Amanda Martins Nacas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Amanda Martins Nacas has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Demetrio Jackson dos Santos
Center of Engineering, Modeling and Applied Social Sciences, Federal University of ABC (UFABC), Santo Andre 09210-580, Brazil
5 shared publications - Anne Cristine Chinellato
Center of Engineering, Modelling and Applied Social Sciences, Federal University of ABC, Santo André, Brazil
3 shared publications - Lara Basílio Tavares
Nanoscience and Advanced Materials Graduate Program (PPG-Nano), Federal University of ABC (UFABC), Santo André 09210-580, Brazil
2 shared publications - Rogerio Ramos de Sousa Junior
Center of Engineering, Modeling and Applied Social Sciences, Federal University of ABC (UFABC), Santo Andre 09210-580, Brazil
2 shared publications - Cristiane R. Stilhano Vilas Boas
Industrial Focus Group XUV Optics, MESA+ Institute for Nanotechnology, University of Twente , Enschede, The Netherlands
1 shared publication D. S. Rosa
1 shared publication
Latest Publications
- 1 September 2019
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 93, 102326-58
Nano boron nitride/polyurethane adhesives in flexible laminated food packaging: Peeling resistance and permeability properties
- 1 September 2019
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 93, 102326-58
Nano boron nitride/polyurethane adhesives in flexible laminated food packaging: Peeling resistance and permeability properties
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 24 (3)
Lithium catalyst concentration influence on bio-polyols structure and polyurethane adhesives properties
Polyol structure can be affected by the catalyst used for its synthesis and may affect the curing kinetics and mechanical strength of the final polyurethane (PU). This work aimed to study the influence of catalyst concentration on the structure of bio-based polyols and on the final properties of the polyurethane adhesive obtained from these polyols. Polyols were investigated by Fourier transform infrared (FTIR), gel permeation chromatography (GPC) and hydroxyl index analysis, with the purpose of investigating the polyols chemical state after the synthesis. Results suggest that higher catalyst concentration led to polyols with higher hydroxyl index and other differences in the polyols structure. The influence of the catalysts concentration on the cure kinetics of the polyurethanes was verified using the Fourier transform infrared (FTIR). In addition, peel strength of PU adhesives was obtained by increasing catalyst concentration on polyol synthesis.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 24 (3)
Open AccessLithium catalyst concentration influence on bio-polyols structure and polyurethane adhesives properties
Polyol structure can be affected by the catalyst used for its synthesis and may affect the curing kinetics and mechanical strength of the final polyurethane (PU). This work aimed to study the influence of catalyst concentration on the structure of bio-based polyols and on the final properties of the polyurethane adhesive obtained from these polyols. Polyols were investigated by Fourier transform infrared (FTIR), gel permeation chromatography (GPC) and hydroxyl index analysis, with the purpose of investigating the polyols chemical state after the synthesis. Results suggest that higher catalyst concentration led to polyols with higher hydroxyl index and other differences in the polyols structure. The influence of the catalysts concentration on the cure kinetics of the polyurethanes was verified using the Fourier transform infrared (FTIR). In addition, peel strength of PU adhesives was obtained by increasing catalyst concentration on polyol synthesis.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (2)
Improvement of Polypropylene Adhesion by Kraft Lignin Incorporation
Low surface energy and poor adhesion are well-known characteristics of polypropylene (PP). Surface treatments such as plasma, corona, and laser are usually applied to overcome these limitations. However, current studies highlight the incorporation of hydrophilic or amphiphilic polymers into hydrophobic low-surface-energy polymers as an alternative for increasing surface energy and thus improving adhesion. Lignin could be a promising amphiphilic polymer for use in increasing surface energy. In this work, PP/kraft lignin composites were obtained by incorporating up to 5 wt% of kraft lignin (KL) into a PP matrix. Corona treatment was applied to pristine PP and composites surfaces. Contact angle measurements and peeling tests were carried out to investigate the effects of KL incorporation and corona treatment on the surface energy and the mechanical strength of adhesion. Differential scanning calorimetry (DSC) was used to evaluate the PP’s crystallinity index and recrystallization temperature and to dismiss their effects on the surface energy changes. Scanning electron microscopy (SEM) was applied to investigate the lignin dispersion. The results show that KL incorporation has potential as a method to improve the surface energy of PP, improve its poor adhesion, and enhance the effects of corona treatment.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (2)
Open AccessImprovement of Polypropylene Adhesion by Kraft Lignin Incorporation
Low surface energy and poor adhesion are well-known characteristics of polypropylene (PP). Surface treatments such as plasma, corona, and laser are usually applied to overcome these limitations. However, current studies highlight the incorporation of hydrophilic or amphiphilic polymers into hydrophobic low-surface-energy polymers as an alternative for increasing surface energy and thus improving adhesion. Lignin could be a promising amphiphilic polymer for use in increasing surface energy. In this work, PP/kraft lignin composites were obtained by incorporating up to 5 wt% of kraft lignin (KL) into a PP matrix. Corona treatment was applied to pristine PP and composites surfaces. Contact angle measurements and peeling tests were carried out to investigate the effects of KL incorporation and corona treatment on the surface energy and the mechanical strength of adhesion. Differential scanning calorimetry (DSC) was used to evaluate the PP’s crystallinity index and recrystallization temperature and to dismiss their effects on the surface energy changes. Scanning electron microscopy (SEM) was applied to investigate the lignin dispersion. The results show that KL incorporation has potential as a method to improve the surface energy of PP, improve its poor adhesion, and enhance the effects of corona treatment.
- 29 January 2018
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 94 (11) , 880-892
The role of polyol reaction catalysts in the cure kinetics and mechanical behavior of polyurethane adhesives
Polyurethane is one of the most versatile and commonly applied polymers in the world. Its properties are strongly dependent on the polyol/isocyanate structures and NCO:OH ratio, among other parameters. Additionally, the polyol structure is affected by the catalyst used for the reaction and production. The catalyst may indirectly affect the curing kinetics and mechanical strength of the PU, due to changes of polyol properties. This work evaluates the effects of two catalysts on the polyol structure and thus the effect of these polyol changes on the curing kinetics and mechanical strength of a PU adhesive. Two polyols were synthetized using the same hydroxyl-containing molecules derived from renewable natural sources, but with different types of catalysts (based on Sn or Li/Ti). The synthesized polyols were separately mixed with diphenylmethane diisocyanate in a 1.1:1 ratio of NCO to OH to form two bio-based PUs. The polyols were investigated by Fourier transform infrared (FTIR) spectroscopy, which showed the occurrence of some changes in the chemical groups of the polyol structure for both catalysts, as well as an influence on the curing kinetics. The mechanical behavior of the PU adhesives was characterized by dynamic mechanical analysis (DMA) and peeling tests. The results show a higher curing rate and higher peeling strength for the PU adhesives obtained using the Sn-based catalyst; both adhesives showed cohesive failure.
- 29 January 2018
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 94 (11) , 880-892
The role of polyol reaction catalysts in the cure kinetics and mechanical behavior of polyurethane adhesives
Polyurethane is one of the most versatile and commonly applied polymers in the world. Its properties are strongly dependent on the polyol/isocyanate structures and NCO:OH ratio, among other parameters. Additionally, the polyol structure is affected by the catalyst used for the reaction and production. The catalyst may indirectly affect the curing kinetics and mechanical strength of the PU, due to changes of polyol properties. This work evaluates the effects of two catalysts on the polyol structure and thus the effect of these polyol changes on the curing kinetics and mechanical strength of a PU adhesive. Two polyols were synthetized using the same hydroxyl-containing molecules derived from renewable natural sources, but with different types of catalysts (based on Sn or Li/Ti). The synthesized polyols were separately mixed with diphenylmethane diisocyanate in a 1.1:1 ratio of NCO to OH to form two bio-based PUs. The polyols were investigated by Fourier transform infrared (FTIR) spectroscopy, which showed the occurrence of some changes in the chemical groups of the polyol structure for both catalysts, as well as an influence on the curing kinetics. The mechanical behavior of the PU adhesives was characterized by dynamic mechanical analysis (DMA) and peeling tests. The results show a higher curing rate and higher peeling strength for the PU adhesives obtained using the Sn-based catalyst; both adhesives showed cohesive failure.
- 2 March 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (25)
Polypropylene composite reinforced with fibrillated curaua fiber and using maleic anhydride as coupling agent
Curaua fibers (CF) were fibrillated using high‐intensity ultrasonication, which is fast and uses water as a solvent. The fibrillated fibers (CFf) were used as reinforcement (20 wt %) in polypropylene composites processed by extrusion with or without 2 wt % of polypropylene grafted with maleic anhydride (PPMA). Fibrillation promotes an increase from 11.3 to 33.8 in the aspect ratio of the fiber. Sonication caused extraction of lignin and a decrease in the degree of crystallinity of the CF. Extrusion of the composites causes no additional fibrillation of the CF. A composite reinforced with CFf had tensile and flexural strength of 24.9% and 51.5%, respectively, higher than that of pristine PP. The use of PPMA and CFf in the composite promotes a further increase of 30% and 50.5% in these parameters, respectively. A thermal analysis of the composites using CFf with or without PPMA showed similar behavior. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44913.
- 2 March 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (25)
Polypropylene composite reinforced with fibrillated curaua fiber and using maleic anhydride as coupling agent
Curaua fibers (CF) were fibrillated using high‐intensity ultrasonication, which is fast and uses water as a solvent. The fibrillated fibers (CFf) were used as reinforcement (20 wt %) in polypropylene composites processed by extrusion with or without 2 wt % of polypropylene grafted with maleic anhydride (PPMA). Fibrillation promotes an increase from 11.3 to 33.8 in the aspect ratio of the fiber. Sonication caused extraction of lignin and a decrease in the degree of crystallinity of the CF. Extrusion of the composites causes no additional fibrillation of the CF. A composite reinforced with CFf had tensile and flexural strength of 24.9% and 51.5%, respectively, higher than that of pristine PP. The use of PPMA and CFf in the composite promotes a further increase of 30% and 50.5% in these parameters, respectively. A thermal analysis of the composites using CFf with or without PPMA showed similar behavior. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44913.
- 26 April 2016
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 93 (1-2) , 18-29
Effects of NCO:OH ratio on the mechanical properties and chemical structure of Kraft lignin–based polyurethane adhesive
This work aimed to evaluate the influence of the aliphatic and aromatic hydroxyl level on the polyurethane adhesive property and chemical structure. This adhesive was obtained through the reaction of technical Kraft lignin (TKL) as polyol with diphenylmethane diisocyanate (MDI). Thus, lignopolyurethane adhesives were obtained with NCO:OH ratios of 0.8:1.0, 0.9:1.0, 1.0:1.0, 1.1:1.0, and 1.2:1.0. Initially only the TKL aliphatic hydroxyl level was taken into consideration in the stoichiometry in order to define the mass ratio between MDI and polyol. Subsequently, lignopolyurethane adhesive was obtained using the same NCO:OH ratios considering TKL total hydroxyls’ level, and aromatic and aliphatic hydroxyls. The chemical structures of the synthesized adhesives were analyzed by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (13C NMR). The mechanical property of the adhesively bonded joints, comprising wood substrates and synthesized adhesives, was measured using single lap shear tests. Results illustrated that by increasing the NCO:OH ratio, there is an increase in the free isocyanate content leading to higher shear strength values. Higher free isocyanate content leads to MDI dimer formation in the lignopolyurethane structure.
- 26 April 2016
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 93 (1-2) , 18-29
Effects of NCO:OH ratio on the mechanical properties and chemical structure of Kraft lignin–based polyurethane adhesive
This work aimed to evaluate the influence of the aliphatic and aromatic hydroxyl level on the polyurethane adhesive property and chemical structure. This adhesive was obtained through the reaction of technical Kraft lignin (TKL) as polyol with diphenylmethane diisocyanate (MDI). Thus, lignopolyurethane adhesives were obtained with NCO:OH ratios of 0.8:1.0, 0.9:1.0, 1.0:1.0, 1.1:1.0, and 1.2:1.0. Initially only the TKL aliphatic hydroxyl level was taken into consideration in the stoichiometry in order to define the mass ratio between MDI and polyol. Subsequently, lignopolyurethane adhesive was obtained using the same NCO:OH ratios considering TKL total hydroxyls’ level, and aromatic and aliphatic hydroxyls. The chemical structures of the synthesized adhesives were analyzed by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (13C NMR). The mechanical property of the adhesively bonded joints, comprising wood substrates and synthesized adhesives, was measured using single lap shear tests. Results illustrated that by increasing the NCO:OH ratio, there is an increase in the free isocyanate content leading to higher shear strength values. Higher free isocyanate content leads to MDI dimer formation in the lignopolyurethane structure.
- 18 April 2016
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 93 (1-2) , 4-17
Study of the correlation between flexible food packaging peeling resistance and surface composition for aluminum-metallized BOPP films aged at 60°C
This study investigated the correlation between surface composition and peeling resistance in food packaging films by studying the heat aging of fabricated films over varying periods of time. The films consisted of a layer of aluminum (Al) metallized, biaxially oriented polypropylene (BOPP) bonded with a polyurethane (PU) adhesive onto another polymeric layer of low-density polyethylene (LDPE). The Al metallized films were prepared by physical vapor deposition (PVD) and aged at 60°C for either 5 or 15 days. The resulting aluminum surfaces were analyzed using X-ray photoelectron spectroscopy (XPS) and found to contain aluminum oxide (Al2O3) and trihydroxide (Al(OH)3). The XPS characterization also revealed a 29% increase in the Al(OH)3 layer thickness of the aged sample relative to a non-aged sample. Atomic force microscopy (AFM) was applied on investigations of possible morphology changes. The aluminum and PU adhesive surface energies were also determined using contact angles measurements and the aluminum surface energy was found to increase by as much as 11.7% compared to the non-aged sample, while the PU adhesive surface energy was at least 65% higher than that of the metallic substrate. The peeling resistance of the laminated aluminum was determined by average peel strength measurements and it was found that the variation in peel strength was related to changes in the Al2O3 layer thickness. The delaminated samples were analyzed using scanning electron microscopy/energy dispersive X-ray spectrometry (SEM/EDS) and showed the cohesive failure of the aluminum film.
- 18 April 2016
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 93 (1-2) , 4-17
Study of the correlation between flexible food packaging peeling resistance and surface composition for aluminum-metallized BOPP films aged at 60°C
This study investigated the correlation between surface composition and peeling resistance in food packaging films by studying the heat aging of fabricated films over varying periods of time. The films consisted of a layer of aluminum (Al) metallized, biaxially oriented polypropylene (BOPP) bonded with a polyurethane (PU) adhesive onto another polymeric layer of low-density polyethylene (LDPE). The Al metallized films were prepared by physical vapor deposition (PVD) and aged at 60°C for either 5 or 15 days. The resulting aluminum surfaces were analyzed using X-ray photoelectron spectroscopy (XPS) and found to contain aluminum oxide (Al2O3) and trihydroxide (Al(OH)3). The XPS characterization also revealed a 29% increase in the Al(OH)3 layer thickness of the aged sample relative to a non-aged sample. Atomic force microscopy (AFM) was applied on investigations of possible morphology changes. The aluminum and PU adhesive surface energies were also determined using contact angles measurements and the aluminum surface energy was found to increase by as much as 11.7% compared to the non-aged sample, while the PU adhesive surface energy was at least 65% higher than that of the metallic substrate. The peeling resistance of the laminated aluminum was determined by average peel strength measurements and it was found that the variation in peel strength was related to changes in the Al2O3 layer thickness. The delaminated samples were analyzed using scanning electron microscopy/energy dispersive X-ray spectrometry (SEM/EDS) and showed the cohesive failure of the aluminum film.
- 1 January 2016
- Published by Department of Polymer Engineering, Scientific Society of Mechanical Engineering in Express Polymer Letters
- Vol. 10 (11) , 927-940
Bio-based polyurethane prepared from Kraft lignin and modified castor oil
Current challenges highlight the need for polymer research using renewable natural sources as a substitute for petroleum-based polymers. The use of polyols obtained from renewable sources combined with the reuse of industrial residues such as lignin is an important agent in this process. Different compositions of polyurethane-type materials were prepared by combining technical Kraft lignin (TKL) with castor oil (CO) or modified castor oil (MCO1 and MCO2) to increase their reactivity towards diphenylmethane diisocyanate (MDI). The results indicate that lignin increases the glass transition temperature, the crosslinking density and improves the ultimate stress especially for those prepared from MCO2 and 30% lignin content from 8.2 MPa (lignin free) to 23.5 MPa. Scanning electron microscopy (SEM) micrographs of rupture surface after uniaxial tensile tests show ductile-to-brittle transition. The results show the possibility to develop polyurethane-type materials, varying technical grade Kraft lignin content, which cover a wide range of mechanical properties (from large elastic/low Young modulus to brittle/high Young modulus polyurethanes)
- 1 January 2016
- Published by Department of Polymer Engineering, Scientific Society of Mechanical Engineering in Express Polymer Letters
- Vol. 10 (11) , 927-940
Bio-based polyurethane prepared from Kraft lignin and modified castor oil
Current challenges highlight the need for polymer research using renewable natural sources as a substitute for petroleum-based polymers. The use of polyols obtained from renewable sources combined with the reuse of industrial residues such as lignin is an important agent in this process. Different compositions of polyurethane-type materials were prepared by combining technical Kraft lignin (TKL) with castor oil (CO) or modified castor oil (MCO1 and MCO2) to increase their reactivity towards diphenylmethane diisocyanate (MDI). The results indicate that lignin increases the glass transition temperature, the crosslinking density and improves the ultimate stress especially for those prepared from MCO2 and 30% lignin content from 8.2 MPa (lignin free) to 23.5 MPa. Scanning electron microscopy (SEM) micrographs of rupture surface after uniaxial tensile tests show ductile-to-brittle transition. The results show the possibility to develop polyurethane-type materials, varying technical grade Kraft lignin content, which cover a wide range of mechanical properties (from large elastic/low Young modulus to brittle/high Young modulus polyurethanes)