Andrii Pylypenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Andrii Pylypenko has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
- Pavlo Maruschak
Department of Automation of Technological Processes and Production, Ternopil Ivan Puluj National Technical University, 46001 Ternopil, Ukraine
25 shared publications - Mykola Chausov
Department of Mechanics, National University of Life and Environmental Sciences of Ukraine, Heroiv Oborony str. 15, 03041 Kyiv, Ukraine
12 shared publications - Volodymyr Hutsaylyuk
Faculty of Mechanical Engineering, Military University of Technology, Gen. S. Kaliskiego Str. 2, 00-908 Warsaw, Poland
11 shared publications - Mykola Chausov
Department of Mechanics, National University of Life and Environmental Sciences of Ukraine, Heroiv Oborony str. 15, 03041 Kyiv, Ukraine
8 shared publications - Janette Brezinová
Department of Automotive Production, Faculty of Mechanical Engineering, Technical University of Košice, 042 00 Košice, Slovakia
7 shared publications Mykola Chausov
7 shared publications
Latest Publications
- Open Access
- 23 October 2024
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 146 (6) , 1-4
Predicting the Effects of Cryogenic Treatment and Impact-Oscillatory Loading on Changes in the Strength Properties of Stainless Steels
New experimental results concerning the strength properties of stainless steels are analyzed. In particular, the strength properties of steels were improved at room temperature using the preliminary impact-oscillatory loading (IOL) in liquid nitrogen. Mechanical tests performed on stainless steel 12Kh18N10T have found the IOL conditions (deformation of the material during pulse loading—εimp = 9.69%), under which the ultimate strength of steel increases by 32.2% compared to the initial state under subsequent static tensioning. Metallographic analysis of the deformed steel revealed twinning in the microstructure. This accounts for a significant increase in ultimate strength under subsequent static tensioning. A method for estimating the ultimate strength of stainless steels of different chemical compositions by changing the percentage of the main chemical elements is proposed. To test this technique, stainless steel 12Kh18N9 was chosen. Similar studies using this steel at εimp = 9.5% in liquid nitrogen followed by static tensioning at room temperature have confirmed the effectiveness of the proposed approach.
- 23 October 2024
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 146 (6) , 1-4
Open AccessPredicting the Effects of Cryogenic Treatment and Impact-Oscillatory Loading on Changes in the Strength Properties of Stainless Steels
New experimental results concerning the strength properties of stainless steels are analyzed. In particular, the strength properties of steels were improved at room temperature using the preliminary impact-oscillatory loading (IOL) in liquid nitrogen. Mechanical tests performed on stainless steel 12Kh18N10T have found the IOL conditions (deformation of the material during pulse loading—εimp = 9.69%), under which the ultimate strength of steel increases by 32.2% compared to the initial state under subsequent static tensioning. Metallographic analysis of the deformed steel revealed twinning in the microstructure. This accounts for a significant increase in ultimate strength under subsequent static tensioning. A method for estimating the ultimate strength of stainless steels of different chemical compositions by changing the percentage of the main chemical elements is proposed. To test this technique, stainless steel 12Kh18N9 was chosen. Similar studies using this steel at εimp = 9.5% in liquid nitrogen followed by static tensioning at room temperature have confirmed the effectiveness of the proposed approach.
- 30 September 2024
- Published by Index Copernicus in Bulletin of the Military University of Technology
- Vol. 73 (3) , 9-20
Bending Tests of a Single-lap Adhesive Joint
The strength and durability of the adhesive joint are, among other factors, a function of the joint’s dimensions and the size ofthe adhesive layer acting as a connecting element. In practice, the thickness of the adhesive layer is the result of, i.a., the tolerance of thejoined elements. The main purpose of the article is to determine the initial deformation of a single-lap adhesive joint at the stage of fixingthe joint in the grips of the testing machine. The article considers various aspects of manufacturing specimens of a single-lap adhesivejoint, as well as the repeatability of the dimensions of the joined aluminum tabs. The effect of tab preparation technology on the overalldimensions of the joint is discussed. A statistical analysis of the dimensions of the aluminum tabs, as well as the length and the thicknessof the adhesive layer is presented. A device and technology for producing a single-lap adhesive joint with repeatable dimensions underlaboratory conditions, along with an example of this device’s application, are also presented. The final part of the paper presents tests ofthe initial deformation of a single-lap adhesive joint during alignment of the overlap axis. A specially designed fixture enabling such testsis described in detail. In the tests undertaken to determine the initial deformation of the joint and the change in the clamping force of themovable handle on the upper tab, it was shown that there is no permanent deformation at the stage of aligning the tabs.
- 30 September 2024
- Published by Index Copernicus in Bulletin of the Military University of Technology
- Vol. 73 (3) , 9-20
Bending Tests of a Single-lap Adhesive Joint
The strength and durability of the adhesive joint are, among other factors, a function of the joint’s dimensions and the size ofthe adhesive layer acting as a connecting element. In practice, the thickness of the adhesive layer is the result of, i.a., the tolerance of thejoined elements. The main purpose of the article is to determine the initial deformation of a single-lap adhesive joint at the stage of fixingthe joint in the grips of the testing machine. The article considers various aspects of manufacturing specimens of a single-lap adhesivejoint, as well as the repeatability of the dimensions of the joined aluminum tabs. The effect of tab preparation technology on the overalldimensions of the joint is discussed. A statistical analysis of the dimensions of the aluminum tabs, as well as the length and the thicknessof the adhesive layer is presented. A device and technology for producing a single-lap adhesive joint with repeatable dimensions underlaboratory conditions, along with an example of this device’s application, are also presented. The final part of the paper presents tests ofthe initial deformation of a single-lap adhesive joint during alignment of the overlap axis. A specially designed fixture enabling such testsis described in detail. In the tests undertaken to determine the initial deformation of the joint and the change in the clamping force of themovable handle on the upper tab, it was shown that there is no permanent deformation at the stage of aligning the tabs.
- Open Access
Cryogenic Investigations into the Effect of Impact-Oscillatory Loading on Changes in the Mechanical Properties and Structural Condition of VT23M Two-Phase Titanium Alloy
Impact-oscillatory loading of variable intensity was applied to the VT23M high-strength sheet two-phase titanium alloy in liquid nitrogen. This was carried out to investigate the effect of this loading type on changes in the mechanical properties and structural condition of the alloy upon subsequent static tensioning at normal temperature. Dynamic non-equilibrium process (DNP) realized at a temperature of liquid nitrogen proved to be unable to impair the strength properties of the VT23M titanium alloy compared to room temperature; however, they caused a significant decrease in ductility (down to 16%). The impaired plastic properties of the alloy were shown to entail additional defects in the structural components of the alloy. The authors have found patterns of damage accumulation in the structural components of the alloy depending on the DNP parameters. They are in good agreement with the findings of the fractographic research.
Open AccessCryogenic Investigations into the Effect of Impact-Oscillatory Loading on Changes in the Mechanical Properties and Structural Condition of VT23M Two-Phase Titanium Alloy
Impact-oscillatory loading of variable intensity was applied to the VT23M high-strength sheet two-phase titanium alloy in liquid nitrogen. This was carried out to investigate the effect of this loading type on changes in the mechanical properties and structural condition of the alloy upon subsequent static tensioning at normal temperature. Dynamic non-equilibrium process (DNP) realized at a temperature of liquid nitrogen proved to be unable to impair the strength properties of the VT23M titanium alloy compared to room temperature; however, they caused a significant decrease in ductility (down to 16%). The impaired plastic properties of the alloy were shown to entail additional defects in the structural components of the alloy. The authors have found patterns of damage accumulation in the structural components of the alloy depending on the DNP parameters. They are in good agreement with the findings of the fractographic research.
- Open Access
Impact of the Initial Phase Composition of Alloys on the Effects Manifested by Yield Sites That Occur on Sheet Aluminum Alloys Subjected to Impact-Oscillatory Loading
The impact of the initial phase composition of alloys was evaluated, in particular, the content of Cu, Mn, and Mg in aluminum alloys D16ChATW, 2024-T351 and aluminum alloy T, which in its physical and mechanical characteristics is close to alloy 6013. The impact was evaluated on the effects manifested by yield sites that occur on aluminum alloys that were subject to the dynamic non-equilibrium processes (DNPs) at the expense of impact-oscillatory loading of different intensities under conditions of static tensioning, The one-time DNP, to which the investigated aluminum alloys were subjected at the pre-set levels of elastic strain followed by static tensioning, was found to cause yield sites formation. This is due to self-organization of the alloy structure, which contributes to alloy plasticization. The initial phase alloys composition impact on the yield sites, which occurs when impulse energy of a different intensity is applied to the alloys, was analyzed. The specimens from the aluminum alloys undergoing DNPs of the same level were compared. This made it possible to conclude that alloys D16ChATW and 2024-T351, which have a higher content of Cu, Mn, and Mg, have longer yield sites upon subsequent static tensioning. On the basis of the experimental results, in particular, physical studies, the authors derived a physical and mathematical model of the yield sites that appear after DNPs.
Open AccessImpact of the Initial Phase Composition of Alloys on the Effects Manifested by Yield Sites That Occur on Sheet Aluminum Alloys Subjected to Impact-Oscillatory Loading
The impact of the initial phase composition of alloys was evaluated, in particular, the content of Cu, Mn, and Mg in aluminum alloys D16ChATW, 2024-T351 and aluminum alloy T, which in its physical and mechanical characteristics is close to alloy 6013. The impact was evaluated on the effects manifested by yield sites that occur on aluminum alloys that were subject to the dynamic non-equilibrium processes (DNPs) at the expense of impact-oscillatory loading of different intensities under conditions of static tensioning, The one-time DNP, to which the investigated aluminum alloys were subjected at the pre-set levels of elastic strain followed by static tensioning, was found to cause yield sites formation. This is due to self-organization of the alloy structure, which contributes to alloy plasticization. The initial phase alloys composition impact on the yield sites, which occurs when impulse energy of a different intensity is applied to the alloys, was analyzed. The specimens from the aluminum alloys undergoing DNPs of the same level were compared. This made it possible to conclude that alloys D16ChATW and 2024-T351, which have a higher content of Cu, Mn, and Mg, have longer yield sites upon subsequent static tensioning. On the basis of the experimental results, in particular, physical studies, the authors derived a physical and mathematical model of the yield sites that appear after DNPs.
- Open Access
- 29 September 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (10) , 244
Nanopowders of Different Chemical Composition Added to Industrial Lubricants and Their Impact on Wear Resistance of Steel Friction Pairs
The authors have previously proposed and tested a method for increasing the wear resistance of heavy-loaded friction pairs by saturating industrial lubricants with the metallic nanopowder of the friction pair’s component that has a lower hardness. To confirm the effectiveness of this concept, this paper presents the results of experimental investigations into the tribological characteristics of two medium carbon steels (rail steel K74 and structural steel 20) during sliding friction. Friction surfaces lubricated with compositions based on the Bio Rail industrial lubricant were saturated with nanopowder additives of copper, carbon, and magnesium alloy, as well as K74 and 20 steels. The research findings indicate that lubricants saturated with nanomaterials of K74 and 20 steels help achieve the highest wear resistance, as compared to lubricants based on pure grease and lubricating compositions based on copper, magnesium alloy and carbon powders. The test results confirmed that the mean friction coefficient of the rail steel remained at the level of 0.25 for three hours of operation, which is optimal for the “wheel–rail” friction pair. The proposed method of manufacturing lubricating compositions can be used to improve the efficiency of lubrication of railway rails and rolling stock wheels.
- 29 September 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (10) , 244
Open AccessNanopowders of Different Chemical Composition Added to Industrial Lubricants and Their Impact on Wear Resistance of Steel Friction Pairs
The authors have previously proposed and tested a method for increasing the wear resistance of heavy-loaded friction pairs by saturating industrial lubricants with the metallic nanopowder of the friction pair’s component that has a lower hardness. To confirm the effectiveness of this concept, this paper presents the results of experimental investigations into the tribological characteristics of two medium carbon steels (rail steel K74 and structural steel 20) during sliding friction. Friction surfaces lubricated with compositions based on the Bio Rail industrial lubricant were saturated with nanopowder additives of copper, carbon, and magnesium alloy, as well as K74 and 20 steels. The research findings indicate that lubricants saturated with nanomaterials of K74 and 20 steels help achieve the highest wear resistance, as compared to lubricants based on pure grease and lubricating compositions based on copper, magnesium alloy and carbon powders. The test results confirmed that the mean friction coefficient of the rail steel remained at the level of 0.25 for three hours of operation, which is optimal for the “wheel–rail” friction pair. The proposed method of manufacturing lubricating compositions can be used to improve the efficiency of lubrication of railway rails and rolling stock wheels.
- Open Access
Plastic Anisotropy Effect on Variation of Mechanical and Structural Properties of VT23 Titanium Alloy Subjected to Impact-Oscillatory Loading
The main regularities in the impact of varying intensity impact-oscillatory loading on the variation of the mechanical and structural properties of the VT23 high-strength two-phase transverse-rolled sheet titanium alloy have been found. The intensity of the impulse introduction of energy into the alloy under the dynamic non-equilibrium process (DNP) was estimated by εimp (the increment of dynamic strain). The pulse intensity was found to change the shape of the static strain diagram with further tensioning, as compared to the initial state. This indicates the effect from the structure self-organization inherent in the VT23 titanium alloy upon the DNP. After the DNP (εimp = 1.44%), with further static deformation, the tensile diagram revealed yield sites up to 6.5% long. In most cases, the DNP was found to have a negative effect on the variation of the mechanical properties of the VT23 titanium alloy, especially if the latter was rolled in the transverse direction. The optimal DNP intensity is εimp~1.5%. In this case, the DNP can be used as an effective plasticization technology for the VT23 titanium alloy (regardless of the rolling direction) in the stamping of high-strength titanium alloys. Changes in the mechanical and structural condition of the VT23 titanium alloy subjected to the DNP were confirmed by the fractographic investigation of specimen fractures.
Open AccessPlastic Anisotropy Effect on Variation of Mechanical and Structural Properties of VT23 Titanium Alloy Subjected to Impact-Oscillatory Loading
The main regularities in the impact of varying intensity impact-oscillatory loading on the variation of the mechanical and structural properties of the VT23 high-strength two-phase transverse-rolled sheet titanium alloy have been found. The intensity of the impulse introduction of energy into the alloy under the dynamic non-equilibrium process (DNP) was estimated by εimp (the increment of dynamic strain). The pulse intensity was found to change the shape of the static strain diagram with further tensioning, as compared to the initial state. This indicates the effect from the structure self-organization inherent in the VT23 titanium alloy upon the DNP. After the DNP (εimp = 1.44%), with further static deformation, the tensile diagram revealed yield sites up to 6.5% long. In most cases, the DNP was found to have a negative effect on the variation of the mechanical properties of the VT23 titanium alloy, especially if the latter was rolled in the transverse direction. The optimal DNP intensity is εimp~1.5%. In this case, the DNP can be used as an effective plasticization technology for the VT23 titanium alloy (regardless of the rolling direction) in the stamping of high-strength titanium alloys. Changes in the mechanical and structural condition of the VT23 titanium alloy subjected to the DNP were confirmed by the fractographic investigation of specimen fractures.
- Open Access
- 11 April 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (4) , 64
Increasing Wear Resistance of Heavy-Loaded Friction Pairs by Nanoparticles in Conventional Lubricants: A Proof of Concept
This paper provides experimental data on the effective use of a new lubricating composition, which includes industrial oil of any brand with the addition of a nanometal of the component of a friction pair, which has a lower hardness. It is shown that this composition significantly reduces the wear resistance of the rails and wheels of rolling stock during operation, prevents electrochemical corrosion of the friction pair wheel–rail and, most importantly, stabilizes the coefficient of friction at the optimum level after a relatively short operating time. The experiments were performed on the friction pair, “sample of the bandage material of the railway wheel—a sample of the rail material”, with a ratio of hardness of the bandage material (Rockwell hardness, HRC scale—35.3) to the hardness of the rail material of 1.1. Test results show that in the case of industrial lubricant, the BioRail brand, with the addition of a nanomaterial friction pair with lower wear hardness of the rail metal sample, after three hours in operation the wear was practically not observed. Moreover, the average value of the friction coefficient for three hours of operation was maintained at the level 0.25, which is optimal for the friction pair wheel–rail. Similar experiments using only the same lubricant brand showed much worse results.
- 11 April 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (4) , 64
Open AccessIncreasing Wear Resistance of Heavy-Loaded Friction Pairs by Nanoparticles in Conventional Lubricants: A Proof of Concept
This paper provides experimental data on the effective use of a new lubricating composition, which includes industrial oil of any brand with the addition of a nanometal of the component of a friction pair, which has a lower hardness. It is shown that this composition significantly reduces the wear resistance of the rails and wheels of rolling stock during operation, prevents electrochemical corrosion of the friction pair wheel–rail and, most importantly, stabilizes the coefficient of friction at the optimum level after a relatively short operating time. The experiments were performed on the friction pair, “sample of the bandage material of the railway wheel—a sample of the rail material”, with a ratio of hardness of the bandage material (Rockwell hardness, HRC scale—35.3) to the hardness of the rail material of 1.1. Test results show that in the case of industrial lubricant, the BioRail brand, with the addition of a nanomaterial friction pair with lower wear hardness of the rail metal sample, after three hours in operation the wear was practically not observed. Moreover, the average value of the friction coefficient for three hours of operation was maintained at the level 0.25, which is optimal for the friction pair wheel–rail. Similar experiments using only the same lubricant brand showed much worse results.
- Open Access
Phenomenological Models and Peculiarities of Evaluating Fatigue Life of Aluminum Alloys Subjected to Dynamic Non-Equilibrium Processes
Physical-mechanical models for predicting the fatigue life of aluminum alloys D16ChATW and 2024-T351 are proposed and tested. Damage accumulation patterns are established for these alloys in the initial state and after dynamic non-equilibrium processes (DNP) of different intensity that occur at maximum cycle stresses σmax from 340 to 440 MPa, cycle asymmetry coefficients R = 0.1 and load frequency f = 110 Hz. The main model parameters are the initial alloy hardness HV and the limiting parameters of scatter of hardness values m. These parameters are evaluated in the process of cyclic loading with fixed maximum stresses of the cycles. Relative values me are also considered. For the alloys in the initial state, the proposed models are shown to be in good agreement with the experimental results. Conversely, structural changes taking place in alloys after DNP complicate the prediction of their fatigue life.
Open AccessPhenomenological Models and Peculiarities of Evaluating Fatigue Life of Aluminum Alloys Subjected to Dynamic Non-Equilibrium Processes
Physical-mechanical models for predicting the fatigue life of aluminum alloys D16ChATW and 2024-T351 are proposed and tested. Damage accumulation patterns are established for these alloys in the initial state and after dynamic non-equilibrium processes (DNP) of different intensity that occur at maximum cycle stresses σmax from 340 to 440 MPa, cycle asymmetry coefficients R = 0.1 and load frequency f = 110 Hz. The main model parameters are the initial alloy hardness HV and the limiting parameters of scatter of hardness values m. These parameters are evaluated in the process of cyclic loading with fixed maximum stresses of the cycles. Relative values me are also considered. For the alloys in the initial state, the proposed models are shown to be in good agreement with the experimental results. Conversely, structural changes taking place in alloys after DNP complicate the prediction of their fatigue life.
- 1 October 2021
- Published by Elsevier in Biosystems Engineering
- Vol. 210, 235-246
Shell, a naturally engineered egg packaging: Estimated for strength by non-destructive testing for elastic deformation
- 1 October 2021
- Published by Elsevier in Biosystems Engineering
- Vol. 210, 235-246
Shell, a naturally engineered egg packaging: Estimated for strength by non-destructive testing for elastic deformation