Shuji Tamura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shuji Tamura has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
Kohji Tokimatsu
12 shared publications- Daniel W. Wilson
Department of Civil and Environmental Engineering, University of California, Davis, CA, USA
6 shared publications - Ross W. Boulanger
Univ. of California, Davis
6 shared publications Takenori Hida
The Univ. of Tokyo
6 shared publicationsAkihiko Uchida
4 shared publicationsC. Guney Olgun
4 shared publications
Latest Publications
- Open Access
- 20 November 2026
- Published by Springer Nature in Granular Matter
- Vol. 29 (1)
Modeling the transition of force propagation in granular media via a scalable compliance-based framework
To address the high computational cost of simulating static stress networks in granular assemblies, this study proposes a compliance-based reduced-order framework with $$\:O\left(N\right)$$ computational scalability. By employing a recursive force-distribution scheme based on local compliance, the method eliminates global stiffness matrix assembly. Structural heterogeneity is governed by a single disorder parameter, $$\:\chi\:$$ , enabling self-consistent force chain formation. The model reproduces fundamental granular phenomena, including exponential contact-stress distributions and the transition between unimodal and bimodal force propagation based on packing disorder. Applied to boundary value problems under rigid indentation, it captures continuum-like reaction stress distributions while accounting for microscopic fluctuations, wall-shear pressure reduction, and localized stress peaks at boundaries. Global energy balance errors remain within approximately 2.5%, and by suppressing widespread tensile forces, the framework effectively captures the macroscopic statistical properties of tension-cut global stiffness matrix solvers without non-linear iterations. This framework offers a low-cost, memory-efficient tool for static pre-failure stress analysis in granular mechanics.- 20 November 2026
- Published by Springer Nature in Granular Matter
- Vol. 29 (1)
Open AccessModeling the transition of force propagation in granular media via a scalable compliance-based framework
To address the high computational cost of simulating static stress networks in granular assemblies, this study proposes a compliance-based reduced-order framework with $$\:O\left(N\right)$$ computational scalability. By employing a recursive force-distribution scheme based on local compliance, the method eliminates global stiffness matrix assembly. Structural heterogeneity is governed by a single disorder parameter, $$\:\chi\:$$ , enabling self-consistent force chain formation. The model reproduces fundamental granular phenomena, including exponential contact-stress distributions and the transition between unimodal and bimodal force propagation based on packing disorder. Applied to boundary value problems under rigid indentation, it captures continuum-like reaction stress distributions while accounting for microscopic fluctuations, wall-shear pressure reduction, and localized stress peaks at boundaries. Global energy balance errors remain within approximately 2.5%, and by suppressing widespread tensile forces, the framework effectively captures the macroscopic statistical properties of tension-cut global stiffness matrix solvers without non-linear iterations. This framework offers a low-cost, memory-efficient tool for static pre-failure stress analysis in granular mechanics. - Open Access
- 6 March 2026
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 206
Seismic response of disconnected piled raft foundation during a strong earthquake based on dynamic centrifuge tests
- 6 March 2026
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 206
Open AccessSeismic response of disconnected piled raft foundation during a strong earthquake based on dynamic centrifuge tests
- Open Access
- 21 September 2025
- Published by Elsevier in Soils and Foundations
- Vol. 65 (6)
Investigation on the lateral performance of new piles in sand sites containing existing piles and shallow cement-treated backfill
- 21 September 2025
- Published by Elsevier in Soils and Foundations
- Vol. 65 (6)
Open AccessInvestigation on the lateral performance of new piles in sand sites containing existing piles and shallow cement-treated backfill
- 1 September 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (9) , 07022024
Closure to “Effects of Pile Tip Support Condition on Pile Behavior under the Action of a Large Earthquake” by Shuji Tamura, Koyo Torii, and Naoki Iriguchi
Sponsored by Geotechnical Engineering
- 1 September 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (9) , 07022024
Closure to “Effects of Pile Tip Support Condition on Pile Behavior under the Action of a Large Earthquake” by Shuji Tamura, Koyo Torii, and Naoki Iriguchi
Sponsored by Geotechnical Engineering
- 1 August 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 147 (8) , 04021065
Effects of Pile Tip Support Condition on Pile Behavior under the Action of a Large Earthquake
Effective methods for evaluating the bending moment of a pile caused by lateral forces at the pile head are available. However, the effects of axial load variation caused by the overturning moment on pile responses have not been investigated in detail. To investigate the effects of pile settlement caused by axial load variations on the pile behavior under a large earthquake, dynamic centrifuge tests on soil–pile–superstructure models were performed. Centrifuge tests showed that the bending moment of the piles depended on the pile-tip support conditions. The test results were examined via numerical analyses using the monotonic beam on nonlinear Winkler foundation (BNWF) method. When the pile tips were supported by vertical springs and rollers, the bending moments at the pile head resulting from the overturning moment increased with the increase in the horizontal subgrade reaction in the subsurface soil. Our findings contribute toward rational seismic design of pile foundations under the action of a large earthquake.
- 1 August 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 147 (8) , 04021065
Effects of Pile Tip Support Condition on Pile Behavior under the Action of a Large Earthquake
Effective methods for evaluating the bending moment of a pile caused by lateral forces at the pile head are available. However, the effects of axial load variation caused by the overturning moment on pile responses have not been investigated in detail. To investigate the effects of pile settlement caused by axial load variations on the pile behavior under a large earthquake, dynamic centrifuge tests on soil–pile–superstructure models were performed. Centrifuge tests showed that the bending moment of the piles depended on the pile-tip support conditions. The test results were examined via numerical analyses using the monotonic beam on nonlinear Winkler foundation (BNWF) method. When the pile tips were supported by vertical springs and rollers, the bending moments at the pile head resulting from the overturning moment increased with the increase in the horizontal subgrade reaction in the subsurface soil. Our findings contribute toward rational seismic design of pile foundations under the action of a large earthquake.
- 1 September 2019
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 124, 268-279
Liquefaction-induced settlement and tilting of buildings with shallow foundations based on field and laboratory observation
- 1 September 2019
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 124, 268-279
Liquefaction-induced settlement and tilting of buildings with shallow foundations based on field and laboratory observation
- Open Access
- 1 August 2019
- Published by Elsevier in Soils and Foundations
- Vol. 59 (4) , 966-981
Stress transfer from rocking shallow foundations on soil-cement reinforced clay
- 1 August 2019
- Published by Elsevier in Soils and Foundations
- Vol. 59 (4) , 966-981
Open AccessStress transfer from rocking shallow foundations on soil-cement reinforced clay
- 1 January 2019
- Published by Japan Association for Earthquake Engineering in Journal of Japan Association for Earthquake Engineering
- Vol. 19 (5) , 5_304-5_310
Shaft Resistance of Piles under Horizontal Force and Overturning Moment
遠心場における押込み載荷実験,鉛直交番載荷実験および転倒モーメントを伴う静的水平交番載荷実験を行い,地震時の変動軸力を受ける杭の周面摩擦力を検討し,以下の知見を得た.転倒モーメントを伴う水平交番載荷における杭の周面摩擦力は,押込み載荷および鉛直交番載荷のそれを明らかに上回った.この傾向は杭の上部で顕著であった.また,水平交番載荷における杭の周面摩擦力は,水平地盤反力に依存して大きくなった.これは,水平地盤反力によって杭の拘束圧が増加したためと考えられる.
- 1 January 2019
- Published by Japan Association for Earthquake Engineering in Journal of Japan Association for Earthquake Engineering
- Vol. 19 (5) , 5_304-5_310
Shaft Resistance of Piles under Horizontal Force and Overturning Moment
遠心場における押込み載荷実験,鉛直交番載荷実験および転倒モーメントを伴う静的水平交番載荷実験を行い,地震時の変動軸力を受ける杭の周面摩擦力を検討し,以下の知見を得た.転倒モーメントを伴う水平交番載荷における杭の周面摩擦力は,押込み載荷および鉛直交番載荷のそれを明らかに上回った.この傾向は杭の上部で顕著であった.また,水平交番載荷における杭の周面摩擦力は,水平地盤反力に依存して大きくなった.これは,水平地盤反力によって杭の拘束圧が増加したためと考えられる.
- 1 November 2018
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 18 (6) , 281-289
A simple method for detecting cracks in soil–cement reinforcement for centrifuge modelling
This paper presents the development, implementation and experimental evaluation of a new crack detection mechanism for centrifuge modelling. The proposed mechanism is a brittle conductor bonded to cement providing a binary indication of if, and when, a sensor is cracked. The results of a pair of large centrifuge tests were used to evaluate the effectiveness of the proposed crack detection mechanism. Each test model included a soil profile consisting of a 23 m thick layer of lightly over-consolidated clay, underlain and overlain by thin layers of dense sand. The centrifuge models had two separate zones, a zone without reinforcement and a zone with an ‘embedded’ soil–cement grid, which had a unit cell area replacement ratio Ar = 24%. Models were subjected to 13 different shaking events with peak base accelerations ranging from 0·01 to 0·55g. The performance of the proposed crack detection mechanism was examined using (i) post-test crack mapping in the soil–cement grids, (ii) results of the crack detection system and (iii) time series of accelerations, displacements and footing rotation. The results from the centrifuge test showed that the proposed crack detection method accurately captured if, and when, cracking occurred in the soil–cement grid at the locations of the sensors.
- 1 November 2018
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 18 (6) , 281-289
A simple method for detecting cracks in soil–cement reinforcement for centrifuge modelling
This paper presents the development, implementation and experimental evaluation of a new crack detection mechanism for centrifuge modelling. The proposed mechanism is a brittle conductor bonded to cement providing a binary indication of if, and when, a sensor is cracked. The results of a pair of large centrifuge tests were used to evaluate the effectiveness of the proposed crack detection mechanism. Each test model included a soil profile consisting of a 23 m thick layer of lightly over-consolidated clay, underlain and overlain by thin layers of dense sand. The centrifuge models had two separate zones, a zone without reinforcement and a zone with an ‘embedded’ soil–cement grid, which had a unit cell area replacement ratio Ar = 24%. Models were subjected to 13 different shaking events with peak base accelerations ranging from 0·01 to 0·55g. The performance of the proposed crack detection mechanism was examined using (i) post-test crack mapping in the soil–cement grids, (ii) results of the crack detection system and (iii) time series of accelerations, displacements and footing rotation. The results from the centrifuge test showed that the proposed crack detection method accurately captured if, and when, cracking occurred in the soil–cement grid at the locations of the sensors.