Yung-Chuan Chiou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yung-Chuan Chiou has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Chia-Chin Wu
Department of Mechanical and Energy Engineering, National Chiayi University, Chiayi 60004, Taiwan
2 shared publications - Ming-Yuan Shen
National Chung Hsing University
2 shared publications - Chung-Ming Tan
Department of Mechanical Engineering, WuFeng University, Chiayi 62153, Taiwan
1 shared publication Hsin-Yin Chou
1 shared publicationLiang-Hsiung Chou
1 shared publicationMing‐Chuen Yip
Department of Power Mechanical Engineering , National Tsing‐Hua University , Hsinchu 300, Taiwan
1 shared publication
Latest Publications
- Open Access
Effect of Wall Thickness on Stress–Strain Response and Buckling Behavior of Hollow-Cylinder Rubber Fenders
In this study, the effect of wall thickness (15–25 mm) on the stress–strain response of hollow-cylinder rubber fenders were investigated by conducting monotonic compression tests. It was found that a progressive increase in lateral bending deformation was observed during monotonic compression. Simultaneously, the extent of the lateral deflection decreased notably with an increasing wall thickness. From the experimental results, the fact is accepted that buckling occurred in the tested fender due to the fact that the ratio of the height to the wall thickness was higher than four in all of the considered cases. Moreover, an s-shape profile appeared in the stress–strain curves, which became clearer as the wall thickness was reduced from 25 to 15 mm. To assess the performance of fenders objectively, an energy-effectiveness index, , was introduced to quantify the energy absorption capacity of the fender. From the experimental observations, it was inferred that the contact area of the folded inner surface of the fender produced under compression generated an additional reaction force and affected the shape of the stress–strain curve since the measured load consisted of two reaction forces: one caused by the self-contact area, and the other resulted from the compression-bending deformation that occurred in the side wall of the fender. To examine this assertion, a finite element analysis (FEA) was conducted and confirmed the effect of the reaction force on the sensitivity of the s-shape characteristic of the stress–strain curve. Finally, a polynomial regression was conducted and the calculated results based on the fourth-degree stress polynomial function correlated very well with the measured stress–strain curves.Open AccessEffect of Wall Thickness on Stress–Strain Response and Buckling Behavior of Hollow-Cylinder Rubber Fenders
In this study, the effect of wall thickness (15–25 mm) on the stress–strain response of hollow-cylinder rubber fenders were investigated by conducting monotonic compression tests. It was found that a progressive increase in lateral bending deformation was observed during monotonic compression. Simultaneously, the extent of the lateral deflection decreased notably with an increasing wall thickness. From the experimental results, the fact is accepted that buckling occurred in the tested fender due to the fact that the ratio of the height to the wall thickness was higher than four in all of the considered cases. Moreover, an s-shape profile appeared in the stress–strain curves, which became clearer as the wall thickness was reduced from 25 to 15 mm. To assess the performance of fenders objectively, an energy-effectiveness index, , was introduced to quantify the energy absorption capacity of the fender. From the experimental observations, it was inferred that the contact area of the folded inner surface of the fender produced under compression generated an additional reaction force and affected the shape of the stress–strain curve since the measured load consisted of two reaction forces: one caused by the self-contact area, and the other resulted from the compression-bending deformation that occurred in the side wall of the fender. To examine this assertion, a finite element analysis (FEA) was conducted and confirmed the effect of the reaction force on the sensitivity of the s-shape characteristic of the stress–strain curve. Finally, a polynomial regression was conducted and the calculated results based on the fourth-degree stress polynomial function correlated very well with the measured stress–strain curves. - Open Access
- 1 September 2019
- Published by Elsevier in Materials & Design
- Vol. 178
Effects of adding graphene nanoplatelets and nanocarbon aerogels to epoxy resins and their carbon fiber composites
- 1 September 2019
- Published by Elsevier in Materials & Design
- Vol. 178
Open AccessEffects of adding graphene nanoplatelets and nanocarbon aerogels to epoxy resins and their carbon fiber composites
- 1 March 2019
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 100, 185-194
A GE/BC imbedded local polynomial collocation method for two dimensional multivariable problems
- 1 March 2019
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 100, 185-194
A GE/BC imbedded local polynomial collocation method for two dimensional multivariable problems
- Open Access
Stress-Strain Response of Cylindrical Rubber Fender under Monotonic and Cyclic Compression
The study was devoted to the observation and modeling the mechanical behaviors of a hybrid SBR/NR (Styrene-Butadiene/Natural Rubber) hybrid vulcanized rubber fender under monotonic/cyclic compression. In experimental observations of the monotonic compression tests, it was found that lateral deformation occurred on the tested fender and was more significant with increasing the extent of the compressive strain. The relationship between the transmission stress and the compressive strain was nonlinear and the absorbed strain-energy-density was increased monotonically with the increment of the compressive strain. Among all cyclic compression tests with strain controlled, the reductions in both the stress range and the absorbed strain-energy-density up to the ten-thousandth cycle were found and then both of the cyclic properties remain approximately constant in the following compression cycles. Two new properties, the softening factor and the energy reduction factor, were introduced to quantify the effect of the strain range on the extent of the reduction in stress range and that on the absorbed strain-energy-density, respectively. It was found that both of the calculated values of the new properties increase with the increment of strain range. In mathematical modeling of the relationship between the transmission stress and the compressive strain, a new approach based on energy-polynomial-function was presented and was successfully used to simulate the monotonic curve and the stable hysteresis loop curves of the tested rubber fender in compression. Essentially, the energy-polynomial-function was obtained by performing a polynomial regression on a large amount of ( data. Moreover, the least-square approach was applied to determine the corresponding regression coefficients in . Clearly, the stress-polynomial-function in modeling the curve could be obtained from the differentiation of the energy-polynomial-function with respect to the compressive strain. In addition, to provide an adequate estimation of the mechanical properties of the cylindrical rubber fender under compression, the named cyclic stress-strain curve and cyclic energy-strain curve were developed and also modeled in this study.Open AccessStress-Strain Response of Cylindrical Rubber Fender under Monotonic and Cyclic Compression
The study was devoted to the observation and modeling the mechanical behaviors of a hybrid SBR/NR (Styrene-Butadiene/Natural Rubber) hybrid vulcanized rubber fender under monotonic/cyclic compression. In experimental observations of the monotonic compression tests, it was found that lateral deformation occurred on the tested fender and was more significant with increasing the extent of the compressive strain. The relationship between the transmission stress and the compressive strain was nonlinear and the absorbed strain-energy-density was increased monotonically with the increment of the compressive strain. Among all cyclic compression tests with strain controlled, the reductions in both the stress range and the absorbed strain-energy-density up to the ten-thousandth cycle were found and then both of the cyclic properties remain approximately constant in the following compression cycles. Two new properties, the softening factor and the energy reduction factor, were introduced to quantify the effect of the strain range on the extent of the reduction in stress range and that on the absorbed strain-energy-density, respectively. It was found that both of the calculated values of the new properties increase with the increment of strain range. In mathematical modeling of the relationship between the transmission stress and the compressive strain, a new approach based on energy-polynomial-function was presented and was successfully used to simulate the monotonic curve and the stable hysteresis loop curves of the tested rubber fender in compression. Essentially, the energy-polynomial-function was obtained by performing a polynomial regression on a large amount of ( data. Moreover, the least-square approach was applied to determine the corresponding regression coefficients in . Clearly, the stress-polynomial-function in modeling the curve could be obtained from the differentiation of the energy-polynomial-function with respect to the compressive strain. In addition, to provide an adequate estimation of the mechanical properties of the cylindrical rubber fender under compression, the named cyclic stress-strain curve and cyclic energy-strain curve were developed and also modeled in this study. - 1 June 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 636, 320-325
The effects of pre-cycle damage on subsequent material behavior and fatigue resistance of SUS 304 stainless steel
- 1 June 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 636, 320-325
The effects of pre-cycle damage on subsequent material behavior and fatigue resistance of SUS 304 stainless steel
- 10 December 2012
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 37 (1) , 26-35
Estimations of mechanical properties and fatigue life in pre-strained conditions
In this paper, the effects of tensile pre-deformation on material properties and fatigue life are investigated. For this purpose, a series of tensile fracture tests and fully reversed cyclic mode load-controlled tests have been performed on the tested 430 Stainless Steel in as-received condition and for the same tested material pre-strained at room temperature. Tensile pre-strain, , conditions were induced at three levels: 5%, 8%, and 12%. Experimental observations on tensile properties, fatigue strength coefficient, and exponent were done and are represented in this study. Empirical formulas were developed in polynomial form to estimate the tensile properties in pre-strained condition. Meanwhile, in this study, two empirical relationships for estimating fatigue strength coefficient and exponent using ultimate strength have been proposed and the corresponding approximation of S–N curves based on the Basquin equation form have been developed. The approximation of the S–N curve has provided good predictions with most predicted lives within the factor 4 bound, but 73% of the predicted lives were still within the factor 2 bound. In consideration of the pre-strain effect on material behavior, a modified energy parameter was chosen and provided a more accurate prediction of reversals to failure for all pre-strained samples.
- 10 December 2012
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 37 (1) , 26-35
Estimations of mechanical properties and fatigue life in pre-strained conditions
In this paper, the effects of tensile pre-deformation on material properties and fatigue life are investigated. For this purpose, a series of tensile fracture tests and fully reversed cyclic mode load-controlled tests have been performed on the tested 430 Stainless Steel in as-received condition and for the same tested material pre-strained at room temperature. Tensile pre-strain, , conditions were induced at three levels: 5%, 8%, and 12%. Experimental observations on tensile properties, fatigue strength coefficient, and exponent were done and are represented in this study. Empirical formulas were developed in polynomial form to estimate the tensile properties in pre-strained condition. Meanwhile, in this study, two empirical relationships for estimating fatigue strength coefficient and exponent using ultimate strength have been proposed and the corresponding approximation of S–N curves based on the Basquin equation form have been developed. The approximation of the S–N curve has provided good predictions with most predicted lives within the factor 4 bound, but 73% of the predicted lives were still within the factor 2 bound. In consideration of the pre-strain effect on material behavior, a modified energy parameter was chosen and provided a more accurate prediction of reversals to failure for all pre-strained samples.
- 1 April 2006
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 29 (3) , 507-517
An energy‐based damage parameter for the life prediction of AISI 304 stainless steel subjected to mean strain
This study extends the plastic strain energy approach to predict the fatigue life of AISI 304 stainless steel. A modified energy parameter based on the stable plastic strain energy density under tension conditions is proposed to account for the mean strain and stress effects in a low cycle fatigue regime. The fatigue life curve based on the proposed energy parameter can be obtained directly by modifying the parameters in the fatigue life curve based on the stable plastic strain energy pertaining to fully reversed cyclic loading. Hence, the proposed damage parameter provides a convenient means of evaluating fatigue life on the mean strain or stress effect. The modified energy parameter can also be used to explain the combined effect of alternating and mean strain/stress on the fatigue life. In this study, the mean strain effects on the fatigue life of AISI 304 stainless steel are examined by performing fatigue tests at different mean strain levels. The experimental results indicate that the combination of an alternating strain and a mean strain strongly influences the fatigue life. Meanwhile, it is found that the change in fatigue life is sensitive to changes in the proposed damage parameter under the condition of a constant strain amplitude at various mean strain levels. A good agreement is observed between the experimental fatigue life and the fatigue life predicted by the proposed damage parameter. The damage parameter proposed by Smith et al. (1970) is also employed to quantify the mean strain effect. The results indicate that this parameter also provides a reasonable estimate of the fatigue life of AISI 304 stainless steel. However, a simple statistical analysis confirms that the proposed damage parameter provides a better prediction of the fatigue life of AISI 304 stainless steel than the SWT parameter.
- 1 April 2006
- Published by Taylor & Francis in Journal of the Chinese Institute of Engineers
- Vol. 29 (3) , 507-517
An energy‐based damage parameter for the life prediction of AISI 304 stainless steel subjected to mean strain
This study extends the plastic strain energy approach to predict the fatigue life of AISI 304 stainless steel. A modified energy parameter based on the stable plastic strain energy density under tension conditions is proposed to account for the mean strain and stress effects in a low cycle fatigue regime. The fatigue life curve based on the proposed energy parameter can be obtained directly by modifying the parameters in the fatigue life curve based on the stable plastic strain energy pertaining to fully reversed cyclic loading. Hence, the proposed damage parameter provides a convenient means of evaluating fatigue life on the mean strain or stress effect. The modified energy parameter can also be used to explain the combined effect of alternating and mean strain/stress on the fatigue life. In this study, the mean strain effects on the fatigue life of AISI 304 stainless steel are examined by performing fatigue tests at different mean strain levels. The experimental results indicate that the combination of an alternating strain and a mean strain strongly influences the fatigue life. Meanwhile, it is found that the change in fatigue life is sensitive to changes in the proposed damage parameter under the condition of a constant strain amplitude at various mean strain levels. A good agreement is observed between the experimental fatigue life and the fatigue life predicted by the proposed damage parameter. The damage parameter proposed by Smith et al. (1970) is also employed to quantify the mean strain effect. The results indicate that this parameter also provides a reasonable estimate of the fatigue life of AISI 304 stainless steel. However, a simple statistical analysis confirms that the proposed damage parameter provides a better prediction of the fatigue life of AISI 304 stainless steel than the SWT parameter.