. Для визначення їх параметрів використано методику кінематичного синтезу механізмів, розроблену кафедрою механічної інженерії Київського національного університету технологій та дизайну, а також відомі методи аналізу та синтезу важільних механізмів. Розроблено чотири нові механізми для швейних машин із П-подібною платформою, що мають спрощену будову, покращену динаміку, зменшену кількість ланок та розширені технологічні можливості. Також з використанням системи автоматизованого проектування SolidWorks була розроблена їх конструкція, що дозволить спростити їх впровадження у виробництво.
- Open Access
- 30 January 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 347 (1) , 20-25
ІНДИВІДУАЛЬНИЙ ПІДХІД У ПРОЄКТУВАННІ ТА ВИГОТОВЛЕННІ ВЗУТТЯ ДЛЯ ЛЮДЕЙ ІЗ ЗАХВОРЮВАННЯМ НА ЦУКРОВИЙ ДІАБЕТ
Type 2 diabetes is a disease that occurs in people at different ages when the body cannot produce and use insulin in sufficient quantities. Therefore, the disease is chronic and complex, since various organs and systems are affected at the same time. Special shoes and insoles are one of the means to combat this phenomenon. Such shoes create a comfortable environment in the middle of the product and protect the feet as much as possible from dangerous environmental factors.This work describes general information about the disease of diabetes, about the diabetic foot, about what shoes should be for type 2 diabetes, the main requirements, distinguishing features, and design features of orthopedic shoes of this subgroup. A step-by-step description of the stages of work on the manufacture of shoes for this purpose is presented, taking into account the customer's foot pathology in type 2 diabetes, factors of comfort and aesthetics.The work uses the following methods: organoleptic observations and measurements of feet, analysis of initial medical information regarding the diagnosis of the patient's feet, manual preparation and augmentation of certain segments of the shoe, development of the model design, as well as the manufacture of shoes by individual order under the conditions of Litini LLC.The individual project of orthopedic shoes is made taking into account the medical component in accordance with the diagnosis and recommendations of the endocrinologist, as well as taking into account the customer's requirements for functionality, ergonomics and aesthetics. As a result, ready-made shoes and a package of design and technological documentation for the product are presented. The manufactured shoes were tested in the conditions of daily experimental wearing of the product by the customer, which allowed to confirm the high quality of the product, to affirm the possibility of effective combination of the functional constructive component of this orthopedic shoe with the current aesthetic design.
- 30 January 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 347 (1) , 20-25
Open AccessІНДИВІДУАЛЬНИЙ ПІДХІД У ПРОЄКТУВАННІ ТА ВИГОТОВЛЕННІ ВЗУТТЯ ДЛЯ ЛЮДЕЙ ІЗ ЗАХВОРЮВАННЯМ НА ЦУКРОВИЙ ДІАБЕТ
Type 2 diabetes is a disease that occurs in people at different ages when the body cannot produce and use insulin in sufficient quantities. Therefore, the disease is chronic and complex, since various organs and systems are affected at the same time. Special shoes and insoles are one of the means to combat this phenomenon. Such shoes create a comfortable environment in the middle of the product and protect the feet as much as possible from dangerous environmental factors.This work describes general information about the disease of diabetes, about the diabetic foot, about what shoes should be for type 2 diabetes, the main requirements, distinguishing features, and design features of orthopedic shoes of this subgroup. A step-by-step description of the stages of work on the manufacture of shoes for this purpose is presented, taking into account the customer's foot pathology in type 2 diabetes, factors of comfort and aesthetics.The work uses the following methods: organoleptic observations and measurements of feet, analysis of initial medical information regarding the diagnosis of the patient's feet, manual preparation and augmentation of certain segments of the shoe, development of the model design, as well as the manufacture of shoes by individual order under the conditions of Litini LLC.The individual project of orthopedic shoes is made taking into account the medical component in accordance with the diagnosis and recommendations of the endocrinologist, as well as taking into account the customer's requirements for functionality, ergonomics and aesthetics. As a result, ready-made shoes and a package of design and technological documentation for the product are presented. The manufactured shoes were tested in the conditions of daily experimental wearing of the product by the customer, which allowed to confirm the high quality of the product, to affirm the possibility of effective combination of the functional constructive component of this orthopedic shoe with the current aesthetic design.
- Open Access
- 30 August 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (4 (130)) , 54-62
Synthesis of expert matrices in inductive system-analytical research based on fuzzy logic algorithm
The object of research is the process of inductive modeling of complex systems. The studies that were conducted related to the application of algorithms of the fuzzy logic theory were to coordinate the conclusions of top-level experts in system information-analytical research (SIAR) in the tasks of innovative design. The possibilities of constructing elements of expert matrices of results, as well as evaluating the effectiveness of such applications, are defined. Thanks to this, obtaining formal expert evaluations in numerical form became possible. Experimental studies have confirmed that the proposed approach to the application of fuzzy logic algorithms to the construction of matrices of expert evaluations of SIAR results is quite effective and simple to implement. In addition, this approach fits well into the general paradigm of the Group Method of Data Handling (GMDH). In particular, it was established that the possibility of «retraining» such a block without significant efforts of professional experts can have a positive result, as well as have a good effect on the economic and time parameters of the research project. The main calculation formulas for the algorithm for building a fuzzy system using a neural network in a system with two rules are given. The construction of a fuzzy information output system trained on expert evaluations in the Matlab system is shown. As a result, a technologically acceptable standard deviation of 0.28268 mg/l was obtained. It has been established that by accumulating a database (knowledge) and/or using an information monitoring system, it is possible to «additionally train» a fuzzy system periodically or according to the established quality criterion in the program mode, without involving experts in this process. Thus, there are reasons to assert the importance of using a fuzzy system as one of the tools in inductive SIAR procedures
- 30 August 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (4 (130)) , 54-62
Open AccessSynthesis of expert matrices in inductive system-analytical research based on fuzzy logic algorithm
The object of research is the process of inductive modeling of complex systems. The studies that were conducted related to the application of algorithms of the fuzzy logic theory were to coordinate the conclusions of top-level experts in system information-analytical research (SIAR) in the tasks of innovative design. The possibilities of constructing elements of expert matrices of results, as well as evaluating the effectiveness of such applications, are defined. Thanks to this, obtaining formal expert evaluations in numerical form became possible. Experimental studies have confirmed that the proposed approach to the application of fuzzy logic algorithms to the construction of matrices of expert evaluations of SIAR results is quite effective and simple to implement. In addition, this approach fits well into the general paradigm of the Group Method of Data Handling (GMDH). In particular, it was established that the possibility of «retraining» such a block without significant efforts of professional experts can have a positive result, as well as have a good effect on the economic and time parameters of the research project. The main calculation formulas for the algorithm for building a fuzzy system using a neural network in a system with two rules are given. The construction of a fuzzy information output system trained on expert evaluations in the Matlab system is shown. As a result, a technologically acceptable standard deviation of 0.28268 mg/l was obtained. It has been established that by accumulating a database (knowledge) and/or using an information monitoring system, it is possible to «additionally train» a fuzzy system periodically or according to the established quality criterion in the program mode, without involving experts in this process. Thus, there are reasons to assert the importance of using a fuzzy system as one of the tools in inductive SIAR procedures