Elaheh Taghaddos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Elaheh Taghaddos has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Ahmad Safari
Department of Materials Science and Engineering, Rutgers University 1 , Piscataway, New Jersey 08854, USA
3 shared publicationsAhmed Safari
1 shared publication- Eric Garfunkel
Rutgers, The State University of New Jersey
1 shared publication Gerard Charles Dismukes
Rutgers University
1 shared publicationGraeme Gardner
Rutgers University
1 shared publicationHarry Charalambous
Argonne National Laboratory 2 , 9700 S Cass Ave., Lemont, Illinois 60439, USA
1 shared publication
Latest Publications
- 11 August 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (6) , 064103
Acceptor dopant mediated electrical property modification in Bi0.5Na0.5TiO3-based piezoceramic
The effect of Mn and Fe dopants on the electromechanical and electrochemical properties of 0.88[Bi0.5Na0.5]TiO3–0.08[Bi0.5K0.5]TiO3–0.04[Bi0.5Li0.5]TiO3 piezoceramic is investigated with particular emphasis on complex impedance in the temperature range from 450 to 600 °C. The impedance spectra have been simulated with equivalent circuits in order to extract bulk and grain boundary characteristics and to determine activation energies of conduction. Mn and Fe dopants considerably enhance the mechanical quality factor and decrease the dielectric loss compared to the undoped composition. Mn doping leads to dramatically higher resistivity in the bulk and a modest increase in the bulk activation energy. On the other hand, conductivity increases dramatically via Fe doping with a significant lowering of activation energy in the bulk and corresponding raising of the activation energy at grain boundaries in comparison to Mn-doped and undoped ceramic. The bulk conductivity of Fe-doped piezoceramic reaches as high as 0.01 S cm−1 at 600 °C.
- 11 August 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (6) , 064103
Acceptor dopant mediated electrical property modification in Bi0.5Na0.5TiO3-based piezoceramic
The effect of Mn and Fe dopants on the electromechanical and electrochemical properties of 0.88[Bi0.5Na0.5]TiO3–0.08[Bi0.5K0.5]TiO3–0.04[Bi0.5Li0.5]TiO3 piezoceramic is investigated with particular emphasis on complex impedance in the temperature range from 450 to 600 °C. The impedance spectra have been simulated with equivalent circuits in order to extract bulk and grain boundary characteristics and to determine activation energies of conduction. Mn and Fe dopants considerably enhance the mechanical quality factor and decrease the dielectric loss compared to the undoped composition. Mn doping leads to dramatically higher resistivity in the bulk and a modest increase in the bulk activation energy. On the other hand, conductivity increases dramatically via Fe doping with a significant lowering of activation energy in the bulk and corresponding raising of the activation energy at grain boundaries in comparison to Mn-doped and undoped ceramic. The bulk conductivity of Fe-doped piezoceramic reaches as high as 0.01 S cm−1 at 600 °C.
- 1 August 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (9) , 2882-2888
Electromechanical properties of flash sintered BNT-based piezoelectric ceramic
- 1 August 2019
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 39 (9) , 2882-2888
Electromechanical properties of flash sintered BNT-based piezoelectric ceramic
- Open Access
- 15 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 65 (4) , 582-588
Fabrication and Characterization of Single-Aperture 3.5-MHz BNT-Based Ultrasonic Transducer for Therapeutic Application
This paper discusses the fabrication and characterization of 3.5-MHz single-element transducers for therapeutic applications in which the active elements are made of hard lead-free BNT-based and hard commercial PZT (PZT-841) piezoceramics. Composition of (BiNa 0.88 K 0.08 Li 0.04 ) 0.5 (Ti 0.985 Mn 0.015 )O 3 (BNKLT88-1.5Mn) was used to develop lead-free piezoelectric ceramic. Mn-doped samples exhibited high mechanical quality factor (Q m ) of 970, thickness coupling coefficient (k t ) of 0.48, a dielectric constant (ε 33 T ) of 310 (at 1 kHz), depolarization temperature (T d ) of 200 °C, and coercive field (E c ) of 52.5 kV/cm. Two different unfocused single-element transducers using BNKLT88-1.5Mn and PZT-841 with the same center frequency of 3.5 MHz and similar aperture size of 10.7 and 10.5 mm were fabricated. Pulse-echo response, acoustic frequency spectrum, acoustic pressure field, and acoustic intensity field of transducers were characterized. The BNT-based transducer shows linear response up to the peak-to-peak voltage of 105 V in which the maximum rarefactional acoustic pressure of 1.1 MPa, and acoustic intensity of 43 W/cm 2 were achieved. Natural focal point of this transducer was at 60 mm from the surface of the transducer.
- 15 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 65 (4) , 582-588
Open AccessFabrication and Characterization of Single-Aperture 3.5-MHz BNT-Based Ultrasonic Transducer for Therapeutic Application
This paper discusses the fabrication and characterization of 3.5-MHz single-element transducers for therapeutic applications in which the active elements are made of hard lead-free BNT-based and hard commercial PZT (PZT-841) piezoceramics. Composition of (BiNa 0.88 K 0.08 Li 0.04 ) 0.5 (Ti 0.985 Mn 0.015 )O 3 (BNKLT88-1.5Mn) was used to develop lead-free piezoelectric ceramic. Mn-doped samples exhibited high mechanical quality factor (Q m ) of 970, thickness coupling coefficient (k t ) of 0.48, a dielectric constant (ε 33 T ) of 310 (at 1 kHz), depolarization temperature (T d ) of 200 °C, and coercive field (E c ) of 52.5 kV/cm. Two different unfocused single-element transducers using BNKLT88-1.5Mn and PZT-841 with the same center frequency of 3.5 MHz and similar aperture size of 10.7 and 10.5 mm were fabricated. Pulse-echo response, acoustic frequency spectrum, acoustic pressure field, and acoustic intensity field of transducers were characterized. The BNT-based transducer shows linear response up to the peak-to-peak voltage of 105 V in which the maximum rarefactional acoustic pressure of 1.1 MPa, and acoustic intensity of 43 W/cm 2 were achieved. Natural focal point of this transducer was at 60 mm from the surface of the transducer.
- 1 August 2016
- Published by The Electrochemical Society in ECS Transactions
- Vol. 72 (37) , 1-19
Optimizing “Artificial Leaf” Photoanode-Photocathode-Catalyst Interface Systems for Solar Water Splitting
A novel dual photoabsorber interface: perovskite oxynitride (SrNbO2N) deposited on silicon (100), and a H2ER catalyst photoabsorber interface: (Ni5P4 or Ni2P)-silicon, are fabricated. Titanium nitride (TiN) is introduced as a blocking layer between Sr2Nb2O7 and Si (100), which produces clean interfaces. During the high temperature ammonolysis step needed to convert Sr2Nb2O7 to SrNbO2N, it is effective at blocking Nb and Si (but not Sr) migration. A half-cell cathode with the H2ER catalyst (Ni5P4 or Ni2P)-photoabsorber interface produces H2 approaching best-in-class overpotentials for films (Ni5P4: 211mV vs RHE at 10mV/cm2) with a 50mV/decade Tafel slope. Films are atomically smooth, except for surface phosphate that is removed during electrolysis.
- 1 August 2016
- Published by The Electrochemical Society in ECS Transactions
- Vol. 72 (37) , 1-19
Optimizing “Artificial Leaf” Photoanode-Photocathode-Catalyst Interface Systems for Solar Water Splitting
A novel dual photoabsorber interface: perovskite oxynitride (SrNbO2N) deposited on silicon (100), and a H2ER catalyst photoabsorber interface: (Ni5P4 or Ni2P)-silicon, are fabricated. Titanium nitride (TiN) is introduced as a blocking layer between Sr2Nb2O7 and Si (100), which produces clean interfaces. During the high temperature ammonolysis step needed to convert Sr2Nb2O7 to SrNbO2N, it is effective at blocking Nb and Si (but not Sr) migration. A half-cell cathode with the H2ER catalyst (Ni5P4 or Ni2P)-photoabsorber interface produces H2 approaching best-in-class overpotentials for films (Ni5P4: 211mV vs RHE at 10mV/cm2) with a 50mV/decade Tafel slope. Films are atomically smooth, except for surface phosphate that is removed during electrolysis.