Lei Gu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lei Gu has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Juan Rivas-Davila
Department of Electrical Engineering, Stanford University, Stanford, CA, USA
14 shared publications - Grayson Zulauf
Power Electronic Systems Laboratory, ETH Zurich, Zurich, Switzerland
3 shared publications - Sombuddha Chakraborty
Kilby Labs, Texas Instruments Inc., Santa Clara, CA, USA
3 shared publications - Zikang Tong
Department of Electrical Engineering, Stanford University, Stanford, CA, USA
3 shared publications Jeronimo Segovia-Fernandez
Texas Instruments Inc., Dallas, TX, USA
2 shared publications- Jiale Xu
Department of Electrical Engineering, Stanford University, Stanford, CA, USA
2 shared publications
Latest Publications
- Open Access
- 8 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4336-4347
Design Considerations for Multimegahertz Resonant Inductive Power Transfer
MHz-frequency inductive wireless power transfer holds the promise of compact and cost-effective wireless power transfer. However, due to the sensitivity of the high-frequency circuit operations to the parasitic components, these systems are universally less efficient, on a dc-dc basis, than wireless power systems operating at conventional lower frequency regimes. This paper presents the design considerations for inductive power transfer systems operating at multi-MHz frequencies. Specifically, this work comprehensively analyzes the trade-offs of selecting different compensation topologies, including series-series, series-parallel, parallel-series, and parallel-parallel compensations. The paper also provides guidelines for incorporating parasitic components of semiconductor devices into a multi-MHz circuit design to improve transmission efficiency. Validating the design methodologies, we built three 300 W inductive power transfer systems using series-series, series-parallel, and parallel-parallel compensations, all achieving an ac-ac efficiency above 96%, and compared their performances in detail. Finally, we demonstrate a 6.78 MHz prototype inductive power transfer system that delivers 1.7 kW power with a dc-dc efficiency of 95.7%.
- 8 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (4) , 4336-4347
Open AccessDesign Considerations for Multimegahertz Resonant Inductive Power Transfer
MHz-frequency inductive wireless power transfer holds the promise of compact and cost-effective wireless power transfer. However, due to the sensitivity of the high-frequency circuit operations to the parasitic components, these systems are universally less efficient, on a dc-dc basis, than wireless power systems operating at conventional lower frequency regimes. This paper presents the design considerations for inductive power transfer systems operating at multi-MHz frequencies. Specifically, this work comprehensively analyzes the trade-offs of selecting different compensation topologies, including series-series, series-parallel, parallel-series, and parallel-parallel compensations. The paper also provides guidelines for incorporating parasitic components of semiconductor devices into a multi-MHz circuit design to improve transmission efficiency. Validating the design methodologies, we built three 300 W inductive power transfer systems using series-series, series-parallel, and parallel-parallel compensations, all achieving an ac-ac efficiency above 96%, and compared their performances in detail. Finally, we demonstrate a 6.78 MHz prototype inductive power transfer system that delivers 1.7 kW power with a dc-dc efficiency of 95.7%.
- 17 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 4498-4503
A Prescribed-Instant Convergence Approach to Consensus of High-Order Multiagent Systems
Prescribed-time consensus of multiagent systems is known for its small conservativeness in settling time. Some studies even show that the consensus happens at a prescribed instant. However, the corresponding theoretical proof is not sufficient. In this work, a consensus control based on the backstepping method is designed for multiagent systems with high-order integrator dynamics. Two Lyapunov inequalities force the consensus to happen just at the prescribed instant (prescribed-instant consensus). One of the inequalities ensures the consensus happening not after the preassigned time instant (prescribed-time consensus). The other guarantees the consensus happens not before the prescribed time instant. In the numerical example, a five-node multiagent system simulation validates the proposed prescribed-instant consensus.
- 17 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 4498-4503
A Prescribed-Instant Convergence Approach to Consensus of High-Order Multiagent Systems
Prescribed-time consensus of multiagent systems is known for its small conservativeness in settling time. Some studies even show that the consensus happens at a prescribed instant. However, the corresponding theoretical proof is not sufficient. In this work, a consensus control based on the backstepping method is designed for multiagent systems with high-order integrator dynamics. Two Lyapunov inequalities force the consensus to happen just at the prescribed instant (prescribed-instant consensus). One of the inequalities ensures the consensus happening not after the preassigned time instant (prescribed-time consensus). The other guarantees the consensus happens not before the prescribed time instant. In the numerical example, a five-node multiagent system simulation validates the proposed prescribed-instant consensus.
- 7 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (5) , 4751-4761
A Novel High-Efficiency Three-Phase Multilevel PV Inverter With Reduced DC-Link Capacitance
In this article, we present a novel three-phase multilevel inverter (MLI) design for photovoltaic applications which does not require large dc-link capacitors to buffer the 120-Hz power ripple and allows individual inverter module to process trapezoidal power instead of sinusoidal power. This new design features two inverters connected in parallel to each dc source and N inverters connected in series to each grid phase to support the grid voltage. The trapezoidal operation improves the overall system’s efficiency by allowing the inverter module to output peak or zero power for most of the ac cycle. We present the controller design and simulate the proposed MLI system in power electronics simulation software (PLECS). We demonstrate an experimental 110-V dc input, 208 $V_{\text{rms}}$ three-phase ac output, and 1-kW five-level prototype with $>$ 95% efficiency. With the same inverter module, we compare the efficiency of the proposed design to the conventional MLI design, where all modules share phase power evenly. We demonstrate that the proposed design consistently outperforms the conventional design in efficiency, with $>$ 20% loss reduction at light load conditions.
- 7 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (5) , 4751-4761
A Novel High-Efficiency Three-Phase Multilevel PV Inverter With Reduced DC-Link Capacitance
In this article, we present a novel three-phase multilevel inverter (MLI) design for photovoltaic applications which does not require large dc-link capacitors to buffer the 120-Hz power ripple and allows individual inverter module to process trapezoidal power instead of sinusoidal power. This new design features two inverters connected in parallel to each dc source and N inverters connected in series to each grid phase to support the grid voltage. The trapezoidal operation improves the overall system’s efficiency by allowing the inverter module to output peak or zero power for most of the ac cycle. We present the controller design and simulate the proposed MLI system in power electronics simulation software (PLECS). We demonstrate an experimental 110-V dc input, 208 $V_{\text{rms}}$ three-phase ac output, and 1-kW five-level prototype with $>$ 95% efficiency. With the same inverter module, we compare the efficiency of the proposed design to the conventional MLI design, where all modules share phase power evenly. We demonstrate that the proposed design consistently outperforms the conventional design in efficiency, with $>$ 20% loss reduction at light load conditions.
- Open Access
- 16 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 2, 582-590
Fixed-Frequency Control of Piezoelectric Resonator DC-DC Converters for Spurious Mode Avoidance
Piezoelectric resonators have shown promise as efficient, power-dense energy storage element alternatives to continue the miniaturization of DC-DC converters. However, practical piezoelectric resonators diverge from their ideal behavior due to spurious modes that cause high loss regions throughout their operating frequency range. Typically, control of piezoelectric resonator DC-DC converters is constrained to unidirectional power flow each resonant cycle for maximum efficiency operation. However, output power depends on the frequency with such control, which means the converter cannot operate at loads corresponding to spurious mode frequencies. This paper presents a fixed-frequency control mode utilizing the high-quality factor of piezoelectric resonators to avoid spurious modes. The fixed-frequency control enables efficient operation spanning the converter's full load range, demonstrated through a prototype DC-DC converter with a custom fabricated lithium niobate resonator. At a conversion ratio of 60 V to 30 V, spurious modes limit the converter's operating range from 33 W to 51 W using unidirectional power-constrained control, yet the fixed-frequency control extends operation from 33 W to 2 W.
- 16 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 2, 582-590
Open AccessFixed-Frequency Control of Piezoelectric Resonator DC-DC Converters for Spurious Mode Avoidance
Piezoelectric resonators have shown promise as efficient, power-dense energy storage element alternatives to continue the miniaturization of DC-DC converters. However, practical piezoelectric resonators diverge from their ideal behavior due to spurious modes that cause high loss regions throughout their operating frequency range. Typically, control of piezoelectric resonator DC-DC converters is constrained to unidirectional power flow each resonant cycle for maximum efficiency operation. However, output power depends on the frequency with such control, which means the converter cannot operate at loads corresponding to spurious mode frequencies. This paper presents a fixed-frequency control mode utilizing the high-quality factor of piezoelectric resonators to avoid spurious modes. The fixed-frequency control enables efficient operation spanning the converter's full load range, demonstrated through a prototype DC-DC converter with a custom fabricated lithium niobate resonator. At a conversion ratio of 60 V to 30 V, spurious modes limit the converter's operating range from 33 W to 51 W using unidirectional power-constrained control, yet the fixed-frequency control extends operation from 33 W to 2 W.
- 24 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (6) , 5724-5734
Wideband PPT Class $\Phi _2$ Inverter Using Phase-Switched Impedance Modulation and Reactance CompensationClass $\boldsymbol{\Phi _2}$ is a suitable power amplifier (PA) topology for applications that demand low device voltage stress and simple gate driving. The push–pull with T network (PPT) version of this architecture can be advantageous over a conventional single-ended $\boldsymbol{\Phi _2}$ due to higher power capabilities through interleaving and simple closed-form design equations. The downside with this and many other switch-mode PAs is that they perform efficiently only at a single frequency with the power degrading outside the nominal point of operation. To improve upon this issue, we incorporate a phase-switched impedance modulation variable capacitor and a reactance compensation network so that the PPT $\boldsymbol{\Phi _2}$ can function across broadband. We experimentally demonstrate a 300-W PA for a 50- ${\Omega }$ load impedance using silicon devices. The PA achieves above 90% efficiency over approximately a 30% fractional bandwidth. The PA can also operate across broadband with light loads, where above 80% efficiency is maintained for up to five times higher load resistances. This switch-mode PA is one of the first to demonstrate such performance under load variation and across a wide bandwidth.
- 24 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (6) , 5724-5734
Wideband PPT Class $\Phi _2$ Inverter Using Phase-Switched Impedance Modulation and Reactance CompensationClass $\boldsymbol{\Phi _2}$ is a suitable power amplifier (PA) topology for applications that demand low device voltage stress and simple gate driving. The push–pull with T network (PPT) version of this architecture can be advantageous over a conventional single-ended $\boldsymbol{\Phi _2}$ due to higher power capabilities through interleaving and simple closed-form design equations. The downside with this and many other switch-mode PAs is that they perform efficiently only at a single frequency with the power degrading outside the nominal point of operation. To improve upon this issue, we incorporate a phase-switched impedance modulation variable capacitor and a reactance compensation network so that the PPT $\boldsymbol{\Phi _2}$ can function across broadband. We experimentally demonstrate a 300-W PA for a 50- ${\Omega }$ load impedance using silicon devices. The PA achieves above 90% efficiency over approximately a 30% fractional bandwidth. The PA can also operate across broadband with light loads, where above 80% efficiency is maintained for up to five times higher load resistances. This switch-mode PA is one of the first to demonstrate such performance under load variation and across a wide bandwidth.
- Open Access
- 18 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 2, 212-224
Optimized Resonators for Piezoelectric Power Conversion
The performance of inductors at high frequencies and small sizes is one of the largest limiting factors in the continued miniaturization of dc-dc converters. Piezoelectric resonators can have a very high quality factor and provide an inductive impedance between their series and parallel resonant frequencies, making them a promising technology for further miniaturizing dc-dc converters. In this paper we analyze the impact of resonator parameters on the performance of the piezoelectric resonator based dc-dc converter, derive the optimal load impedance and efficiency limits, and analyze the impacts of varying conversion ratio and load impedance. This work is accompanied by a prototype dc-dc converter using a piezoelectric resonator fabricated from lithium niobate. The piezoelectric resonator has a quality factor of 4178 and a coupling coefficient, k t 2 , of 29%. The converter is able to achieve high efficiency zero voltage switching and a continuously variable conversion ratio without the use of any discrete inductors. It achieves a maximum power output of 30.9 W at an efficiency of 95.2% with a power density of 6.76 W/cm 3 .
- 18 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 2, 212-224
Open AccessOptimized Resonators for Piezoelectric Power Conversion
The performance of inductors at high frequencies and small sizes is one of the largest limiting factors in the continued miniaturization of dc-dc converters. Piezoelectric resonators can have a very high quality factor and provide an inductive impedance between their series and parallel resonant frequencies, making them a promising technology for further miniaturizing dc-dc converters. In this paper we analyze the impact of resonator parameters on the performance of the piezoelectric resonator based dc-dc converter, derive the optimal load impedance and efficiency limits, and analyze the impacts of varying conversion ratio and load impedance. This work is accompanied by a prototype dc-dc converter using a piezoelectric resonator fabricated from lithium niobate. The piezoelectric resonator has a quality factor of 4178 and a coupling coefficient, k t 2 , of 29%. The converter is able to achieve high efficiency zero voltage switching and a continuously variable conversion ratio without the use of any discrete inductors. It achieves a maximum power output of 30.9 W at an efficiency of 95.2% with a power density of 6.76 W/cm 3 .
- 5 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (3) , 2456-2460
6.78-MHz Wireless Power Transfer With Self-Resonant Coils at 95% DC–DC Efficiency
Megahertz-frequency inductive wireless power transfer holds the promise of compact and efficient wireless power transfer. Unfortunately, due to high-frequency losses in wide-bandgap semiconductors and low-Q high-frequency coil designs, these systems are universally less efficient, on a dc-dc basis, than wireless power systems operating at conventional frequency regimes. This letter describes the design considerations for inductive wireless power transfer systems operating at 6.78 MHz. With a novel high-frequency resonant amplifier topology, a high-Q self-resonant coil structure, and a better understanding of C oss losses in wide-bandgap power semiconductors, we demonstrate 6.78- MHz wireless power transfer systems that achieve 95% dc-dc efficiency at power levels up to and beyond 1 kW.
- 5 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (3) , 2456-2460
6.78-MHz Wireless Power Transfer With Self-Resonant Coils at 95% DC–DC Efficiency
Megahertz-frequency inductive wireless power transfer holds the promise of compact and efficient wireless power transfer. Unfortunately, due to high-frequency losses in wide-bandgap semiconductors and low-Q high-frequency coil designs, these systems are universally less efficient, on a dc-dc basis, than wireless power systems operating at conventional frequency regimes. This letter describes the design considerations for inductive wireless power transfer systems operating at 6.78 MHz. With a novel high-frequency resonant amplifier topology, a high-Q self-resonant coil structure, and a better understanding of C oss losses in wide-bandgap power semiconductors, we demonstrate 6.78- MHz wireless power transfer systems that achieve 95% dc-dc efficiency at power levels up to and beyond 1 kW.
- Open Access
- 17 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10515-10531
Push–Pull Class $\Phi _{\text{2}}$ RF Power AmplifierThe Class $\Phi_2/\text{EF}_2$ amplifier is an attractive topology for high-voltage and high-frequency power conversion because of the high efficiency, reduced device voltage stress, simplicity of gate driving, and load-independent ZVS operation. Due to many degrees of freedom for tuning, previous studies can only solve the single-ended $\Phi_2$ circuit using numerical methods. This work focuses on improving the design and operating characteristics of a push-pull $\Phi_2$ amplifier with a $T$ network connected between the switch nodes, or a PPT $\Phi_2$ amplifier. The PPT $\Phi_2$ amplifier has less circulating energy and achieves higher cut-off frequency $\mathcal{f}_T$ than other $\Phi_2/\text{EF}_2$ circuits. We then present a series-stacked input configuration to reduce the switch voltage stress and improve the efficiency and power density. A compact 6.78 MHz, 100 V, 300 W prototype converter is demonstrated that uses low-cost Si devices and achieves 96% peak total efficiency and maintains above 94.5% drain efficiency across a wide range of voltage and power. Together with the advances in wide-bandgap semiconductors and magnetic materials, the PPT $\Phi_2$ circuit opens more possibilities for the state-of-the-art performance of solid-state RF amplifiers in high-frequency, high-power applications, including wireless charging for electric vehicles, plasma RF drives, and nuclear magnetic resonance (NMR) spectroscopy.- 17 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10515-10531
Open AccessPush–Pull Class $\Phi _{\text{2}}$ RF Power AmplifierThe Class $\Phi_2/\text{EF}_2$ amplifier is an attractive topology for high-voltage and high-frequency power conversion because of the high efficiency, reduced device voltage stress, simplicity of gate driving, and load-independent ZVS operation. Due to many degrees of freedom for tuning, previous studies can only solve the single-ended $\Phi_2$ circuit using numerical methods. This work focuses on improving the design and operating characteristics of a push-pull $\Phi_2$ amplifier with a $T$ network connected between the switch nodes, or a PPT $\Phi_2$ amplifier. The PPT $\Phi_2$ amplifier has less circulating energy and achieves higher cut-off frequency $\mathcal{f}_T$ than other $\Phi_2/\text{EF}_2$ circuits. We then present a series-stacked input configuration to reduce the switch voltage stress and improve the efficiency and power density. A compact 6.78 MHz, 100 V, 300 W prototype converter is demonstrated that uses low-cost Si devices and achieves 96% peak total efficiency and maintains above 94.5% drain efficiency across a wide range of voltage and power. Together with the advances in wide-bandgap semiconductors and magnetic materials, the PPT $\Phi_2$ circuit opens more possibilities for the state-of-the-art performance of solid-state RF amplifiers in high-frequency, high-power applications, including wireless charging for electric vehicles, plasma RF drives, and nuclear magnetic resonance (NMR) spectroscopy. - 19 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (6) , 6340-6349
Cascode GaN/SiC: A Wide-Bandgap Heterogenous Power Device for High-Frequency Applications
Wireless power transfer systems and plasma generators are among the increasing number of applications that use high-frequency power converters. Increasing switching frequency can reduce the energy storage requirements of the passive elements that can lead to higher power densities or even the elimination of magnetic cores. However, operating at higher frequencies requires faster switching devices in packages with low-parasitics. Wide bandgap (WBG) power devices like Gallium Nitride (GaN) and Silicon Carbide (SiC) devices, have high critical fields and high thermal conductivity that make them good candidates for efficient high-voltage and high-frequency operations. Commercially available GaN and SiC devices have ratings targeting different applications. Lateral GaN devices dominate in lower-voltage (<650 V) and high-frequency applications as they have relatively small device capacitances ( ${C_{oss},C_{iss}}$ ), which make them easy to drive at high frequencies. On the other hand, vertical SiC devices are often used in higher-voltage and lowfrequency applications since they have higher blocking voltages and larger gate charge than their GaN counterparts. As a result, SiC devices usually require high-power and complicated gate drive circuitry. Recent work shows that in both GaN and SiC devices, losses in device ${C_{oss}$ can exceed the conduction losses at high switching frequencies and relatively high voltages under Zero-Voltage-Switching (ZVS) conditions. Moreover, the ${C_{oss}$ energy loss ( ${E_{oss}$ ) per switching cycle increases with frequency in GaN devices but remains roughly independent of frequency in SiC devices. This means that at high frequencies, SiC devices can be preferable due to their smaller ${C_{oss}$ energy loss even when taking into consideration the complexity of the gate drive circuit. In this paper, we present a WBG high-voltage cascode GaN/SiC power device, combining the advantages of both a GaN and a SiC device - namely, simple gate drive requirements, ${E_{oss}$ loss per cycle roughly independent of frequency, and relatively high voltage blocking capability. Comparing this cascode GaN/SiC device with a SiC MOSFET and a SiC JFET of similar voltage ratings and ${R_{ds,ON}$ , we find that the inverter using the cascode GaN/SiC device has the highest efficiency and simplest auxiliary gate drive circuitry. Finally, integrating the cascode GaN/SiC device has the potential benefits of achieving lower ${C_{oss}$ losses, higher device ratings, and better heat removal capability.- 19 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (6) , 6340-6349
Cascode GaN/SiC: A Wide-Bandgap Heterogenous Power Device for High-Frequency Applications
Wireless power transfer systems and plasma generators are among the increasing number of applications that use high-frequency power converters. Increasing switching frequency can reduce the energy storage requirements of the passive elements that can lead to higher power densities or even the elimination of magnetic cores. However, operating at higher frequencies requires faster switching devices in packages with low-parasitics. Wide bandgap (WBG) power devices like Gallium Nitride (GaN) and Silicon Carbide (SiC) devices, have high critical fields and high thermal conductivity that make them good candidates for efficient high-voltage and high-frequency operations. Commercially available GaN and SiC devices have ratings targeting different applications. Lateral GaN devices dominate in lower-voltage (<650 V) and high-frequency applications as they have relatively small device capacitances ( ${C_{oss},C_{iss}}$ ), which make them easy to drive at high frequencies. On the other hand, vertical SiC devices are often used in higher-voltage and lowfrequency applications since they have higher blocking voltages and larger gate charge than their GaN counterparts. As a result, SiC devices usually require high-power and complicated gate drive circuitry. Recent work shows that in both GaN and SiC devices, losses in device ${C_{oss}$ can exceed the conduction losses at high switching frequencies and relatively high voltages under Zero-Voltage-Switching (ZVS) conditions. Moreover, the ${C_{oss}$ energy loss ( ${E_{oss}$ ) per switching cycle increases with frequency in GaN devices but remains roughly independent of frequency in SiC devices. This means that at high frequencies, SiC devices can be preferable due to their smaller ${C_{oss}$ energy loss even when taking into consideration the complexity of the gate drive circuit. In this paper, we present a WBG high-voltage cascode GaN/SiC power device, combining the advantages of both a GaN and a SiC device - namely, simple gate drive requirements, ${E_{oss}$ loss per cycle roughly independent of frequency, and relatively high voltage blocking capability. Comparing this cascode GaN/SiC device with a SiC MOSFET and a SiC JFET of similar voltage ratings and ${R_{ds,ON}$ , we find that the inverter using the cascode GaN/SiC device has the highest efficiency and simplest auxiliary gate drive circuitry. Finally, integrating the cascode GaN/SiC device has the potential benefits of achieving lower ${C_{oss}$ losses, higher device ratings, and better heat removal capability.- 6 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 8 (3) , 2268-2275
Effect of Class 2 Ceramic Capacitor Variations on Switched-Capacitor and Resonant Switched-Capacitor Converters
Class 2 ceramic capacitors, such as X7R, have relatively high energy density compared to Class 1 ceramic capacitors. However, they experience changes due to aging, temperature, and electric field. The measured X7R capacitance drop is 1-2% per decade hour due to aging, 18% due to a temperature change from 25°C to 125°C, and 75% due to an applied voltage that is 80% of the rated voltage. The measured equivalent series resistance (ESR) of the X7R capacitors show an increase of 20% to 70% due to aging of 1680 hours, and a 50% fluctuation in value when we apply 20% to 80% of the rated voltage. In switched capacitor (SC) and resonant switched capacitor (ReSC) converters, these variations can shift a converter’s operating point and result in higher equivalent output resistance and lower efficiency.We quantified the converter performance degradation caused by capacitor variations in simulation and demonstrated the results by implementing a 1 MHz 25 W 1:4 Dickson ReSC converter. The converter efficiency decreases from 93.1% to 90.7% as a result of capacitor variations mainly due to aging effect.
- 6 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 8 (3) , 2268-2275
Effect of Class 2 Ceramic Capacitor Variations on Switched-Capacitor and Resonant Switched-Capacitor Converters
Class 2 ceramic capacitors, such as X7R, have relatively high energy density compared to Class 1 ceramic capacitors. However, they experience changes due to aging, temperature, and electric field. The measured X7R capacitance drop is 1-2% per decade hour due to aging, 18% due to a temperature change from 25°C to 125°C, and 75% due to an applied voltage that is 80% of the rated voltage. The measured equivalent series resistance (ESR) of the X7R capacitors show an increase of 20% to 70% due to aging of 1680 hours, and a 50% fluctuation in value when we apply 20% to 80% of the rated voltage. In switched capacitor (SC) and resonant switched capacitor (ReSC) converters, these variations can shift a converter’s operating point and result in higher equivalent output resistance and lower efficiency.We quantified the converter performance degradation caused by capacitor variations in simulation and demonstrated the results by implementing a 1 MHz 25 W 1:4 Dickson ReSC converter. The converter efficiency decreases from 93.1% to 90.7% as a result of capacitor variations mainly due to aging effect.