Mohanchand Paladugu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mohanchand Paladugu has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Chennupati Jagadish
The Australian National University
10 shared publications - Hark Hoe Tan
The Australian National University
10 shared publications - Jin Zou
School of Mechanical and Mining Engineering, and Centre for Microscopy and Microanalysis, The University of Queensland, Brisbane, Australia
10 shared publications - Hannah J. Joyce
University of Cambridge
9 shared publications R. Scott Hyde
The Timken Company World Headquarters 1 , 4500 Mt. Pleasant St NW, North Canton, OH44720, US
9 shared publicationsQiang Gao
The Australian National University 3 Department of Electronic Materials Engineering, Research School of Physical Sciences and Engineering Canberra, Australian Capital Territory 0200, Australia
8 shared publications
Latest Publications
- 1 August 2020
- Published by ASTM International
- p. 182-201
Influence of Material, Heat Treatment, and Microstructure in Resisting White Etching Crack Damage
In this study, steels that had undergone different heat treatments resulting in different microstructures were tested under rolling contact fatigue (RCF) and under specific test conditions known to cause white etching cracks (WECs). The test conditions included high slide-to-roll ratios and a lubricant known to promote WECs. It was observed that case-carburized AISI 3310 steel showed longer fatigue life than martensitically through-hardened 52100 steel with respect to a WEC damage mode. To understand how and why the case-carburized steel showed longer life, other material heat-treated combinations were tested and different material strengthening mechanisms were considered. The study examined carburized steel that had been heat treated differently and RCF tested. The 3310 steel was carburized at a lower carbon potential, and post carburize austenitization was done at a lower temperature so that lesser solute quantities would dissolve into the austenite phase prior to the quench step. The carburized steel samples with less solute dissolution showed higher hardness and more compressive stresses than the original carburized steel; however, they showed 75% shorter RCF life than the original carburized steel. These results suggest that solid solution strengthening is the prime contributor to fatigue resistance under WEC damage conditions. In addition, coarse microstructure morphologies obtained through high austenitization temperatures were shown to exhibit poor WEC damage resistance.
- 1 August 2020
- Published by ASTM International
- p. 182-201
Influence of Material, Heat Treatment, and Microstructure in Resisting White Etching Crack Damage
In this study, steels that had undergone different heat treatments resulting in different microstructures were tested under rolling contact fatigue (RCF) and under specific test conditions known to cause white etching cracks (WECs). The test conditions included high slide-to-roll ratios and a lubricant known to promote WECs. It was observed that case-carburized AISI 3310 steel showed longer fatigue life than martensitically through-hardened 52100 steel with respect to a WEC damage mode. To understand how and why the case-carburized steel showed longer life, other material heat-treated combinations were tested and different material strengthening mechanisms were considered. The study examined carburized steel that had been heat treated differently and RCF tested. The 3310 steel was carburized at a lower carbon potential, and post carburize austenitization was done at a lower temperature so that lesser solute quantities would dissolve into the austenite phase prior to the quench step. The carburized steel samples with less solute dissolution showed higher hardness and more compressive stresses than the original carburized steel; however, they showed 75% shorter RCF life than the original carburized steel. These results suggest that solid solution strengthening is the prime contributor to fatigue resistance under WEC damage conditions. In addition, coarse microstructure morphologies obtained through high austenitization temperatures were shown to exhibit poor WEC damage resistance.
- 1 August 2020
- Published by ASTM International
- p. 131-146
Lubricant-Induced White Etching Cracks: Mechanism and Effects of Surface Finishing
Cylindrical roller thrust bearings (CRTBs) were fatigue tested in various lubricants under rolling-sliding conditions. The bearings exhibited premature damage when the tests were performed in a lubricant containing significant additives (referred to in this paper as “test gear oil”). Bearing life in the test gear oil was less than 5% of bearing life when tested in a mineral oil containing no additives. Investigations on posttest bearings from the test gear oil revealed localized raised areas on the tribosurfaces of the raceways. Upon further examination, subsurface white etching cracks (WECs) were observed beneath the raised surface features. The raised areas resembled hydrogen-induced blisters. Subsequent thermal desorption spectroscopy analysis of the bearing races with the raised features revealed hydrogen evolution from the posttest raceways. In contrast, races exhibited typical point surface origin (PSO)-type damage when the bearings were tested in plain mineral oil. Also, there were no subsurface crack networks or white etching features associated with the PSO spalling damage. Additional tests were performed with embedded abrasive particles that were introduced onto the raceways using a lapping process. Posttest investigations showed neither the raceways nor the rollers contained WECs, and the damage mode had changed even though they were tested in the test gear oil. Although WECs are generated in the subsurface, their formation depends on the surface condition of the raceways, so these results suggest that WEC formation is a surface-driven phenomenon. Based on these insights, possible WEC mitigation and prevention methods are discussed.
- 1 August 2020
- Published by ASTM International
- p. 131-146
Lubricant-Induced White Etching Cracks: Mechanism and Effects of Surface Finishing
Cylindrical roller thrust bearings (CRTBs) were fatigue tested in various lubricants under rolling-sliding conditions. The bearings exhibited premature damage when the tests were performed in a lubricant containing significant additives (referred to in this paper as “test gear oil”). Bearing life in the test gear oil was less than 5% of bearing life when tested in a mineral oil containing no additives. Investigations on posttest bearings from the test gear oil revealed localized raised areas on the tribosurfaces of the raceways. Upon further examination, subsurface white etching cracks (WECs) were observed beneath the raised surface features. The raised areas resembled hydrogen-induced blisters. Subsequent thermal desorption spectroscopy analysis of the bearing races with the raised features revealed hydrogen evolution from the posttest raceways. In contrast, races exhibited typical point surface origin (PSO)-type damage when the bearings were tested in plain mineral oil. Also, there were no subsurface crack networks or white etching features associated with the PSO spalling damage. Additional tests were performed with embedded abrasive particles that were introduced onto the raceways using a lapping process. Posttest investigations showed neither the raceways nor the rollers contained WECs, and the damage mode had changed even though they were tested in the test gear oil. Although WECs are generated in the subsurface, their formation depends on the surface condition of the raceways, so these results suggest that WEC formation is a surface-driven phenomenon. Based on these insights, possible WEC mitigation and prevention methods are discussed.
- 1 June 2019
- Published by Elsevier in Tribology International
- Vol. 134, 232-239
Figure the impact of steel microstructure and heat treatment on the formation of white etching cracks
- 1 June 2019
- Published by Elsevier in Tribology International
- Vol. 134, 232-239
Figure the impact of steel microstructure and heat treatment on the formation of white etching cracks
- 1 March 2017
- Published by Elsevier in Scripta Materialia
- Vol. 130, 219-222
White etching matter promoted by intergranular embrittlement
- 1 March 2017
- Published by Elsevier in Scripta Materialia
- Vol. 130, 219-222
White etching matter promoted by intergranular embrittlement