ASAlexander B. Straumal

Alexander B. Straumal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Alexander B. Straumal has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High Entropy Alloys for Energy Conversion and Storage: A Review of Grain Boundary Wetting Phenomena

    by Boris Straumal, Anna Korneva, Alexei Kuzmin, Leonid Klinger, Gabriel A. Lopez, Nikolai Vershinin, Alexander Straumal, Alena Gornakova

    The multicomponent alloys with nearly equal concentration of components, also known as high entropy alloys (HEAs), were first proposed 22 years ago. The HEAs quickly became very important in materials science due to their unique properties. Nowadays, the HEAs are frequently used in energy conversion and storage applications. HEAs can consist of five, six or more components. Plasma cladding permits coating of the large surfaces of cheap substrates with (often expensive) HEAs and to enlarge, in such a way, their application area. The large-area coatings deposited by plasma cladding possess multiple advantages such as low thermal distortion, very high energy density, as well as low dilution of the substrate material. Plasma cladding ensures good metallurgical bonding between coating and substrate. The costs of operation and equipment are also very attractive. During plasma cladding, the mixed powders are blown by carrier gas into a plasma torch or are positioned on a substrate. This powder mixture is then melted in or under the plasma torch. The plasma torch, in turn, sequentially scans the substrate. After finalizing the crystallization process, the solid polycrystal appears which contains few residual melts. This remaining melt can completely or incompletely wet the grain boundaries (GBs) in solid phase of the polycrystal. These completely or incompletely wetted GBs can strongly influence the microstructure of HEA coatings and their morphology. In this review we analyze the GB wetting HEAs containing one phase in HEAs with two, three and more phases, as well as in HEAs reinforced with particles of carbides, nitrides, borides, or oxides. We also analyze the microstructure of the rather thick coatings after plasma cladding after additional laser remelting and observe how GB wetting changes over their thickness.


  • Open Access

    High Entropy Alloys Coatings Deposited by Laser Cladding: A Review of Grain Boundary Wetting Phenomena

    by Boris B. Straumal, Leonid Klinger, Alexei Kuzmin, Gabriel A. Lopez, Anna Korneva, Alexander B. Straumal, Nikolai Vershinin, Alena S. Gornakova

    High-entropy alloys (HEAs) are called also alloys without a main component or multiprincipal alloys. They consist of five, six or more components in more or less equal proportions and possess unique properties. Several dozens of thousands of publications have already been devoted to bulk HEAs, while HEA coatings are just beginning to develop. More than half of the works on the deposition of HEA coatings are devoted to laser cladding. In the laser cladding process, a mixture of powders on a substrate is melted in a focused laser beam, which sequentially scans the substrate. In the heated zone, the powder mixture melts. At the end of the crystallization process, a solidified polycrystal and a small amount of residual melt are found in the heated zone. It is possible that the grain boundaries (GBs) in the solidified polycrystal are incompletely or fully wetted by this liquid phase. In this way, the GB wetting with a melt determines the morphology and microstructure of HEAs coatings. This review analyzes GB wetting in single-phase HEAs, as well as in HEAs containing two or more phases. We analyze how the HEAs’ composition, laser scanning speed, laser beam power, external magnetic field or ultrasonic impact affect the microstructure and GB wetting. It is also shown how the microstructure and GB wetting change over the thickness of the rather thick as well as multilayer coatings deposited using a laser cladding.


  • Open Access

    Grain Boundary Wetting Phenomena in High Entropy Alloys Containing Nitrides, Carbides, Borides, Silicides, and Hydrogen: A Review

    by Boris Straumal, Eugen Rabkin, Gabriel A. Lopez, Anna Korneva, Alexei Kuzmin, Alena Gornakova, Alexander Straumal, Brigitte Baretzky

    In this review, we analyze the structure of multicomponent alloys without principal components (they are also called high entropy alloys—HEAs), containing not only metals but also hydrogen, nitrogen, carbon, boron, or silicon. In particular, we discuss the phenomenon of grain boundary (GB) wetting by the melt or solid phase. The GB wetting can be complete or incomplete (partial). In the former case, the grains of the matrix are completely separated by the continuous layer of the second phase (solid or liquid). In the latter case of partial GB wetting, the second solid phase forms, between the matrix grains, a chain of (usually lenticular) precipitates or droplets with a non-zero value of the contact angle. To deal with the morphology of GBs, the new GB tie-lines are used, which can be constructed in the two- or multiphase areas of the multidimensional HEAs phase diagrams. The GBs in HEAs in the case of complete or partial wetting can also contain hydrides, nitrides, carbides, borides, or silicides. Thus, GB wetting by the hydrides, nitrides, carbides, borides, or silicides can be used in the so-called grain boundary chemical engineering in order to improve the properties of respective HEAs.


  • Open Access

    Grain Boundary Wetting by a Second Solid Phase in the High Entropy Alloys: A Review

    by Boris B. Straumal, Anna Korneva, Gabriel A. Lopez, Alexei Kuzmin, Eugen Rabkin, Gregory Gerstein, Alexander B. Straumal, Alena S. Gornakova

    In this review, the phenomenon of grain boundary (GB) wetting by the second solid phase is analyzed for the high entropy alloys (HEAs). Similar to the GB wetting by the liquid phase, the GB wetting by the second solid phase can be incomplete (partial) or complete. In the former case, the second solid phase forms in the GB of a matrix, the chain of (usually lenticular) precipitates with a certain non-zero contact angle. In the latter case, it forms in the GB continuous layers between matrix grains which completely separate the matrix crystallites. The GB wetting by the second solid phase can be observed in HEAs produced by all solidification-based technologies. The particle chains or continuous layers of a second solid phase form in GBs also without the mediation of a liquid phase, for example by solid-phase sintering or coatings deposition. To describe the GB wetting by the second solid phase, the new GB tie-lines should be considered in the two- or multiphase areas in the multicomponent phase diagrams for HEAs. The GB wetting by the second solid phase can be used to improve the properties of HEAs by applying the so-called grain boundary engineering methods.


  • Open Access

    The Grain Boundary Wetting Phenomena in the Ti-Containing High-Entropy Alloys: A Review

    by Boris B. Straumal, Anna Korneva, Alexei Kuzmin, Gabriel A. Lopez, Eugen Rabkin, Alexander B. Straumal, Gregory Gerstein, Alena S. Gornakova

    In this review, the phenomenon of grain boundary (GB) wetting by melt is analyzed for multicomponent alloys without principal components (also called high-entropy alloys or HEAs) containing titanium. GB wetting can be complete or partial. In the former case, the liquid phase forms the continuous layers between solid grains and completely separates them. In the latter case of partial GB wetting, the melt forms the chain of droplets in GBs, with certain non-zero contact angles. The GB wetting phenomenon can be observed in HEAs produced by all solidification-based technologies. GB leads to the appearance of novel GB tie lines Twmin and Twmax in the multicomponent HEA phase diagrams. The so-called grain-boundary engineering of HEAs permits the use of GB wetting to improve the HEAs’ properties or, alternatively, its exclusion if the GB layers of a second phase are detrimental.


  • Open Access

    Bulk and Surface Low Temperature Phase Transitions in the Mg-Alloy EZ33A

    by Alexander Straumal, Ivan Mazilkin, Kristina Tzoy, Boris Straumal, Krzysztof Bryła, Alexander Baranchikov, Gunther Eggeler

    Low-temperature phase transitions in the EZ33A Mg-cast alloy have been investigated. Based on the structure assessment of the alloy after annealing at 150 °C (1826 h) and at 200 °C (2371 h) a grain boundary wetting transition by a second solid phase was documented. Within a 50 °C temperature range, substantial differences in the α(Mg) grain boundary fraction wetted by the (Mg,Zn)12RE intermetallic were observed. In contrast to what was reported in the literature, two different types of precipitates were found within α(Mg) grains. With increasing annealing temperatures, both types of precipitates dissolved.


  • Grain boundary wetting of different types of grain boundaries in the Cu–Ag system

    by Ivan Mazilkin, Kristina Tsoy, Alexander Straumal, Alexey Rodin, Brigitte Baretzky


  • Comparison of Spectra of Grain Boundaries Spontaneously Formed in Cu-Ag and Cu-In Systems

    by A. B. Straumal, K. V. Tsoi, I. A. Mazilkin, A. O. Rodin, G. Eggeler

    Spectra of grain boundaries existing in the polycrystalline copper-silver system (positive enthalpy of mixing) have been studied in comparison with those of the copper-indium system (negative enthalpy of mixing). Spectra of grain boundaries are formed spontaneously upon an increase in the temperature, occurrence of eutectic and peritectic reactions, and subsequent relaxation of structures in the two-phase solid/liquid region of phase diagrams. It has been shown that the rate of grain growth and the relation between different grain boundary types in the total spectrum depend on the enthalpy of mixing.