JFJoão Paulo Cosas Fernandes

João Paulo Cosas Fernandes

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


João Paulo Cosas Fernandes has a total of 67 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Decoupling Phase-specific and Interphases Mechanical Behaviors of Filled Elastomeric Blends under Strain

    by João Paulo Cosas Fernandes, Carlos E. Federico, Marc Weydert, Roberto Quintana

    Understanding the mechanical behavior of multi-phase polymer blends and nanocomposites requires separating the contributions of individual phases under strain. In this work, we present a methodology combining in-situ micro-tensile testing with Atomic Force Microscopy (AFM) and Digital Image Correlation (DIC) to analyze phase-specific responses in filled elastomeric blends. Polyisoprene/polybutadiene (PI/BR) blends with varying vulcanization systems and carbon black (CB) contents were studied as model systems. Sequential AFM images were acquired at different levels of applied tensile true strain and processed by DIC to quantify local strain, revealing distinct responses of the each of the phases. The rubber–rubber interphase was characterized in terms of thickness and local strain up to 25% macroscopic tensile true strain, revealing a broad distribution, indicating uneven solicitation across interphases. The average local strain at the interphase also varied with vulcanization system and CB content, underlining the effect of formulation parameters. This combined AFM–DIC methodology enables quantitative, nanoscale investigation of phase-specific mechanical behavior and interphase properties, comprehensive insights into the strain-dependent mechanical performance of elastomeric blends and nanocomposites.

  • Co-localized AFM/Raman characterization of multiphase polymer systems

    by Joao Paulo Cosas Fernandes

    Co-localisation AFM/Raman : caractérisation de systèmes polymères multiphasés: L’étude avancée de systèmes polymères complexes (mélanges compatibilisés, nanocomposites, copolymères à bloc, etc) est cruciale pour le développement de nouvelles solutions d'ingénierie. Afin d'élucider les relations mise en œuvre-structure-propriétés de ces systèmes, la co-localisation d’informations chimique, physique et morphologique devient essentielle pour obtenir des réponses fiables. La caractérisation de la surface et de l’intérieur des matériaux est également d'une importance primordiale, en particulier pour les matériaux polymères minces (<100 μm) tels que les membranes, qui peuvent présenter des profils de propriétés contrastés entre les surfaces et le coeur. Ces profils de propriétés peuvent être induits par le procédé de mise en œuvre, la chimie du matériau ou son vieillissement. Pour cela, le matériau doit être correctement ouvert sans modification structurelle, chimique ou morphologique. Par conséquent, l'objectif principal de cette thèse a été de développer une méthodologie expérimentale de caractérisation alliant la co-localisation des informations morphologiques, nanomécaniques et chimiques obtenues par le couplage de la Microscopie de Force Atomique (AFM) et la Microspectroscopie Confocale Raman et d’une technique de préparation des coupes transversales par cryo-ultramicrotomie.La stratégie développée a été appliquée à trois systèmes polymères différents: 1) des mélanges polyamide 6 (PA6) / acrylonitrile-butadiène-styrène (ABS), compatibilisés avec un styrène-acrylonitrile greffé anhydride maléique (SAN-MA); 2) de membranes hybrides constituées d’une matrice polymère de type polyétheréthercétone sulfoné (sPEEK) et d’une phase inorganique chimiquement active préparée par chimie Sol-Gel (SG); 3) des copolymères à bloc de type PS-PEO-PS utilisés comme électrolytes pour les batteries lithium. L’étude morphologique du mélange PA/ABS a montré que l'addition d’un copolymère SAN-MA améliore significativement la dispersion de la phase ABS dans la matrice PA et, en fonction du protocole appliqué, modifie la morphologie du mélange et la structure cristalline de la phase PA (teneur/distribution des phases -). Les modifications morphologiques observées ont ensuite été corrélées aux propriétés rhéologiques des mélanges. L’étude des membranes hybrides sPEEK/SG avait pour objectif de comprendre l’impact des étapes clés d’élaboration de ces membranes sur la morphologie des mélanges, la distribution de la phase SG dans la matrice sPEEK et sa densité de réticulation et le précurseur utilisé: (3-mercaptopropyl)-methyldimethoxysilane (SHDi) et (3-mercaptopropyl)-triméthoxysilane (SHTriM). L'efficacité des traitements thermiques appliqués aux différentes étapes du processus de fabrication des membranes SHDi a été démontrée. Pour les membranes basées sur le précurseur SHTriM, il a été démontré que la phase SG présente un système hiérarchiquement organisé, avec des domaines sphériques composés de particules élémentaires plus petites. L’inclusion d'une phase SG à l'intérieur de la membrane sPEEK ne perturbe pas la nanoséparation hydrophobe/hydrophile de la matrice, mais limite son gonflement. Enfin, une 'analyse morphologique a été réalisée sur une série de copolymères à bloc utilisés comme électrolytes polymères dans les batteries lithium. Le contraste nanomécanique des différentes phases a permis de mesurer les distances inter-domaine entre les phases PS et PEO par AFM et une bonne corrélation a été obtenu avec des résultats de diffusion de rayons X aux petits angles (SAXS). Il a été démontré que les propriétés nanomécaniques de surface du matériau évoluent avec son hydratation (humidité relative de la pièce).Dans chacune des trois études présentées dans cette thèse, la stratégie de co-localisation et a fourni des informations précieuses inaccessibles autrement. Cela ne fut possible qu'après une mise en œuvre spécifique de la cryo-ultramicrotomie pour la coupe de membranes fines et d’échantillons sensibles à l'eau.

  • Open Access

    Valorization of kombucha SCOBY waste: Developing a natural rubber and bacterial cellulose biocomposite

    by Fernanda de Andrade Buás Campeão, Cléverson Fernandes Senra Gabriel, Gustavo Ninho Campos, João Paulo Cosas Fernandes, Elisson Brum Dutra da Rocha, Kelly Alencar Silva, Gizele Cardoso Fontes Sant`aNa, Ana Maria Furtado de Sousa

  • Open Access

    Assessment of the Mixing Procedure and the Effect of Carboxylated Nitrile Rubber as a Compatibilizer for Kraft Lignin/Nitrile Rubber Composites

    by Nicoly Rosario da Costa, Gustavo Ninho Campos, Elisson Brum Dutra da Rocha, João Paulo Cosas Fernandes, Ana Maria Furtado de Sousa

    The growing interest in sustainable rubber materials motivates the use of renewable resources for the development of advanced materials. Lignin, valued for its abundance, biodegradability, and mechanical strengths, emerges as a promising alternative filler in rubber composites. This study produced composites using nitrile rubber (NBR) and a 70:30 blend of NBR with carboxylated nitrile rubber (XNBR), each incorporating 40 parts per hundred of rubber (phr) of kraft lignin. Two methods were tested for incorporating lignin: direct addition of 40 phr of lignin powder to the rubbers or compounding using masterbatches of NBR/lignin and XNBR/lignin, each with 130 phr of lignin produced by co‐coagulation. Results revealed that NBR/XNBR/lignin composites show thinner, more aligned lignin particles than NBR/lignin composites, with the masterbatch technique further reducing particle size. All lignin‐filled rubbers exhibited an increased reaction rate constant of vulcanization, lower covalent crosslink density, and higher ionic crosslink density compared to unfilled rubber. Notably, composites made with lignin masterbatch exhibited a reduced Payne effect, as well as higher tensile and tear strengths, than those made using lignin powder. These findings suggest that incorporating lignin via a masterbatch and blending with XNBR offers a compelling strategy for enhancing the properties of NBR‐based rubber composites.


  • Heat exchange and damage of carbon black‐filled styrene‐butadiene rubber under uniaxial cyclic loading

    by Nicolas Candau, João Paulo Cosas Fernandes, Eduard Vives, Miguel Mudarra Lopez, Marc Neira‐Viñas, Maria Lluisa Maspoch

    In this paper, we present an original experimental approach combining infrared thermography, analysis of voiding, and swelling tests to investigate damage mechanisms in carbon black (CB)‐filled styrene‐butadiene rubber (SBR). Heat exchange and voiding under uniaxial cyclic loading have been observed. A mechanical and electrical percolating filler network was identified by atomic force microscopy and electrical conductivity for the SBR with highest content of fillers (60 phr). SBR materials with a non percolating filler network show a reversible thermal energy dissipation during a series of cyclic loading, concomitant with reversible voiding mechanisms, through the successive formation and closing of voids. The SBR with the percolating network undergoes, during the series of cyclic loading, a high dissipation of energy under the form of heat, concomitantly with irreversible voiding mechanisms. Such mechanisms are shown to be due primarily to (i) the alteration of the filler network and/or filler/rubber interface and to a lower extent to (ii) the rubber matrix alteration (chains scission and/or crosslink breakage) as demonstrated by ex‐situ swelling.


  • Cellulose nanocrystals as nucleating agents for the strain induced crystallization in natural rubber

    by Nicolas Candau, João Paulo Cosas Fernandes, Emilien Vasmer, Maria Lluisa Maspoch

    Dispersed cellulose nanocrystals enhance strain induced crystallization in the natural rubber matrix and lead to improved elastocaloric performance.


  • Open Access

    An Investigation on the Thermally Induced Compatibilization of SBR and α-Methylstyrene/Styrene Resin

    by Arnaud Wolf, João Paulo Cosas Fernandes, Chuanyu Yan, Reiner Dieden, Laurent Poorters, Marc Weydert, Pierre Verge

    The miscibility between two polymers such as rubbers and performance resins is crucial to achieve given targeted properties in terms of tire performances. To this aim, α-methylstyrene/styrene resin (poly(αMSt-co-St)) are used to modify the viscoelastic behavior of rubbers and to fulfill the requirements of the final applications. The initial aim of this work was to understand the influence of poly(αMSt-co-St) resins blended at different concentrations in a commercial styrene-butadiene rubber (SBR). Interestingly, while studying the viscoelastic properties of SBR blends with poly(αMSt-co-St), crosslinking of the rubber was observed under conditions where it was not expected to happen. Surprisingly, after the crosslinking reactions, the poly(αMSt-co-St) resin was irreversibly miscible with SBR at concentrations far above its immiscibility threshold. A detailed investigation involving characterization technics including solid state nuclear magnetic resonance led to the conclusion that poly(αMSt-co-St) is depolymerizing under heating and can graft onto the chains of SBR. It results in an irreversible compatibilization mechanism between the rubber and the resin.


  • Open Access

    Synthesis of Novel Benzoxazines Containing Sulfur and Their Application in Rubber Compounds

    by Acerina Trejo-Machin, João Paulo Cosas Fernandes, Laura Puchot, Suzanne Balko, Marcel Wirtz, Marc Weydert, Pierre Verge

    This work reports the synthesis and successful use of novel benzoxazines as reinforcing resins in polyisoprene rubber compounds. For this purpose, three new dibenzoxazines containing one (4DTP-fa) or two heteroatoms of sulfur (3DPDS-fa and 4DPDS-fa) were synthesized following a Mannich condensation reaction. The structural features of each benzoxazine precursor were characterized by 1H and 13C nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR) and Raman. The new precursors showed well suited reactivity as characterized by differential scanning calorimetry (DSC) and rheology and were incorporated in rubber compounds. After the mixing, the curing profiles, morphologies and mechanical properties of the materials were tested. These results show that the structural feature of each isomer was significantly affecting its behavior during the curing of the rubber compounds. Among the tested benzoxazines, 3DPDS-fa exhibited the best ability to reinforce the rubber compound even compared to common phenolic resin. These results prove the feasibility to reinforce rubber compounds with benzoxazine resins as a possible alternative to replace conventional phenolic resins. This paper provides the first guide to use benzoxazines as reinforcing resins for rubber applications, based on their curing kinetics.


  • Open Access

    Unveiling the multiscale morphology of chemically stabilized proton exchange membranes for fuel cells by means of Fourier and real space studies

    by Natacha Huynh, João Paulo Cosas Fernandes, Vincent H. Mareau, Laurent Gonon, Stéphanie Pouget, Pierre-Henri Jouneau, Lionel Porcar, Hakima Mendil-Jakani

    Deciphering the multiscale morphology of a new generation of hybrid membranes for PEMFC applications showing promising performances and durability.


  • Open Access

    Fused Metalloporphyrin Thin Film with Tunable Porosity via Chemical Vapor Deposition

    by Kamal Baba, Giuseppe Bengasi, François Loyer, Joao Paulo Cosas Fernandes, Dana El Assad, Olivier De Castro, Nicolas D. Boscher

    Porous and highly conjugated multiply fused porphyrin thin films are prepared from a fast and single-step chemical vapor deposition approach. While the solution-based coupling of porphyrins is usually undertaken at room temperature, the gas phase reaction of nickel(II) 5,15-(diphenyl)porphyrin and iron(III) chloride (FeCl3) is investigated for temperatures as high as 200°C. Helium ion and atomic force microscopy, supported by weight and thickness measurements, shows a drastic decrease of the fused porphyrin thin film’s density accompanied by the formation of a mesoporous morphology upon increase of the reaction temperature. The increase of the film’s porosity is attributed to formation of a greater amount of HCl (originated from both the oxidative coupling and chlorination reactions) and the release of gaseous FeCl3 by-products, i.e. Cl2, at higher deposition temperatures. In addition, high resolution mass spectrometry reveals that increase of the reaction temperature promotes a higher degree of conjugation of the fused porphyrins chains, which ensures that high electronic conductivities are maintained along with high porosity. The method reported herein could enable the engineering of fused porphyrin thin films in sensing and catalytic devices.