Aydin Ilker Karsilayan
Research Subjects
Research Interests
Aydin Ilker Karsilayan has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Jose Silva-Martinez
Texas A&M University
6 shared publications Christopher T. Rodenbeck
U.S. Naval Research Laboratory, Washington, DC, USA
2 shared publications- Jian Shao
Department of Electrical and Computer Engineering, Texas AM University, College Station, TX, USA
2 shared publications - Brian B. Tierney
U.S. Naval Research Laboratory, Washington, DC, USA
1 shared publication Christopher Rodenbeck
U.S. Naval Research Laboratory, Washington, DC, USA
1 shared publication- Christopher T. Rodenbeck
Naval Research Laboratory
1 shared publication
Latest Publications
- Open Access
- 16 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 6792-6801
X-Band CMOS Rectifier With 4% Efficiency at −35 dBm for Wireless Power Transmission
This paper proposes a radio frequency (RF) rectifier topology for low-power wireless power transmission (WPT) applications in the X band. The rectifier consists of a biased PMOS pair and is matched to the RF signal source impedance using a PCB transmission line (TL) matching network. It is demonstrated that a clever optimization of the bias voltage enables the rectifier to achieve greater sensitivity and efficiency than previous works at X band. The rectifier was designed in a 45nm silicon-on-insulator (SOI) process and operates at a frequency of 9.64 GHz. It achieves a power conversion efficiency (PCE) of 4% and 46% at power levels of –35 dBm and –10 dBm, respectively.
- 16 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 6792-6801
Open AccessX-Band CMOS Rectifier With 4% Efficiency at −35 dBm for Wireless Power Transmission
This paper proposes a radio frequency (RF) rectifier topology for low-power wireless power transmission (WPT) applications in the X band. The rectifier consists of a biased PMOS pair and is matched to the RF signal source impedance using a PCB transmission line (TL) matching network. It is demonstrated that a clever optimization of the bias voltage enables the rectifier to achieve greater sensitivity and efficiency than previous works at X band. The rectifier was designed in a 45nm silicon-on-insulator (SOI) process and operates at a frequency of 9.64 GHz. It achieves a power conversion efficiency (PCE) of 4% and 46% at power levels of –35 dBm and –10 dBm, respectively.
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 69 (1) , 415-427
An Interference-Tolerant Synchronization Scheme for Wireless Communication Systems Based on Direct Sequence Spread Spectrum
In this paper, an interference-tolerant three-level synchronization scheme for wireless communication systems based on Direct Sequence Spread Spectrum (DSSS) is presented. Although the proposed synchronization scheme is demonstrated in a mixed signal IC solution, it is exportable to fully digital realizations. The proposed technique synchronizes the received pseudo-random sequence (PRS) modulated signal with the receiver (RX) reference PRS by making use of its autocorrelation properties. The proposed scheme employs 3 levels that make the proposed scheme tolerant to strong in-band interferences. Experimental results for the prototype demonstrate the capabilities of the proposed approach to achieve over 50% of clock cycle tracking even in the presence of interferences with a power of 5dB higher than the desired signal power. Fabricated in a mainstream 40nm CMOS technology, the synchronization scheme employs 100MHz PRS at TX and RX; the proposed solution consumes 18.7mW power and around 0.087mm² silicon area.
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 69 (1) , 415-427
An Interference-Tolerant Synchronization Scheme for Wireless Communication Systems Based on Direct Sequence Spread Spectrum
In this paper, an interference-tolerant three-level synchronization scheme for wireless communication systems based on Direct Sequence Spread Spectrum (DSSS) is presented. Although the proposed synchronization scheme is demonstrated in a mixed signal IC solution, it is exportable to fully digital realizations. The proposed technique synchronizes the received pseudo-random sequence (PRS) modulated signal with the receiver (RX) reference PRS by making use of its autocorrelation properties. The proposed scheme employs 3 levels that make the proposed scheme tolerant to strong in-band interferences. Experimental results for the prototype demonstrate the capabilities of the proposed approach to achieve over 50% of clock cycle tracking even in the presence of interferences with a power of 5dB higher than the desired signal power. Fabricated in a mainstream 40nm CMOS technology, the synchronization scheme employs 100MHz PRS at TX and RX; the proposed solution consumes 18.7mW power and around 0.087mm² silicon area.
- 15 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (11) , 3790-3803
An Efficient Sinusoid-Like Pseudo Random Sequence Modulator/Demodulator System With Reduced Adjacent Channel Leakage and High Rejection to Random and Systematic Interference
Emerging wireless communication services require the efficient use of available spectrum and improved co-existence of different standards placed in adjacent frequency bands. Co-existence with leakage from primary users in adjacent channels, which falls in the band of interest, is a primary concern for existing and emerging technologies. In this paper, a mixed signal IC technique based on direct sequence spread spectrum is proposed to improve co-existence of radar systems with commercial wireless communication systems. A sinusoid-like pseudo-random sequence is introduced to reduce leakage from radar systems into adjacent channels. The proposed approach reduces the radar signal leakage on adjacent channels by about 22dB when compared with the conventional binary pseudo-random sequence. The proposed technique randomizes narrow and wideband systematic in-band interference, after which interference power can be effectively attenuated through averaging techniques. Experimental results from a 40nm CMOS technology modulator/demodulator prototype demonstrates the feasibility of the proposed architecture. The modulator and demodulator system requires a silicon area of 0.0459mm² and consumes 4.33mW in total.
- 15 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (11) , 3790-3803
An Efficient Sinusoid-Like Pseudo Random Sequence Modulator/Demodulator System With Reduced Adjacent Channel Leakage and High Rejection to Random and Systematic Interference
Emerging wireless communication services require the efficient use of available spectrum and improved co-existence of different standards placed in adjacent frequency bands. Co-existence with leakage from primary users in adjacent channels, which falls in the band of interest, is a primary concern for existing and emerging technologies. In this paper, a mixed signal IC technique based on direct sequence spread spectrum is proposed to improve co-existence of radar systems with commercial wireless communication systems. A sinusoid-like pseudo-random sequence is introduced to reduce leakage from radar systems into adjacent channels. The proposed approach reduces the radar signal leakage on adjacent channels by about 22dB when compared with the conventional binary pseudo-random sequence. The proposed technique randomizes narrow and wideband systematic in-band interference, after which interference power can be effectively attenuated through averaging techniques. Experimental results from a 40nm CMOS technology modulator/demodulator prototype demonstrates the feasibility of the proposed architecture. The modulator and demodulator system requires a silicon area of 0.0459mm² and consumes 4.33mW in total.
- 13 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (11) , 3618-3629
A 12-Bit 125-MS/s 2.5-Bit/Cycle SAR-Based Pipeline ADC Employing a Self-Biased Gain Boosting Amplifier
This paper introduces a 12 bit 2.5 bit/cycle SAR-based pipeline ADC employing a self-bias gain boosting amplifier. The single-stage amplifier achieves a low-frequency gain of 37 dB, while consuming 1.3 mW of power consumption with 1.3 V of analog power supply. A 2.5 bit/cycle SAR ADC realizes as the sub-ADC in each stage, and reduces both power consumption and silicon area. A two-channel sampling architecture is employed to double the sampling rate and thereby maximize circuit efficiency. A digital calibration technique is used to reduce non-linearity and mismatches due to the RDAC, as well as gain error and offset of the open-loop residue amplifier. The prototype ADC was fabricated in TSMC 40-nm technology, and consumes 10.71 mW with 1.1 V / 1.3 V digital / analog power supplies. When operating at 125 MS/s, the ADC achieves an SFDR of 66.59 dB before calibration and 80.3 dB after calibration when measured at Nyquist frequency. The experimental results show a Walden FoM of 101 fJ/c.-s. before calibration and 47 fJ/c.-s. after calibration.
- 13 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (11) , 3618-3629
A 12-Bit 125-MS/s 2.5-Bit/Cycle SAR-Based Pipeline ADC Employing a Self-Biased Gain Boosting Amplifier
This paper introduces a 12 bit 2.5 bit/cycle SAR-based pipeline ADC employing a self-bias gain boosting amplifier. The single-stage amplifier achieves a low-frequency gain of 37 dB, while consuming 1.3 mW of power consumption with 1.3 V of analog power supply. A 2.5 bit/cycle SAR ADC realizes as the sub-ADC in each stage, and reduces both power consumption and silicon area. A two-channel sampling architecture is employed to double the sampling rate and thereby maximize circuit efficiency. A digital calibration technique is used to reduce non-linearity and mismatches due to the RDAC, as well as gain error and offset of the open-loop residue amplifier. The prototype ADC was fabricated in TSMC 40-nm technology, and consumes 10.71 mW with 1.1 V / 1.3 V digital / analog power supplies. When operating at 125 MS/s, the ADC achieves an SFDR of 66.59 dB before calibration and 80.3 dB after calibration when measured at Nyquist frequency. The experimental results show a Walden FoM of 101 fJ/c.-s. before calibration and 47 fJ/c.-s. after calibration.
- 16 September 2019
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 102 (2) , 331-340
Automatic tuning scheme for second order bandstop filters based on phase comparison
- 16 September 2019
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 102 (2) , 331-340
Automatic tuning scheme for second order bandstop filters based on phase comparison
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (8) , 3134-3147
A 3–6-GHz Highly Linear I-Channel Receiver With Over +3.0-dBm In-Band P 1dB and 200-MHz Baseband Bandwidth Suitable for 5G Wireless and Cognitive Radio Applications
A highly linear I-channel receiver prototype is presented for a 3-6-GHz broadband radio system with a 200-MHz baseband bandwidth and verified to operate under congested spectrum environments. A direct conversion receiver developed from this prototype is suitable for a cognitive radio, a fifth-generation (5G) receiver, and other wireless systems with a total (in-band signal plus blocker) power of above -6.0 dBm. The broadband receiver consists of a low-noise transconductance amplifier (LNTA), a passive mixer, a wideband transimpedance amplifier, and a power-efficient minimally invasive baseband filter. The LNTA with high linearity employs a cross-coupled structure and resistive degeneration to achieve low noise and high linearity simultaneously. The common-gate-based LNTA achieves 2.3-dB noise figure in simulation. Fabricated in a mainstream 40-nm CMOS technology, the worst case measured system noise figure is under 5.8 dB at 3-MHz baseband frequency, and the conversion gain is larger than 12.8 dB with passband variations under 2 dB from 1- up to 200-MHz signal bandwidth. Over 3-6 GHz, the receiver's in-band input third-order intercept point (IIP3) and input P1db are higher than 15.1 and 3.0 dBm, respectively, whereas the power consumption varies from 64.1 to 69.6 mW.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (8) , 3134-3147
A 3–6-GHz Highly Linear I-Channel Receiver With Over +3.0-dBm In-Band P 1dB and 200-MHz Baseband Bandwidth Suitable for 5G Wireless and Cognitive Radio Applications
A highly linear I-channel receiver prototype is presented for a 3-6-GHz broadband radio system with a 200-MHz baseband bandwidth and verified to operate under congested spectrum environments. A direct conversion receiver developed from this prototype is suitable for a cognitive radio, a fifth-generation (5G) receiver, and other wireless systems with a total (in-band signal plus blocker) power of above -6.0 dBm. The broadband receiver consists of a low-noise transconductance amplifier (LNTA), a passive mixer, a wideband transimpedance amplifier, and a power-efficient minimally invasive baseband filter. The LNTA with high linearity employs a cross-coupled structure and resistive degeneration to achieve low noise and high linearity simultaneously. The common-gate-based LNTA achieves 2.3-dB noise figure in simulation. Fabricated in a mainstream 40-nm CMOS technology, the worst case measured system noise figure is under 5.8 dB at 3-MHz baseband frequency, and the conversion gain is larger than 12.8 dB with passband variations under 2 dB from 1- up to 200-MHz signal bandwidth. Over 3-6 GHz, the receiver's in-band input third-order intercept point (IIP3) and input P1db are higher than 15.1 and 3.0 dBm, respectively, whereas the power consumption varies from 64.1 to 69.6 mW.
- Open Access
- 17 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (9) , 3453-3463
Blocker-Tolerant and High-Sensitivity $\Delta \Sigma $ Correlation Digitizer for Radar and Coherent Receiver ApplicationsIn this paper, a coherent subsampling digitizer for pulsed Doppler radar systems is proposed. Prior to transmission, the radar system modulates the RF pulse with a known pseudorandom binary phase shift keying (BPSK) sequence. Upon reception, the radar digitizer uses a programmable sample-and-hold circuit to multiply the received waveform by a properly time-delayed version of the known a priori BPSK sequence. This operation demodulates the desired echo signal while suppressing the spectrum of all in-band noncorrelated interferers, making them appear as noise in the frequency domain. The resulting demodulated narrowband Doppler waveform is then subsampled at the IF frequency by a delta-sigma modulator. Because the digitization bandwidth within the delta-sigma feedback loop is much less than the input bandwidth to the digitizer, the thermal noise outside of the Doppler bandwidth is effectively filtered prior to quantization, providing an increase in signal-to-noise ratio (SNR) at the digitizer's output compared with the input SNR. In this demonstration, a delta-sigma correlation digitizer is fabricated in a 0.18-μm CMOS technology. The digitizer has a power consumption of 1.12 mW with an IIP3 of 7.5 dBm. The digitizer is able to recover Doppler tones in the presence of blockers up to 40 dBm greater than the Doppler tone.
- 17 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (9) , 3453-3463
Open AccessBlocker-Tolerant and High-Sensitivity $\Delta \Sigma $ Correlation Digitizer for Radar and Coherent Receiver ApplicationsIn this paper, a coherent subsampling digitizer for pulsed Doppler radar systems is proposed. Prior to transmission, the radar system modulates the RF pulse with a known pseudorandom binary phase shift keying (BPSK) sequence. Upon reception, the radar digitizer uses a programmable sample-and-hold circuit to multiply the received waveform by a properly time-delayed version of the known a priori BPSK sequence. This operation demodulates the desired echo signal while suppressing the spectrum of all in-band noncorrelated interferers, making them appear as noise in the frequency domain. The resulting demodulated narrowband Doppler waveform is then subsampled at the IF frequency by a delta-sigma modulator. Because the digitization bandwidth within the delta-sigma feedback loop is much less than the input bandwidth to the digitizer, the thermal noise outside of the Doppler bandwidth is effectively filtered prior to quantization, providing an increase in signal-to-noise ratio (SNR) at the digitizer's output compared with the input SNR. In this demonstration, a delta-sigma correlation digitizer is fabricated in a 0.18-μm CMOS technology. The digitizer has a power consumption of 1.12 mW with an IIP3 of 7.5 dBm. The digitizer is able to recover Doppler tones in the presence of blockers up to 40 dBm greater than the Doppler tone.
- 21 June 2016
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 88 (2) , 181-183
Special Issue on the 57th International Midwest Symposium on Circuits and Systems
- 21 June 2016
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 88 (2) , 181-183
Special Issue on the 57th International Midwest Symposium on Circuits and Systems