Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jiancheng Tang has a total of 66 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigation on the Microstructure and Compressive Properties of W-15Mo Alloy Fabricated via Laser Powder Bed Fusion

    by Yuting Song, Yujie Ao, Qiao Deng, Linwei Zhang, Jilin Liu, Zichun Wu, Jiancheng Tang, Nan Ye

    Solid solution with molybdenum is an effective strategy for improving the overall performance of tungsten alloys, thereby enhancing their application potential in aerospace and other fields. In this study, highly dense W-Mo alloy specimens were successfully fabricated using laser powder bed fusion, followed by stress-relief annealing. The results show that the complete solid solution of molybdenum yields a fine columnar grain structure with weak texture. After stress-relief annealing, the residual stress decreases, the grain size increases slightly, and the fraction of the //building direction (BD) texture rises. Ultimately, W-Mo alloy specimens with excellent compressive properties are obtained, with compressive yield strength, ultimate compressive strength, and compressive strain reaching 879.5 MPa, 1257.3 MPa, and 16.6%, respectively. This work provides new insights into the fabrication of refractory alloys by laser powder bed fusion.

  • Open Access

    Effects of Nickel and Iron Content on the Microstructures and Mechanical Properties of Cemented Carbide with Coarse and Fine-Grained Heterostructures

    by Shuzhong Yang, Nan Ye, Mingxian Zhang, Yaru Zhu, Chenxin Zhang, Wentan Zhu, Fan Zhang, Jiafa Jiang, Jiancheng Tang

    Cemented carbides are composite materials that combine both structural and functional properties. However, the inherent trade-off between strength and toughness presents a significant challenge in fully leveraging the synergistic potential of these dual-phase materials. In this study, cemented carbides with coarse and fine-grained heterogeneous structure were fabricated. The effects of nickel (Ni) and iron (Fe) content on the microstructures and mechanical properties of these heterogeneously structured cemented carbides were systematically investigated. Microstructural analysis revealed that the fine-grained granules are uniformly embedded in the coarse-grained region, forming a typical network-like mixed-grain structure. The introduction of the heterogeneous structure enables cemented carbides to achieve a remarkable balance of high strength and toughness. Specifically, the materials exhibit optimal strength–toughness matching with a transverse rupture strength of 2949 MPa, a fracture toughness of 23.65 MPa·m−1/2, and a hardness of 1430 HV when the proportion of Ni and Fe content reaches 4.2 wt.%. The toughening mechanism is primarily attributed to the increased volume fraction and stabilized dimensions of CoNiFe binder phases, which promote interfacial decohesion at WC/WC and WC/binder boundaries while suppressing transgranular fracture. These mechanisms collectively contribute to enhanced toughening and crack propagation resistance. This study establishes foundational insights into achieving a synergistic combination of strength and toughness in cemented carbides.


  • Open Access

    Efficient Recovery of Cu from Wasted CPU Sockets by Slurry Electrolysis

    by Wenjing Chen, Manning Li, Jiancheng Tang

    In order to maximize the reuse of used electronic component resources, while reducing environmental pollution, Cu metal was recycled from wasted CPU sockets by the reformative slurry electrolysis method. However, the influences on the regulation of the Cu recovery rate and purity from waste CPU slots, by slurry electrolysis, has not been systematically elucidated in previous studies. In this work, the effects of H2SO4 concentration, slurry density, NH4Cl concentration, current density, and reaction time, on the recovery rate and purity of Cu in slurry electrolysis, were researched by systematic experimental methods. The results showed that the recycled metal elements were mainly present as powders from the cathode, rather than in the electrolyte. Moreover, the metallic elements in the cathode powder consisted of mostly Cu and small amounts of Sn and Ni. The recovery rate and purity of Cu were up to 96.19% and 93.72%, respectively, with the optimum conditions being: an H2SO4 concentration of 2 mol/L, slurry density of 30 g/L, NH4Cl concentration of 90 g/L, current density of 80 mA/cm2, and reaction time of 7 h. Compared with previous studies, the Cu recovered in this experiment was present in the cathode powder, which was more convenient for the subsequent processing. Meanwhile, the recovery rate of Cu was effectively improved. This is an important guideline for the subsequent application of slurry electrolysis for Cu recovery.


  • Nb2CTx MXene Cathode for High-Capacity Rechargeable Aluminum Batteries with Prolonged Cycle Lifetime

    by Jiahui Li, Fanshuai Zeng, Jehad K. El-Demellawi, Qicai Lin, Shengkun Xi, Junwei Wu, Jiancheng Tang, Xixiang Zhang, Xingjun Liu, Shaobo Tu

    Aluminum-ion batteries have garnered significant interest as a potentially safer and cheaper replacement for conventional lithium-ion batteries, offering a shorter charging time and denser storage capacity. Nonetheless, the progress in this field is considerably hampered by the limited availability of suitable cathode materials that can sustain the reversible intercalation of Al3+/[AlCl4]- ions, particularly after long cycles. Herein, we demonstrate that rechargeable Al batteries embedded with two-dimensional (2D) Nb2CTx MXene as a cathode material exhibit excellent capacity and exceptional long cyclic performance. We have successfully improved the initial electrochemical performance of Nb2CTx MXene after being properly delaminated to a single-layered microstructure and subjected to a post-synthesis calcining treatment. Compared to pristine Nb2CTx MXene, the Al battery embedded with the calcined Nb2CTx MXene cathode has, respectively, retained high capacities of 108 and 80 mAh g-1 after 500 cycles at current densities of 0.2 and 0.5 A g-1 in a wide voltage window (0.1-2.4 V). Noteworthily, the cyclic lifetime of Nb2CTx MXene was extended from ∼300 to >500 times after calcination. We reveal that attaining Nb2CTx nanosheets with a controllable d-spacing has promoted the migration of the [AlCl4]- and Al3+ ions in the MXene interlayers, leading to enhanced charge storage. Furthermore, we found out that the formation of niobium oxides and amorphous carbon after calcination probably benefits the electrochemical performance of Nb2CTx MXene electrode in Al batteries.


  • Open Access

    3D Porous MXene (Ti3C2Tx) Prepared by Alkaline-Induced Flocculation for Supercapacitor Electrodes

    by Weihua Chen, Jiancheng Tang, Peidong Cheng, Yunlong Ai, Yi Xu, Nan Ye

    2D layered MXene (Ti3C2Tx) with high conductivity and pseudo-capacitance properties presents great application potential with regard to electrode materials for supercapacitors. However, the self-restacking and agglomeration phenomenon between Ti3C2Tx layers retards ion transfer and limits electrochemical performance improvement. In this study, a 3D porous structure of Ti3C2Tx was obtained by adding alkali to a Ti3C2Tx colloid, which was followed by flocculation. Alkaline-induced flocculation is simple and effective, can be completed within minutes, and provides 3D porous networks. As 3D porous network structures present larger surface areas and more active sites, ions transfer accelerates, which is crucial with regard to the improvement of the superior capacitance and rate performance of electrodes. The sample processed with KOH (K-a-Ti3C2Tx) exhibited a high capacity of approximately 300.2 F g−1 at the current density of 1 A g−1. The capacitance of the samples treated with NaOH and LiOH is low. In addition, annealing is essential to further improve the capacitive performance of Ti3C2Tx. After annealing at 400 °C for 2 h in a vacuum tube furnace, the sample treated with KOH (K-A-Ti3C2Tx) exhibited an excellent specific capacitance of approximately 400.7 F g−1 at a current density of 1 A g−1, which is considerably higher than that of pristine Ti3C2Tx (228.2 F g−1). Furthermore, after 5000 charge–discharge cycles, the capacitance retention rate reached 89%. This result can be attributed to annealing, which can further remove unfavourable surface groups, such as –F or –Cl, and then improve conductivity capacitance and rate performance. This study can provide an effective approach to the preparation of high-performance supercapacitor electrode materials.


  • Open Access

    Microstructure and wear resistance of bimodal cemented carbide coating prepared by direct laser powder deposition

    by Nan Ye, Yunzhu Ma, Jiancheng Tang

    Compact spherical WC-12Co composite powder was deposited on 304 stainless steel substrate by multi-layer laser powder deposition (LPD) to fabricate cemented carbide coating. The phase constitution and microstructure of the coating as well as the feedstock powder were characterized. Microhardness and dry sliding wear tests were also performed to assess the mechanical properties of the coating. The results showed that the coating exhibited distinct microstructures and phase constitutions at different depths due to the various thermal cycles and the resulting heat damages of feedstock powders. The upper region of the coating (i.e. the wear resistant layer) exhibited bimodal microstructure in which the incompletely dissolved WC-Co composite particles preserved the original submicron sintered structure and secondary carbides were precipitated around them. Owing to the fine-grained strengthening of submicron WC grains in the undissolved areas, the microhardness of wear resistant layer was enhanced to 8 times that of the substrate. The wear rate of the cemented carbide coating was about three orders of magnitude lower than that of the substrate when dry sliding against Al2O3 ball under 10 N normal load. The bimodal structure of the wear resistant layer and the synergistic enhancement of differently sized carbides are the key factors for the excellent wear resistance of the coating.


  • Scalable Preparation of Ultrathin Graphene-Reinforced Copper Composite Foils with High Mechanical Properties and Excellent Heat Dissipation

    by Chaolong Wei, Nan Ye, Lekang Hong, Jiahui Yao, Weiyi Xia, Jie Mao, Yingjun Wang, Yuchao Zhao, Jiancheng Tang

    As an important basic material of electronic equipment, copper (Cu) foils should have a small thickness, good mechanical properties, and excellent thermal conductivity. However, preparing an ultrathin Cu foil with good properties remains challenging. Herein, we report an electroless deposition (ELD) strategy for the facile and scalable preparation of an ultrathin freestanding nickel-coated graphene (NCG)/Cu composite foil in a short time of 25 min. The NCG can significantly improve the mechanical and physical properties of composite foils. Experimental results reveal that the NCG/Cu composite foil manifests the best performance when the NCG concentration in an ELD bath was 30 mg/L. The composite foil evidenced a thickness of 1.1 μm, a high tensile strength of 338.7 MPa, and a high thermal conductivity of 431.2 W/mK. Compared with the pure Cu foil, both bending times and elastic modulus are increased by 298.1 and 737.3%, respectively. Remarkably, the composite foil has excellent heat dissipation performance, showing enormous potential as a heat sink material. This work proposes a new method for manufacturing the ultrathin graphene-reinforced Cu composite foil with high performance for numerous applications.