Xiaojue Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaojue Zhu has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Detlef Lohse
University of Twente
17 shared publications Roberto Verzicco
13 shared publications- Chao Sun
Tsinghua University
9 shared publications - Richard Johannes Antonius Maria Stevens
Physics of Fluids Group, Max Planck Center for Complex Fluid Dynamics, J. M. Burgers Center for Fluid Dynamics, University of Twente, Enschede, the Netherlands
9 shared publications Detlef Lohse
7 shared publicationsVarghese Mathai
Department of Physics University of Massachusetts Amherst MA USA
7 shared publications
Latest Publications
- Open Access
- 23 July 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1039
Three-dimensional turbulent free-surface flow past a submerged horizontal cylinder: combined dependence on Froude number and gap ratio
Free-surface response to flow past a fully submerged circular cylinder is known to be governed by the Froude number italic Fr $\textit{Fr}$ and the gap ratio upper G $G$ . However, most previous work has primarily examined this combined dependence in two-dimensional configurations at low Reynolds numbers. Here, three-dimensional high-resolution numerical simulations are conducted to investigate turbulent two-phase free-surface flow past a fully submerged circular cylinder at high Froude numbers ( 0.8 less than or slanted equals italic Fr less than or slanted equals 2.0 $0.8 \leqslant \textit{Fr} \leqslant 2.0$ ) and small gap ratios ( 0.025 less than or slanted equals upper G less than or slanted equals 0.4 $0.025 \leqslant G \leqslant 0.4$ ), at a Reynolds number italic Re equals 2000 $\textit{Re} = 2000$ and a Weber number italic We equals 1000 $\textit{We} = 1000$ , corresponding to a fully turbulent regime and small surface tension. The investigated parameter space corresponds to a flow regime where wake-induced interface disruption generates bubbles over a broad range of scales. This mechanism is of practical significance for engineering applications involving naval and offshore structures. The upstream and downstream free-surface flow patterns are classified. Free-surface breaking upstream of the cylinder is reported for 1.1 less than or slanted equals italic Fr less than or slanted equals 1.4 $1.1 \leqslant \textit{Fr} \leqslant 1.4$ , and its physical mechanism and occurrence condition are discussed. Downstream, as the breaking pattern transitions from spilling to plunging with increasing Froude number, the bubble number density spectrum exhibits distinct scaling behaviour. While a combined negative 4.3 $-4.3$ and negative 5.83 $-5.83$ power-law regime persists over a range of conditions, a negative 10 divided by 3 $-10/3$ scaling emerges under stronger plunging events with respect to the effective bubble radius. The frequency characteristics of the cylinder’s lift and drag coefficients associated with the transition from two-phase to single-phase flow are identified. Variations in mean statistical quantities with respect to italic Fr $\textit{Fr}$ and upper G $G$ confirm the coupled influence of these parameters, with increasing italic Fr $\textit{Fr}$ or upper G $G$ enhancing flow symmetry and promoting momentum transport within the jet-like flow above the cylinder. A combined analysis of vorticity transport, shear-layer dynamics, bubble statistics and turbulence properties elucidates how Froude number and gap ratio govern momentum exchange and air entrainment in high-Froude-number, small-gap-ratio flows. This study provides new mechanistic insight and numerical evidence for understanding interactions between highly deformable free surfaces and bluff-body wakes.- 23 July 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1039
Open AccessThree-dimensional turbulent free-surface flow past a submerged horizontal cylinder: combined dependence on Froude number and gap ratio
Free-surface response to flow past a fully submerged circular cylinder is known to be governed by the Froude number italic Fr $\textit{Fr}$ and the gap ratio upper G $G$ . However, most previous work has primarily examined this combined dependence in two-dimensional configurations at low Reynolds numbers. Here, three-dimensional high-resolution numerical simulations are conducted to investigate turbulent two-phase free-surface flow past a fully submerged circular cylinder at high Froude numbers ( 0.8 less than or slanted equals italic Fr less than or slanted equals 2.0 $0.8 \leqslant \textit{Fr} \leqslant 2.0$ ) and small gap ratios ( 0.025 less than or slanted equals upper G less than or slanted equals 0.4 $0.025 \leqslant G \leqslant 0.4$ ), at a Reynolds number italic Re equals 2000 $\textit{Re} = 2000$ and a Weber number italic We equals 1000 $\textit{We} = 1000$ , corresponding to a fully turbulent regime and small surface tension. The investigated parameter space corresponds to a flow regime where wake-induced interface disruption generates bubbles over a broad range of scales. This mechanism is of practical significance for engineering applications involving naval and offshore structures. The upstream and downstream free-surface flow patterns are classified. Free-surface breaking upstream of the cylinder is reported for 1.1 less than or slanted equals italic Fr less than or slanted equals 1.4 $1.1 \leqslant \textit{Fr} \leqslant 1.4$ , and its physical mechanism and occurrence condition are discussed. Downstream, as the breaking pattern transitions from spilling to plunging with increasing Froude number, the bubble number density spectrum exhibits distinct scaling behaviour. While a combined negative 4.3 $-4.3$ and negative 5.83 $-5.83$ power-law regime persists over a range of conditions, a negative 10 divided by 3 $-10/3$ scaling emerges under stronger plunging events with respect to the effective bubble radius. The frequency characteristics of the cylinder’s lift and drag coefficients associated with the transition from two-phase to single-phase flow are identified. Variations in mean statistical quantities with respect to italic Fr $\textit{Fr}$ and upper G $G$ confirm the coupled influence of these parameters, with increasing italic Fr $\textit{Fr}$ or upper G $G$ enhancing flow symmetry and promoting momentum transport within the jet-like flow above the cylinder. A combined analysis of vorticity transport, shear-layer dynamics, bubble statistics and turbulence properties elucidates how Froude number and gap ratio govern momentum exchange and air entrainment in high-Froude-number, small-gap-ratio flows. This study provides new mechanistic insight and numerical evidence for understanding interactions between highly deformable free surfaces and bluff-body wakes. - Open Access
- 17 June 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1037
Transient growth underpins superstructures and near-wall scales in turbulent convection
Turbulent convection is a fundamental transport process that shapes weather and climate, powers flows in planetary interiors and stars, and limits the performance of energy and heat-transfer technologies. Yet how these flows organise simultaneously into large-scale ‘superstructures’ and small-scale near-wall patterns remains unclear. Here, using Rayleigh–Bénard convection with large domain size, we show that both structures are captured by optimal linear modes that maximise transient energy amplification, identified via linear analysis based on turbulent mean profiles. Two amplification regimes emerge with clear scale separation: large-scale modes spanning the full central domain with horizontal wavelengths tilde 6 ${\sim} 6$ times the plate separation and small-scale modes confined near the walls at tilde 11 ${\sim} 11$ times the thermal boundary layer thickness. These results indicate that linear energy amplification plays an important organising role in multiscale turbulent convection and establish a unifying link to analogous non-modal processes in wall-bounded shear turbulence.- 17 June 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1037
Open AccessTransient growth underpins superstructures and near-wall scales in turbulent convection
Turbulent convection is a fundamental transport process that shapes weather and climate, powers flows in planetary interiors and stars, and limits the performance of energy and heat-transfer technologies. Yet how these flows organise simultaneously into large-scale ‘superstructures’ and small-scale near-wall patterns remains unclear. Here, using Rayleigh–Bénard convection with large domain size, we show that both structures are captured by optimal linear modes that maximise transient energy amplification, identified via linear analysis based on turbulent mean profiles. Two amplification regimes emerge with clear scale separation: large-scale modes spanning the full central domain with horizontal wavelengths tilde 6 ${\sim} 6$ times the plate separation and small-scale modes confined near the walls at tilde 11 ${\sim} 11$ times the thermal boundary layer thickness. These results indicate that linear energy amplification plays an important organising role in multiscale turbulent convection and establish a unifying link to analogous non-modal processes in wall-bounded shear turbulence. - Open Access
- 26 May 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1035
Formation of superswells and domes in layered turbulent convection systems
Superswells and domes – large-scale, persistent interface deformations – are key features in geophysical and multiphase systems driven by thermal convection. These structures often emerge in layered convective systems, such as Earth’s mantle or two-fluid industrial processes, where buoyancy contrasts and fluid properties create complex interface dynamics. However, the physical mechanisms governing the formation of these structures remain poorly understood. Here, we use high-resolution direct numerical simulations of two-layer Rayleigh–Bénard convection to investigate how the Prandtl number ( $\textit{Pr}$ ) and buoyancy number ( $B$ ) govern transitions in interfacial morphology. At a fixed Rayleigh number ( $\textit{Ra}$ ), we identify three distinct regimes: stratified convection at high $B$ , where compositional buoyancy suppresses interfacial motion; an interfacial fragmentation regime at low $\textit{Pr}$ and $B$ , driven by inertial–thermal buoyant balance; and a transitional dome-forming regime within a $\textit{Pr}$ -dependent range, where viscous and buoyant forces deform the interface into coherent, superswell-like structures. A theoretical phase diagram predicts these transitions and agrees well with simulation results. These findings provide mechanistic insight into interfacial phase behaviour in thermally driven flows, offering a framework that links geophysical surface features with underlying convective dynamics and informing the control of interfacial morphology in complex multiphase systems.- 26 May 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1035
Open AccessFormation of superswells and domes in layered turbulent convection systems
Superswells and domes – large-scale, persistent interface deformations – are key features in geophysical and multiphase systems driven by thermal convection. These structures often emerge in layered convective systems, such as Earth’s mantle or two-fluid industrial processes, where buoyancy contrasts and fluid properties create complex interface dynamics. However, the physical mechanisms governing the formation of these structures remain poorly understood. Here, we use high-resolution direct numerical simulations of two-layer Rayleigh–Bénard convection to investigate how the Prandtl number ( $\textit{Pr}$ ) and buoyancy number ( $B$ ) govern transitions in interfacial morphology. At a fixed Rayleigh number ( $\textit{Ra}$ ), we identify three distinct regimes: stratified convection at high $B$ , where compositional buoyancy suppresses interfacial motion; an interfacial fragmentation regime at low $\textit{Pr}$ and $B$ , driven by inertial–thermal buoyant balance; and a transitional dome-forming regime within a $\textit{Pr}$ -dependent range, where viscous and buoyant forces deform the interface into coherent, superswell-like structures. A theoretical phase diagram predicts these transitions and agrees well with simulation results. These findings provide mechanistic insight into interfacial phase behaviour in thermally driven flows, offering a framework that links geophysical surface features with underlying convective dynamics and informing the control of interfacial morphology in complex multiphase systems. - Open Access
- 14 May 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1035
Quantifying bulk temperature and boundary layer asymmetry in spherical and annular turbulent convection with boundary layer theories
We investigate thermal boundary layer (BL) asymmetry in turbulent Rayleigh–Bénard convection (RBC) under both spherical and annular geometries using different BL theories. Unlike planar RBC, the spherical and annular configurations exhibit asymmetric thermal BLs near the inner and outer boundaries due to boundary curvature and non-uniform radial gravity. We generalise three BL frameworks – the Prandtl–Blasius BL model, the steady free-convective model and the fluctuating BL model – and apply them to both geometries. Direct numerical simulations (DNSs), based on the Oberbeck–Boussinesq equations, are performed in three-dimensional spherical RBC and three-dimensional annular RBC for various radius ratios ( $\eta$ ), gravity profiles and also Prandtl numbers ( $ \textit{Pr}$ ), to compare with the predictions of the extended BL models. We find that the BL asymmetries predicted by both the extended steady free-convective BL and the fluctuating BL agree well with DNS results, with the fluctuating BL model providing the best agreement for the mean temperature profiles. A force-balance analysis further shows that this better performance is consistent with the DNS observation that, in the wall-normal direction within the thermal BL, buoyancy is balanced primarily by the pressure-gradient force. This is consistent with the assumption underlying the steady free-convective and fluctuating BL models. Moreover, the fluctuating BL model explicitly accounts for the contribution of turbulent fluctuations to the heat flux, which further improves its agreement with the DNS mean temperature profiles. We derive analytical expressions for the bulk temperature and the thermal BL thickness ratio as functions of the radius ratio and gravity profile across different Prandtl-number regimes. These expressions are obtained by integrating the similarity thermal equation for both the inner and outer BLs using an approximate similarity streamfunction, and by closing the solutions through a heat-flux matching condition. The resulting leading-order expressions obtained from both the steady free-convective and fluctuating BL models are shown to be the same, and they agree well with DNS data. This analytical result provides a robust and practical tool for quantifying BL asymmetry in curved RBC systems.- 14 May 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1035
Open AccessQuantifying bulk temperature and boundary layer asymmetry in spherical and annular turbulent convection with boundary layer theories
We investigate thermal boundary layer (BL) asymmetry in turbulent Rayleigh–Bénard convection (RBC) under both spherical and annular geometries using different BL theories. Unlike planar RBC, the spherical and annular configurations exhibit asymmetric thermal BLs near the inner and outer boundaries due to boundary curvature and non-uniform radial gravity. We generalise three BL frameworks – the Prandtl–Blasius BL model, the steady free-convective model and the fluctuating BL model – and apply them to both geometries. Direct numerical simulations (DNSs), based on the Oberbeck–Boussinesq equations, are performed in three-dimensional spherical RBC and three-dimensional annular RBC for various radius ratios ( $\eta$ ), gravity profiles and also Prandtl numbers ( $ \textit{Pr}$ ), to compare with the predictions of the extended BL models. We find that the BL asymmetries predicted by both the extended steady free-convective BL and the fluctuating BL agree well with DNS results, with the fluctuating BL model providing the best agreement for the mean temperature profiles. A force-balance analysis further shows that this better performance is consistent with the DNS observation that, in the wall-normal direction within the thermal BL, buoyancy is balanced primarily by the pressure-gradient force. This is consistent with the assumption underlying the steady free-convective and fluctuating BL models. Moreover, the fluctuating BL model explicitly accounts for the contribution of turbulent fluctuations to the heat flux, which further improves its agreement with the DNS mean temperature profiles. We derive analytical expressions for the bulk temperature and the thermal BL thickness ratio as functions of the radius ratio and gravity profile across different Prandtl-number regimes. These expressions are obtained by integrating the similarity thermal equation for both the inner and outer BLs using an approximate similarity streamfunction, and by closing the solutions through a heat-flux matching condition. The resulting leading-order expressions obtained from both the steady free-convective and fluctuating BL models are shown to be the same, and they agree well with DNS data. This analytical result provides a robust and practical tool for quantifying BL asymmetry in curved RBC systems. - Open Access
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3230 (1)
Transient growth under turbulent mean temperature profiles in Rayleigh–Bénard turbulence
Transient growth analysis has proved to be a powerful tool for identifying and interpreting large-scale coherent structures in turbulent shear flows, even in the absence of modal instabilities. In turbulent Rayleigh–Bénard convection, large-scale thermal superstructures analogous to the outer large-scale motions in shear-driven turbulence have been widely established by experiments and numerical simulations. In this study, we examine whether a similar linear framework based on transient energy amplification can account for the emergence and characteristic length scales of these superstructures. By performing a linear energy amplification analysis about turbulent mean temperature profiles extracted from direct numerical simulations, we show that the dominant features of thermal superstructures are captured by optimal linear modes with strong transient growth. The linearized operator is rendered non-normal by the coupling associated with the mean temperature gradient, whose removal in simulations leads to rapid laminarization. The resulting optimal modes extend across the full depth of the domain and amplify at horizontal wavelengths of order six times the layer height, in close agreement with the superstructures observed in direct numerical simulations. These results demonstrate that linear energy amplification provides a physically grounded mechanism for the generation and sustenance of thermal superstructures in turbulent convection.
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3230 (1)
Open AccessTransient growth under turbulent mean temperature profiles in Rayleigh–Bénard turbulence
Transient growth analysis has proved to be a powerful tool for identifying and interpreting large-scale coherent structures in turbulent shear flows, even in the absence of modal instabilities. In turbulent Rayleigh–Bénard convection, large-scale thermal superstructures analogous to the outer large-scale motions in shear-driven turbulence have been widely established by experiments and numerical simulations. In this study, we examine whether a similar linear framework based on transient energy amplification can account for the emergence and characteristic length scales of these superstructures. By performing a linear energy amplification analysis about turbulent mean temperature profiles extracted from direct numerical simulations, we show that the dominant features of thermal superstructures are captured by optimal linear modes with strong transient growth. The linearized operator is rendered non-normal by the coupling associated with the mean temperature gradient, whose removal in simulations leads to rapid laminarization. The resulting optimal modes extend across the full depth of the domain and amplify at horizontal wavelengths of order six times the layer height, in close agreement with the superstructures observed in direct numerical simulations. These results demonstrate that linear energy amplification provides a physically grounded mechanism for the generation and sustenance of thermal superstructures in turbulent convection.
- Open Access
- 10 April 2026
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 708, A253
Effects of the radiative interior on solar inertial modes
Context. Solar inertial modes are believed to play important diagnostic and dynamical roles in the Sun’s differentially rotating convection zone. However, the coupling of these modes to the radiative interior has not yet been discussed. Aims. We aim to understand the dependence of the modes on the uniformly rotating sub-adiabatic region below the convection zone and determine whether this leads to measurable changes at the surface. Methods. We used the Dedalus code to compute linear eigenmodes in the inertial frequency range in a setup that includes both the convection zone and the radiative interior down to 0.5 R ⊙ . We imposed free-surface boundary conditions at both radial boundaries. For comparison, we also computed the eigenmodes in a setup restricted to the convection zone. Results. We find that including the radiative zone only slightly modifies the frequencies and surface eigenfunctions, except for some modes with significant radial motion (high-frequency retrograde and prograde columnar modes). On the other hand, most modes penetrate significantly into the overshooting layer below the convection zone. This reduces their growth rates and distorts their eigenfunctions near the base of the convection zone. Furthermore, the uniformly rotating sub-adiabatic radiative zone supports oscillations due to Rossby modes of all possible spherical harmonics and radial nodes. In particular, when the nearest inertial mode in frequency space lies within around 10 nHz and shares the same north–south symmetry, these Rossby modes evolve into mixed modes characterized by significant motions within both the radiative and convection zones. However, such mixed modes have a high mode mass in the radiative interior and thus will be difficult to excite stochastically via convection.
- 10 April 2026
- Published by EDP Sciences in Astronomy & Astrophysics
- Vol. 708, A253
Open AccessEffects of the radiative interior on solar inertial modes
Context. Solar inertial modes are believed to play important diagnostic and dynamical roles in the Sun’s differentially rotating convection zone. However, the coupling of these modes to the radiative interior has not yet been discussed. Aims. We aim to understand the dependence of the modes on the uniformly rotating sub-adiabatic region below the convection zone and determine whether this leads to measurable changes at the surface. Methods. We used the Dedalus code to compute linear eigenmodes in the inertial frequency range in a setup that includes both the convection zone and the radiative interior down to 0.5 R ⊙ . We imposed free-surface boundary conditions at both radial boundaries. For comparison, we also computed the eigenmodes in a setup restricted to the convection zone. Results. We find that including the radiative zone only slightly modifies the frequencies and surface eigenfunctions, except for some modes with significant radial motion (high-frequency retrograde and prograde columnar modes). On the other hand, most modes penetrate significantly into the overshooting layer below the convection zone. This reduces their growth rates and distorts their eigenfunctions near the base of the convection zone. Furthermore, the uniformly rotating sub-adiabatic radiative zone supports oscillations due to Rossby modes of all possible spherical harmonics and radial nodes. In particular, when the nearest inertial mode in frequency space lies within around 10 nHz and shares the same north–south symmetry, these Rossby modes evolve into mixed modes characterized by significant motions within both the radiative and convection zones. However, such mixed modes have a high mode mass in the radiative interior and thus will be difficult to excite stochastically via convection.
- Open Access
- 11 March 2026
- Published by American Geophysical Union (AGU) in Geophysical Research Letters
- Vol. 53 (6)
Scaling of Latitude‐Dependent Heat Transport in Geostrophic Convection
Latitudinal variations in heat transport shape the thermal and magnetic evolution of rapidly rotating planets, stars, and icy moons. Although global simulations have revealed strong equatorial–polar contrasts, a predictive scaling theory has been lacking. Here we use rotating Rayleigh‐Bénard convection with tilted rotation and gravity axes to model dynamics at different latitudes in the geostrophic regime. We derive scaling relations for convective length scales and the Nusselt number that explain the latitude dependence of heat transfer. At high latitudes, near onset and above onset; at low latitudes, . These relations, validated against direct numerical simulations in spherical shells, unify local and global models. The results provide the first predictive framework for latitude‐dependent rotating thermal convection, with implications for Earth's core, gas giants, stellar interiors, and ocean circulation in icy moons.
- 11 March 2026
- Published by American Geophysical Union (AGU) in Geophysical Research Letters
- Vol. 53 (6)
Open AccessScaling of Latitude‐Dependent Heat Transport in Geostrophic Convection
Latitudinal variations in heat transport shape the thermal and magnetic evolution of rapidly rotating planets, stars, and icy moons. Although global simulations have revealed strong equatorial–polar contrasts, a predictive scaling theory has been lacking. Here we use rotating Rayleigh‐Bénard convection with tilted rotation and gravity axes to model dynamics at different latitudes in the geostrophic regime. We derive scaling relations for convective length scales and the Nusselt number that explain the latitude dependence of heat transfer. At high latitudes, near onset and above onset; at low latitudes, . These relations, validated against direct numerical simulations in spherical shells, unify local and global models. The results provide the first predictive framework for latitude‐dependent rotating thermal convection, with implications for Earth's core, gas giants, stellar interiors, and ocean circulation in icy moons.
- Open Access
- 19 January 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1027
Flapping dynamics of a compliant membrane in a uniform incoming flow
Recent theoretical and experimental investigations have revealed that flapping compliant membrane wings can significantly enhance propulsive performance (e.g. Tzezana & Breuer J. Fluid Mech. , 2019, vol. 862, pp. 871–888) and energy harvesting efficiency (e.g. Mathai et al. J. Fluid Mech. , 2022, vol. 942, p. R4) compared with rigid foils. Here, we numerically investigate the effects of the in-plane stretching stiffness (or aeroelastic number), $K_{\!S}$ , the flapping frequency, ${\textit{St}}_c$ , and the pitching amplitude, $\theta _0$ , on the propulsive performance of a compliant membrane undergoing combined heaving and pitching in uniform flow. Distinct optimal values of $K_{\!S}$ are identified that respectively maximise thrust and efficiency: thrust can be increased by 200 %, and efficiency by 100 %, compared with the rigid case. Interestingly, these optima do not occur at resonance but at frequency ratios (flapping to natural) below unity, and this ratio increases with flapping frequency. Using a force decomposition based on the second invariant of the velocity gradient tensor $Q$ , which measures the relative strength between the rotation and deformation of fluid elements, we show that thrust primarily arises from $Q$ -induced and body-acceleration forces. The concave membrane surface can trap the leading-edge vortex (LEV) generated during the previous half-stroke, generating detrimental $Q$ -induced drag. However, moderate concave membrane deformation weakens this LEV and enhances body-acceleration-induced thrust. Thus, the optimal $K_{\!S}$ for maximum thrust occurs below resonance, balancing beneficial deformation against excessive drag. Furthermore, by introducing the membrane’s deformation into a tangential angle at the leading edge and substituting it into an existing scaling law developed for rigid plates, we obtain predictive estimates for the thrust and power coefficients of the membrane. The good agreement confirms the validity of this approach and offers insights for performance prediction.- 19 January 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1027
Open AccessFlapping dynamics of a compliant membrane in a uniform incoming flow
Recent theoretical and experimental investigations have revealed that flapping compliant membrane wings can significantly enhance propulsive performance (e.g. Tzezana & Breuer J. Fluid Mech. , 2019, vol. 862, pp. 871–888) and energy harvesting efficiency (e.g. Mathai et al. J. Fluid Mech. , 2022, vol. 942, p. R4) compared with rigid foils. Here, we numerically investigate the effects of the in-plane stretching stiffness (or aeroelastic number), $K_{\!S}$ , the flapping frequency, ${\textit{St}}_c$ , and the pitching amplitude, $\theta _0$ , on the propulsive performance of a compliant membrane undergoing combined heaving and pitching in uniform flow. Distinct optimal values of $K_{\!S}$ are identified that respectively maximise thrust and efficiency: thrust can be increased by 200 %, and efficiency by 100 %, compared with the rigid case. Interestingly, these optima do not occur at resonance but at frequency ratios (flapping to natural) below unity, and this ratio increases with flapping frequency. Using a force decomposition based on the second invariant of the velocity gradient tensor $Q$ , which measures the relative strength between the rotation and deformation of fluid elements, we show that thrust primarily arises from $Q$ -induced and body-acceleration forces. The concave membrane surface can trap the leading-edge vortex (LEV) generated during the previous half-stroke, generating detrimental $Q$ -induced drag. However, moderate concave membrane deformation weakens this LEV and enhances body-acceleration-induced thrust. Thus, the optimal $K_{\!S}$ for maximum thrust occurs below resonance, balancing beneficial deformation against excessive drag. Furthermore, by introducing the membrane’s deformation into a tangential angle at the leading edge and substituting it into an existing scaling law developed for rigid plates, we obtain predictive estimates for the thrust and power coefficients of the membrane. The good agreement confirms the validity of this approach and offers insights for performance prediction. - 12 January 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1027, A6
Linear stability analysis of magnetoconvection in finite-sized systems: competition between spatial confinement and magnetic field
We present a linear stability analysis of two-dimensional magnetoconvection considering the effects of spatial confinement (characterised by the aspect ratio $\varGamma$ ) and magnetic field (characterised by the Hartmann number $\textit{Ha}_{i=x,y,z}$ with subscript representing its direction). It is found that when the magnetic field is perpendicular to the convection domain ( $y$ -direction), it does not affect the onset of convection due to zero Lorentz force. With a magnetic field in the $z$ (vertical) or $x$ (horizontal) directions, the onset of convection is delayed, resulting in a larger critical Rayleigh number $Ra_c$ for the onset of convection. We outline phase diagrams showing the dominating factors determining $Ra_c$ . When $\varGamma \leqslant 0.83\textit{Ha}_z^{-0.5}$ for vertical and $\varGamma \leqslant 0.66\textit{Ha}_x^{-1.01}$ for horizontal magnetic field, $Ra_c$ is mainly determined by the geometrical confinement with $Ra_c=502\varGamma ^{-4.0}$ . When $\varGamma \geqslant 2^{1/6}\pi ^{1/3}\textit{Ha}_z^{-1/3}$ for vertical and $\varGamma \geqslant 5$ for the horizontal magnetic field, $Ra_c$ is mainly determined by the magnetic field with $Ra_c=\pi ^2\textit{Ha}^2$ . In the intermediate regime, both the magnetic field and spatial confinement determine $Ra_c$ , and a horizontal magnetic field is found to suppress convection more than a vertical magnetic field. In addition, under a horizontal magnetic field, there exists a subregime characterised by $Ra_c = 9.9\,\varGamma ^{-2.0} \textit{Ha}_x^2$ , which is explained by a theoretical model. The magnetic field also modifies the length scale $\ell$ . For a vertical magnetic field, $\ell$ decreases with increasing $\textit{Ha}_z$ , following $\ell =2^{1/6}\pi ^{1/3}\textit{Ha}^{-1/3}$ . For a horizontal magnetic field, when $\varGamma \lt 0.62\textit{Ha}_x^{0.47}$ , the flow is a single-roll structure with $\ell$ being the width of the domain. The study thus shed new light on the interplay between magnetic field and spatial confinement.- 12 January 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1027, A6
Linear stability analysis of magnetoconvection in finite-sized systems: competition between spatial confinement and magnetic field
We present a linear stability analysis of two-dimensional magnetoconvection considering the effects of spatial confinement (characterised by the aspect ratio $\varGamma$ ) and magnetic field (characterised by the Hartmann number $\textit{Ha}_{i=x,y,z}$ with subscript representing its direction). It is found that when the magnetic field is perpendicular to the convection domain ( $y$ -direction), it does not affect the onset of convection due to zero Lorentz force. With a magnetic field in the $z$ (vertical) or $x$ (horizontal) directions, the onset of convection is delayed, resulting in a larger critical Rayleigh number $Ra_c$ for the onset of convection. We outline phase diagrams showing the dominating factors determining $Ra_c$ . When $\varGamma \leqslant 0.83\textit{Ha}_z^{-0.5}$ for vertical and $\varGamma \leqslant 0.66\textit{Ha}_x^{-1.01}$ for horizontal magnetic field, $Ra_c$ is mainly determined by the geometrical confinement with $Ra_c=502\varGamma ^{-4.0}$ . When $\varGamma \geqslant 2^{1/6}\pi ^{1/3}\textit{Ha}_z^{-1/3}$ for vertical and $\varGamma \geqslant 5$ for the horizontal magnetic field, $Ra_c$ is mainly determined by the magnetic field with $Ra_c=\pi ^2\textit{Ha}^2$ . In the intermediate regime, both the magnetic field and spatial confinement determine $Ra_c$ , and a horizontal magnetic field is found to suppress convection more than a vertical magnetic field. In addition, under a horizontal magnetic field, there exists a subregime characterised by $Ra_c = 9.9\,\varGamma ^{-2.0} \textit{Ha}_x^2$ , which is explained by a theoretical model. The magnetic field also modifies the length scale $\ell$ . For a vertical magnetic field, $\ell$ decreases with increasing $\textit{Ha}_z$ , following $\ell =2^{1/6}\pi ^{1/3}\textit{Ha}^{-1/3}$ . For a horizontal magnetic field, when $\varGamma \lt 0.62\textit{Ha}_x^{0.47}$ , the flow is a single-roll structure with $\ell$ being the width of the domain. The study thus shed new light on the interplay between magnetic field and spatial confinement.- 7 January 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1026, A41
Onset and length scales of wall modes in confined magnetoconvection with a vertical magnetic field
Using linear stability analysis, we study the onset and formation mechanism of wall modes in confined magnetoconvection cells with the degree of confinement characterised by the cell aspect ratio $\varGamma$ . We first outline the phase diagram of the dominating factors that determine the critical Rayleigh number $Ra_c$ for the onset of convection in the $\varGamma -Ha$ phase space, with $\textit{Ha}$ being the Hartmann number. Our study shows that $Ra_c$ is primarily determined by geometrical confinement, and bulk convection onset occurs with $Ra_c = 1090 \varGamma ^{-4.0}$ for $\varGamma \lt \varGamma _{c_1} = 1.21 \textit{Ha}^{-0.48}$ . No wall modes form and $Ra_c$ depends on the strength of both the confinement and magnetic field for $\varGamma _{c_1} \leqslant \varGamma \lt \varGamma _{c_2} = 4.07 \textit{Ha}^{-0.53}$ . For $\varGamma _{c_2}\leqslant \varGamma \lt \varGamma _{c_3}=0.99 \textit{Ha}^{-0.10}$ , wall modes emerge and $Ra_c$ drops below the bulk onset Rayleigh number for magnetoconvection. When $\varGamma \geqslant \varGamma _{c_3}$ , wall modes become fully developed with an onset Rayleigh number for wall modes $Ra_{c,w} \approx 65 \textit{Ha}^{1.5}$ . In this fully developed regime, the radial velocity profile and $Ra_{c,w}$ become independent of $\varGamma$ . Through analysing the length scales of wall modes and their interaction with spatial confinement, we show dynamically how wall modes emerge in confined cells: while the first layer with a characteristic length scale $\ell _1 = 1.04 \textit{Ha}^{-0.56}$ forms when $\varGamma \geqslant 5.39 \textit{Ha}^{-0.58}$ , the second layer with a characteristic length scale $\ell _2 = 4.94 \textit{Ha}^{-0.56}$ emerges when $\varGamma \geqslant 9.07 \textit{Ha}^{-0.53}$ . These scaling relations provide practical guidelines for experimental and numerical studies of the wall-mode dynamics.- 7 January 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1026, A41
Onset and length scales of wall modes in confined magnetoconvection with a vertical magnetic field
Using linear stability analysis, we study the onset and formation mechanism of wall modes in confined magnetoconvection cells with the degree of confinement characterised by the cell aspect ratio $\varGamma$ . We first outline the phase diagram of the dominating factors that determine the critical Rayleigh number $Ra_c$ for the onset of convection in the $\varGamma -Ha$ phase space, with $\textit{Ha}$ being the Hartmann number. Our study shows that $Ra_c$ is primarily determined by geometrical confinement, and bulk convection onset occurs with $Ra_c = 1090 \varGamma ^{-4.0}$ for $\varGamma \lt \varGamma _{c_1} = 1.21 \textit{Ha}^{-0.48}$ . No wall modes form and $Ra_c$ depends on the strength of both the confinement and magnetic field for $\varGamma _{c_1} \leqslant \varGamma \lt \varGamma _{c_2} = 4.07 \textit{Ha}^{-0.53}$ . For $\varGamma _{c_2}\leqslant \varGamma \lt \varGamma _{c_3}=0.99 \textit{Ha}^{-0.10}$ , wall modes emerge and $Ra_c$ drops below the bulk onset Rayleigh number for magnetoconvection. When $\varGamma \geqslant \varGamma _{c_3}$ , wall modes become fully developed with an onset Rayleigh number for wall modes $Ra_{c,w} \approx 65 \textit{Ha}^{1.5}$ . In this fully developed regime, the radial velocity profile and $Ra_{c,w}$ become independent of $\varGamma$ . Through analysing the length scales of wall modes and their interaction with spatial confinement, we show dynamically how wall modes emerge in confined cells: while the first layer with a characteristic length scale $\ell _1 = 1.04 \textit{Ha}^{-0.56}$ forms when $\varGamma \geqslant 5.39 \textit{Ha}^{-0.58}$ , the second layer with a characteristic length scale $\ell _2 = 4.94 \textit{Ha}^{-0.56}$ emerges when $\varGamma \geqslant 9.07 \textit{Ha}^{-0.53}$ . These scaling relations provide practical guidelines for experimental and numerical studies of the wall-mode dynamics.