Lourdes Irusta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lourdes Irusta has a total of 200 co-authors. Here are the top co-authors by number of shared publications:
- Alba González
Polimero eta Material Aurreratuak: Fisika, Kimika eta Teknologia, Kimika Fakultatea, Euskal Herriko Unibertsitatea UPV/EHU, Donostia-San Sebastián, Spain
29 shared publications - Juan José Iruin
University of the Basque Country
17 shared publications M.J. Fernández-Berridi
16 shared publications- Haritz Sardon
POLYMAT, University of the Basque Country UPV/EHU, Donostia-San Sebastian, Spain
15 shared publications - Loli Martin
Macrobehavior-Mesostructure-Nanotechnology, General Research Service (SGIker), Polytechnic School, University of the Basque Country, Plaza Europa 1, 20018 Donostia-San Sebastián, Spain
15 shared publications - Maria Jose Fernandez-Berridi
POLYMAT, Polymer Science and Technology Department, Faculty of Chemistry, University of the Basque Country, UPV/EHU, Donostia, Spain
8 shared publications
Latest Publications
- Open Access
- 26 February 2026
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 227 (4)
Catalyst‐Controlled Dual Dynamic Networks in Polyhydroxyurethanes from Six‐Membered Cyclic Carbonates
External catalysts were used to promote dynamic exchange reactions within polyhydroxyurethanes (PHUs) derived from 6‐membered cyclic carbonates (6CCs). Owing to the presence of both carbamate and ester linkages in the network, two types of covalent exchange reactions; transcarbamoylation and transesterification can occur. A wide variety of catalysts were evaluated for their ability to promote exchange reactions, including dibutyltin dilaurate (DBTDL), potassium methoxide (MeOK), iron(III) acetylacetonate (Fe(acac) 3 ), 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD), 4‐dimethylaminopyridine (DMAP), zinc acetate (ZnOAc) 2 , and bismuth neodecanoate (Bi(neo) 3 ). PHU networks were extensively characterized by thermomechanical analysis (TGA, DSC, DMA, tensile testing), rheological measurements (stress relaxation and small amplitude oscillatory shear), infrared spectroscopy, swelling experiments, and reprocessing tests. Among the catalysts evaluated in this study, the PHU network prepared using potassium methoxide exhibited the best overall performance, combining superior mechanical properties with good reprocessability (up to three cycles), even at a low catalyst loading (2.5 mol%).
- 26 February 2026
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 227 (4)
Open AccessCatalyst‐Controlled Dual Dynamic Networks in Polyhydroxyurethanes from Six‐Membered Cyclic Carbonates
External catalysts were used to promote dynamic exchange reactions within polyhydroxyurethanes (PHUs) derived from 6‐membered cyclic carbonates (6CCs). Owing to the presence of both carbamate and ester linkages in the network, two types of covalent exchange reactions; transcarbamoylation and transesterification can occur. A wide variety of catalysts were evaluated for their ability to promote exchange reactions, including dibutyltin dilaurate (DBTDL), potassium methoxide (MeOK), iron(III) acetylacetonate (Fe(acac) 3 ), 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD), 4‐dimethylaminopyridine (DMAP), zinc acetate (ZnOAc) 2 , and bismuth neodecanoate (Bi(neo) 3 ). PHU networks were extensively characterized by thermomechanical analysis (TGA, DSC, DMA, tensile testing), rheological measurements (stress relaxation and small amplitude oscillatory shear), infrared spectroscopy, swelling experiments, and reprocessing tests. Among the catalysts evaluated in this study, the PHU network prepared using potassium methoxide exhibited the best overall performance, combining superior mechanical properties with good reprocessability (up to three cycles), even at a low catalyst loading (2.5 mol%).
- Open Access
- 7 February 2026
- Published by Elsevier in SSRN Electronic Journal
Development of Flame-Retardant waterborne alkyd resins for wood coating
Phosphorus-containing water-borne alkyd resins were prepared for use as flame-retardant transparent wood coatings. The synthesis process involved alcoholysis followed by esterification, incorporating the reactive flame-retardants polyethyl-phosphate glycol ester (Exolit OP550) and 2-hydroxyethyl methacrylate phosphate (Sartomer 9054). Additionally, different size ammonium polyphosphate additive flame-retardants (Exolit AP422 and Exolit AP423) were incorporated into the base alkyd resin. Chemical characterisation using techniques such as NMR and FTIR confirmed the successful synthesis and the effects of the flame-retardants on the esterification reactions were analysed. Samples containing Santomer 9054 and high amount of Exolit OP550 did not give rise to stable dispersions. SEC analysis revealed changes in molar mass distribution with the incorporation of flame-retardants. Dispersion and film characterisation included particle size measurements, contact angle measurements, and evaluation of thermal properties by DSC and TGA. Evaluation of the formulated films included assessments of fire performance by cone calorimetry, transparency, adhesion to wood substrates, gloss, hardness, and water sensitivity. Flame-retardants had significant effects on fire behaviour, thermal properties, and coating performance, with additive flame-retardants demonstrating higher efficacy than their reactive counterparts.
- 7 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDevelopment of Flame-Retardant waterborne alkyd resins for wood coating
Phosphorus-containing water-borne alkyd resins were prepared for use as flame-retardant transparent wood coatings. The synthesis process involved alcoholysis followed by esterification, incorporating the reactive flame-retardants polyethyl-phosphate glycol ester (Exolit OP550) and 2-hydroxyethyl methacrylate phosphate (Sartomer 9054). Additionally, different size ammonium polyphosphate additive flame-retardants (Exolit AP422 and Exolit AP423) were incorporated into the base alkyd resin. Chemical characterisation using techniques such as NMR and FTIR confirmed the successful synthesis and the effects of the flame-retardants on the esterification reactions were analysed. Samples containing Santomer 9054 and high amount of Exolit OP550 did not give rise to stable dispersions. SEC analysis revealed changes in molar mass distribution with the incorporation of flame-retardants. Dispersion and film characterisation included particle size measurements, contact angle measurements, and evaluation of thermal properties by DSC and TGA. Evaluation of the formulated films included assessments of fire performance by cone calorimetry, transparency, adhesion to wood substrates, gloss, hardness, and water sensitivity. Flame-retardants had significant effects on fire behaviour, thermal properties, and coating performance, with additive flame-retardants demonstrating higher efficacy than their reactive counterparts.
- Open Access
- 22 November 2025
- Published by Wiley in Advanced Materials
- Vol. 38 (51) , e16894
Ammonium Salts as Curing Agents to Obtain Ionic Epoxy Resins With a Thermoplastic‐to‐Thermoset Transition
A new class of epoxy thermosets is presented, prepared using ammonium salts as hardeners, enabling the direct formulation of networks with ionic functionality from simple, industrially available building blocks. The curing process occurs in two distinct thermal stages: the formation of a fusible thermoplastic‐like intermediate, followed by crosslinking into an infusible thermoset. This intermediate behavior is highly unusual in epoxy systems and allows the material to be processed using methods typically applied to thermoplastics, such as extrusion. The practical relevance of this system is demonstrated through the fabrication of enduring prepregs that can be shaped and handled as thermoplastics during processing, but form crosslinked thermosets upon curing. Finally, the cured matrix can be chemically solubilized in aqueous nitric acid under relatively mild conditions, allowing efficient recycling of intact carbon fibers. This work introduces a scalable platform for functional epoxy networks with broad processing and application potential.
- 22 November 2025
- Published by Wiley in Advanced Materials
- Vol. 38 (51) , e16894
Open AccessAmmonium Salts as Curing Agents to Obtain Ionic Epoxy Resins With a Thermoplastic‐to‐Thermoset Transition
A new class of epoxy thermosets is presented, prepared using ammonium salts as hardeners, enabling the direct formulation of networks with ionic functionality from simple, industrially available building blocks. The curing process occurs in two distinct thermal stages: the formation of a fusible thermoplastic‐like intermediate, followed by crosslinking into an infusible thermoset. This intermediate behavior is highly unusual in epoxy systems and allows the material to be processed using methods typically applied to thermoplastics, such as extrusion. The practical relevance of this system is demonstrated through the fabrication of enduring prepregs that can be shaped and handled as thermoplastics during processing, but form crosslinked thermosets upon curing. Finally, the cured matrix can be chemically solubilized in aqueous nitric acid under relatively mild conditions, allowing efficient recycling of intact carbon fibers. This work introduces a scalable platform for functional epoxy networks with broad processing and application potential.
- Open Access
A Review of the Sampling, Analysis, and Identification Techniques of Microplastics in the Air: Insights into PM2.5 and PM10
The massive use of plastics has raised growing environmental concerns, including microplastic (MP) pollution. While most studies have focused on MPs in aquatic environments, research on airborne microplastics has gained increasing attention in recent years. This review discusses the sampling, analytical, and identification techniques used for MPs, with a particular focus on PM2.5 and PM10 fractions, which have been scarcely addressed in the literature. The main active and passive sampling methods, sample preparation protocols, MP quantification approaches, and chemical characterization techniques applied to airborne plastic particles are compiled. Attention is given to the influence of meteorological conditions on transport and deposition, as well as to the predominant sources of primary and secondary microplastics in both indoor and outdoor environments. The analysis identifies the main research challenges, particularly in the detection of microplastics and in the standardization of protocols. The review highlights the need for standardized methodologies to advance reliable quantification and to better understand the environmental implications of MPs.
Open AccessA Review of the Sampling, Analysis, and Identification Techniques of Microplastics in the Air: Insights into PM2.5 and PM10
The massive use of plastics has raised growing environmental concerns, including microplastic (MP) pollution. While most studies have focused on MPs in aquatic environments, research on airborne microplastics has gained increasing attention in recent years. This review discusses the sampling, analytical, and identification techniques used for MPs, with a particular focus on PM2.5 and PM10 fractions, which have been scarcely addressed in the literature. The main active and passive sampling methods, sample preparation protocols, MP quantification approaches, and chemical characterization techniques applied to airborne plastic particles are compiled. Attention is given to the influence of meteorological conditions on transport and deposition, as well as to the predominant sources of primary and secondary microplastics in both indoor and outdoor environments. The analysis identifies the main research challenges, particularly in the detection of microplastics and in the standardization of protocols. The review highlights the need for standardized methodologies to advance reliable quantification and to better understand the environmental implications of MPs.
- Open Access
- 6 August 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (33) , 30095-30106
A Material Platform Based on Dissociative CO2-Derived N,O-Acetals for Tunable Degradation of 3D Printable Materials
Modern-day thermosetting polymers should be designed with circular economy principles in mind, considering both their recyclability and end-of-life options. Covalent adaptable networks (CANs) have the potential to address the environmental challenges we face today as, in spite of being thermosets, they can be reprocessed by conventional thermoprocessing methods and are thus recyclable. While in the last years intensive efforts have been devoted to the preparation of CANs using sustainable sources, less attention has been paid to their end-of-life options in case they escape from plastic sorting. Herein, we report the development of a new type of dynamic bond, the N,O-acetal bond based on the coupling between CO2-based oxazolidone moieties and abundant, potentially biobased polyols. Computational and kinetic studies revealed that this bond underwent rapid dissociative exchange and, crucially, was also susceptible to hydrolytic degradation. We then prepared a range of thermoset materials endowed by double end-of-life features, i.e., CAN behavior and hydrolytic degradation. This was achieved by radical thiol-ene photo-cross-linking of a diallyl monomer bearing the N,O-acetal moiety with another alkene-functionalized monomer that did not bear this dynamic bond. CANs with tunable mechanical properties and hydrolytic degradation features were easily obtained by modulating the monomer compositions. The fast-photocuring of the N,O-functionalized monomer was then exploited for producing three-dimensional (3D) printed objects, offering the potential for on-demand hydrolytic behavior.
- 6 August 2025
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 147 (33) , 30095-30106
Open AccessA Material Platform Based on Dissociative CO2-Derived N,O-Acetals for Tunable Degradation of 3D Printable Materials
Modern-day thermosetting polymers should be designed with circular economy principles in mind, considering both their recyclability and end-of-life options. Covalent adaptable networks (CANs) have the potential to address the environmental challenges we face today as, in spite of being thermosets, they can be reprocessed by conventional thermoprocessing methods and are thus recyclable. While in the last years intensive efforts have been devoted to the preparation of CANs using sustainable sources, less attention has been paid to their end-of-life options in case they escape from plastic sorting. Herein, we report the development of a new type of dynamic bond, the N,O-acetal bond based on the coupling between CO2-based oxazolidone moieties and abundant, potentially biobased polyols. Computational and kinetic studies revealed that this bond underwent rapid dissociative exchange and, crucially, was also susceptible to hydrolytic degradation. We then prepared a range of thermoset materials endowed by double end-of-life features, i.e., CAN behavior and hydrolytic degradation. This was achieved by radical thiol-ene photo-cross-linking of a diallyl monomer bearing the N,O-acetal moiety with another alkene-functionalized monomer that did not bear this dynamic bond. CANs with tunable mechanical properties and hydrolytic degradation features were easily obtained by modulating the monomer compositions. The fast-photocuring of the N,O-functionalized monomer was then exploited for producing three-dimensional (3D) printed objects, offering the potential for on-demand hydrolytic behavior.
- Open Access
- 6 August 2025
- Published by Royal Society of Chemistry (RSC) in RSC Sustainability
- Vol. 3 (10) , 4622-4631
Mechanical, barrier, and photodegradation properties of biodegradable PLA-based blend films
In this work, films based on blends of polylactide (PLA), poly(ε-caprolactone), (PCL), and the compatibilizer ElvaloyPTW were prepared by blown film extrusion; neat PLA was used as a reference material. Adding 30% PCL to PLA resulted in films with decreased modulus, yield strength, and tear resistance. However, when ElvaloyPTW was added to the 70/30 PLA/PCL blend, films featuring high ductility and improved gas barrier properties were achieved. The photodegradation of blown films based on PLA/PCL (100/0/0 and 70/30/0 wt%) and PLA/PCL/c (c = compatibilizer (ElvaloyPTW), 70/30/3 wt%) blends was comprehensively investigated under accelerated conditions using a xenon arc lamp for up to 168 h of UV irradiation. The photo-degraded samples were characterized using gel permeation chromatography (GPC), 1H-NMR, FTIR-ATR, thermogravimetric analysis (TGA), polarized light optical microscopy (PLOM), and differential scanning calorimetry (DSC). The results indicate that the photodegradation of PLA/PCL/c films proceeds via a bulk erosion mechanism. This suggests that UV penetrates the specimens with no significant reduction in intensity, irrespective of the polymer blends' chemical structure and crystallinity. PLA and PCL chains were susceptible to photodegradation even within the crystalline regions; however, their photodegradability was lower in the crystals than in the amorphous regions. A significant decrease in molecular weight was observed with photodegradation time. The combined results of FTIR and thermal analysis allowed us to establish that the PLA phase in the blends experiences a much faster degradation rate in the presence of PCL and/or PCL/compatibilizer. Finally, the effect of photodegradation increased the crystallization rate of PLA and affected the morphology of PLA spherulites.
- 6 August 2025
- Published by Royal Society of Chemistry (RSC) in RSC Sustainability
- Vol. 3 (10) , 4622-4631
Open AccessMechanical, barrier, and photodegradation properties of biodegradable PLA-based blend films
In this work, films based on blends of polylactide (PLA), poly(ε-caprolactone), (PCL), and the compatibilizer ElvaloyPTW were prepared by blown film extrusion; neat PLA was used as a reference material. Adding 30% PCL to PLA resulted in films with decreased modulus, yield strength, and tear resistance. However, when ElvaloyPTW was added to the 70/30 PLA/PCL blend, films featuring high ductility and improved gas barrier properties were achieved. The photodegradation of blown films based on PLA/PCL (100/0/0 and 70/30/0 wt%) and PLA/PCL/c (c = compatibilizer (ElvaloyPTW), 70/30/3 wt%) blends was comprehensively investigated under accelerated conditions using a xenon arc lamp for up to 168 h of UV irradiation. The photo-degraded samples were characterized using gel permeation chromatography (GPC), 1H-NMR, FTIR-ATR, thermogravimetric analysis (TGA), polarized light optical microscopy (PLOM), and differential scanning calorimetry (DSC). The results indicate that the photodegradation of PLA/PCL/c films proceeds via a bulk erosion mechanism. This suggests that UV penetrates the specimens with no significant reduction in intensity, irrespective of the polymer blends' chemical structure and crystallinity. PLA and PCL chains were susceptible to photodegradation even within the crystalline regions; however, their photodegradability was lower in the crystals than in the amorphous regions. A significant decrease in molecular weight was observed with photodegradation time. The combined results of FTIR and thermal analysis allowed us to establish that the PLA phase in the blends experiences a much faster degradation rate in the presence of PCL and/or PCL/compatibilizer. Finally, the effect of photodegradation increased the crystallization rate of PLA and affected the morphology of PLA spherulites.
- Open Access
- 15 June 2025
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 310 (10)
Recycling of Epoxy Resin via Blending with Polycaprolactone for Fused Filament Fabrication 3D Printing Applications
As a way of recycling epoxy thermoset materials, they were blended with polycaprolactone (PCL) and processed in the form of filament to be used for fused deposition modeling (FDM) 3D printing. Three different epoxy materials were considered: a lab‐cured epoxy resin, a lab‐cured epoxy/PCL blend, and a commercial epoxy composite containing fiberglass (FR4). These three thermosets were milled and mixed with pure PCL. The distribution of the epoxy in the PCL matrix was analyzed by Fourier Transform Infrared Spectroscopy (FTIR) coupled to a microscope. The filler FR4 and DGEBA were adequately distributed in the matrix. The rheological study anticipated good adhesion between the layers, without clogging at printing temperatures. The rheological model also predicted filament buckling. Because of that, external assistance (PLA) was required to obtain appropriate printed samples, avoiding buckling. The mechanical properties of the specimens were determined by tensile tests and compared with injection molded specimens. It was observed that the incorporation of the epoxy thermoset to the PCL matrix enhanced Young's modulus of PCL. Very similar results were obtained between 3D printed and injected samples. The proposed method could be of significant interest in employing thermoset epoxy waste as a cost‐effective reinforcement for fuse filament 3D printing materials.
- 15 June 2025
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 310 (10)
Open AccessRecycling of Epoxy Resin via Blending with Polycaprolactone for Fused Filament Fabrication 3D Printing Applications
As a way of recycling epoxy thermoset materials, they were blended with polycaprolactone (PCL) and processed in the form of filament to be used for fused deposition modeling (FDM) 3D printing. Three different epoxy materials were considered: a lab‐cured epoxy resin, a lab‐cured epoxy/PCL blend, and a commercial epoxy composite containing fiberglass (FR4). These three thermosets were milled and mixed with pure PCL. The distribution of the epoxy in the PCL matrix was analyzed by Fourier Transform Infrared Spectroscopy (FTIR) coupled to a microscope. The filler FR4 and DGEBA were adequately distributed in the matrix. The rheological study anticipated good adhesion between the layers, without clogging at printing temperatures. The rheological model also predicted filament buckling. Because of that, external assistance (PLA) was required to obtain appropriate printed samples, avoiding buckling. The mechanical properties of the specimens were determined by tensile tests and compared with injection molded specimens. It was observed that the incorporation of the epoxy thermoset to the PCL matrix enhanced Young's modulus of PCL. Very similar results were obtained between 3D printed and injected samples. The proposed method could be of significant interest in employing thermoset epoxy waste as a cost‐effective reinforcement for fuse filament 3D printing materials.
- Open Access
Comparative Life Cycle Assessment of Recyclable Polyhydroxyurethanes Synthesized from Five- and Six-Membered Carbonates
Polyhydroxyurethanes (PHUs) synthesized from cyclic carbonates are promising alternatives to conventional polyurethanes due to their advantageous isocyanate-free synthesis and reprocessability characteristics. While many studies focus on PHUs derived from five-membered cyclic carbonates (5CCs) for more sustainable synthesis routes, PHUs from six-membered cyclic carbonates (6CCs) exhibit enhanced reactivity towards amines. Their reprocessability is facilitated by the presence of hydroxyl groups along the polymer chain, enabling transcarbamoylation reactions. However, since non-catalyzed transcarbamoylation is typically a sluggish reaction, catalysts are often required to enhance network reprocessability. This study presents a life cycle assessment (LCA) of PHU-5CC and PHU-6CC syntheses, with catalysts, for recycling applications targeting end-of-life scenarios. Environmental impact categories, including climate change, particulate matter, fossil resource depletion, mineral and metal resource use and freshwater eutrophication, were evaluated. Sensitivity analyses were also conducted to assess key variables. Our results indicate that PHUs from 6CCs show a higher environmental footprint due to their solvent-intensive synthesis process. Despite the increased reactivity and shorter reaction times associated with the 6CC monomer, these benefits do not fully offset the environmental impacts of the synthesis process. In conclusion, this study highlights potential improvements for future PHU synthesis, such as solvent-free processes, metal-free catalysts and optimized reaction monitoring.
Open AccessComparative Life Cycle Assessment of Recyclable Polyhydroxyurethanes Synthesized from Five- and Six-Membered Carbonates
Polyhydroxyurethanes (PHUs) synthesized from cyclic carbonates are promising alternatives to conventional polyurethanes due to their advantageous isocyanate-free synthesis and reprocessability characteristics. While many studies focus on PHUs derived from five-membered cyclic carbonates (5CCs) for more sustainable synthesis routes, PHUs from six-membered cyclic carbonates (6CCs) exhibit enhanced reactivity towards amines. Their reprocessability is facilitated by the presence of hydroxyl groups along the polymer chain, enabling transcarbamoylation reactions. However, since non-catalyzed transcarbamoylation is typically a sluggish reaction, catalysts are often required to enhance network reprocessability. This study presents a life cycle assessment (LCA) of PHU-5CC and PHU-6CC syntheses, with catalysts, for recycling applications targeting end-of-life scenarios. Environmental impact categories, including climate change, particulate matter, fossil resource depletion, mineral and metal resource use and freshwater eutrophication, were evaluated. Sensitivity analyses were also conducted to assess key variables. Our results indicate that PHUs from 6CCs show a higher environmental footprint due to their solvent-intensive synthesis process. Despite the increased reactivity and shorter reaction times associated with the 6CC monomer, these benefits do not fully offset the environmental impacts of the synthesis process. In conclusion, this study highlights potential improvements for future PHU synthesis, such as solvent-free processes, metal-free catalysts and optimized reaction monitoring.
- Open Access
- 2 March 2025
- Published by Wiley in Advanced Materials
- Vol. 37 (15) , e2417355
Fully Recyclable Pluripotent Networks for 3D Printing Enabled by Dissociative Dynamic Bonds
Additive manufacturing (AM) has risen in popularity due to its ability to produce complex shapes in a material‐efficient way. However, to produce objects with advanced properties, complex multimaterial strategies are often employed. This one‐polymer‐one‐property paradigm significantly slows down the application of AM, and in particular of fused deposition modeling (FDM), for manufacturing of functional objects. In this study advantage of pluripotency in materials is taken, i.e., the ability to attain different properties from a single stock, to afford mechanically tunable 3D printed dynamic thermosets (moduli from 2 MPa – 3 GPa, 1500× increase, Stress at break from 2 to 70 MPa, 35× increase). To do so, FDM‐compatible CO 2 ‐derived dissociative polymer networks are designed that undergo a dynamic reaction‐induced phase‐separation (DRIPS). This strategy enables the control of the size of the rigid phase with a simple post‐printing thermal treatment, cascading in spatially patterned mechanical properties. This study showcases new directions for the 3D printing communities, with deep implications in soft robotics and compliant mechanics.
- 2 March 2025
- Published by Wiley in Advanced Materials
- Vol. 37 (15) , e2417355
Open AccessFully Recyclable Pluripotent Networks for 3D Printing Enabled by Dissociative Dynamic Bonds
Additive manufacturing (AM) has risen in popularity due to its ability to produce complex shapes in a material‐efficient way. However, to produce objects with advanced properties, complex multimaterial strategies are often employed. This one‐polymer‐one‐property paradigm significantly slows down the application of AM, and in particular of fused deposition modeling (FDM), for manufacturing of functional objects. In this study advantage of pluripotency in materials is taken, i.e., the ability to attain different properties from a single stock, to afford mechanically tunable 3D printed dynamic thermosets (moduli from 2 MPa – 3 GPa, 1500× increase, Stress at break from 2 to 70 MPa, 35× increase). To do so, FDM‐compatible CO 2 ‐derived dissociative polymer networks are designed that undergo a dynamic reaction‐induced phase‐separation (DRIPS). This strategy enables the control of the size of the rigid phase with a simple post‐printing thermal treatment, cascading in spatially patterned mechanical properties. This study showcases new directions for the 3D printing communities, with deep implications in soft robotics and compliant mechanics.