Anna E. Fox
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anna E. Fox has a total of 107 co-authors. Here are the top co-authors by number of shared publications:
- Paul D. Dresselhaus
National Institute of Standards and Technology, Boulder, CO, USA
18 shared publications - Samuel P. Benz
National Institute of Standards and Technology
18 shared publications - Nathan Edward Flowers-Jacobs
National Institute of Standards and Technology, Boulder, CO, USA
13 shared publications - Justus A. Brevik
National Institute of Standards and Technology, Boulder, CO, USA
6 shared publications - Peter F. Hopkins
National Institute of Standards and Technology
6 shared publications - Raegan L. Johnson-Wilke
National Institute of Standards and Technology, Boulder, CO, USA
5 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 0100402
Editorial: Preface to the Special Issue for the International Conference on Low-Temperature Detectors, LTD 2025
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (6) , 0100402
Editorial: Preface to the Special Issue for the International Conference on Low-Temperature Detectors, LTD 2025
- Open Access
- 11 June 2026
- Published by IOP Publishing in Metrologia
- Vol. 63 (3)
Leakage Current Effects with Programmable Josephson Voltage Standards
This work presents the results of evaluating and measuring the dc leakage effects associated with Programmable Josephson Voltage Standards (PJVS) caused by unintended currents flowing in the circuit. Two types of leakage error can occur in PJVS systems: 1) involves leakage currents to Earth ground, which typically result from the finite resistance of cable insulation and the bias electronics, and 2) leakage paths on the precision output leads giving rise to a voltage divider effect between the leads and the load impedance. Both effects impact the PJVS's measurement accuracy and must be monitored regularly. We have developed assessment methods, including both manual and automated measurements, that should be applied to any disseminated PJVS systems currently in use. If these recommended techniques are followed and the leakage current to Earth ground remains below 150 pA when the PJVS array is biased at 10 V, the resulting voltage error at the room-temperature terminals will be less than 0.2 nV.
- 11 June 2026
- Published by IOP Publishing in Metrologia
- Vol. 63 (3)
Open AccessLeakage Current Effects with Programmable Josephson Voltage Standards
This work presents the results of evaluating and measuring the dc leakage effects associated with Programmable Josephson Voltage Standards (PJVS) caused by unintended currents flowing in the circuit. Two types of leakage error can occur in PJVS systems: 1) involves leakage currents to Earth ground, which typically result from the finite resistance of cable insulation and the bias electronics, and 2) leakage paths on the precision output leads giving rise to a voltage divider effect between the leads and the load impedance. Both effects impact the PJVS's measurement accuracy and must be monitored regularly. We have developed assessment methods, including both manual and automated measurements, that should be applied to any disseminated PJVS systems currently in use. If these recommended techniques are followed and the leakage current to Earth ground remains below 150 pA when the PJVS array is biased at 10 V, the resulting voltage error at the room-temperature terminals will be less than 0.2 nV.
- 7 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (7) , 6001705
Dielectric Encapsulated Niobium Films to Achieve Higher Processing Temperatures
To avoid degradation of circuit performance, fabrication processes for niobium-based superconductive electronics are typically limited to temperatures below 150°C. In this study, we investigated protective dielectric capping layers that preserve the superconducting properties of Niobium (Nb) wiring at processing temperatures as high as 400°C. To assess the thermal stability of Nb films, 400 nm thick Nb layers were deposited on oxidized silicon wafers and were either left uncapped or were intentionally capped with selected dielectric materials. The samples were subjected to post-deposition annealing in an argon atmosphere for comparison. Samples were annealed up to 450°C, and changes in room temperature sheet resistance were used as a proxy for film degradation and checked with cryogenic measurements of samples annealed up to 400°C. A sharp increase in room temperature sheet resistance, and a resulting decrease in residual resistivity ratio was observed in pristine Nb films above 300°C. We found that the ex-situ deposition of insulating covering (“cap”) reduces the onset of degradation. Notably, silicon oxide (SiO$\_{x}$) capping shows significant improvement and silicon nitride (Si$\_{x}$N$\_{y}$) capped samples exhibit minimal changes in resistance across the full annealing range. These results suggest that Si$\_{x}$N$\_{y}$ encapsulation as a dielectric “cap” preserves superconductive properties and offers an expanded thermal budget for Nb-based superconductive electronics, with implications for multilayer integration and scalable fabrication.
- 7 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (7) , 6001705
Dielectric Encapsulated Niobium Films to Achieve Higher Processing Temperatures
To avoid degradation of circuit performance, fabrication processes for niobium-based superconductive electronics are typically limited to temperatures below 150°C. In this study, we investigated protective dielectric capping layers that preserve the superconducting properties of Niobium (Nb) wiring at processing temperatures as high as 400°C. To assess the thermal stability of Nb films, 400 nm thick Nb layers were deposited on oxidized silicon wafers and were either left uncapped or were intentionally capped with selected dielectric materials. The samples were subjected to post-deposition annealing in an argon atmosphere for comparison. Samples were annealed up to 450°C, and changes in room temperature sheet resistance were used as a proxy for film degradation and checked with cryogenic measurements of samples annealed up to 400°C. A sharp increase in room temperature sheet resistance, and a resulting decrease in residual resistivity ratio was observed in pristine Nb films above 300°C. We found that the ex-situ deposition of insulating covering (“cap”) reduces the onset of degradation. Notably, silicon oxide (SiO$\_{x}$) capping shows significant improvement and silicon nitride (Si$\_{x}$N$\_{y}$) capped samples exhibit minimal changes in resistance across the full annealing range. These results suggest that Si$\_{x}$N$\_{y}$ encapsulation as a dielectric “cap” preserves superconductive properties and offers an expanded thermal budget for Nb-based superconductive electronics, with implications for multilayer integration and scalable fabrication.
- 16 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 8942-8955
Cryogenic On-Chip In Situ S -Parameter Calibration Using Superconducting Coplanar Waveguides
This article presents a new multiimpedance-state line (MISL) in situ scattering parameter (S-parameter) calibration technique using on-chip superconducting transmission lines at 4 K that enables cryogenic calibration in a fixed signal path without the need for cryogenic switches or a cryogenic probe station. The method uses coplanar waveguide (CPW) models based on various impedance states of niobium (Nb), which has zero dc resistance below 9 K and a monotonically increasing resistance from 10 K to room temperature. The different impedance states are accessed by heating the 4 K stage of a cryostat and injecting up to 245 mA of current into the line. Using these states, we solve for the unknowns in an eight-term error model through a least-squares analysis. We first validate the MISL calibration technique by comparing it with short-open-load-reciprocal (SOLR) calibrated measurements in a cryogenic probe station, finding transmission agreement within 0.2 dB and uncertainty overlap for nearly all frequencies up to 26.5 GHz. We then apply the method to calibrate Nb CPWs with and without embedded Josephson junctions (JJs), using a fixed wire bonded connection, and without the use of cryogenic switches or movable probes. Strong agreement with the CPW models is demonstrated, with uncertainty overlap and differences below 0.1 dB up to 4.6 GHz without JJs and up to 2.4 GHz with JJs; resonances cause interruptions beyond these frequencies.
- 16 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (11) , 8942-8955
Cryogenic On-Chip In Situ S -Parameter Calibration Using Superconducting Coplanar Waveguides
This article presents a new multiimpedance-state line (MISL) in situ scattering parameter (S-parameter) calibration technique using on-chip superconducting transmission lines at 4 K that enables cryogenic calibration in a fixed signal path without the need for cryogenic switches or a cryogenic probe station. The method uses coplanar waveguide (CPW) models based on various impedance states of niobium (Nb), which has zero dc resistance below 9 K and a monotonically increasing resistance from 10 K to room temperature. The different impedance states are accessed by heating the 4 K stage of a cryostat and injecting up to 245 mA of current into the line. Using these states, we solve for the unknowns in an eight-term error model through a least-squares analysis. We first validate the MISL calibration technique by comparing it with short-open-load-reciprocal (SOLR) calibrated measurements in a cryogenic probe station, finding transmission agreement within 0.2 dB and uncertainty overlap for nearly all frequencies up to 26.5 GHz. We then apply the method to calibrate Nb CPWs with and without embedded Josephson junctions (JJs), using a fixed wire bonded connection, and without the use of cryogenic switches or movable probes. Strong agreement with the CPW models is demonstrated, with uncertainty overlap and differences below 0.1 dB up to 4.6 GHz without JJs and up to 2.4 GHz with JJs; resonances cause interruptions beyond these frequencies.
- 14 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-7
Dual-Frequency-Bias Programmable Josephson Voltage Standard Circuit
This paper presents a 2 V programmable Josephson voltage standard with dual microwave frequency inputs and multiple output taps. The design provides three main features: (1) output voltages with nanovolt resolution, (2) the ability to perform a microwave frequency self-check based on a null voltage measurement, and (3) additional voltage output taps providing simultaneous 10:1 (or 5:1) divided voltage reference for resistive divider calibration. With low heat dissipation this device is well suited for implementation with a compact cryocooler as a turnkey traveling system.
- 14 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-7
Dual-Frequency-Bias Programmable Josephson Voltage Standard Circuit
This paper presents a 2 V programmable Josephson voltage standard with dual microwave frequency inputs and multiple output taps. The design provides three main features: (1) output voltages with nanovolt resolution, (2) the ability to perform a microwave frequency self-check based on a null voltage measurement, and (3) additional voltage output taps providing simultaneous 10:1 (or 5:1) divided voltage reference for resistive divider calibration. With low heat dissipation this device is well suited for implementation with a compact cryocooler as a turnkey traveling system.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Impact of Leakage Currents on Voltage Accuracy in the Josephson Arbitrary Waveform Synthesizer
The voltage errors related to ac leakage currents in Josephson arbitrary waveform synthesizer (JAWS) systems are significant contributors to the overall system accuracy. These ac leakage currents flow through paths (typically to ground) that are not part of the intended measurement circuit. This paper examines output voltage discrepancies between two different but nominally identical circuit halves on a single JAWS circuit and shows that this discrepancy is dominated by ac leakage currents through the stray capacitance in the compensation leads. Methods to minimize these voltage errors will be discussed along with their associated limitations.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Impact of Leakage Currents on Voltage Accuracy in the Josephson Arbitrary Waveform Synthesizer
The voltage errors related to ac leakage currents in Josephson arbitrary waveform synthesizer (JAWS) systems are significant contributors to the overall system accuracy. These ac leakage currents flow through paths (typically to ground) that are not part of the intended measurement circuit. This paper examines output voltage discrepancies between two different but nominally identical circuit halves on a single JAWS circuit and shows that this discrepancy is dominated by ac leakage currents through the stray capacitance in the compensation leads. Methods to minimize these voltage errors will be discussed along with their associated limitations.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (7) , 1-10
VHF Josephson Arbitrary Waveform Synthesizer
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (7) , 1-10
VHF Josephson Arbitrary Waveform Synthesizer
- Open Access
- 29 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (5)
AC metrology applications of the Josephson effect
The performance of programmable voltage signals that exploit the quantum behavior of superconducting Josephson junctions continues to improve and enhance measurements in metrology, communications, and quantum control. We review advances in pulse-driven digital synthesis techniques with Josephson-junction-based devices. Quantum-based synthesis of voltage waveforms has been demonstrated at frequencies up to 3 GHz and rms amplitudes up to 4 V. Josephson pulse generators have also been used to control and characterize superconducting qubits.
- 29 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (5)
Open AccessAC metrology applications of the Josephson effect
The performance of programmable voltage signals that exploit the quantum behavior of superconducting Josephson junctions continues to improve and enhance measurements in metrology, communications, and quantum control. We review advances in pulse-driven digital synthesis techniques with Josephson-junction-based devices. Quantum-based synthesis of voltage waveforms has been demonstrated at frequencies up to 3 GHz and rms amplitudes up to 4 V. Josephson pulse generators have also been used to control and characterize superconducting qubits.
- 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2047-2056
Quantum-Based Modulated Microwave Waveforms
This article presents a superconducting voltage source that generates modulated microwave waveforms with quantum-based stability. The voltage source—an RF Josephson Arbitrary Waveform Synthesizer (RF-JAWS)—uses a superconducting IC with an array of 4500 series-connected Josephson junctions (JJs) that are embedded in a coplanar waveguide (CPW) transmission line. The JJs are driven with 100-ps wide current pulses that force each JJ to generate voltage pulses with a quantized integrated area. A pulse sequence is created using a delta–sigma ( $\Delta$ – $\Sigma$ ) algorithm to generate a 101-tone waveform with a 40-MHz instantaneous bandwidth around 1005 MHz with a flat power distribution of $-$ 53 dBm and a Schroeder phase distribution. The JJ’s quantum-based nonlinearity produces an amplitude stability with respect to various drive and bias parameters of $\pm$ 0.005 dB and a detrended phase stability of $\pm $ 0.05 $^{\circ}$ . The stability of the source is verified without the need for calibrated measurements. Another $\Delta$ – $\Sigma$ pulse sequence generates a 10-MHz quadrature-phase shift-keying (QPSK) waveform on a 1005-MHz carrier that has the same stability and the mean error vector magnitude (EVM) of $-$ 48 dB. This work is a step toward creating a quantum-based reference source for power and cross-frequency phase calibrations, as well as a reference-modulated signal source for calibrating telecommunication links.
- 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2047-2056
Quantum-Based Modulated Microwave Waveforms
This article presents a superconducting voltage source that generates modulated microwave waveforms with quantum-based stability. The voltage source—an RF Josephson Arbitrary Waveform Synthesizer (RF-JAWS)—uses a superconducting IC with an array of 4500 series-connected Josephson junctions (JJs) that are embedded in a coplanar waveguide (CPW) transmission line. The JJs are driven with 100-ps wide current pulses that force each JJ to generate voltage pulses with a quantized integrated area. A pulse sequence is created using a delta–sigma ( $\Delta$ – $\Sigma$ ) algorithm to generate a 101-tone waveform with a 40-MHz instantaneous bandwidth around 1005 MHz with a flat power distribution of $-$ 53 dBm and a Schroeder phase distribution. The JJ’s quantum-based nonlinearity produces an amplitude stability with respect to various drive and bias parameters of $\pm$ 0.005 dB and a detrended phase stability of $\pm $ 0.05 $^{\circ}$ . The stability of the source is verified without the need for calibrated measurements. Another $\Delta$ – $\Sigma$ pulse sequence generates a 10-MHz quadrature-phase shift-keying (QPSK) waveform on a 1005-MHz carrier that has the same stability and the mean error vector magnitude (EVM) of $-$ 48 dB. This work is a step toward creating a quantum-based reference source for power and cross-frequency phase calibrations, as well as a reference-modulated signal source for calibrating telecommunication links.
- Open Access
- 1 August 2023
- Published by AIP Publishing in APL Photonics
- Vol. 8 (8)
Sub-GHz resolution line-by-line pulse shaper for driving superconducting circuits
We demonstrate a sub-GHz resolution, fully programmable Fourier-domain pulse shaper capable of generating arbitrary optical pulse patterns for superconducting circuit platforms. This high resolution allows line-by-line pulse shaping of a 1 GHz-spaced comb, and the pulse shaper can accommodate an optical bandwidth as large as 1 THz, which represents the highest resolution programmable line-by-line pulse shaping to our knowledge. Linear optical sampling with a dual-comb system confirms independent control of 1 GHz-spaced optical lines, and the low phase noise of the pulse shaper is characterized. We apply the pulse shaper as an optical drive for an array of Josephson junctions operating at a temperature of 4 K, where cryogenic photodetection of pulse doublets with user-defined separation characterizes the Josephson junction response. Furthermore, we demonstrate a pulse-density modulation pattern of 4 ps duration optical pulses that can serve as the high bandwidth drive of a quantum-based Josephson arbitrary waveform synthesizer. By leveraging the exquisite control, large bandwidth, and low noise of photonics, this represents an important advance toward the realization of high power and high spectral purity AC voltage standards at gigahertz frequencies without requiring 100 GHz bandwidth driving electronics.
- 1 August 2023
- Published by AIP Publishing in APL Photonics
- Vol. 8 (8)
Open AccessSub-GHz resolution line-by-line pulse shaper for driving superconducting circuits
We demonstrate a sub-GHz resolution, fully programmable Fourier-domain pulse shaper capable of generating arbitrary optical pulse patterns for superconducting circuit platforms. This high resolution allows line-by-line pulse shaping of a 1 GHz-spaced comb, and the pulse shaper can accommodate an optical bandwidth as large as 1 THz, which represents the highest resolution programmable line-by-line pulse shaping to our knowledge. Linear optical sampling with a dual-comb system confirms independent control of 1 GHz-spaced optical lines, and the low phase noise of the pulse shaper is characterized. We apply the pulse shaper as an optical drive for an array of Josephson junctions operating at a temperature of 4 K, where cryogenic photodetection of pulse doublets with user-defined separation characterizes the Josephson junction response. Furthermore, we demonstrate a pulse-density modulation pattern of 4 ps duration optical pulses that can serve as the high bandwidth drive of a quantum-based Josephson arbitrary waveform synthesizer. By leveraging the exquisite control, large bandwidth, and low noise of photonics, this represents an important advance toward the realization of high power and high spectral purity AC voltage standards at gigahertz frequencies without requiring 100 GHz bandwidth driving electronics.