Santosh Kumar Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Santosh Kumar Singh has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Avneet Kumar
Department of Mechanical and Automation, Harbin Institute of Technology, Shenzhen, China
12 shared publications - M. Raghuram
Electrical Engineering, Indian Institute of Technology Banaras Hindu University, 79203 Varanasi, Uttar Pradesh India 221005
12 shared publications - Xiaogang Xiong
School of Mechanical Engineering and Automation, Harbin Institute of Technology, Shenzhen, China
6 shared publications - Xuewei Pan
Harbin Institute of Technology, Shenzhen, China
6 shared publications - Ankita Dwivedi
Indian Institute of Technology (BHU)
5 shared publications - Aakash Singh
Electrical Engineering Department, IIT (BHU), Varanasi, India
4 shared publications
Latest Publications
- 29 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (3) , 3838-3849
Adaptive Nearest Level Modulation for Multilevel DC-Link Inverter With Enhanced Performance
Multilevel inverters are commonly used to interface renewable energy sources, like solar photovoltaic (PV) systems, to the grid. This article presents a method to enhance the performance of a single-phase asymmetric multilevel DC-link inverter (MLDCLI). The MLDCLI is designed to generate a 15-level staircase output utilizing three input DC sources. A simplified gate pulse generation (SGPG) technique is used to control the inverter. Moreover, an adaptive nearest-level modulation (ANLM) scheme is used to improve output quality. This scheme recalculates the switching angles automatically when the input DC voltages change. This helps to maintain a lower total harmonic distortion (THD) and a higher number of levels under variable DC input conditions. The proposed ANLM algorithm and switching logic are implemented using a Raspberry Pi Pico W microcontroller and experimentally validated. In addition, a PV system with maximum power point tracking (MPPT) was simulated in Typhoon HIL to assess the system response under dynamic irradiance. The suggested solution shows an attractive way to improve MLDCLI performance for solar PV applications. Adapting to source changes ensures robust operation under variable DC input conditions.
- 29 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (3) , 3838-3849
Adaptive Nearest Level Modulation for Multilevel DC-Link Inverter With Enhanced Performance
Multilevel inverters are commonly used to interface renewable energy sources, like solar photovoltaic (PV) systems, to the grid. This article presents a method to enhance the performance of a single-phase asymmetric multilevel DC-link inverter (MLDCLI). The MLDCLI is designed to generate a 15-level staircase output utilizing three input DC sources. A simplified gate pulse generation (SGPG) technique is used to control the inverter. Moreover, an adaptive nearest-level modulation (ANLM) scheme is used to improve output quality. This scheme recalculates the switching angles automatically when the input DC voltages change. This helps to maintain a lower total harmonic distortion (THD) and a higher number of levels under variable DC input conditions. The proposed ANLM algorithm and switching logic are implemented using a Raspberry Pi Pico W microcontroller and experimentally validated. In addition, a PV system with maximum power point tracking (MPPT) was simulated in Typhoon HIL to assess the system response under dynamic irradiance. The suggested solution shows an attractive way to improve MLDCLI performance for solar PV applications. Adapting to source changes ensures robust operation under variable DC input conditions.
- 25 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
A New Family of Super-Lift-Based Enhanced Gain Z-Source Boost DC-DC Converters: Analysis and Control
Achieving a very high voltage gain using a traditional boost DC-DC converter (TBDC) without resorting to extreme duty ratios remains a significant challenge. This paper proposes a novel family of single-switch Z-source DC-DC converters (ZSDCs), referred to as Super-Lift Z-source DC-DC Converters (SuLZSDCs), which leverage the super-lift technique to address this limitation. The integration of a super-lift cell not only enhances the voltage conversion ratio but also significantly reduces the voltage stress on the switching device. A comprehensive steady-state mathematical analysis is conducted to highlight the key features of the proposed topologies and is followed by a detailed comparison with existing Z-source converter configurations. Additionally, small-signal modelling of the enhanced SuLZSDC topology is carried out to analyze system dynamics and facilitate the design of a proportional–integral (PI) controller for output voltage regulation and stable closed-loop operation. To validate the theoretical findings and demonstrate the high-gain performance, a 400 W laboratory prototype is developed and tested. Experimental results under both steady-state and dynamic conditions confirm the effectiveness and practical feasibility of the proposed SuLZSDC topologies.
- 25 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
A New Family of Super-Lift-Based Enhanced Gain Z-Source Boost DC-DC Converters: Analysis and Control
Achieving a very high voltage gain using a traditional boost DC-DC converter (TBDC) without resorting to extreme duty ratios remains a significant challenge. This paper proposes a novel family of single-switch Z-source DC-DC converters (ZSDCs), referred to as Super-Lift Z-source DC-DC Converters (SuLZSDCs), which leverage the super-lift technique to address this limitation. The integration of a super-lift cell not only enhances the voltage conversion ratio but also significantly reduces the voltage stress on the switching device. A comprehensive steady-state mathematical analysis is conducted to highlight the key features of the proposed topologies and is followed by a detailed comparison with existing Z-source converter configurations. Additionally, small-signal modelling of the enhanced SuLZSDC topology is carried out to analyze system dynamics and facilitate the design of a proportional–integral (PI) controller for output voltage regulation and stable closed-loop operation. To validate the theoretical findings and demonstrate the high-gain performance, a 400 W laboratory prototype is developed and tested. Experimental results under both steady-state and dynamic conditions confirm the effectiveness and practical feasibility of the proposed SuLZSDC topologies.
- 8 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 7 (1) , 68-79
Enhanced Synthetic Inertia Controller for Grid-Forming Inverter-Based Virtual Synchronous Condenser
The proliferation of inverter based renewable energy sources (IBR) has inevitably resulted in insufficient inertia within the power system and creates challenges in maintaining stable frequency dynamics. Operating the IBR on maximum power point tracking (MPPT) and relying solely on the energy storage system for emulated inertia is not sufficient to keep the system stable. Despite this, limited efforts have been made to utilize STATCOMs as synchronous condensers, providing one possible approach to emulate the inertia. In response, this article proposes the implementation of a Grid-forming inverter based Virtual Synchronous Condenser (VSCON), which delivers inertia power through the stored energy in the DC-link capacitor and also supports reactive power compensation. The integration of a conventional synthetic inertia controller (SIC) into the VSCON exhibits limitations in handling DC-link dynamics, which can adversely affect overall system performance. To address this, an enhanced synthetic inertia controller (ESIC) is proposed, enabling the sequential handling of multiple frequency events and ensuring stable operation over a wider frequency range without causing over-modulation. Furthermore, the virtual inductor concept is employed to decouple the active and reactive power loops. With an adequate virtual inductance, it also achieves a $29\%$ reduction in the initial RoCoF. Finally, a hardware prototype of a VSCON is developed in the laboratory and validates superiority of the proposed ESIC over the SIC.
- 8 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 7 (1) , 68-79
Enhanced Synthetic Inertia Controller for Grid-Forming Inverter-Based Virtual Synchronous Condenser
The proliferation of inverter based renewable energy sources (IBR) has inevitably resulted in insufficient inertia within the power system and creates challenges in maintaining stable frequency dynamics. Operating the IBR on maximum power point tracking (MPPT) and relying solely on the energy storage system for emulated inertia is not sufficient to keep the system stable. Despite this, limited efforts have been made to utilize STATCOMs as synchronous condensers, providing one possible approach to emulate the inertia. In response, this article proposes the implementation of a Grid-forming inverter based Virtual Synchronous Condenser (VSCON), which delivers inertia power through the stored energy in the DC-link capacitor and also supports reactive power compensation. The integration of a conventional synthetic inertia controller (SIC) into the VSCON exhibits limitations in handling DC-link dynamics, which can adversely affect overall system performance. To address this, an enhanced synthetic inertia controller (ESIC) is proposed, enabling the sequential handling of multiple frequency events and ensuring stable operation over a wider frequency range without causing over-modulation. Furthermore, the virtual inductor concept is employed to decouple the active and reactive power loops. With an adequate virtual inductance, it also achieves a $29\%$ reduction in the initial RoCoF. Finally, a hardware prototype of a VSCON is developed in the laboratory and validates superiority of the proposed ESIC over the SIC.
- 17 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (6) , 8963-8975
Restricted Interleaving Phenomenon in Interleaved Boost PFC With Leg Sharing APF Circuit
Active buffering increases the power density of onboard chargers for electric vehicles. An active power filter (APF) is used to provide a stiff DC voltage to charge the battery. This DC voltage is obtained from a single-phase AC grid using a front-end power factor correction circuit (PFC). To enhance the quality of grid current, interleaving is used. This paper integrates a half-bridge APF with an interleaved totem-pole PFC. Leg sharing between PFC and APF can further reduce the number of components. However, it increases component stress and reduces the degree of freedom of the circuit. As a result, the current flow deviates from its intended path. In shared structure, the line current mimics the PFC operation but fails to follow the exact PFC profile. This becomes prominent in the case of interleaving. This phenomenon is explored for the first time and termed as “Restricted Interleaving Phenomenon”(RIP), which leads to increased input current ripple and affects the APF operation. This disturbance can be controlled by operating the circuit at a higher output voltage and increasing the APF switching frequency. Experimentally phenomenon is observed and analyzed in the proposed shared structure, followed by its control and impact on specific topologies.
- 17 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (6) , 8963-8975
Restricted Interleaving Phenomenon in Interleaved Boost PFC With Leg Sharing APF Circuit
Active buffering increases the power density of onboard chargers for electric vehicles. An active power filter (APF) is used to provide a stiff DC voltage to charge the battery. This DC voltage is obtained from a single-phase AC grid using a front-end power factor correction circuit (PFC). To enhance the quality of grid current, interleaving is used. This paper integrates a half-bridge APF with an interleaved totem-pole PFC. Leg sharing between PFC and APF can further reduce the number of components. However, it increases component stress and reduces the degree of freedom of the circuit. As a result, the current flow deviates from its intended path. In shared structure, the line current mimics the PFC operation but fails to follow the exact PFC profile. This becomes prominent in the case of interleaving. This phenomenon is explored for the first time and termed as “Restricted Interleaving Phenomenon”(RIP), which leads to increased input current ripple and affects the APF operation. This disturbance can be controlled by operating the circuit at a higher output voltage and increasing the APF switching frequency. Experimentally phenomenon is observed and analyzed in the proposed shared structure, followed by its control and impact on specific topologies.
- 19 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 5 (2) , 577-585
Stabilized High Voltage Gain With Reduced Common Mode Voltage Using SN-USMC for Remote Green EV Charging
The main contribution of this paper is to enhance the voltage gain of an ultra sparse matrix converter (USMC) with the help of the switched impedance network (SN) and also improve the common mode voltage (CMV) profile. Moreover, it produces balanced output voltage even during disturbed wind conditions. The prime focus of this paper is to provide information about the selection of active vectors and decide the switching sequence of the space vector modulation technique to reduce the peak-peak CMV. Controlling this switched network without affecting the stable operation of USMC has remained a challenging task, which the authors are carefully handling in this paper. This paper also discusses the analysis of the proposed converter for various supply frequencies, unbalanced supply, and output power factor operating ranges. Later, the proposed converter is compared with the earlier reported similar converters. The simulation and experimental results show that the proposed converter can boost the voltage gain beyond unity with reduced passive components. This would allow a stable, enhanced operating range of wind energy based AC-AC supply systems for EV charging.
- 19 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 5 (2) , 577-585
Stabilized High Voltage Gain With Reduced Common Mode Voltage Using SN-USMC for Remote Green EV Charging
The main contribution of this paper is to enhance the voltage gain of an ultra sparse matrix converter (USMC) with the help of the switched impedance network (SN) and also improve the common mode voltage (CMV) profile. Moreover, it produces balanced output voltage even during disturbed wind conditions. The prime focus of this paper is to provide information about the selection of active vectors and decide the switching sequence of the space vector modulation technique to reduce the peak-peak CMV. Controlling this switched network without affecting the stable operation of USMC has remained a challenging task, which the authors are carefully handling in this paper. This paper also discusses the analysis of the proposed converter for various supply frequencies, unbalanced supply, and output power factor operating ranges. Later, the proposed converter is compared with the earlier reported similar converters. The simulation and experimental results show that the proposed converter can boost the voltage gain beyond unity with reduced passive components. This would allow a stable, enhanced operating range of wind energy based AC-AC supply systems for EV charging.
- 3 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 10098-10107
Analysis and Control of Impedance Network Integrated High Voltage Gain USMC for Wider Output Frequency
The conventional ultra sparse matrix converter (USMC) attains a maximum voltage gain of 0.866, a crucial limitation of matrix converters. It can be overcome by integrating the impedance network with USMC. The primary focus of this article is to integrate switched boost network with USMC to improve the gain profile. This impedance network consists of semiconductor devices and energy storing elements. Controlling this impedance network without affecting the normal operation of USMC has remained a challenging task, which the authors have carefully handled in this article. This article investigates the load power factor effects on the overall voltage gain, which leads the converter to a nonzero discontinuous current mode. Further, this article deals with the total harmonic distortion dependency on the output frequency. In comparison to already reported converters, the proposed converter enhances the gain with minimum passive components. The simulation and experimental results (400 Hz load frequency) show that the proposed converter can boost the voltage gain greater than the unity with two passive elements.
- 3 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (9) , 10098-10107
Analysis and Control of Impedance Network Integrated High Voltage Gain USMC for Wider Output Frequency
The conventional ultra sparse matrix converter (USMC) attains a maximum voltage gain of 0.866, a crucial limitation of matrix converters. It can be overcome by integrating the impedance network with USMC. The primary focus of this article is to integrate switched boost network with USMC to improve the gain profile. This impedance network consists of semiconductor devices and energy storing elements. Controlling this impedance network without affecting the normal operation of USMC has remained a challenging task, which the authors have carefully handled in this article. This article investigates the load power factor effects on the overall voltage gain, which leads the converter to a nonzero discontinuous current mode. Further, this article deals with the total harmonic distortion dependency on the output frequency. In comparison to already reported converters, the proposed converter enhances the gain with minimum passive components. The simulation and experimental results (400 Hz load frequency) show that the proposed converter can boost the voltage gain greater than the unity with two passive elements.
- 15 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (5) , 6468-6479
Analysis and Design of Switched LC Converter With Reduced Voltage Stress for Photovoltaic Applications
High step-up voltage conversion is required in renewable energy systems. This paper presents a non-isolated high step-up DC-DC converter based on active switched-inductors (ASL) with switched capacitor cells (SCC). The unique selling proposition of the proposed converter is division of input current which reduces the inductor size. In the proposed topology, the capacitor and diode are arranged in such a way that they interconnect the input to the load side for obtaining high step-up ratio. The main advantages of the converter are high step-up ratio at a low duty cycle with low switch stress and low component count. Operating principles, design equations, and device stress are included in this paper. Moreover, small-signal analysis and its bode plots are presented here. In addition, the loss distribution is critically investigated. Finally, to verify the theoretical study, a laboratory prototype is built and tested at different operating points in continuous conduction mode (CCM).
- 15 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (5) , 6468-6479
Analysis and Design of Switched LC Converter With Reduced Voltage Stress for Photovoltaic Applications
High step-up voltage conversion is required in renewable energy systems. This paper presents a non-isolated high step-up DC-DC converter based on active switched-inductors (ASL) with switched capacitor cells (SCC). The unique selling proposition of the proposed converter is division of input current which reduces the inductor size. In the proposed topology, the capacitor and diode are arranged in such a way that they interconnect the input to the load side for obtaining high step-up ratio. The main advantages of the converter are high step-up ratio at a low duty cycle with low switch stress and low component count. Operating principles, design equations, and device stress are included in this paper. Moreover, small-signal analysis and its bode plots are presented here. In addition, the loss distribution is critically investigated. Finally, to verify the theoretical study, a laboratory prototype is built and tested at different operating points in continuous conduction mode (CCM).
- 20 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (4) , 1159-1169
Switching Strategy to Reduce Inductor Current Ripple and Common Mode Voltage in Quasi Z-Source Ultra Sparse Matrix Converter
This paper aims to reduce the ripple current in the inductor used in a Quasi Z-source Ultra Sparse Matrix Converter (QZSUSMC). The main limitations of the conventional Ultra Sparse Matrix Converter (USMC) are limited voltage gain $(\leq 0.866)$ and high common mode voltage (CMV). By integrating a quasi Z-source network in the DC link of USMC and providing a shoot-through (ST) state in a switching cycle, a voltage gain greater than unity can be achieved. Inductors are magnetised during the ST state and demagnetized during the nonshoot-through (NST) state. Hence with a proper arrangement of the ST and NST states, ripple in the inductor current can be minimised. In the proposed modulation, the total ST time is divided into six unequal parts and arranging them to minimize the inductor ripple current. in addition to it, proposed method also offers proper switching arrangements by using active vectors to attenuate peak-peak common mode voltage (CMV). As compared to the earlier reported methods, the proposed method produces a better inductor current ripple and a reduced peak of the CMV. Simulation and developed testing circuit results show the effectiveness of the proposed method.
- 20 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (4) , 1159-1169
Switching Strategy to Reduce Inductor Current Ripple and Common Mode Voltage in Quasi Z-Source Ultra Sparse Matrix Converter
This paper aims to reduce the ripple current in the inductor used in a Quasi Z-source Ultra Sparse Matrix Converter (QZSUSMC). The main limitations of the conventional Ultra Sparse Matrix Converter (USMC) are limited voltage gain $(\leq 0.866)$ and high common mode voltage (CMV). By integrating a quasi Z-source network in the DC link of USMC and providing a shoot-through (ST) state in a switching cycle, a voltage gain greater than unity can be achieved. Inductors are magnetised during the ST state and demagnetized during the nonshoot-through (NST) state. Hence with a proper arrangement of the ST and NST states, ripple in the inductor current can be minimised. In the proposed modulation, the total ST time is divided into six unequal parts and arranging them to minimize the inductor ripple current. in addition to it, proposed method also offers proper switching arrangements by using active vectors to attenuate peak-peak common mode voltage (CMV). As compared to the earlier reported methods, the proposed method produces a better inductor current ripple and a reduced peak of the CMV. Simulation and developed testing circuit results show the effectiveness of the proposed method.
- Open Access
- 1 December 2021
- Published by Marwah Infotech in UNIVERSITY JOURNAL OF DENTAL SCIENCES
- Vol. 8 (1)
A Novel Technique for Intraradicular Rehabilitation Using Mta and Light Transmitting Fibre Post: A Case Report
Restoring an endodontically treated teeth may become problematic due to inadequate sound radicular structure. In such cases where apices are flared ,its even more challenging to debride the canal and control the obturating material within the canal. Regarding rehabilitating the radicular structure; cast post have been used since older times. But it resulted in catastrophic root fracture with reduced remaining dentinal thickness, shadowing and graying of root and discoloration at the tooth’s gingival margin. Hence This case report presents a clinical case where intraradicular rehabilitation is done using MTA and light transimitting fibre post .
- 1 December 2021
- Published by Marwah Infotech in UNIVERSITY JOURNAL OF DENTAL SCIENCES
- Vol. 8 (1)
Open AccessA Novel Technique for Intraradicular Rehabilitation Using Mta and Light Transmitting Fibre Post: A Case Report
Restoring an endodontically treated teeth may become problematic due to inadequate sound radicular structure. In such cases where apices are flared ,its even more challenging to debride the canal and control the obturating material within the canal. Regarding rehabilitating the radicular structure; cast post have been used since older times. But it resulted in catastrophic root fracture with reduced remaining dentinal thickness, shadowing and graying of root and discoloration at the tooth’s gingival margin. Hence This case report presents a clinical case where intraradicular rehabilitation is done using MTA and light transimitting fibre post .
- 28 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (6) , 6405-6416
Quasi-Impedance-Source-Network-Based Nonisolated High-Step-Up DC–DC Converter
The high-step-up dc–dc converter is a key for numerous renewable-energy-based applications such as photovoltaic and fuel cells. Due to the low-voltage output of these renewable sources, a high-step-up stage is required, which bridges the gap of renewable to utility state. In this article, a noncoupled high-step-up $Z$ -source dc–dc converter, utilizing a quasi- $Z$ -source (QZS) network, is presented. The proposed topology is a combination of QZS structure and switched-capacitor cells, which maintains continuous input current and low-voltage stress across capacitors. In addition to these merits, the converter can achieve a high-step-up voltage at a low duty cycle, which results in lower conduction losses on semiconductor devices. The working principle, steady-state waveforms, related expressions, and comparative study are included in this article. The proposed converter can be extended for the use of a single-stage step-up $Z$ -source inverter and also for hybrid output applications. Finally, experimental results are presented to verify the feasibility of the converter in both open and closed loops.
- 28 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (6) , 6405-6416
Quasi-Impedance-Source-Network-Based Nonisolated High-Step-Up DC–DC Converter
The high-step-up dc–dc converter is a key for numerous renewable-energy-based applications such as photovoltaic and fuel cells. Due to the low-voltage output of these renewable sources, a high-step-up stage is required, which bridges the gap of renewable to utility state. In this article, a noncoupled high-step-up $Z$ -source dc–dc converter, utilizing a quasi- $Z$ -source (QZS) network, is presented. The proposed topology is a combination of QZS structure and switched-capacitor cells, which maintains continuous input current and low-voltage stress across capacitors. In addition to these merits, the converter can achieve a high-step-up voltage at a low duty cycle, which results in lower conduction losses on semiconductor devices. The working principle, steady-state waveforms, related expressions, and comparative study are included in this article. The proposed converter can be extended for the use of a single-stage step-up $Z$ -source inverter and also for hybrid output applications. Finally, experimental results are presented to verify the feasibility of the converter in both open and closed loops.