Xiang Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiang Yu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Xiangdong Chen
Southwest Jiaotong University
10 shared publications - Xinpeng Chen
School of Network and Communication Engineering, Chengdu Technological University, Chengdu, Sichuan, China
7 shared publications - Xing Ding
School of Information Science and Technology, Southwest Jiaotong University, Chengdu, China
6 shared publications - Xing Ding
School of Information Science and Technology, Southwest Jiaotong University, Chengdu, China
4 shared publications - Xinglin Yu
School of Information Science and Technology, Southwest Jiaotong University, Chengdu, China
4 shared publications - Xuan Zhao
School of Information Science and Technology, Southwest Jiaotong University, Chengdu, China
4 shared publications
Latest Publications
- 25 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (11) , 11547-11553
Highly Sensitive QCM Humidity Sensor Based on Fullerenol-Assisted Dispersion of Nafion/MWCNTs Composites
Water seepage of building walls is a common problem in our lives. However, the lack of early seepage detection methods often makes the problem worse. To develop effective early wall seepage detection methods, an ultra-sensitive quartz crystal microbalance (QCM) humidity sensor based on fullerenol (C 60 -OH)-assisted dispersion of Nafion/multi-walled carbon nanotubes (MWCNTs) composites is proposed. The prepared sensor shows almost 7 times higher frequency shift than pure Nafion-based sensor, which reaches -10814 Hz. This is mainly attributed to the uniform dispersion of MWCNTs in the Nafion with the assistance of C 60 -OH to form a reticular structure that generates more voids, which greatly improves the diffusion ability of water molecules in the composite materials and thus further enhances humidity sensing properties of the sensor. The high-performance QCM humidity sensor is expected to be used for early detection of water seepage in building walls by monitoring air humidity changes near the wall surface.
- 25 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (11) , 11547-11553
Highly Sensitive QCM Humidity Sensor Based on Fullerenol-Assisted Dispersion of Nafion/MWCNTs Composites
Water seepage of building walls is a common problem in our lives. However, the lack of early seepage detection methods often makes the problem worse. To develop effective early wall seepage detection methods, an ultra-sensitive quartz crystal microbalance (QCM) humidity sensor based on fullerenol (C 60 -OH)-assisted dispersion of Nafion/multi-walled carbon nanotubes (MWCNTs) composites is proposed. The prepared sensor shows almost 7 times higher frequency shift than pure Nafion-based sensor, which reaches -10814 Hz. This is mainly attributed to the uniform dispersion of MWCNTs in the Nafion with the assistance of C 60 -OH to form a reticular structure that generates more voids, which greatly improves the diffusion ability of water molecules in the composite materials and thus further enhances humidity sensing properties of the sensor. The high-performance QCM humidity sensor is expected to be used for early detection of water seepage in building walls by monitoring air humidity changes near the wall surface.
- Open Access
- 6 July 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (7) , 264
Gas Sensitive Characteristics of Polyaniline Decorated with Molybdenum Ditelluride Nanosheets
In this work, hydrochloric acid (HCl)-doped molybdenum ditelluride (MoTe2) nanosheets/polyaniline (PANI) nanofiber composites are prepared by in situ chemical oxidation polymerization, and then the composites are deposited on interdigital electrodes (IDEs) to fabricate a NH3 gas sensor. Morphological analysis of the composites reveals that the PANI fibers are deposited on 2D MoTe2 sheets, showing a porous mesh microstructure structure with a more continuous distribution of PANI layer. FTIR spectrum analysis indicates the interaction between the MoTe2 nanosheets and the PANI in the MoTe2/PANI composites. The results demonstrate that the as-prepared MoTe2/PANI composites exhibit higher response than the pure PANI, in particular, the 8 wt.% MoTe2/PANI composites display about 4.23 times enhancement in response value toward 1000 ppm NH3 gas compared with the pure PANI. The enhanced NH3 gas-sensitive properties may be due to the increasing surface area of MoTe2/PANI composite films and the possible interaction of the P-N heterojunctions formed between PANI and the 2H-MoTe2 nanosheets.
- 6 July 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (7) , 264
Open AccessGas Sensitive Characteristics of Polyaniline Decorated with Molybdenum Ditelluride Nanosheets
In this work, hydrochloric acid (HCl)-doped molybdenum ditelluride (MoTe2) nanosheets/polyaniline (PANI) nanofiber composites are prepared by in situ chemical oxidation polymerization, and then the composites are deposited on interdigital electrodes (IDEs) to fabricate a NH3 gas sensor. Morphological analysis of the composites reveals that the PANI fibers are deposited on 2D MoTe2 sheets, showing a porous mesh microstructure structure with a more continuous distribution of PANI layer. FTIR spectrum analysis indicates the interaction between the MoTe2 nanosheets and the PANI in the MoTe2/PANI composites. The results demonstrate that the as-prepared MoTe2/PANI composites exhibit higher response than the pure PANI, in particular, the 8 wt.% MoTe2/PANI composites display about 4.23 times enhancement in response value toward 1000 ppm NH3 gas compared with the pure PANI. The enhanced NH3 gas-sensitive properties may be due to the increasing surface area of MoTe2/PANI composite films and the possible interaction of the P-N heterojunctions formed between PANI and the 2H-MoTe2 nanosheets.
- 13 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-10
A Modified Quartz Crystal Capacitance Circuit by Using Parallel Inductance and Its Application for Microdisplacement Sensing
In this article, we proposed a modified quartz crystal (QC) capacitance circuit with enhanced capacitance load performance constructed by using an inductor in parallel with the capacitor in a traditional QC capacitance circuit. The modified circuit was called as QCLC circuit for short. The QCLC circuit principle was studied by theoretical derivation and finite element simulation. Analytical expression for resonant frequency of the QCLC circuit is derived. Both theoretical calculation and finite element simulation results demonstrated that the QCLC circuit has a large capacitance (>50 pF) load capacity. Furthermore, the capacitance-frequency pulling sensitivity of the QCLC circuit can be adjusted by setting the parallel inductance value. Finally, the QCLC circuit was applied to construct a microdisplacement (MD) sensor with quasi-digital frequency output. A sensor prototype was fabricated by using a capacitive displacement detection element instead of the capacitor in the QCLC circuit. A sensitivity of 1.85 Hz/ $\mu \text{m}$ was obtained for a detecting distance of 0–1 mm. Sensing performances such as repeatability and stability were studied as well. The proposed QCLC circuit had the potential for developing capacitive sensors with quasi-digital frequency output.
- 13 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-10
A Modified Quartz Crystal Capacitance Circuit by Using Parallel Inductance and Its Application for Microdisplacement Sensing
In this article, we proposed a modified quartz crystal (QC) capacitance circuit with enhanced capacitance load performance constructed by using an inductor in parallel with the capacitor in a traditional QC capacitance circuit. The modified circuit was called as QCLC circuit for short. The QCLC circuit principle was studied by theoretical derivation and finite element simulation. Analytical expression for resonant frequency of the QCLC circuit is derived. Both theoretical calculation and finite element simulation results demonstrated that the QCLC circuit has a large capacitance (>50 pF) load capacity. Furthermore, the capacitance-frequency pulling sensitivity of the QCLC circuit can be adjusted by setting the parallel inductance value. Finally, the QCLC circuit was applied to construct a microdisplacement (MD) sensor with quasi-digital frequency output. A sensor prototype was fabricated by using a capacitive displacement detection element instead of the capacitor in the QCLC circuit. A sensitivity of 1.85 Hz/ $\mu \text{m}$ was obtained for a detecting distance of 0–1 mm. Sensing performances such as repeatability and stability were studied as well. The proposed QCLC circuit had the potential for developing capacitive sensors with quasi-digital frequency output.
- 1 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (3) , 1321-1326
Ultrahighly Sensitive QCM Humidity Sensor Based on Nafion/MoS2 Hybrid Thin Film
In this article, a Nafion/MoS 2 hybrid thin film was deposited on quartz crystal microbalance (QCM) for detecting humidity, in which moderate MoS 2 nanosheets with small size were dispersed into a Nafion membrane to improve its humidity sensitivity. The experimental results indicate that a hybrid film QCM humidity sensor with the best volume ratio of Nafion/MoS 2 exhibits a considerably higher shift frequency (−11 879 Hz) than a pure Nafion film QCM humidity sensor, even more than most of the reported QCM humidity sensors. It could be that the molybdenum disulfide nanosheets dispersed in the Nafion film would form some nano-assembly near the hydrophilic group of Nafion, which greatly enhances the ability of the composite film to establish water channels, thus promoting hydrophilicity of the composite film. The highly sensitive humidity sensor could clearly distinguish tiny humidity difference near the back and palm of a hand. Therefore, it has potential application in human–robot collaboration.
- 1 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (3) , 1321-1326
Ultrahighly Sensitive QCM Humidity Sensor Based on Nafion/MoS2 Hybrid Thin Film
In this article, a Nafion/MoS 2 hybrid thin film was deposited on quartz crystal microbalance (QCM) for detecting humidity, in which moderate MoS 2 nanosheets with small size were dispersed into a Nafion membrane to improve its humidity sensitivity. The experimental results indicate that a hybrid film QCM humidity sensor with the best volume ratio of Nafion/MoS 2 exhibits a considerably higher shift frequency (−11 879 Hz) than a pure Nafion film QCM humidity sensor, even more than most of the reported QCM humidity sensors. It could be that the molybdenum disulfide nanosheets dispersed in the Nafion film would form some nano-assembly near the hydrophilic group of Nafion, which greatly enhances the ability of the composite film to establish water channels, thus promoting hydrophilicity of the composite film. The highly sensitive humidity sensor could clearly distinguish tiny humidity difference near the back and palm of a hand. Therefore, it has potential application in human–robot collaboration.
- 6 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (3) , 1905-1915
Gas-Sensitive Enhancement of rGO/HMWCNTs/PANI Ternary Composites
This work reports a manufacturing method of NH3 gas sensor based on reduced graphene oxide/hydroxylated multi-walled carbon nanotu-bes/polyaniline (rGO/HMWCNTs/PANI) ternary composites. Firstly, rGO/HM-WCNT composites are fabricated from GO/HMWCNTs suspension via hydrot-hermal reduction method. Secondly, the rGO/HMWCNTs composites and aniline monomers are used to synthesize rGO/HMWCNTs/PANI ternary composites by in-situ chemical oxidative polymerization. The results indicate that the rGO/HMWCNTs/PANI ternary composites have significantly higher sensitive properties to NH3 gas compare to pure PANI and HMWCNTs/PANI binary composites. Its response to NH3 gas is respectively about 4.8 times that of pure PANI and 2.2 times that of HMWCNTs/PANI binary composites over the concentration range of 10-1000 ppm. The main reason may be that this method not only improves dispersion of HMWCNTs in PANI due to introduction of GO, but also maintains good charge transfer between HMWCNTs and PANI owing to hydrothermal reduction of GO to rGO, thus enhancing NH3 gas-sensitive properties of the ternary composites.
- 6 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 22 (3) , 1905-1915
Gas-Sensitive Enhancement of rGO/HMWCNTs/PANI Ternary Composites
This work reports a manufacturing method of NH3 gas sensor based on reduced graphene oxide/hydroxylated multi-walled carbon nanotu-bes/polyaniline (rGO/HMWCNTs/PANI) ternary composites. Firstly, rGO/HM-WCNT composites are fabricated from GO/HMWCNTs suspension via hydrot-hermal reduction method. Secondly, the rGO/HMWCNTs composites and aniline monomers are used to synthesize rGO/HMWCNTs/PANI ternary composites by in-situ chemical oxidative polymerization. The results indicate that the rGO/HMWCNTs/PANI ternary composites have significantly higher sensitive properties to NH3 gas compare to pure PANI and HMWCNTs/PANI binary composites. Its response to NH3 gas is respectively about 4.8 times that of pure PANI and 2.2 times that of HMWCNTs/PANI binary composites over the concentration range of 10-1000 ppm. The main reason may be that this method not only improves dispersion of HMWCNTs in PANI due to introduction of GO, but also maintains good charge transfer between HMWCNTs and PANI owing to hydrothermal reduction of GO to rGO, thus enhancing NH3 gas-sensitive properties of the ternary composites.
- 18 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (10) , 5149-5154
A Quartz Crystal Microbalance (QCM) Humidity Sensor Based on a Pencil-Drawn Method With High Quality Factor
In this work, we, for the first time, propose a quartz crystal microbalance (QCM) humidity sensor that is prepared by a one-step method based on pencil drawing. The scanning electron microscopy (SEM), atomic force microscope (AFM), and Raman spectra confirm some graphite flakes, and a layer of sensing film is formed, demonstrating the successful preparation of the QCM sensor. A series of experiments were performed by means of oscillating circuit and impedance analysis at room temperature. The impedance analysis method demonstrates that the QCM humidity sensor exhibits an excellent stability with a quality factor ( ${Q}$ ) that only drops from 47 923 to 43 849 in the whole humidity range, which is better than ever reported QCM humidity sensors. In addition, the sensor shows a good long-term stability with a maximal frequency deviation of less than 5% in a long-term test. Furthermore, the sensor displays a rapid response time ~8s and a recovery time less than 5 s. The underlying reasons for these excellent properties of the proposed sensor are analyzed and discussed. This research demonstrates that the pencil-drawn method is a simple, green, and cost-effective way for constructing a QCM humidity sensor with high performance.
- 18 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (10) , 5149-5154
A Quartz Crystal Microbalance (QCM) Humidity Sensor Based on a Pencil-Drawn Method With High Quality Factor
In this work, we, for the first time, propose a quartz crystal microbalance (QCM) humidity sensor that is prepared by a one-step method based on pencil drawing. The scanning electron microscopy (SEM), atomic force microscope (AFM), and Raman spectra confirm some graphite flakes, and a layer of sensing film is formed, demonstrating the successful preparation of the QCM sensor. A series of experiments were performed by means of oscillating circuit and impedance analysis at room temperature. The impedance analysis method demonstrates that the QCM humidity sensor exhibits an excellent stability with a quality factor ( ${Q}$ ) that only drops from 47 923 to 43 849 in the whole humidity range, which is better than ever reported QCM humidity sensors. In addition, the sensor shows a good long-term stability with a maximal frequency deviation of less than 5% in a long-term test. Furthermore, the sensor displays a rapid response time ~8s and a recovery time less than 5 s. The underlying reasons for these excellent properties of the proposed sensor are analyzed and discussed. This research demonstrates that the pencil-drawn method is a simple, green, and cost-effective way for constructing a QCM humidity sensor with high performance.
- 22 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (17) , 18477-18482
Humidity Sensing Properties and Negative Differential Resistance Effects of TiO2 Nanowires
This paper reports a humidity sensor based on TiO 2 nanowires. The humidity sensor prepared with a simple and easy technology exhibits obviously high sensitivity and fast response/recovery speed. A series of analyses including scanning electron microscopy, specific surface area analysis, water contact angle, and complex impedance spectrum were used to analyze superior humidity sensing performance of TiO 2 nanowires. The results demonstrate that higher sensitivity of the sensor probably stems from larger specific area of nanowires, and its faster response might be attributed to the continuity of nanowires and their intricate connection network, which offer highways for water molecules diffusion and charges transport. Besides, the current-voltage characteristic of the sensor presents a negative differential resistance effect (NDR) with a very low bias voltage under certain humidity level at room temperature, which facilitates compatibility with some low voltage integrated circuit. The tip enhancement of electric field caused by TiO 2 nanowire end is suggested to explain the mechanism of NDR at very low bias voltage. The high-performance humidity sensor provides a way to study the gender difference in moisture loss through skin evaporation with a non-contact manner, which can avoid the interference of contact state between the sensor and the skin.
- 22 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (17) , 18477-18482
Humidity Sensing Properties and Negative Differential Resistance Effects of TiO2 Nanowires
This paper reports a humidity sensor based on TiO 2 nanowires. The humidity sensor prepared with a simple and easy technology exhibits obviously high sensitivity and fast response/recovery speed. A series of analyses including scanning electron microscopy, specific surface area analysis, water contact angle, and complex impedance spectrum were used to analyze superior humidity sensing performance of TiO 2 nanowires. The results demonstrate that higher sensitivity of the sensor probably stems from larger specific area of nanowires, and its faster response might be attributed to the continuity of nanowires and their intricate connection network, which offer highways for water molecules diffusion and charges transport. Besides, the current-voltage characteristic of the sensor presents a negative differential resistance effect (NDR) with a very low bias voltage under certain humidity level at room temperature, which facilitates compatibility with some low voltage integrated circuit. The tip enhancement of electric field caused by TiO 2 nanowire end is suggested to explain the mechanism of NDR at very low bias voltage. The high-performance humidity sensor provides a way to study the gender difference in moisture loss through skin evaporation with a non-contact manner, which can avoid the interference of contact state between the sensor and the skin.
- 1 February 2021
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 329
Humidity Sensitivity Enhancement Effects of Metal Nanoparticles Loaded Fullerene
- 1 February 2021
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 329
Humidity Sensitivity Enhancement Effects of Metal Nanoparticles Loaded Fullerene
- 1 March 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 226, 378-386
Enhanced ammonia sensitive properties and mechanism research of PANI modified with hydroxylated single-walled nanotubes
- 1 March 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 226, 378-386
Enhanced ammonia sensitive properties and mechanism research of PANI modified with hydroxylated single-walled nanotubes