Sebastian Nessler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sebastian Nessler has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Maximilian Marx
Department of Microsystems Engineering (IMTEK), Chair of Microelectronics, University of Freiburg, Freiburg, Germany
4 shared publications - Yiannos Manoli
Department of Microsystems (IMTEK), Laboratory for Microelectronics, University of Freiburg, Freiburg im Breisgau, Germany
4 shared publications - Daniel De Dorigo
Department of Microsystems (IMTEK), Laboratory for Microelectronics, University of Freiburg, Freiburg im Breisgau, Germany
2 shared publications - Armin Taschwer
Hahn-Schickard, Villingen-Schwenningen, Germany
1 shared publication Daniel De Dorigo
Department of Microsystems Engineering-IMTEK, Fritz Huettinger Chair of Microelectronics, University of Freiburg, 79085 Freiburg, Germany
1 shared publication- Matthias Kuhl
Department of Microsystems (IMTEK), Laboratory for Microelectronics, University of Freiburg, Freiburg im Breisgau, Germany
1 shared publication
Latest Publications
- 2 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 66 (5) , 743-747
An Automatic MEMS Gyroscope Mode Matching Circuit Based on Noise Observation
The performance of microelectromechanical system (MEMS) gyroscopes can be significantly enhanced by matching the resonance frequencies of the drive and sense mechanical resonators. However, the precise control of the resonance frequency in a closed loop readout circuit is challenging. This paper presents an automatic detection and control circuit, which performs a background tuning of the MEMS element. The tuning method is based on the observation of noise at the output of a continuous time Σ modulator readout circuit, so that no modification of the sense loop such as additional input force generation is required. Parasitic modulation of the sensor’s zero rate output due to the mode matching loop is canceled by an additional offset compensation circuit. The system is validated on an FPGA connected to a MEMS gyroscope and an ASIC readout circuit. The digital mode matching circuit would consume a power of 21μW on an area of 0.17 mm2 in a 0.35μm CMOS technology.
- 2 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 66 (5) , 743-747
An Automatic MEMS Gyroscope Mode Matching Circuit Based on Noise Observation
The performance of microelectromechanical system (MEMS) gyroscopes can be significantly enhanced by matching the resonance frequencies of the drive and sense mechanical resonators. However, the precise control of the resonance frequency in a closed loop readout circuit is challenging. This paper presents an automatic detection and control circuit, which performs a background tuning of the MEMS element. The tuning method is based on the observation of noise at the output of a continuous time Σ modulator readout circuit, so that no modification of the sense loop such as additional input force generation is required. Parasitic modulation of the sensor’s zero rate output due to the mode matching loop is canceled by an additional offset compensation circuit. The system is validated on an FPGA connected to a MEMS gyroscope and an ASIC readout circuit. The digital mode matching circuit would consume a power of 21μW on an area of 0.17 mm2 in a 0.35μm CMOS technology.
- 2 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (2) , 511-523
A 141- $\mu$ W High-Voltage MEMS Gyroscope Drive Interface Circuit Based on Flying CapacitorsElectronic readout circuits for microelectromechanical gyroscopes suffer from high power consumption caused by the electrostatic sensor actuation with signals above the standard chip supply voltage. This paper presents an electronic circuit principle and implementation, which exploits the fact that ac actuation signals in the range of the chip supply voltage are sufficient, if they are combined with a high-voltage (HV) dc biasing. Therefore, the developed system performs the generation of the time-varying signal in the low-voltage domain and uses precharged flying capacitors to efficiently add a high dc biasing voltage. The circuit consists of a closed-loop low ripple charge pump, low-voltage driver amplifier, and an HV common frame biasing amplifier. The fully on-chip implementation occupies an area of 0.58 mm² and reduces the power consumption to 141 μW.
- 2 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (2) , 511-523
A 141- $\mu$ W High-Voltage MEMS Gyroscope Drive Interface Circuit Based on Flying CapacitorsElectronic readout circuits for microelectromechanical gyroscopes suffer from high power consumption caused by the electrostatic sensor actuation with signals above the standard chip supply voltage. This paper presents an electronic circuit principle and implementation, which exploits the fact that ac actuation signals in the range of the chip supply voltage are sufficient, if they are combined with a high-voltage (HV) dc biasing. Therefore, the developed system performs the generation of the time-varying signal in the low-voltage domain and uses precharged flying capacitors to efficiently add a high dc biasing voltage. The circuit consists of a closed-loop low ripple charge pump, low-voltage driver amplifier, and an HV common frame biasing amplifier. The fully on-chip implementation occupies an area of 0.58 mm² and reduces the power consumption to 141 μW.
- 18 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (8) , 2298-2310
A 22 V Compliant 56 ${\mu}$ W Twin-Track Active Charge Balancing Enabling 100% Charge Compensation Even in Monophasic and 36% Amplitude Correction in Biphasic Neural StimulatorsClosed-loop charge balancers make a considerable contribution to a safe and secure electrical stimulation and additionally present an alternative to bulky blocking capacitors. This CMOS-integrated, 22 V compliant Twin-Track active charge balancer accomplishes both instantaneous and long-term balanced conditions. Long-term charge balancing is achieved by a cause-based PI-controlled offset compensation of the remaining electrode voltage. A Gm of only 1.5 nS offers a large (8 ms) time constant with only a 12 pF capacitor and leads to the first integrated PI-controller for offset compensation in neural implants. Instantaneous autonomous balancing is realized by a second concept, the consequence-based Inter-Pulse Charge Control. It uses a class-B architecture to supply the compensation currents. Thus, no additional references are required to define the safety window of the remaining electrode voltage. It consumes 31.8 μW in the idle state, while the delivered output power can be as high as 11 mW. The two complementary approaches can be combined to one system, providing the opportunity to achieve a better performance. The system consumes 56 μW and features a 36% mismatch correction in biphasic stimuli amplitude, as well as an autonomous 100% charge removal at maximum compensation amplitudes of 500 μA, which makes it a suitable complement to monophasic stimulators.
- 18 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (8) , 2298-2310
A 22 V Compliant 56 ${\mu}$ W Twin-Track Active Charge Balancing Enabling 100% Charge Compensation Even in Monophasic and 36% Amplitude Correction in Biphasic Neural StimulatorsClosed-loop charge balancers make a considerable contribution to a safe and secure electrical stimulation and additionally present an alternative to bulky blocking capacitors. This CMOS-integrated, 22 V compliant Twin-Track active charge balancer accomplishes both instantaneous and long-term balanced conditions. Long-term charge balancing is achieved by a cause-based PI-controlled offset compensation of the remaining electrode voltage. A Gm of only 1.5 nS offers a large (8 ms) time constant with only a 12 pF capacitor and leads to the first integrated PI-controller for offset compensation in neural implants. Instantaneous autonomous balancing is realized by a second concept, the consequence-based Inter-Pulse Charge Control. It uses a class-B architecture to supply the compensation currents. Thus, no additional references are required to define the safety window of the remaining electrode voltage. It consumes 31.8 μW in the idle state, while the delivered output power can be as high as 11 mW. The two complementary approaches can be combined to one system, providing the opportunity to achieve a better performance. The system consumes 56 μW and features a 36% mismatch correction in biphasic stimuli amplitude, as well as an autonomous 100% charge removal at maximum compensation amplitudes of 500 μA, which makes it a suitable complement to monophasic stimulators.
- 10 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 65 (3) , 870-880
A Self-Test on Wafer Level for a MEM Gyroscope Readout Based on $\Delta \Sigma$ ModulationThis paper presents the implementation of a self-test for a gyroscope readout based on electro-mechanical ΔΣ modulation. Commonly, sensor element and readout ASIC are fabricated on separate wafers. Therefore, the ability to separately characterize the sensor element and the ASIC before packaging is desirable in order to reduce unnecessary expense. For the proposed self-test, a charge integrator with collocated detection and feedback is configured to generate an additional feedback path, which is used to operate a purely electrical ΔΣ modulator on wafer level. The self-test is performed in two steps. First, an automatic compensation controller configures the collocated force-feedback and thereby verifies its functionality. In a second step, an offset is added to the settled value of the controller to generate a negative feedback path to the input of the readout interface. The resulting purely electrical ΔΣ modulator is utilized to validate the functionality of every single circuit component of the later operated electro-mechanical ΔΣ modulator. The proposed self-test makes use of the already available hardware and therefore avoids an additional hardware overhead. Numerical simulations are performed to verify the proposed compensation controller concept as well as the self-test itself. The simulation results of the self-test are confirmed by measurements.
- 10 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 65 (3) , 870-880
A Self-Test on Wafer Level for a MEM Gyroscope Readout Based on $\Delta \Sigma$ ModulationThis paper presents the implementation of a self-test for a gyroscope readout based on electro-mechanical ΔΣ modulation. Commonly, sensor element and readout ASIC are fabricated on separate wafers. Therefore, the ability to separately characterize the sensor element and the ASIC before packaging is desirable in order to reduce unnecessary expense. For the proposed self-test, a charge integrator with collocated detection and feedback is configured to generate an additional feedback path, which is used to operate a purely electrical ΔΣ modulator on wafer level. The self-test is performed in two steps. First, an automatic compensation controller configures the collocated force-feedback and thereby verifies its functionality. In a second step, an offset is added to the settled value of the controller to generate a negative feedback path to the input of the readout interface. The resulting purely electrical ΔΣ modulator is utilized to validate the functionality of every single circuit component of the later operated electro-mechanical ΔΣ modulator. The proposed self-test makes use of the already available hardware and therefore avoids an additional hardware overhead. Numerical simulations are performed to verify the proposed compensation controller concept as well as the self-test itself. The simulation results of the self-test are confirmed by measurements.
- 20 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (1) , 174-186
A 27 $\mu \text{W}$ 0.06 mm2 Background Resonance Frequency Tuning Circuit Based on Noise Observation for a 1.71 mW CT- $\Delta \Sigma $ MEMS Gyroscope Readout System With 0.9 °/h Bias InstabilityThis paper presents the implementation of a bandpass filter tuning circuit solely based on noise observation for a continuous-time (CT) delta-sigma modulator gyroscope readout system. By evaluating the noise at the electronic filter input, a filter frequency deviation of less than 50 Hz or approximately 0.5% of the gyroscope's drive resonance frequency is achieved, which minimizes the angular rate noise floor. The automatic tuning works in the background during normal angular rate readout with input signals up to the full scale, over a temperature range of 115 °C, and with interference signals of up to -27.2 dBFS. The power (27 μW) and area (0.06 mm²) overhead to the overall system is less than 2%. The overall CT readout system achieves a noise floor of 0.002 °/s/√Hz and a bias instability of 0.9 °/h while consuming only 1.71 mW.
- 20 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (1) , 174-186
A 27 $\mu \text{W}$ 0.06 mm2 Background Resonance Frequency Tuning Circuit Based on Noise Observation for a 1.71 mW CT- $\Delta \Sigma $ MEMS Gyroscope Readout System With 0.9 °/h Bias InstabilityThis paper presents the implementation of a bandpass filter tuning circuit solely based on noise observation for a continuous-time (CT) delta-sigma modulator gyroscope readout system. By evaluating the noise at the electronic filter input, a filter frequency deviation of less than 50 Hz or approximately 0.5% of the gyroscope's drive resonance frequency is achieved, which minimizes the angular rate noise floor. The automatic tuning works in the background during normal angular rate readout with input signals up to the full scale, over a temperature range of 115 °C, and with interference signals of up to -27.2 dBFS. The power (27 μW) and area (0.06 mm²) overhead to the overall system is less than 2%. The overall CT readout system achieves a noise floor of 0.002 °/s/√Hz and a bias instability of 0.9 °/h while consuming only 1.71 mW.