Yu-Jen Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yu-Jen Chen has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Yui-Chuin Shiah
Natl Cheng Kung Univ, Dept Aeronaut & Astronaut, Tainan 701, Taiwan
4 shared publications - Guo-Yuan Huang
National Chung-Shan Institute of Science and Technology Aeronautical Systems Research Division
2 shared publications - Wen Tong Chong
Department of Mechanical Engineering, Faculty of Engineering, Universiti Malaya, Kuala Lumpur 50603, Malaysia
2 shared publications Ankam Vinod Kumar Reddy
Department of Aeronautics and Astronautics, National Cheng Kung University, Tainan, Taiwan, Republic of China
1 shared publicationChang-Chi Huang
1 shared publicationChi-Jeng Bai
1 shared publication
Latest Publications
- 18 June 2025
- Published by Springer Nature
- p. 3-10
Experimental and Research Analysis of Aerodynamic Noise in Small Horizontal-Axis Wind Turbine Blades
- 18 June 2025
- Published by Springer Nature
- p. 3-10
Experimental and Research Analysis of Aerodynamic Noise in Small Horizontal-Axis Wind Turbine Blades
- 31 July 2024
- Published by Springer Nature
- p. 23-30
Stall Effect Applied to Blade of Design and Experiment on Small Horizontal Axis Wind Turbine
- 31 July 2024
- Published by Springer Nature
- p. 23-30
Stall Effect Applied to Blade of Design and Experiment on Small Horizontal Axis Wind Turbine
- Open Access
- 30 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (13) , 7763
Intelligent Machinery Fault Diagnosis Method Based on Adaptive Deep Convolutional Neural Network: Using Dental Milling Cutter Malfunction Classifications as an Example
Intelligent machinery fault diagnosis is one of the key technologies for the transformation and competitiveness of traditional factories. Complex production environments make it difficult to maintain good prediction performance using traditional methods. This paper proposes a deep convolutional neural network combined with an adaptive environmental noise method to achieve robust fault classification. The proposed method uses six-dimensional physical signals for data fusion and feature fusion, extracts obvious features and enhances subtle features, and uses continuous wavelets and Gramian angular fields to transform signals with different physical and frequency characteristics into time–frequency maps and two-dimensional images. The fusion technology of different signals can provide comprehensive features for fault prediction, improving upon the blind spots of traditional methods to extract features, and then perform prediction and classification through deep convolutional neural networks. In the experiment, the tool failure classification of the dental milling machine is used as a verification case. The results show that the prediction accuracy of the proposed method is nearly 100%, much better than other comparison methods. In addition, white noise was added in the experiment to verify the noise immunity of the model. The results show that the accuracy of the proposed method is 99%, which is better than other comparison methods in terms of accuracy and robustness, proving the effectiveness of the proposed method for fault diagnosis and classification.
- 30 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (13) , 7763
Open AccessIntelligent Machinery Fault Diagnosis Method Based on Adaptive Deep Convolutional Neural Network: Using Dental Milling Cutter Malfunction Classifications as an Example
Intelligent machinery fault diagnosis is one of the key technologies for the transformation and competitiveness of traditional factories. Complex production environments make it difficult to maintain good prediction performance using traditional methods. This paper proposes a deep convolutional neural network combined with an adaptive environmental noise method to achieve robust fault classification. The proposed method uses six-dimensional physical signals for data fusion and feature fusion, extracts obvious features and enhances subtle features, and uses continuous wavelets and Gramian angular fields to transform signals with different physical and frequency characteristics into time–frequency maps and two-dimensional images. The fusion technology of different signals can provide comprehensive features for fault prediction, improving upon the blind spots of traditional methods to extract features, and then perform prediction and classification through deep convolutional neural networks. In the experiment, the tool failure classification of the dental milling machine is used as a verification case. The results show that the prediction accuracy of the proposed method is nearly 100%, much better than other comparison methods. In addition, white noise was added in the experiment to verify the noise immunity of the model. The results show that the accuracy of the proposed method is 99%, which is better than other comparison methods in terms of accuracy and robustness, proving the effectiveness of the proposed method for fault diagnosis and classification.
- Open Access
- 3 December 2020
- Published by Oxford University Press (OUP) in Journal of Mechanics
- Vol. 37, 63-71
Canard optimization for enhancing the performance of small horizontal axis wind turbine at low wind speeds
Generally, the environmental wind speeds in urban areas are relatively low due to clustered buildings. At low wind speeds, an aerodynamic stall occurs near the blade roots of a horizontal axis wind turbine (HAWT), leading to decay of the power coefficient. The research targets to design canards with optimal parameters for a small-scale HAWT system operated at variable rotational speeds. The design was to enhance the performance by delaying the aerodynamic stall near blade roots of the HAWT to be operated at low wind speeds. For the optimal design of canards, flow fields of the sample blades with and without canards were both simulated and compared with the experimental data. With the verification of our simulations, Taguchi analyses were performed to seek the optimum parameters of canards. This study revealed that the peak performance of the optimized canard system operated at 540 rpm might be improved by ∼35%.
- 3 December 2020
- Published by Oxford University Press (OUP) in Journal of Mechanics
- Vol. 37, 63-71
Open AccessCanard optimization for enhancing the performance of small horizontal axis wind turbine at low wind speeds
Generally, the environmental wind speeds in urban areas are relatively low due to clustered buildings. At low wind speeds, an aerodynamic stall occurs near the blade roots of a horizontal axis wind turbine (HAWT), leading to decay of the power coefficient. The research targets to design canards with optimal parameters for a small-scale HAWT system operated at variable rotational speeds. The design was to enhance the performance by delaying the aerodynamic stall near blade roots of the HAWT to be operated at low wind speeds. For the optimal design of canards, flow fields of the sample blades with and without canards were both simulated and compared with the experimental data. With the verification of our simulations, Taguchi analyses were performed to seek the optimum parameters of canards. This study revealed that the peak performance of the optimized canard system operated at 540 rpm might be improved by ∼35%.
- 30 September 2020
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 46 (1) , 433-440
Theoretical investigation of the power curve of small HAWT by combining aerodynamic and mechatronic systems
In this paper, a dynamic model is presented to analytically evaluate the power performance of small horizontal axis wind turbine (HAWT) by integrating all related theories in aerodynamics and mechatronics. This model is implemented into a computer program for predicting the output torque and power performance curve of small HAWT. In this implemented program, all pertinent formulations in the blade momentum theory (BEMT) and the Fleming's rule are combined together. For verifying the model, a small HAWT (rated 400 W) using an axial flux permanent magnet (AFPM) generator was experimented in a full‐scale wind tunnel. For a field test, the prototype was installed in National Penghu University International Small‐Medium Wind Turbine Site to collect data at various wind speeds in a whole month. The collected data turned out to agree with our prediction using the proposed model. In designing small HAWT, this model not only expedites the development process but also ensures safe operation of the complete system.
- 30 September 2020
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 46 (1) , 433-440
Theoretical investigation of the power curve of small HAWT by combining aerodynamic and mechatronic systems
In this paper, a dynamic model is presented to analytically evaluate the power performance of small horizontal axis wind turbine (HAWT) by integrating all related theories in aerodynamics and mechatronics. This model is implemented into a computer program for predicting the output torque and power performance curve of small HAWT. In this implemented program, all pertinent formulations in the blade momentum theory (BEMT) and the Fleming's rule are combined together. For verifying the model, a small HAWT (rated 400 W) using an axial flux permanent magnet (AFPM) generator was experimented in a full‐scale wind tunnel. For a field test, the prototype was installed in National Penghu University International Small‐Medium Wind Turbine Site to collect data at various wind speeds in a whole month. The collected data turned out to agree with our prediction using the proposed model. In designing small HAWT, this model not only expedites the development process but also ensures safe operation of the complete system.
- Open Access
Experiments on the Performance of Small Horizontal Axis Wind Turbine with Passive Pitch Control by Disk Pulley
The present work is to design a passive pitch-control mechanism for small horizontal axis wind turbine (HAWT) to generate stable power at high wind speeds. The mechanism uses a disk pulley as an actuator to passively adjust the pitch angle of blades by centrifugal force. For this design, aerodynamic braking is caused by the adjustment of pitch angles at high wind speeds. As a marked advantage, this does not require mechanical brakes that would incur electrical burn-out and structural failure under high speed rotation. This can ensure the survival of blades and generator in sever operation environments. In this paper, the analysis uses blade element momentum theory (BEMT) to develop graphical user interface software to facilitate the performance assessment of the small-scale HAWT using passive pitch control (PPC). For verification, the HAWT system was tested in a full-scale wind tunnel for its aerodynamic performance. At low wind speeds, this system performed the same as usual, yet at high wind speeds, the equipped PPC system can effectively reduce the rotational speed to generate stable power.
Open AccessExperiments on the Performance of Small Horizontal Axis Wind Turbine with Passive Pitch Control by Disk Pulley
The present work is to design a passive pitch-control mechanism for small horizontal axis wind turbine (HAWT) to generate stable power at high wind speeds. The mechanism uses a disk pulley as an actuator to passively adjust the pitch angle of blades by centrifugal force. For this design, aerodynamic braking is caused by the adjustment of pitch angles at high wind speeds. As a marked advantage, this does not require mechanical brakes that would incur electrical burn-out and structural failure under high speed rotation. This can ensure the survival of blades and generator in sever operation environments. In this paper, the analysis uses blade element momentum theory (BEMT) to develop graphical user interface software to facilitate the performance assessment of the small-scale HAWT using passive pitch control (PPC). For verification, the HAWT system was tested in a full-scale wind tunnel for its aerodynamic performance. At low wind speeds, this system performed the same as usual, yet at high wind speeds, the equipped PPC system can effectively reduce the rotational speed to generate stable power.