Yui-Chuin Shiah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yui-Chuin Shiah has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Rahim Hematiyan
Department of Mechanical Engineering, Shiraz University, Shiraz, Iran
13 shared publications - Amir Khosravifard
Department of Mechanical Engineering, Shiraz University, Shiraz, Iran
4 shared publications - Yu-Jen Chen
Southern Taiwan University of Science and Technology
4 shared publications Chyanbin Hwu
3 shared publications- Choon-Lai Tan
Department of Mechanical and Aerospace Engineering, Carleton University, 1125 Colonel By Drive, Ottawa, ON, K1S 5B6, Canada
2 shared publications - Chung-Lei Hsu2 shared publications
Latest Publications
- 10 December 2025
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 183
BEM simulation of the interlaminar stresses of 3D thin composites subjected to inertial loads
- 10 December 2025
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 183
BEM simulation of the interlaminar stresses of 3D thin composites subjected to inertial loads
- 29 September 2025
- Published by Taylor & Francis in Journal of Thermal Stresses
- Vol. 49 (1) , 129-145
Boundary element analysis of thermal stresses on voids/holes in an infinite/semi-infinite anisotropic plane
- 29 September 2025
- Published by Taylor & Francis in Journal of Thermal Stresses
- Vol. 49 (1) , 129-145
Boundary element analysis of thermal stresses on voids/holes in an infinite/semi-infinite anisotropic plane
- 26 December 2024
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 171
Identification of elastic edge parameters of plates using the method of fundamental solutions
- 26 December 2024
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 171
Identification of elastic edge parameters of plates using the method of fundamental solutions
- 30 October 2024
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 169
An efficient scheme of calculating nearly singular integrals for the 3D BEM modeling of thin media
- 30 October 2024
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 169
An efficient scheme of calculating nearly singular integrals for the 3D BEM modeling of thin media
- Open Access
- 27 December 2023
- Published by Springer Nature in Research Square
An Inverse Boundary-Type Meshfree Method for Identification of 2D Elastic Properties of Anisotropic Solids
There are six elastic constants for an anisotropic body in plane strain/stress conditions. In the inverse problem of this study, it is assumed that the elastic constants of an anisotropic body are unknown, while the displacements or strains at several sampling points of the body under static loading are provided. For the first time, a boundary-type meshfree method, i.e. the method of fundamental solutions, is used for solving the problem, where the sensitivity analysis is performed by direct differentiation of the discretized equations. For that, the closed-form relations for sensitivity of the displacements/strains with respect to the elastic constants are analytically derived. Using a numerical study, it is shown that the proposed sensitivity analysis is much more advantageous compared to traditional finite difference approximation. A simple method for proper selection of initial guesses is also proposed. Two different example problems under plane strain and plane stress conditions are provided to investigate the accuracy of the proposed inverse method. Moreover, the effects of the number of measurement data, the measurement error, and the configuration of sampling points on the solution of the inverse problem are studied. It is observed that the solutions are more accurate in the cases where the sampling points are located at different parts of the body.
- 27 December 2023
- Published by Springer Nature in Research Square
Open AccessAn Inverse Boundary-Type Meshfree Method for Identification of 2D Elastic Properties of Anisotropic Solids
There are six elastic constants for an anisotropic body in plane strain/stress conditions. In the inverse problem of this study, it is assumed that the elastic constants of an anisotropic body are unknown, while the displacements or strains at several sampling points of the body under static loading are provided. For the first time, a boundary-type meshfree method, i.e. the method of fundamental solutions, is used for solving the problem, where the sensitivity analysis is performed by direct differentiation of the discretized equations. For that, the closed-form relations for sensitivity of the displacements/strains with respect to the elastic constants are analytically derived. Using a numerical study, it is shown that the proposed sensitivity analysis is much more advantageous compared to traditional finite difference approximation. A simple method for proper selection of initial guesses is also proposed. Two different example problems under plane strain and plane stress conditions are provided to investigate the accuracy of the proposed inverse method. Moreover, the effects of the number of measurement data, the measurement error, and the configuration of sampling points on the solution of the inverse problem are studied. It is observed that the solutions are more accurate in the cases where the sampling points are located at different parts of the body.
- Open Access
Efficient BEM Modeling of the Heat Transfer in the Turbine Blades of Aero-Parts
The modeling of the turbine blades in aero-parts presents difficulties in conventional domain solution techniques, especially when internal cooling air passages and a thermal barrier coating (TBC) are applied. This paper presents a very efficient 3D modeling of the anisotropic heat conduction in turbine blades with the boundary element method (BEM), where both the TBC and cooling air passages are considered. The BEM is very ideal for this modeling, since only boundary meshes are required for it; however, a serious problem of nearly singular integration will arise in modeling with coarse meshes. In this article, an efficient modeling and computational algorithm using the BEM is applied for the simulation of heat conduction in the turbine blades of aero-parts. The present work proposes a simplified BEM model to replace multiple thin coating layers on the top of the blade. In the end, the veracity of the implemented BEM code as well as its computational efficiency are illustrated with a few examples, showing that the settled temperature on the substrate can be reduced by 20% by employing a TBC. As compared to the analyses with ANSYS, the percentages of difference were within 2%, while the CPU time spent by the BEM algorithm was about 1/8 of that of ANSYS, not to mention the meshing efforts saved by adopting by a treatment of equivalent convection.
Open AccessEfficient BEM Modeling of the Heat Transfer in the Turbine Blades of Aero-Parts
The modeling of the turbine blades in aero-parts presents difficulties in conventional domain solution techniques, especially when internal cooling air passages and a thermal barrier coating (TBC) are applied. This paper presents a very efficient 3D modeling of the anisotropic heat conduction in turbine blades with the boundary element method (BEM), where both the TBC and cooling air passages are considered. The BEM is very ideal for this modeling, since only boundary meshes are required for it; however, a serious problem of nearly singular integration will arise in modeling with coarse meshes. In this article, an efficient modeling and computational algorithm using the BEM is applied for the simulation of heat conduction in the turbine blades of aero-parts. The present work proposes a simplified BEM model to replace multiple thin coating layers on the top of the blade. In the end, the veracity of the implemented BEM code as well as its computational efficiency are illustrated with a few examples, showing that the settled temperature on the substrate can be reduced by 20% by employing a TBC. As compared to the analyses with ANSYS, the percentages of difference were within 2%, while the CPU time spent by the BEM algorithm was about 1/8 of that of ANSYS, not to mention the meshing efforts saved by adopting by a treatment of equivalent convection.
- Open Access
Identification of Time Variations of Moving Loads Applied to Plates Resting on Viscoelastic Foundation Using a Meshfree Method
Dynamic identification of the intensity of the moving loads applied to structures is an important task in aerospace, marine, and transportation industries. In the present work, a general technique is presented for identification of the time variations in moving loads applied to plate structures resting on viscoelastic foundation. The identification problem is formulated as an inverse problem, which utilizes dynamic responses. The direct analyses required for the identification problem are performed by a meshfree method based on the moving node technique. In this technique, a node, which travels with the applied force, is utilized in the meshfree method. Since there is no connectivity between the nodes of meshfree methods, this technique can be implemented easily, while reducing the computational labor. Another benefit of this technique is that any simple or complicated trajectory of the moving load can be handled without any additional concerns. Two numerical example problems are solved and the effects of several parameters, including the measurement error, and number of sensors on the accuracy of the results are investigated. Through the examples, it is shown that the presented technique can identify the time variations in moving loads efficiently and accurately.
Open AccessIdentification of Time Variations of Moving Loads Applied to Plates Resting on Viscoelastic Foundation Using a Meshfree Method
Dynamic identification of the intensity of the moving loads applied to structures is an important task in aerospace, marine, and transportation industries. In the present work, a general technique is presented for identification of the time variations in moving loads applied to plate structures resting on viscoelastic foundation. The identification problem is formulated as an inverse problem, which utilizes dynamic responses. The direct analyses required for the identification problem are performed by a meshfree method based on the moving node technique. In this technique, a node, which travels with the applied force, is utilized in the meshfree method. Since there is no connectivity between the nodes of meshfree methods, this technique can be implemented easily, while reducing the computational labor. Another benefit of this technique is that any simple or complicated trajectory of the moving load can be handled without any additional concerns. Two numerical example problems are solved and the effects of several parameters, including the measurement error, and number of sensors on the accuracy of the results are investigated. Through the examples, it is shown that the presented technique can identify the time variations in moving loads efficiently and accurately.