Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mykola Chausov has a total of 39 co-authors. Here are the top co-authors by number of shared publications:

  • Andrii Pylypenko

    Department of Mechanics, National University of Life and Environmental Sciences of Ukraine, Heroiv Oborony str. 15, 03041 Kyiv, Ukraine

    8 shared publications
  • Pavlo Maruschak

    Department of Automation of Technological Processes and Production, Ternopil Ivan Puluj National Technical University, 46001 Ternopil, Ukraine

    7 shared publications
  • Volodymyr Hutsaylyuk

    Faculty of Mechanical Engineering, Military University of Technology, Gen. S. Kaliskiego Str. 2, 00-908 Warsaw, Poland

    4 shared publications
  • Jakub Brezina

    Department of Technology, Materials and Computer Aided Production, Faculty of Mechanical Engineering, Technical University of Košice, 042 00 Košice, Slovakia

    2 shared publications
  • Janette Brezinová

    Department of Automotive Production, Faculty of Mechanical Engineering, Technical University of Košice, 042 00 Košice, Slovakia

    2 shared publications
  • Myroslav V. Karpets

    Department of Physical Materials Science and Heat Treatment, Y.O. Paton Institute of Materials Science and Welding, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, 37 Beresteiskyi Ave., 03056 Kyiv, Ukraine

    2 shared publications

Latest Publications

  • Open Access

    Risks Associated with the Use of Stainless Steel X10CrNi18-8 Under Combined Impact-Oscillatory Loading and Cryogenic Cooling

    by Mykola Chausov, Pavlo Maruschak, Andrii Pylypenko, Vladyslav Shmanenko, Maksym Lisnichuk, Daria Yudina, Pavol Sovák, Jakub Brezina, Volodymyr Hutsaylyuk

    The study establishes key patterns in the influence of pre-applied impact-oscillatory loading (IOL) of varying intensity—realizing dynamic non-equilibrium processes (DNP)—in liquid nitrogen on the mechanical properties and structural state of stainless steel X10CrNi18-8. Static tensile deformation was investigated at room temperature following impulsive strain levels of εimp = 0.06–2.69%. A wave-like mechanical response of the steel to DNP was observed within this εimp range, most pronounced at εimp = 0.11% and εimp = 2.69%. After DNP at εimp = 0.11%, despite a maximum increase in ultimate strength by 5.25%, the relative elongation of the specimen increased to 10.3%. The scatter in ultimate tensile strength specimens across all loading regimes was within 6.38%, while the variation in ductility reached up to 21.25%. In contrast, after εimp = 2.69%, the stress–strain diagram resembled that of the steel in its initial state. Metallophysical investigations and X-ray diffraction analysis were conducted to explain the observed effects. At εimp > 2.7%, the high-strength but low-ductility X10CrNi18-8 steel undergoes brittle failure under impulsive loading. At the same time, the total fraction of the more brittle martensitic phase in the steel microstructure reaches approximately 22%.

  • Open Access

    Structural and Functional Co‐Adaptation of Plants of the Genus Lysimachia L. (Primulaceae) and Pollinating Insects of the Genus Macropis Panzer (Hymenoptera, Melittidae)

    by Vladimir G. Radchenko, Mykola G. Chausov, Artur F. Likhanov, Hanna Yu. Honchar, Denis Michez

    The pollination system ‘oil‐collecting bees Macropis and oil‐producing plants Lysimachia ’, probably originated a long time ago. Although much is already known about the biology and ecology of this fascinating interaction, we reveal here features of the structural elements of the secretory system of the Lysimachia flowers and the foraging behaviour of Macropis bees. A model describing the process of collecting flower oil by bees based on the laws of mechanics is presented. The model considers the histochemical and morphological features of the secretory apparatus in Lysimachia flowers, as well as the behaviour and micromorphological structure of the oil‐ and pollen‐collecting apparatus of the bee. All these structures seem to be adapted for collecting flower oil and other metabolic products, demonstrating a process of co‐adaptation. It has been clarified for the first time that Macropis females do not merely collect pure floral oil through capillary absorption or by mopping up oil from trichomes on the flower stamens and petals via specialised pubescence on the fore‐ and mid‐tibia and tarsi of bees, as was previously thought. Instead, they collect entire oil‐filled trichome heads by breaking them off from the trichome stems. A neck (intermediate) cell has been described in the oil‐secreting capitate trichomes of Lysimachia nummularia L. The dominance of pectin and hemicellulose in its cell walls, combined with high beta‐galactosidase activity during trichome maturation, creates conditions for the formation of a microabscission zone. This zone facilitates the detachment of the oil‐containing capitate when contact occurs with pollinating bees of the genus Macropis .


  • Bending Tests of a Single-lap Adhesive Joint

    by Paweł Bogusz, Agnieszka Derewońko, Mykola Chausov, Andrii Pylypenko

    The strength and durability of the adhesive joint are, among other factors, a function of the joint’s dimensions and the size ofthe adhesive layer acting as a connecting element. In practice, the thickness of the adhesive layer is the result of, i.a., the tolerance of thejoined elements. The main purpose of the article is to determine the initial deformation of a single-lap adhesive joint at the stage of fixingthe joint in the grips of the testing machine. The article considers various aspects of manufacturing specimens of a single-lap adhesivejoint, as well as the repeatability of the dimensions of the joined aluminum tabs. The effect of tab preparation technology on the overalldimensions of the joint is discussed. A statistical analysis of the dimensions of the aluminum tabs, as well as the length and the thicknessof the adhesive layer is presented. A device and technology for producing a single-lap adhesive joint with repeatable dimensions underlaboratory conditions, along with an example of this device’s application, are also presented. The final part of the paper presents tests ofthe initial deformation of a single-lap adhesive joint during alignment of the overlap axis. A specially designed fixture enabling such testsis described in detail. In the tests undertaken to determine the initial deformation of the joint and the change in the clamping force of themovable handle on the upper tab, it was shown that there is no permanent deformation at the stage of aligning the tabs.

  • Open Access

    Cryogenic Investigations into the Effect of Impact-Oscillatory Loading on Changes in the Mechanical Properties and Structural Condition of VT23M Two-Phase Titanium Alloy

    by Mykola Chausov, Volodymyr Hutsaylyuk, Pavlo Maruschak, Andrii Pylypenko, Myroslav Karpets, Vladyslav Shmanenko

    Impact-oscillatory loading of variable intensity was applied to the VT23M high-strength sheet two-phase titanium alloy in liquid nitrogen. This was carried out to investigate the effect of this loading type on changes in the mechanical properties and structural condition of the alloy upon subsequent static tensioning at normal temperature. Dynamic non-equilibrium process (DNP) realized at a temperature of liquid nitrogen proved to be unable to impair the strength properties of the VT23M titanium alloy compared to room temperature; however, they caused a significant decrease in ductility (down to 16%). The impaired plastic properties of the alloy were shown to entail additional defects in the structural components of the alloy. The authors have found patterns of damage accumulation in the structural components of the alloy depending on the DNP parameters. They are in good agreement with the findings of the fractographic research.


  • Open Access

    Effective method of evaluating the level of material damage under different loading conditions

    by V. Kosarchuk, M. Chausov, V. Tverdomed

    У статті проаналізовано відомі експериментальні результати оцінки ступеню пошкодження конструкційних матеріалів різних марок за умов довготривалого, циклічного, статичного навантаження та мастильного тертя. Показано, що структурні зміни, які відбуваються в матеріалах під час навантаження, корелюють зі змінами статистичних характеристик розсіювання результатів вимірювання твердості. Це дозволяє прогнозувати кінетику накопичення пошкоджень у матеріалах під час експлуатації, а отже, прогнозувати термін їх служби. Такий підхід є актуальним для розробки методів оцінки поточного стану та залишкового ресурсу конструкцій залізничного та інших транспортних галузей. Запропоновано використовувати цю методику для оцінки рівня пошкодження мікроструктури матеріалів у зоні контакту та його впливу на трибологічні характеристики металевих пар тертя. Запропоновано новий метод оцінки ефективності мастильних композицій на основі промислових мастил, які містять нанодобавки різного хімічного складу для підвищення зносостійкості сталевих важконавантажених пар тертя. Метод базується на спільному аналізі експериментальних даних щодо кінетики зношування, зміни відносної твердості та рівня пошкодженості поверхневих шарів металів пар тертя. Порушення структури матеріалів у зоні контакту визначають за допомогою статистичних параметрів розсіювання значень твердості. Методика апробована для сталевих пар тертя, де використовуються мастильні матеріали на основі індустріального масла та нанодобавок міді, магнієвих сплавів, графіту та двох марок середньовуглецевих сталей.

  • The influence of impact-oscillation load on hardness of surface layers of D16ChATW aluminium alloy

    by M. G. Chausov, P. O. Maruschak, A. P. Pylypenko

    The effect of impact-oscillation load of a given intensity was evaluated, in particular, using nanosolutions of tungsten carbide, carbon, as well as Al + Cu and Al + Cu + Mg nanosolu­tions at a concentration of 50:50% and 33:33:33%, respectively, on the hardness of the surface layers of the D16ChATW aluminum alloy. The relationship between the parameters of dynamic non-equilibrium processes (DNP), which change the structural phase state and mechanical properties of the alloy and the surface hardness of the material, was identified and described.

  • Open Access

    Impact of the Initial Phase Composition of Alloys on the Effects Manifested by Yield Sites That Occur on Sheet Aluminum Alloys Subjected to Impact-Oscillatory Loading

    by Mykola Chausov, Andrii Pylypenko, Pavlo Maruschak, Vira Zasimchuk, Janette Brezinová, Jakub Brezina, Ján Viňáš

    The impact of the initial phase composition of alloys was evaluated, in particular, the content of Cu, Mn, and Mg in aluminum alloys D16ChATW, 2024-T351 and aluminum alloy T, which in its physical and mechanical characteristics is close to alloy 6013. The impact was evaluated on the effects manifested by yield sites that occur on aluminum alloys that were subject to the dynamic non-equilibrium processes (DNPs) at the expense of impact-oscillatory loading of different intensities under conditions of static tensioning, The one-time DNP, to which the investigated aluminum alloys were subjected at the pre-set levels of elastic strain followed by static tensioning, was found to cause yield sites formation. This is due to self-organization of the alloy structure, which contributes to alloy plasticization. The initial phase alloys composition impact on the yield sites, which occurs when impulse energy of a different intensity is applied to the alloys, was analyzed. The specimens from the aluminum alloys undergoing DNPs of the same level were compared. This made it possible to conclude that alloys D16ChATW and 2024-T351, which have a higher content of Cu, Mn, and Mg, have longer yield sites upon subsequent static tensioning. On the basis of the experimental results, in particular, physical studies, the authors derived a physical and mathematical model of the yield sites that appear after DNPs.


  • Open Access

    LUBRICANT COMPOSITION FOR INCREASING WEAR RESISTANCE OF HEAVY-LOADED FRICTION PAIRS

    by V. Kosarchuk, M. Chausov, V. Tverdomed, A. Pilipenko, O. Aharkov

    The proposed new lubricating composition, which significantly reduces the wear resistance of the rails and wheels of rolling stock during operation, prevents electrochemical corrosion of friction pairs “wheel – rail” and, most importantly, stabilizes the coefficient of friction at the optimum level after a relatively short operating time. The experiments performed on the friction pair “sample of the bandage material of the railway wheel – a sample of the rail material” at the ratio of hardness at the bandage material (Rockwell hardness, HRC scale - 35.3) to the hardness of the rail material 1,1. Test results show that in the case of industrial lubricant, the BioRail brand, with the addition of nanomaterial friction pair with lower wear hardness of the rail metal sample after three hours in operation was practically not observed. Moreover, the average value of the friction coefficient for three hours of operation had been maintained at the level 0.25, which is optimal for the friction pair “wheel – rail”.


  • Shell, a naturally engineered egg packaging: Estimated for strength by non-destructive testing for elastic deformation

    by Valeriy G. Narushin, Mykola G. Chausov, Larysa V. Shevchenko, Andriy P. Pylypenko, Viktor A. Davydovych, Michael N. Romanov, Darren K. Griffin


  • Influence of Impact-Oscillatory Loading on Fatigue Life of Aluminium Alloy 2024-T351

    by Mykola Chausov, Elena Zasimchuk, Pavlo Maruschak, Oleg Khyzhun, Andrii Pylypenko, Olegas Prentkovskis, Janette Brezinová